uint8_t ow_reset(void)
{
uint8_t err;
OW_OUT_LOW();
OW_DIR_OUT(); // pull OW-Pin low for 480us
_delay_us(480);
ATOMIC_BLOCK(ATOMIC_RESTORESTATE) {
// set Pin as input - wait for clients to pull low
OW_DIR_IN(); // input
#if OW_USE_INTERNAL_PULLUP
OW_OUT_HIGH();
#endif
_delay_us(64); // was 66
err = OW_GET_IN(); // no presence detect
// if err!=0: nobody pulled to low, still high
}
// after a delay the clients should release the line
// and input-pin gets back to high by pull-up-resistor
_delay_us(480 - 64); // was 480-66
if ( OW_GET_IN() == 0 ) {
err = 1; // short circuit, expected low but got high
}
return err;
}
uint8_t ow_reset(void)
{
uint8_t err;
uint8_t sreg;
OW_OUT_LOW(); // disable internal pull-up (maybe on from parasite)
OW_DIR_OUT(); // pull OW-Pin low for 480us
_delay_us(480);
sreg=SREG;
cli();
// set Pin as input - wait for clients to pull low
OW_DIR_IN(); // input
_delay_us(66);
err = OW_GET_IN(); // no presence detect
// nobody pulled to low, still high
SREG=sreg; // sei()
// after a delay the clients should release the line
// and input-pin gets back to high due to pull-up-resistor
_delay_us(480-66);
if( OW_GET_IN() == 0 ) // short circuit
err = 1;
return err;
}
/*********************************
*RESET
-*********************************/
uint8_t
ow_reset(void)
{ uint8_t err;
uint8_t sreg;
OW_OUT_LOW(); // disable internal pull-up (maybe on from parasite)
OW_DIR_OUT(); // pull OW-Pin low for 480us
// delay_us(480);
usecsleep(2,240);
//timer1_Delay(480);
sreg=SREG;
/*TRY it*///
CLI();
/* set Pin as input - wait for clients to pull low*/
OW_DIR_IN(); /* input*/
// delay_us(66);
usecsleep(2,33);
//timer1_Delay(480);
err = OW_GET_IN(); /* no presence detect*/
/* nobody pulled to low, still high*/
/*TRY it*///SREG=sreg; /*
SEI();
/* after a delay the clients should release the line
and input-pin gets back to high due to pull-up-resistor*/
// delay_us(480-66);
usecsleep(2,207);
//timer1_Delay(480-66);
if( OW_GET_IN() == 0 )/* short circuit*/ err = 1;
return err;
}
/* Timing issue when using runtime-bus-selection (!OW_ONE_BUS):
The master should sample at the end of the 15-slot after initiating
the read-time-slot. The variable bus-settings need more
cycles than the constant ones so the delays had to be shortened
to achive a 15uS overall delay
Setting/clearing a bit in I/O Register needs 1 cyle in OW_ONE_BUS
but around 14 cyles in configureable bus (us-Delay is 4 cyles per uS) */
uint8_t ow_bit_io( uint8_t b )
{
uint8_t sreg;
sreg=SREG;
cli();
OW_DIR_OUT(); // drive bus low
_delay_us(1); // Recovery-Time wuffwuff was 1
if ( b ) OW_DIR_IN(); // if bit is 1 set bus high (by ext. pull-up)
// wuffwuff delay was 15uS-1 see comment above
//_delay_us(15-1-OW_CONF_DELAYOFFSET);
_delay_us(15);
if( OW_GET_IN() == 0 ) b = 0; // sample at end of read-timeslot
_delay_us(60-15);
OW_DIR_IN();
SREG=sreg; // sei();
return b;
}
/* Timing issue when using runtime-bus-selection (!OW_ONE_BUS):
The master should sample at the end of the 15-slot after initiating
the read-time-slot. The variable bus-settings need more
cycles than the constant ones so the delays had to be shortened
to achive a 15uS overall delay
Setting/clearing a bit in I/O Register needs 1 cyle in OW_ONE_BUS
but around 14 cyles in configureable bus (us-Delay is 4 cyles per uS) */
uint8_t ow_bit_io( uint8_t b )
{
uint8_t sreg;
sreg=SREG;
cli();
OW_DIR_OUT(); // drive bus low
_delay_us(2); // Recovery-Time wuffwuff was 1 // normal 6 us
if ( b ) OW_DIR_IN(); // if bit is 1 set bus high (by ext. pull-up)
// wuffwuff delay was 15uS-1 see comment above
_delay_us(15-2-OW_CONF_DELAYOFFSET);
if( OW_GET_IN() == 0 ) b = 0; // sample at end of read-timeslot
_delay_us(60-15);
OW_DIR_IN();
SREG=sreg; // sei();
_delay_us(10); // bei langen Kabeln kann dieser Wert wohl auch um einiges größer sein! (recovery time)
return b;
}
/******************************************************************
Timing issue when using runtime-bus-selection (!OW_ONE_BUS):
The master should sample at the end of the 15-slot after initiating
the read-time-slot. The variable bus-settings need more
cycles than the constant ones so the delays had to be shortened
to achive a 15uS overall delay
Setting/clearing a bit in I/O Register needs 1 cyle in OW_ONE_BUS
but around 14 cyles in configureable bus (us-Delay is 4 cyles per uS)
*********************************************************************/
uint8_t
ow_bit_io( uint8_t b )
{ uint8_t sreg;
sreg=SREG;
/*TRY it*///
CLI();
OW_DIR_OUT(); /* drive bus low*/
// delay_us(1); /* Recovery-Time wuffwuff was 1*/
usecsleep(1,1);
//timer1_Delay(1);
if ( b ) OW_DIR_IN(); /* if bit is 1 set bus high (by ext. pull-up)*/
/* wuffwuff delay was 15uS-1 see comment above*/
// delay_us(15-1-OW_CONF_DELAYOFFSET);
usecsleep(1,15-1-OW_CONF_DELAYOFFSET);
//timer1_Delay(15-1-OW_CONF_DELAYOFFSET);
if( OW_GET_IN() == 0 ) b = 0; /* sample at end of read-timeslot*/
// delay_us(60-15);
usecsleep(1,60-15);
//timer1_Delay(60-15);
OW_DIR_IN();
/*TRY it*///SREG=sreg; /* sei();*/
SEI();
return b;
}
inline uint8_t ow_input_pin_state()
{
if (OW_GET_IN()){
return(1);
}
return(0);
}
uint8_t ow_read_bit()
{
cli();
int result;
OW_DIR_OUT(); // drive bus low
_delay_us(6);
OW_DIR_IN();
_delay_us(6); //Recommended values say 9
if( OW_GET_IN() == 0 )
result = 0;
else
result=1; // sample at end of read-timeslot (Reading only possible with high bit)
_delay_us(58); // Complete the time slot and 10us recovery
sei();
return result;
}
/* Timing issue when using runtime-bus-selection (!OW_ONE_BUS):
The master should sample at the end of the 15-slot after initiating
the read-time-slot. The variable bus-settings need more
cycles than the constant ones so the delays had to be shortened
to achive a 15uS overall delay
Setting/clearing a bit in I/O Register needs 1 cyle in OW_ONE_BUS
but around 14 cyles in configureable bus (us-Delay is 4 cyles per uS) */
static uint8_t ow_bit_io_intern( uint8_t b, uint8_t with_parasite_enable )
{
/*ATOMIC_BLOCK(ATOMIC_RESTORESTATE) */{
#if OW_USE_INTERNAL_PULLUP
OW_OUT_LOW();
#endif
OW_DIR_OUT(); // drive bus low
_delay_us(2); // T_INT > 1usec accoding to timing-diagramm
if ( b ) {
OW_DIR_IN(); // to write "1" release bus, resistor pulls high
#if OW_USE_INTERNAL_PULLUP
OW_OUT_HIGH();
#endif
}
// "Output data from the DS18B20 is valid for 15usec after the falling
// edge that initiated the read time slot. Therefore, the master must
// release the bus and then sample the bus state within 15ussec from
// the start of the slot."
_delay_us(15-2-OW_CONF_DELAYOFFSET);
if( OW_GET_IN() == 0 ) {
b = 0; // sample at end of read-timeslot
}
_delay_us(60-15-2+OW_CONF_DELAYOFFSET);
#if OW_USE_INTERNAL_PULLUP
OW_OUT_HIGH();
#endif
OW_DIR_IN();
if ( with_parasite_enable ) {
ow_parasite_enable();
}
} /* ATOMIC_BLOCK */
_delay_us(OW_RECOVERY_TIME); // may be increased for longer wires
return b;
}
uint8_t ow_input_pin_state()
{
return OW_GET_IN();
}
