//****************************************************************************
//
//! The delay function uses timer to implement the delay time in milliseconds
//!
//! \param time in millisecond
//
//! \return void
//****************************************************************************
static void delay(int time_ms)
{
// Initialize Timer 0B as one-shot down counter.
MAP_PRCMPeripheralClkEnable(PRCM_TIMERA0, PRCM_RUN_MODE_CLK);
MAP_PRCMPeripheralReset(PRCM_TIMERA0);
MAP_TimerConfigure(TIMERA0_BASE, TIMER_CFG_SPLIT_PAIR | TIMER_CFG_B_ONE_SHOT);
MAP_TimerPrescaleSet(TIMERA0_BASE, TIMER_B, PRESCALE);
//Load the value in milisecond
MAP_TimerLoadSet(TIMERA0_BASE, TIMER_B, MILLISECONDS_TO_TICKS(time_ms));
// Enable the timer
MAP_TimerEnable(TIMERA0_BASE, TIMER_B);
//Stall during debug
MAP_TimerControlStall(TIMERA0_BASE, TIMER_B, 1);
// Enable interrupt upon Time-out
MAP_TimerIntEnable(TIMERA0_BASE, TIMER_TIMB_TIMEOUT);
// Clear Interrupt Flag
MAP_TimerIntClear(TIMERA0_BASE, MAP_TimerIntStatus(TIMERA0_BASE, true));
//Wait until timer time-out
while (MAP_TimerIntStatus(TIMERA0_BASE, true) != TIMER_TIMB_TIMEOUT){}
//Disable the timer
MAP_TimerDisable(TIMERA0_BASE, TIMER_B);
//Disable Interrupt
MAP_TimerIntDisable(TIMERA0_BASE, TIMER_TIMB_TIMEOUT);
MAP_TimerIntUnregister(TIMERA0_BASE, TIMER_B);
}
int main(void) {
SystemInit();
/*Initialize Erika related stuffs*/
EE_system_init();
/*Initialize systick */
EE_systick_set_period(MILLISECONDS_TO_TICKS(1, SystemCoreClock));
EE_systick_enable_int();
EE_systick_start();
console_init();
stop = 0;
calcRawSpeed();
initState(kwips_rawspeed, initAlarms, initFreq, initKWPP);
do
{
ch = readCharUSART();
} while (ch != 't');
ActivateTask(SuperTask);
StartOS(OSDEFAULTAPPMODE);
/* Forever loop: background activities (if any) should go here */
for (;;) {
}
}
/* Increase Autoscroll rate */
void DoAutoscrollIncr( void )
{
if ( Prefs()->autoscrollInterval == AUTOSCROLL_MIN_INTERVAL_VALUE ) {
if ( Prefs()->autoscrollJump < AUTOSCROLL_MAX_JUMP_VALUE )
Prefs()->autoscrollJump += AUTOSCROLL_INCR_JUMP_VALUE;
}
else {
if ( Prefs()->autoscrollInterval <=
MILLISECONDS_TO_TICKS( AUTOSCROLL_FINE_TRANSITION ) )
Prefs()->autoscrollInterval -=
MILLISECONDS_TO_TICKS( AUTOSCROLL_FINE_INCR_INTERVAL_VALUE );
else
Prefs()->autoscrollInterval -=
MILLISECONDS_TO_TICKS( AUTOSCROLL_INCR_INTERVAL_VALUE );
}
}
/* Decrease Autoscroll rate */
void DoAutoscrollDecr( void )
{
if ( Prefs()->autoscrollJump == AUTOSCROLL_MIN_JUMP_VALUE )
{
if ( Prefs()->autoscrollInterval <
MILLISECONDS_TO_TICKS( AUTOSCROLL_FINE_TRANSITION ) )
Prefs()->autoscrollInterval +=
MILLISECONDS_TO_TICKS( AUTOSCROLL_FINE_INCR_INTERVAL_VALUE );
else if ( Prefs()->autoscrollInterval <
MILLISECONDS_TO_TICKS( AUTOSCROLL_MAX_INTERVAL_VALUE ) )
Prefs()->autoscrollInterval +=
MILLISECONDS_TO_TICKS( AUTOSCROLL_INCR_INTERVAL_VALUE );
}
else {
Prefs()->autoscrollJump -= AUTOSCROLL_INCR_JUMP_VALUE;
}
}
//*****************************************************************************
//
//! starts the timer
//!
//! \param ulBase is the base address for the timer.
//! \param ulTimer selects amoung the TIMER_A or TIMER_B or TIMER_BOTH.
//! \param ulValue is the time delay in mSec after that run out,
//! timer gives an interrupt.
//!
//! This function
//! 1. Load the Timer with the specified value.
//! 2. enables the timer.
//!
//! \return none
//!
//! \Note- HW Timer runs on 80MHz clock
//
//*****************************************************************************
void Timer_IF_Start(unsigned long ulBase, unsigned long ulTimer,
unsigned long ulValue)
{
MAP_TimerLoadSet(ulBase,ulTimer,MILLISECONDS_TO_TICKS(ulValue));
//
// Enable the GPT
//
MAP_TimerEnable(ulBase,ulTimer);
}
/*
* MAIN TASK
*/
int main(void)
{
//GPIO_InitTypeDef GPIO_InitStructure;
SystemInit();
/*Initializes Erika related stuffs*/
EE_system_init();
SWatch_state.errorStatus = errorSig;
SWatch_state.ModelData.prevZCSigState = &ZCSig;
SWatch_state.ModelData.dwork = &DWork;
/* init state machine */
SWatch_initialize(&SWatch_state,
&Bplus, &Bminus, &Btime, &Btimer, &Balarm, &Bswatch, &Bstart, &Bstop,
&hours, &minutes, &seconds, &tenths, &mode, &alarm_signal, &timer_exp);
/*Initialize systick */
EE_systick_set_period(MILLISECONDS_TO_TICKS(1, SystemCoreClock));
EE_systick_enable_int();
EE_systick_start();
/* Initializes LCD and touchscreen */
IOE_Config();
/* Initialize the LCD */
STM32f4_Discovery_LCD_Init();
// LCD_Clear(White);
/* Set the LCD Text size */
// LCD_SetFont(&Font8x12);
// Lcd_Touch_Calibration();
InitTouch(-0.102, 0.0656, -335, 10);
/* Draw the background */
DrawInit(MyWatchScr);
LCD_SetTextColor(Black);
LCD_SetBackColor(Black);
LCD_DrawFullRect(10, 80, 240, 56);
WPrint(&MyWatchScr[SEP1STR], ":");
WPrint(&MyWatchScr[SEP2STR], ":");
/* Program cyclic alarms which will fire after an initial offset,
* and after that periodically
* */
SetRelAlarm(AlarmTaskLCD, 10, 50);
SetRelAlarm(AlarmTaskClock, 10, 100);
/* Forever loop: background activities (if any) should go here */
for (;;) {
}
}
static void delayAfterWelcomeMessageShown(void)
{
unsigned int milliseconds = 0, lastInterval = 0;
lastInterval = NOW_IN_TICKS;
while (milliseconds < 5000)
{
if (TICKS_ELAPSED_SINCE(lastInterval) >= MILLISECONDS_TO_TICKS(100))
{
milliseconds += 100;
lastInterval = NOW_IN_TICKS;
}
eventUpdates();
}
}
//*****************************************************************************
//
//! main function demonstrates the use of the watchdog timer to perform system
//! reset.
//!
//! \param None
//!
//! \return None
//
//*****************************************************************************
void main(void)
{
tBoolean bRetcode;
//
// Initialize the board
//
BoardInit();
//
// Pinmuxing for LEDs
//
PinMuxConfig();
//
// configure RED LED
//
GPIO_IF_LedConfigure(LED1);
GPIO_IF_LedOff(MCU_RED_LED_GPIO);
//
// Enable the peripherals used by this example.
//
MAP_PRCMPeripheralClkEnable(PRCM_WDT, PRCM_RUN_MODE_CLK);
//
// Set up the watchdog interrupt handler.
//
WDT_IF_Init(WatchdogIntHandler, MILLISECONDS_TO_TICKS(WD_PERIOD_MS));
//
// Start the timer. Once the timer is started, it cannot be disable.
//
MAP_WatchdogEnable(WDT_BASE);
bRetcode = MAP_WatchdogRunning(WDT_BASE);
if(!bRetcode)
{
WDT_IF_DeInit();
}
//
// Loop forever while the LED winks as watchdog interrupts are handled.
//
while(FOREVER)
{
}
}
//*****************************************************************************
//
//! main function demonstrates the use of the watchdog timer to perform system
//! reset.
//!
//! \param None
//!
//! \return None
//
//*****************************************************************************
void main(void)
{
tBoolean bRetcode;
//
// Initialize the board
//
BoardInit();
//
// Pinmuxing for LEDs
//
PinMuxConfig();
//
// configure RED LED
//
GPIO_IF_LedConfigure(LED1);
GPIO_IF_LedOff(MCU_RED_LED_GPIO);
//
// Set up the watchdog interrupt handler.
//
WDT_IF_Init(WatchdogIntHandler, MILLISECONDS_TO_TICKS(WD_PERIOD_MS));
bRetcode = MAP_WatchdogRunning(WDT_BASE);
if(!bRetcode)
{
WDT_IF_DeInit();
}
//
// Loop forever while the LED winks as watchdog interrupts are handled.
//
while(FOREVER)
{
}
}
//*****************************************************************************
//
//! \brief Connecting to a WLAN Accesspoint
//! This function connects to the required AP (SSID_NAME).
//! This code example assumes the AP doesn't use WIFI security.
//! The function will return only once we are connected
//! and have acquired IP address
//!
//! \param[in] None
//!
//! \return 0 means success, -1 means failure
//!
//! \note
//!
//! \warning If the WLAN connection fails or we don't aquire an IP address,
//! We will be stuck in this function forever.
//
//*****************************************************************************
int WlanConnect()
{
int iRetCode = 0;
int iRetVal = 0;
int iConnect = 0;
unsigned char ucQueueMsg = 0;
SlSecParams_t secParams;
secParams.Key = (signed char *)SECURITY_KEY;
secParams.KeyLen = strlen((const char *)secParams.Key);
secParams.Type = SECURITY_TYPE;
//
// Set up the watchdog interrupt handler.
//
WDT_IF_Init(WatchdogIntHandler, MILLISECONDS_TO_TICKS(WD_PERIOD_MS));
/* Enabling the Sleep clock for the Watch Dog Timer*/
MAP_PRCMPeripheralClkEnable(PRCM_WDT, PRCM_SLP_MODE_CLK);
g_ucFeedWatchdog = 1;
g_ucWdogCount = 0;
while(!(ucQueueMsg & (EVENT_IP_ACQUIRED|CONNECTION_FAILED)))
{
UART_PRINT("Trying to connect to AP: ");
UART_PRINT(SSID_NAME);
UART_PRINT("\n\r");
sl_WlanConnect((signed char *)SSID_NAME,
strlen((const char *)SSID_NAME), 0, &secParams, 0);
iConnect = 0;
do{
osi_MsgQRead(&g_tConnection, &ucQueueMsg, OSI_WAIT_FOREVER);
switch(ucQueueMsg)
{
case EVENT_CONNECTION:
iConnect = 1;
break;
case EVENT_IP_ACQUIRED:
iRetVal = 0;
break;
case WDOG_EXPIRED:
//
// disconnect from the Access Point
//
if(iConnect)
{
WlanDisconnect();
}
//
// stop the simplelink with reqd. timeout value (30 ms)
//
sl_Stop(SL_STOP_TIMEOUT);
UART_PRINT("sl stop\n\r");
MAP_UtilsDelay(8000);
//
// starting the simplelink
//
sl_Start(NULL, NULL, NULL);
UART_PRINT("sl start\n\r");
break;
case EVENT_DISCONNECTION:
iConnect = 0;
break;
case CONNECTION_FAILED:
iRetVal = -1;
break;
default:
UART_PRINT("unexpected event\n\r");
break;
}
}while(ucQueueMsg == (unsigned char)EVENT_CONNECTION);
}
iRetCode = MAP_WatchdogRunning(WDT_BASE);
if(iRetCode)
{
WDT_IF_DeInit();
MAP_PRCMPeripheralClkDisable(PRCM_WDT, PRCM_RUN_MODE_CLK);
}
ASSERT_ON_ERROR(iRetVal);
return(iRetVal);
}
//****************************************************************************
// MAIN FUNCTION
//****************************************************************************
void main()
{
long lRetVal = 0;
char data[BUF_SIZE];
char sent_data[BUF_SIZE];
unsigned char highByte, lowByte;
int i;
unsigned long tempStartTimeStamp, tempStopTimeStamp;
memset(sent_data, 0, 10);
// Board Initialization
BoardInit();
// Configure the pinmux settings for the peripherals exercised
PinMuxConfig();
// Initialize the PWM outputs on the board
InitServos();
// Initialize the sensor ADC
InitSensorADC();
// Configuring UART
InitTerm();
// Display banner
DisplayBanner(APPLICATION_NAME);
// Connect to WIFI using default info
//WlanConnect(NULL, NULL, NULL);
WlanConnect("Nagui's Network", "SL_SEC_TYPE_WPA", "19520605");
// Setup the TCP Server Socket
BsdTcpServerSetup(PORT_NUM);
// Recieve Data
while (lRetVal >= 0)
{
lRetVal = BsdTcpServerReceive(data);
//SysTickPeriodSet(800000000); // test
//SysTickEnable(); // test
Timer_IF_Init(PRCM_TIMERA0, TIMERA0_BASE, TIMER_CFG_PERIODIC, TIMER_A, 0);
Timer_IF_Start(TIMERA0_BASE, TIMER_A, MILLISECONDS_TO_TICKS(2000));
//tempStartTimeStamp = SysTickValueGet(); // test
tempStartTimeStamp = Timer_IF_GetCount(TIMERA0_BASE, TIMER_A);
for (i = 0; i<NUM_SERVOS; i++)
{
MoveServo((unsigned char)data[i], (enum Servo_Joint_Type)i);
UART_PRINT("%d", (unsigned int) data[i]);
}
for (i = 0; i< NUM_SENSORS; i++)
{
//UnsignedShort_to_UnsignedChar(GetSensorReading((enum Fingertip_Sensor_Type)i), &highByte, &lowByte);
UnsignedShort_to_UnsignedChar(GetSensorReading(SENSOR_FINGER_INDEX), &highByte, &lowByte);
sent_data[i*2] = (char)highByte;
sent_data[i*2+1] = (char)lowByte;
}
//tempStopTimeStamp = SysTickValueGet(); // test
tempStopTimeStamp = Timer_IF_GetCount(TIMERA0_BASE, TIMER_A);
lRetVal = BsdTcpServerSend(sent_data, 10);
UART_PRINT("timestamp start: %lu\n\r", tempStartTimeStamp); //test
UART_PRINT("timestamp stop: %lu\n\r", tempStopTimeStamp); //test
UART_PRINT("Sent 10 bytes to client.\n\r");
}
UART_PRINT("Exiting Application ...\n\r");
// power of the Network processor
lRetVal = sl_Stop(SL_STOP_TIMEOUT);
}
//*****************************************************************************
//
//! starts the timer
//!
//! \param ulBase is the base address for the timer.
//! \param ulTimer selects between the TIMER A and TIMER B.
//! \param ulValue is timer reload value (mSec) after which the timer will run out and gives an interrupt.
//!
//! This function
//! 1. Reload the Timer with the specified value.
//!
//! \return none
//
//*****************************************************************************
void Timer_IF_ReLoad(unsigned long ulBase, unsigned long ulTimer,
unsigned long ulValue)
{
MAP_TimerLoadSet(ulBase,ulTimer,MILLISECONDS_TO_TICKS(ulValue));
}