void Magnetometer_Get(struct ParseState *Parser, struct Value *ReturnValue, struct Value **Param, int NumArgs)
{
if (Param[0]->Val->Pointer == NULL)
return;
MagnetometerData data;
MagnetometerGet(&data);
// use the same struct like picoc. see below
struct mystruct {
double x;
double y;
double z;
} *pdata;
pdata = Param[0]->Val->Pointer;
pdata->x = data.x;
pdata->y = data.y;
pdata->z = data.z;
}
/**
* @brief Use the INSGPS fusion algorithm in either indoor or outdoor mode (use GPS)
* @params[in] first_run This is the first run so trigger reinitialization
* @params[in] outdoor_mode If true use the GPS for position, if false weakly pull to (0,0)
* @return 0 for success, -1 for failure
*/
static int32_t updateAttitudeINSGPS(bool first_run, bool outdoor_mode)
{
UAVObjEvent ev;
GyrosData gyrosData;
AccelsData accelsData;
MagnetometerData magData;
BaroAltitudeData baroData;
GPSPositionData gpsData;
GPSVelocityData gpsVelData;
GyrosBiasData gyrosBias;
static bool mag_updated = false;
static bool baro_updated;
static bool gps_updated;
static bool gps_vel_updated;
static float baroOffset = 0;
static uint32_t ins_last_time = 0;
static bool inited;
float NED[3] = {0.0f, 0.0f, 0.0f};
float vel[3] = {0.0f, 0.0f, 0.0f};
float zeros[3] = {0.0f, 0.0f, 0.0f};
// Perform the update
uint16_t sensors = 0;
float dT;
// Wait until the gyro and accel object is updated, if a timeout then go to failsafe
if ( (xQueueReceive(gyroQueue, &ev, FAILSAFE_TIMEOUT_MS / portTICK_RATE_MS) != pdTRUE) ||
(xQueueReceive(accelQueue, &ev, 1 / portTICK_RATE_MS) != pdTRUE) )
{
// Do not set attitude timeout warnings in simulation mode
if (!AttitudeActualReadOnly()){
AlarmsSet(SYSTEMALARMS_ALARM_ATTITUDE,SYSTEMALARMS_ALARM_WARNING);
return -1;
}
}
if (inited) {
mag_updated = 0;
baro_updated = 0;
gps_updated = 0;
gps_vel_updated = 0;
}
if (first_run) {
inited = false;
init_stage = 0;
mag_updated = 0;
baro_updated = 0;
gps_updated = 0;
gps_vel_updated = 0;
ins_last_time = PIOS_DELAY_GetRaw();
return 0;
}
mag_updated |= (xQueueReceive(magQueue, &ev, 0 / portTICK_RATE_MS) == pdTRUE);
baro_updated |= xQueueReceive(baroQueue, &ev, 0 / portTICK_RATE_MS) == pdTRUE;
gps_updated |= (xQueueReceive(gpsQueue, &ev, 0 / portTICK_RATE_MS) == pdTRUE) && outdoor_mode;
gps_vel_updated |= (xQueueReceive(gpsVelQueue, &ev, 0 / portTICK_RATE_MS) == pdTRUE) && outdoor_mode;
// Get most recent data
GyrosGet(&gyrosData);
AccelsGet(&accelsData);
MagnetometerGet(&magData);
BaroAltitudeGet(&baroData);
GPSPositionGet(&gpsData);
GPSVelocityGet(&gpsVelData);
GyrosBiasGet(&gyrosBias);
// Discard mag if it has NAN (normally from bad calibration)
mag_updated &= (magData.x == magData.x && magData.y == magData.y && magData.z == magData.z);
// Don't require HomeLocation.Set to be true but at least require a mag configuration (allows easily
// switching between indoor and outdoor mode with Set = false)
mag_updated &= (homeLocation.Be[0] != 0 || homeLocation.Be[1] != 0 || homeLocation.Be[2]);
// Have a minimum requirement for gps usage
gps_updated &= (gpsData.Satellites >= 7) && (gpsData.PDOP <= 4.0f) && (homeLocation.Set == HOMELOCATION_SET_TRUE);
if (!inited)
AlarmsSet(SYSTEMALARMS_ALARM_ATTITUDE,SYSTEMALARMS_ALARM_ERROR);
else if (outdoor_mode && gpsData.Satellites < 7)
AlarmsSet(SYSTEMALARMS_ALARM_ATTITUDE,SYSTEMALARMS_ALARM_ERROR);
else
AlarmsClear(SYSTEMALARMS_ALARM_ATTITUDE);
if (!inited && mag_updated && baro_updated && (gps_updated || !outdoor_mode)) {
// Don't initialize until all sensors are read
if (init_stage == 0 && !outdoor_mode) {
float Pdiag[16]={25.0f,25.0f,25.0f,5.0f,5.0f,5.0f,1e-5f,1e-5f,1e-5f,1e-5f,1e-5f,1e-5f,1e-5f,1e-4f,1e-4f,1e-4f};
float q[4];
float pos[3] = {0.0f, 0.0f, 0.0f};
// Initialize barometric offset to homelocation altitude
baroOffset = -baroData.Altitude;
pos[2] = -(baroData.Altitude + baroOffset);
// Reset the INS algorithm
INSGPSInit();
INSSetMagVar(revoCalibration.mag_var);
INSSetAccelVar(revoCalibration.accel_var);
INSSetGyroVar(revoCalibration.gyro_var);
INSSetBaroVar(revoCalibration.baro_var);
// Initialize the gyro bias from the settings
float gyro_bias[3] = {gyrosBias.x * F_PI / 180.0f, gyrosBias.y * F_PI / 180.0f, gyrosBias.z * F_PI / 180.0f};
INSSetGyroBias(gyro_bias);
xQueueReceive(magQueue, &ev, 100 / portTICK_RATE_MS);
MagnetometerGet(&magData);
// Set initial attitude
AttitudeActualData attitudeActual;
attitudeActual.Roll = atan2f(-accelsData.y, -accelsData.z) * 180.0f / F_PI;
attitudeActual.Pitch = atan2f(accelsData.x, -accelsData.z) * 180.0f / F_PI;
attitudeActual.Yaw = atan2f(-magData.y, magData.x) * 180.0f / F_PI;
RPY2Quaternion(&attitudeActual.Roll,&attitudeActual.q1);
AttitudeActualSet(&attitudeActual);
q[0] = attitudeActual.q1;
q[1] = attitudeActual.q2;
q[2] = attitudeActual.q3;
q[3] = attitudeActual.q4;
INSSetState(pos, zeros, q, zeros, zeros);
INSResetP(Pdiag);
} else if (init_stage == 0 && outdoor_mode) {
float Pdiag[16]={25.0f,25.0f,25.0f,5.0f,5.0f,5.0f,1e-5f,1e-5f,1e-5f,1e-5f,1e-5f,1e-5f,1e-5f,1e-4f,1e-4f,1e-4f};
float q[4];
float NED[3];
// Reset the INS algorithm
INSGPSInit();
INSSetMagVar(revoCalibration.mag_var);
INSSetAccelVar(revoCalibration.accel_var);
INSSetGyroVar(revoCalibration.gyro_var);
INSSetBaroVar(revoCalibration.baro_var);
INSSetMagNorth(homeLocation.Be);
// Initialize the gyro bias from the settings
float gyro_bias[3] = {gyrosBias.x * F_PI / 180.0f, gyrosBias.y * F_PI / 180.0f, gyrosBias.z * F_PI / 180.0f};
INSSetGyroBias(gyro_bias);
GPSPositionData gpsPosition;
GPSPositionGet(&gpsPosition);
// Transform the GPS position into NED coordinates
getNED(&gpsPosition, NED);
// Initialize barometric offset to cirrent GPS NED coordinate
baroOffset = -NED[2] - baroData.Altitude;
xQueueReceive(magQueue, &ev, 100 / portTICK_RATE_MS);
MagnetometerGet(&magData);
// Set initial attitude
AttitudeActualData attitudeActual;
attitudeActual.Roll = atan2f(-accelsData.y, -accelsData.z) * 180.0f / F_PI;
attitudeActual.Pitch = atan2f(accelsData.x, -accelsData.z) * 180.0f / F_PI;
attitudeActual.Yaw = atan2f(-magData.y, magData.x) * 180.0f / F_PI;
RPY2Quaternion(&attitudeActual.Roll,&attitudeActual.q1);
AttitudeActualSet(&attitudeActual);
q[0] = attitudeActual.q1;
q[1] = attitudeActual.q2;
q[2] = attitudeActual.q3;
q[3] = attitudeActual.q4;
INSSetState(NED, zeros, q, zeros, zeros);
INSResetP(Pdiag);
} else if (init_stage > 0) {
// Run prediction a bit before any corrections
dT = PIOS_DELAY_DiffuS(ins_last_time) / 1.0e6f;
GyrosBiasGet(&gyrosBias);
float gyros[3] = {(gyrosData.x + gyrosBias.x) * F_PI / 180.0f,
(gyrosData.y + gyrosBias.y) * F_PI / 180.0f,
(gyrosData.z + gyrosBias.z) * F_PI / 180.0f};
INSStatePrediction(gyros, &accelsData.x, dT);
AttitudeActualData attitude;
AttitudeActualGet(&attitude);
attitude.q1 = Nav.q[0];
attitude.q2 = Nav.q[1];
attitude.q3 = Nav.q[2];
attitude.q4 = Nav.q[3];
Quaternion2RPY(&attitude.q1,&attitude.Roll);
AttitudeActualSet(&attitude);
}
init_stage++;
if(init_stage > 10)
inited = true;
ins_last_time = PIOS_DELAY_GetRaw();
return 0;
}
if (!inited)
return 0;
dT = PIOS_DELAY_DiffuS(ins_last_time) / 1.0e6f;
ins_last_time = PIOS_DELAY_GetRaw();
// This should only happen at start up or at mode switches
if(dT > 0.01f)
dT = 0.01f;
else if(dT <= 0.001f)
dT = 0.001f;
// If the gyro bias setting was updated we should reset
// the state estimate of the EKF
if(gyroBiasSettingsUpdated) {
float gyro_bias[3] = {gyrosBias.x * F_PI / 180.0f, gyrosBias.y * F_PI / 180.0f, gyrosBias.z * F_PI / 180.0f};
INSSetGyroBias(gyro_bias);
gyroBiasSettingsUpdated = false;
}
// Because the sensor module remove the bias we need to add it
// back in here so that the INS algorithm can track it correctly
float gyros[3] = {gyrosData.x * F_PI / 180.0f, gyrosData.y * F_PI / 180.0f, gyrosData.z * F_PI / 180.0f};
if (revoCalibration.BiasCorrectedRaw == REVOCALIBRATION_BIASCORRECTEDRAW_TRUE) {
gyros[0] += gyrosBias.x * F_PI / 180.0f;
gyros[1] += gyrosBias.y * F_PI / 180.0f;
gyros[2] += gyrosBias.z * F_PI / 180.0f;
}
// Advance the state estimate
INSStatePrediction(gyros, &accelsData.x, dT);
// Copy the attitude into the UAVO
AttitudeActualData attitude;
AttitudeActualGet(&attitude);
attitude.q1 = Nav.q[0];
attitude.q2 = Nav.q[1];
attitude.q3 = Nav.q[2];
attitude.q4 = Nav.q[3];
Quaternion2RPY(&attitude.q1,&attitude.Roll);
AttitudeActualSet(&attitude);
// Advance the covariance estimate
INSCovariancePrediction(dT);
if(mag_updated)
sensors |= MAG_SENSORS;
if(baro_updated)
sensors |= BARO_SENSOR;
INSSetMagNorth(homeLocation.Be);
if (gps_updated && outdoor_mode)
{
INSSetPosVelVar(revoCalibration.gps_var[REVOCALIBRATION_GPS_VAR_POS], revoCalibration.gps_var[REVOCALIBRATION_GPS_VAR_VEL]);
sensors |= POS_SENSORS;
if (0) { // Old code to take horizontal velocity from GPS Position update
sensors |= HORIZ_SENSORS;
vel[0] = gpsData.Groundspeed * cosf(gpsData.Heading * F_PI / 180.0f);
vel[1] = gpsData.Groundspeed * sinf(gpsData.Heading * F_PI / 180.0f);
vel[2] = 0;
}
// Transform the GPS position into NED coordinates
getNED(&gpsData, NED);
// Track barometric altitude offset with a low pass filter
baroOffset = BARO_OFFSET_LOWPASS_ALPHA * baroOffset +
(1.0f - BARO_OFFSET_LOWPASS_ALPHA )
* ( -NED[2] - baroData.Altitude );
} else if (!outdoor_mode) {
INSSetPosVelVar(1e2f, 1e2f);
vel[0] = vel[1] = vel[2] = 0;
NED[0] = NED[1] = 0;
NED[2] = -(baroData.Altitude + baroOffset);
sensors |= HORIZ_SENSORS | HORIZ_POS_SENSORS;
sensors |= POS_SENSORS |VERT_SENSORS;
}
if (gps_vel_updated && outdoor_mode) {
sensors |= HORIZ_SENSORS | VERT_SENSORS;
vel[0] = gpsVelData.North;
vel[1] = gpsVelData.East;
vel[2] = gpsVelData.Down;
}
/*
* TODO: Need to add a general sanity check for all the inputs to make sure their kosher
* although probably should occur within INS itself
*/
if (sensors)
INSCorrection(&magData.x, NED, vel, ( baroData.Altitude + baroOffset ), sensors);
// Copy the position and velocity into the UAVO
PositionActualData positionActual;
PositionActualGet(&positionActual);
positionActual.North = Nav.Pos[0];
positionActual.East = Nav.Pos[1];
positionActual.Down = Nav.Pos[2];
PositionActualSet(&positionActual);
VelocityActualData velocityActual;
VelocityActualGet(&velocityActual);
velocityActual.North = Nav.Vel[0];
velocityActual.East = Nav.Vel[1];
velocityActual.Down = Nav.Vel[2];
VelocityActualSet(&velocityActual);
if (revoCalibration.BiasCorrectedRaw == REVOCALIBRATION_BIASCORRECTEDRAW_TRUE && !gyroBiasSettingsUpdated) {
// Copy the gyro bias into the UAVO except when it was updated
// from the settings during the calculation, then consume it
// next cycle
gyrosBias.x = Nav.gyro_bias[0] * 180.0f / F_PI;
gyrosBias.y = Nav.gyro_bias[1] * 180.0f / F_PI;
gyrosBias.z = Nav.gyro_bias[2] * 180.0f / F_PI;
GyrosBiasSet(&gyrosBias);
}
return 0;
}
/*
* Although yaw correction is done in horizontal plane, it is
* computed in 3 dimensions, just in case we change our minds later.
*/
void yaw_drift_MagGPS(float Rbe[3][3], bool gpsNewData_flag, bool magNewData_flag, float *errYaw_b)
{
#if defined (PIOS_INCLUDE_GPS) || defined (PIOS_INCLUDE_MAGNETOMETER)
// Form the horizontal direction over ground based on rmat
float horizDirOverGndRmat[3];
//Define forward vector in earth frame, Rbe' * [1;0;0], and eliminate vertical component from vector
horizDirOverGndRmat[0] = Rbe[0][0];
horizDirOverGndRmat[1] = Rbe[0][1];
horizDirOverGndRmat[2] = 0;
#if defined (PIOS_INCLUDE_GPS)
if (gpsNewData_flag) {
GPSVelocityData gpsVelocity;
GPSVelocityGet(&gpsVelocity);
if (fabs(gpsVelocity.North) > GPS_SPEED_MIN
|| fabs(gpsVelocity.East) > GPS_SPEED_MIN) {
float errorGPSYaw_e;
float errorGPSYaw_b[3];
float normGPS =
sqrtf(gpsVelocity.North * gpsVelocity.North +
gpsVelocity.East * gpsVelocity.East);
float horizDirOverGndGPS[3] = { gpsVelocity.North / normGPS, gpsVelocity.East / normGPS, 0 }; //Normalized vector
// vector cross product to get the rotation error in ground frame. However, save several processor cycles by
// condensing the math to take advantage of the cross products null entries on the x and y elements.
// errorGPSYaw_e = horizDirOverGndRmat X horizDirOverGndGPS
errorGPSYaw_e =
horizDirOverGndRmat[0] * horizDirOverGndGPS[1] -
horizDirOverGndGPS[0] * horizDirOverGndRmat[1];
// Rotate error to body frame. Again, take advantage of the yaw error vector [0;0;errorGPSYaw_e]'s null entries
// errorGPSYaw_b = Rbe * errorGPSYaw_e;
errorGPSYaw_b[0] = Rbe[0][2] * errorGPSYaw_e;
errorGPSYaw_b[1] = Rbe[1][2] * errorGPSYaw_e;
errorGPSYaw_b[2] = Rbe[2][2] * errorGPSYaw_e;
//Sum error with existing error
errYaw_b[0] += errorGPSYaw_b[0] * GPS_YAW_KP;
errYaw_b[1] += errorGPSYaw_b[1] * GPS_YAW_KP;
errYaw_b[2] += errorGPSYaw_b[2] * GPS_YAW_KP;
}
}
#endif
// TODO: Create a flag to indicate whether mag data is present (or check for updates of MagnetometerData)
#if defined (PIOS_INCLUDE_MAGNETOMETER)
if (magNewData_flag) {
MagnetometerData magnetometerData;
MagnetometerGet(&magnetometerData);
float errorMagYaw_e;
float errorMagYaw_b[3];
float horizDirOverGndMag[3];
float mags_b[3] = { magnetometerData.x, magnetometerData.y, magnetometerData.z };
// Rotate magnetometer to earth frame and eliminate vertical component
rot_mult(Rbe, mags_b, horizDirOverGndMag, true);
horizDirOverGndMag[2] = 0;
//Compute norm
float normMag = VectorMagnitude(horizDirOverGndMag);
//Normalize mag_vector. Recall that horizDirOverGndMag[2]=0
horizDirOverGndMag[0] /= normMag;
horizDirOverGndMag[1] /= normMag;
// vector cross product to get the rotation error in ground frame. However, save several processor cycles by
// condensing the math to take advantage of the cross products null entries on the x and y elements.
// errorMagYaw_e = horizDirOverGndRmat X horizDirOverGndMag
errorMagYaw_e = horizDirOverGndRmat[0] * horizDirOverGndMag[1] -
horizDirOverGndMag[0] * horizDirOverGndRmat[1];
// Rotate error to body frame. Again, take advantage of the yaw error vector [0;0;errorGPSYaw_e]'s null entries
// errorMagYaw_b = Rbe * errorMagYaw_e;
errorMagYaw_b[0] = Rbe[0][2] * errorMagYaw_e;
errorMagYaw_b[1] = Rbe[1][2] * errorMagYaw_e;
errorMagYaw_b[2] = Rbe[2][2] * errorMagYaw_e;
errYaw_b[0] += errorMagYaw_b[0] * MAG_YAW_KP;
errYaw_b[1] += errorMagYaw_b[1] * MAG_YAW_KP;
errYaw_b[2] += errorMagYaw_b[2] * MAG_YAW_KP;
}
#endif
#endif
}
static int32_t updateAttitudeComplementary(bool first_run)
{
UAVObjEvent ev;
GyrosData gyrosData;
AccelsData accelsData;
static int32_t timeval;
float dT;
static uint8_t init = 0;
// Wait until the AttitudeRaw object is updated, if a timeout then go to failsafe
if ( xQueueReceive(gyroQueue, &ev, FAILSAFE_TIMEOUT_MS / portTICK_RATE_MS) != pdTRUE ||
xQueueReceive(accelQueue, &ev, 1 / portTICK_RATE_MS) != pdTRUE )
{
// When one of these is updated so should the other
// Do not set attitude timeout warnings in simulation mode
if (!AttitudeActualReadOnly()){
AlarmsSet(SYSTEMALARMS_ALARM_ATTITUDE,SYSTEMALARMS_ALARM_WARNING);
return -1;
}
}
AccelsGet(&accelsData);
// During initialization and
FlightStatusData flightStatus;
FlightStatusGet(&flightStatus);
if(first_run) {
#if defined(PIOS_INCLUDE_HMC5883)
// To initialize we need a valid mag reading
if ( xQueueReceive(magQueue, &ev, 0 / portTICK_RATE_MS) != pdTRUE )
return -1;
MagnetometerData magData;
MagnetometerGet(&magData);
#else
MagnetometerData magData;
magData.x = 100;
magData.y = 0;
magData.z = 0;
#endif
AttitudeActualData attitudeActual;
AttitudeActualGet(&attitudeActual);
init = 0;
attitudeActual.Roll = atan2f(-accelsData.y, -accelsData.z) * 180.0f / F_PI;
attitudeActual.Pitch = atan2f(accelsData.x, -accelsData.z) * 180.0f / F_PI;
attitudeActual.Yaw = atan2f(-magData.y, magData.x) * 180.0f / F_PI;
RPY2Quaternion(&attitudeActual.Roll,&attitudeActual.q1);
AttitudeActualSet(&attitudeActual);
timeval = PIOS_DELAY_GetRaw();
return 0;
}
if((init == 0 && xTaskGetTickCount() < 7000) && (xTaskGetTickCount() > 1000)) {
// For first 7 seconds use accels to get gyro bias
attitudeSettings.AccelKp = 1;
attitudeSettings.AccelKi = 0.9;
attitudeSettings.YawBiasRate = 0.23;
magKp = 1;
} else if ((attitudeSettings.ZeroDuringArming == ATTITUDESETTINGS_ZERODURINGARMING_TRUE) && (flightStatus.Armed == FLIGHTSTATUS_ARMED_ARMING)) {
attitudeSettings.AccelKp = 1;
attitudeSettings.AccelKi = 0.9;
attitudeSettings.YawBiasRate = 0.23;
magKp = 1;
init = 0;
} else if (init == 0) {
// Reload settings (all the rates)
AttitudeSettingsGet(&attitudeSettings);
magKp = 0.01f;
init = 1;
}
GyrosGet(&gyrosData);
// Compute the dT using the cpu clock
dT = PIOS_DELAY_DiffuS(timeval) / 1000000.0f;
timeval = PIOS_DELAY_GetRaw();
float q[4];
AttitudeActualData attitudeActual;
AttitudeActualGet(&attitudeActual);
float grot[3];
float accel_err[3];
// Get the current attitude estimate
quat_copy(&attitudeActual.q1, q);
// Rotate gravity to body frame and cross with accels
grot[0] = -(2 * (q[1] * q[3] - q[0] * q[2]));
grot[1] = -(2 * (q[2] * q[3] + q[0] * q[1]));
grot[2] = -(q[0] * q[0] - q[1]*q[1] - q[2]*q[2] + q[3]*q[3]);
CrossProduct((const float *) &accelsData.x, (const float *) grot, accel_err);
// Account for accel magnitude
accel_mag = accelsData.x*accelsData.x + accelsData.y*accelsData.y + accelsData.z*accelsData.z;
accel_mag = sqrtf(accel_mag);
accel_err[0] /= accel_mag;
accel_err[1] /= accel_mag;
accel_err[2] /= accel_mag;
if ( xQueueReceive(magQueue, &ev, 0) != pdTRUE )
{
// Rotate gravity to body frame and cross with accels
float brot[3];
float Rbe[3][3];
MagnetometerData mag;
Quaternion2R(q, Rbe);
MagnetometerGet(&mag);
// If the mag is producing bad data don't use it (normally bad calibration)
if (mag.x == mag.x && mag.y == mag.y && mag.z == mag.z) {
rot_mult(Rbe, homeLocation.Be, brot);
float mag_len = sqrtf(mag.x * mag.x + mag.y * mag.y + mag.z * mag.z);
mag.x /= mag_len;
mag.y /= mag_len;
mag.z /= mag_len;
float bmag = sqrtf(brot[0] * brot[0] + brot[1] * brot[1] + brot[2] * brot[2]);
brot[0] /= bmag;
brot[1] /= bmag;
brot[2] /= bmag;
// Only compute if neither vector is null
if (bmag < 1 || mag_len < 1)
mag_err[0] = mag_err[1] = mag_err[2] = 0;
else
CrossProduct((const float *) &mag.x, (const float *) brot, mag_err);
}
} else {
mag_err[0] = mag_err[1] = mag_err[2] = 0;
}
// Accumulate integral of error. Scale here so that units are (deg/s) but Ki has units of s
GyrosBiasData gyrosBias;
GyrosBiasGet(&gyrosBias);
gyrosBias.x -= accel_err[0] * attitudeSettings.AccelKi;
gyrosBias.y -= accel_err[1] * attitudeSettings.AccelKi;
gyrosBias.z -= mag_err[2] * magKi;
GyrosBiasSet(&gyrosBias);
// Correct rates based on error, integral component dealt with in updateSensors
gyrosData.x += accel_err[0] * attitudeSettings.AccelKp / dT;
gyrosData.y += accel_err[1] * attitudeSettings.AccelKp / dT;
gyrosData.z += accel_err[2] * attitudeSettings.AccelKp / dT + mag_err[2] * magKp / dT;
// Work out time derivative from INSAlgo writeup
// Also accounts for the fact that gyros are in deg/s
float qdot[4];
qdot[0] = (-q[1] * gyrosData.x - q[2] * gyrosData.y - q[3] * gyrosData.z) * dT * F_PI / 180 / 2;
qdot[1] = (q[0] * gyrosData.x - q[3] * gyrosData.y + q[2] * gyrosData.z) * dT * F_PI / 180 / 2;
qdot[2] = (q[3] * gyrosData.x + q[0] * gyrosData.y - q[1] * gyrosData.z) * dT * F_PI / 180 / 2;
qdot[3] = (-q[2] * gyrosData.x + q[1] * gyrosData.y + q[0] * gyrosData.z) * dT * F_PI / 180 / 2;
// Take a time step
q[0] = q[0] + qdot[0];
q[1] = q[1] + qdot[1];
q[2] = q[2] + qdot[2];
q[3] = q[3] + qdot[3];
if(q[0] < 0) {
q[0] = -q[0];
q[1] = -q[1];
q[2] = -q[2];
q[3] = -q[3];
}
// Renomalize
qmag = sqrtf(q[0]*q[0] + q[1]*q[1] + q[2]*q[2] + q[3]*q[3]);
q[0] = q[0] / qmag;
q[1] = q[1] / qmag;
q[2] = q[2] / qmag;
q[3] = q[3] / qmag;
// If quaternion has become inappropriately short or is nan reinit.
// THIS SHOULD NEVER ACTUALLY HAPPEN
if((fabs(qmag) < 1.0e-3f) || (qmag != qmag)) {
q[0] = 1;
q[1] = 0;
q[2] = 0;
q[3] = 0;
}
quat_copy(q, &attitudeActual.q1);
// Convert into eueler degrees (makes assumptions about RPY order)
Quaternion2RPY(&attitudeActual.q1,&attitudeActual.Roll);
AttitudeActualSet(&attitudeActual);
// Flush these queues for avoid errors
xQueueReceive(baroQueue, &ev, 0);
if ( xQueueReceive(gpsQueue, &ev, 0) == pdTRUE && homeLocation.Set == HOMELOCATION_SET_TRUE ) {
float NED[3];
// Transform the GPS position into NED coordinates
GPSPositionData gpsPosition;
GPSPositionGet(&gpsPosition);
getNED(&gpsPosition, NED);
PositionActualData positionActual;
PositionActualGet(&positionActual);
positionActual.North = NED[0];
positionActual.East = NED[1];
positionActual.Down = NED[2];
PositionActualSet(&positionActual);
}
if ( xQueueReceive(gpsVelQueue, &ev, 0) == pdTRUE ) {
// Transform the GPS position into NED coordinates
GPSVelocityData gpsVelocity;
GPSVelocityGet(&gpsVelocity);
VelocityActualData velocityActual;
VelocityActualGet(&velocityActual);
velocityActual.North = gpsVelocity.North;
velocityActual.East = gpsVelocity.East;
velocityActual.Down = gpsVelocity.Down;
VelocityActualSet(&velocityActual);
}
AlarmsClear(SYSTEMALARMS_ALARM_ATTITUDE);
return 0;
}
