/*
* \brief Function initialises and registers the RF driver.
*
* \param none
*
* \return rf_radio_driver_id Driver ID given by NET library
*/
static int8_t rf_device_register(void)
{
// If we already exist, bail.
if(radio_state != RADIO_UNINIT) {
return -1;
}
#if MBED_CONF_SL_RAIL_BAND == 2400
RADIO_PA_Init((RADIO_PAInit_t*)&paInit2p4);
#elif (MBED_CONF_SL_RAIL_BAND == 915) || (MBED_CONF_SL_RAIL_BAND == 868)
RADIO_PA_Init((RADIO_PAInit_t*)&paInitSubGhz);
#endif
// Set up PTI since it makes life so much easier
#if defined(DEVICE_SL_PTI)
RADIO_PTIInit_t ptiInit = {
RADIO_PTI_MODE_UART,
1600000,
6,
// TODO: Configure PTI pinout using config system.
// Not very urgent, since all boards use the same pins now.
gpioPortB,
12,
6,
gpioPortB,
11,
6,
gpioPortB,
13,
};
RADIO_PTI_Init(&ptiInit);
#endif
// Set up RAIL
RAIL_RfInit(&railInitParams);
RAIL_ChannelConfig(&channels);
#if MBED_CONF_SL_RAIL_BAND == 2400
RAIL_RadioConfig((void*) ieee802154_config_base);
channel = 11;
#elif (MBED_CONF_SL_RAIL_BAND == 915)
RAIL_RadioConfig((void*) ieee802154_config_915);
channel = 1;
#elif MBED_CONF_SL_RAIL_BAND == 868
RAIL_RadioConfig((void*) ieee802154_config_863);
channel = 0;
#endif
RAIL_IEEE802154_Init((RAIL_IEEE802154_Config_t*)&config);
/* Get real MAC address */
/* MAC is stored MSB first */
memcpy(MAC_address, (const void*)&DEVINFO->UNIQUEH, 4);
memcpy(&MAC_address[4], (const void*)&DEVINFO->UNIQUEL, 4);
/*Set pointer to MAC address*/
device_driver.PHY_MAC = MAC_address;
device_driver.driver_description = (char*)"EFR32_154";
/*Type of RF PHY*/
#if MBED_CONF_SL_RAIL_BAND == 2400
device_driver.link_type = PHY_LINK_15_4_2_4GHZ_TYPE;
#elif (MBED_CONF_SL_RAIL_BAND == 915) || (MBED_CONF_SL_RAIL_BAND == 868)
device_driver.link_type = PHY_LINK_15_4_SUBGHZ_TYPE;
#endif
device_driver.phy_channel_pages = phy_channel_pages;
/*Maximum size of payload is 127*/
device_driver.phy_MTU = 127;
/*1 byte header in PHY layer (length)*/
device_driver.phy_header_length = 1;
/*No tail in PHY layer*/
device_driver.phy_tail_length = 0;
/*Set address write function*/
device_driver.address_write = &rf_address_write;
/*Set RF extension function*/
device_driver.extension = &rf_extension;
/*Set RF state control function*/
device_driver.state_control = &rf_interface_state_control;
/*Set transmit function*/
device_driver.tx = &rf_start_cca;
/*Upper layer callbacks init to NULL, get populated by arm_net_phy_register*/
device_driver.phy_rx_cb = NULL;
device_driver.phy_tx_done_cb = NULL;
/*Virtual upper data callback init to NULL*/
device_driver.arm_net_virtual_rx_cb = NULL;
device_driver.arm_net_virtual_tx_cb = NULL;
/*Register device driver*/
rf_radio_driver_id = arm_net_phy_register(&device_driver);
// If the radio hasn't called the ready callback by now, place it in the initing state
if(radio_state == RADIO_UNINIT) {
radio_state = RADIO_INITING;
}
return rf_radio_driver_id;
}
/*
* \brief Function initialises and registers the RF driver.
*
* \param none
*
* \return rf_radio_driver_id Driver ID given by NET library
*/
static int8_t rf_device_register(void)
{
// If we already exist, bail.
if(radio_state != RADIO_UNINIT) {
return -1;
}
SL_DEBUG_PRINT("rf_device_register: entry\n");
#if MBED_CONF_SL_RAIL_BAND == 2400
RADIO_PA_Init((RADIO_PAInit_t*)&paInit2p4);
#elif (MBED_CONF_SL_RAIL_BAND == 915) || (MBED_CONF_SL_RAIL_BAND == 868)
RADIO_PA_Init((RADIO_PAInit_t*)&paInitSubGhz);
#endif
// Set up PTI since it makes life so much easier
#if defined(MBED_CONF_SL_RAIL_PTI) && (MBED_CONF_SL_RAIL_PTI == 1)
RADIO_PTIInit_t ptiInit = {
MBED_CONF_SL_RAIL_PTI_MODE,
MBED_CONF_SL_RAIL_PTI_BAUDRATE,
MBED_CONF_SL_RAIL_PTI_DOUT_LOCATION,
MBED_CONF_SL_RAIL_PTI_DOUT_PORT,
MBED_CONF_SL_RAIL_PTI_DOUT_PIN,
MBED_CONF_SL_RAIL_PTI_DCLK_LOCATION,
MBED_CONF_SL_RAIL_PTI_DCLK_PORT,
MBED_CONF_SL_RAIL_PTI_DCLK_PIN,
MBED_CONF_SL_RAIL_PTI_DFRAME_LOCATION,
MBED_CONF_SL_RAIL_PTI_DFRAME_PORT,
MBED_CONF_SL_RAIL_PTI_DFRAME_PIN
};
RADIO_PTI_Init(&ptiInit);
#endif
// Set up RAIL
RAIL_RfInit(&railInitParams);
RAIL_ChannelConfig(&channels);
#if (MBED_CONF_SL_RAIL_BAND == 2400)
RAIL_RadioConfig((void*) ieee802154_config_base);
channel = 11;
#elif (MBED_CONF_SL_RAIL_BAND == 915)
RAIL_RadioConfig((void*) ieee802154_config_915);
channel = 1;
#elif (MBED_CONF_SL_RAIL_BAND == 868)
RAIL_RadioConfig((void*) ieee802154_config_863);
channel = 0;
#endif
RAIL_IEEE802154_Init((RAIL_IEEE802154_Config_t*)&config);
/* Get real MAC address */
/* MAC is stored MSB first */
memcpy(MAC_address, (const void*)&DEVINFO->UNIQUEH, 4);
memcpy(&MAC_address[4], (const void*)&DEVINFO->UNIQUEL, 4);
/*Set pointer to MAC address*/
device_driver.PHY_MAC = MAC_address;
device_driver.driver_description = (char*)"EFR32_154";
/*Type of RF PHY*/
#if MBED_CONF_SL_RAIL_BAND == 2400
device_driver.link_type = PHY_LINK_15_4_2_4GHZ_TYPE;
#elif (MBED_CONF_SL_RAIL_BAND == 915) || (MBED_CONF_SL_RAIL_BAND == 868)
device_driver.link_type = PHY_LINK_15_4_SUBGHZ_TYPE;
#endif
device_driver.phy_channel_pages = phy_channel_pages;
/*Maximum size of payload is 127*/
device_driver.phy_MTU = 127;
/*1 byte header in PHY layer (length)*/
device_driver.phy_header_length = 1;
/*No tail in PHY layer*/
device_driver.phy_tail_length = 0;
/*Set address write function*/
device_driver.address_write = &rf_address_write;
/*Set RF extension function*/
device_driver.extension = &rf_extension;
/*Set RF state control function*/
device_driver.state_control = &rf_interface_state_control;
/*Set transmit function*/
device_driver.tx = &rf_start_cca;
/*Upper layer callbacks init to NULL, get populated by arm_net_phy_register*/
device_driver.phy_rx_cb = NULL;
device_driver.phy_tx_done_cb = NULL;
/*Virtual upper data callback init to NULL*/
device_driver.arm_net_virtual_rx_cb = NULL;
device_driver.arm_net_virtual_tx_cb = NULL;
/*Register device driver*/
rf_radio_driver_id = arm_net_phy_register(&device_driver);
// If the radio hasn't called the ready callback by now, place it in the initing state
if(radio_state == RADIO_UNINIT) {
radio_state = RADIO_INITING;
}
#ifdef MBED_CONF_RTOS_PRESENT
rx_queue_head = 0;
rx_queue_tail = 0;
rf_thread_id = osThreadCreate(osThread(rf_thread_loop), NULL);
#endif
return rf_radio_driver_id;
}
/*
* \brief Function initialises and registers the RF driver.
*
* \param none
*
* \return rf_radio_driver_id Driver ID given by NET library
*/
static int8_t rf_device_register(void)
{
// If we already exist, bail.
if(radio_state != RADIO_UNINIT) {
return -1;
}
SL_DEBUG_PRINT("rf_device_register: entry\n");
// Set up RAIL
// Initialize the RAIL library and any internal state it requires
gRailHandle = RAIL_Init(&railCfg, &RAILCb_RfReady);
// Configure calibration settings
RAIL_ConfigCal(gRailHandle, RAIL_CAL_ALL);
// Set up library for IEEE802.15.4 PHY operation
#if (MBED_CONF_SL_RAIL_BAND == 2400)
RAIL_IEEE802154_Config2p4GHzRadio(gRailHandle);
channel = 11;
#elif (MBED_CONF_SL_RAIL_BAND == 915)
RAIL_ConfigChannels(gRailHandle, &channels, NULL);
channel = 1;
#elif (MBED_CONF_SL_RAIL_BAND == 868)
RAIL_ConfigChannels(gRailHandle, &channels, NULL);
channel = 0;
#endif
// Enable 802.15.4 acceleration features
RAIL_IEEE802154_Init(gRailHandle, &config);
// Fire all events by default
RAIL_ConfigEvents(gRailHandle,
RAIL_EVENTS_ALL,
RAIL_EVENTS_ALL);
// Setup the transmit buffer
RAIL_SetTxFifo(gRailHandle, txFifo, 0, sizeof(txFifo));
#if MBED_CONF_SL_RAIL_BAND == 2400
if (RAIL_ConfigTxPower(gRailHandle, &paInit2p4) != RAIL_STATUS_NO_ERROR) {
// Error: The PA could not be initialized due to an improper configuration.
// Please ensure your configuration is valid for the selected part.
while (1) ;
}
#elif (MBED_CONF_SL_RAIL_BAND == 915) || (MBED_CONF_SL_RAIL_BAND == 868)
if (RAIL_ConfigTxPower(gRailHandle, &paInitSubGhz) != RAIL_STATUS_NO_ERROR) {
// Error: The PA could not be initialized due to an improper configuration.
// Please ensure your configuration is valid for the selected part.
while (1) ;
}
#endif
// Set the output power to the maximum supported by this chip
RAIL_SetTxPower(gRailHandle, 255);
// Set up PTI since it makes life so much easier
#if defined(MBED_CONF_SL_RAIL_PTI) && (MBED_CONF_SL_RAIL_PTI == 1)
RAIL_PtiConfig_t ptiConfig = {
MBED_CONF_SL_RAIL_PTI_MODE,
MBED_CONF_SL_RAIL_PTI_BAUDRATE,
MBED_CONF_SL_RAIL_PTI_DOUT_LOCATION,
MBED_CONF_SL_RAIL_PTI_DOUT_PORT,
MBED_CONF_SL_RAIL_PTI_DOUT_PIN,
MBED_CONF_SL_RAIL_PTI_DCLK_LOCATION,
MBED_CONF_SL_RAIL_PTI_DCLK_PORT,
MBED_CONF_SL_RAIL_PTI_DCLK_PIN,
MBED_CONF_SL_RAIL_PTI_DFRAME_LOCATION,
MBED_CONF_SL_RAIL_PTI_DFRAME_PORT,
MBED_CONF_SL_RAIL_PTI_DFRAME_PIN
};
// Initialize the Packet Trace Interface (PTI) for the EFR32
RAIL_ConfigPti(RAIL_EFR32_HANDLE, &ptiConfig);
// Enable Packet Trace (PTI)
RAIL_EnablePti(RAIL_EFR32_HANDLE, true);
#endif
/* Get real MAC address */
/* MAC is stored MSB first */
memcpy(MAC_address, (const void*)&DEVINFO->UNIQUEH, 4);
memcpy(&MAC_address[4], (const void*)&DEVINFO->UNIQUEL, 4);
/*Set pointer to MAC address*/
device_driver.PHY_MAC = MAC_address;
device_driver.driver_description = (char*)"EFR32_154";
/*Type of RF PHY*/
#if MBED_CONF_SL_RAIL_BAND == 2400
device_driver.link_type = PHY_LINK_15_4_2_4GHZ_TYPE;
#elif (MBED_CONF_SL_RAIL_BAND == 915) || (MBED_CONF_SL_RAIL_BAND == 868)
device_driver.link_type = PHY_LINK_15_4_SUBGHZ_TYPE;
#endif
device_driver.phy_channel_pages = phy_channel_pages;
/*Maximum size of payload is 127*/
device_driver.phy_MTU = 127;
/*1 byte header in PHY layer (length)*/
device_driver.phy_header_length = 1;
/*No tail in PHY layer*/
device_driver.phy_tail_length = 0;
/*Set address write function*/
device_driver.address_write = &rf_address_write;
/*Set RF extension function*/
device_driver.extension = &rf_extension;
/*Set RF state control function*/
device_driver.state_control = &rf_interface_state_control;
/*Set transmit function*/
device_driver.tx = &rf_start_cca;
/*Upper layer callbacks init to NULL, get populated by arm_net_phy_register*/
device_driver.phy_rx_cb = NULL;
device_driver.phy_tx_done_cb = NULL;
/*Virtual upper data callback init to NULL*/
device_driver.arm_net_virtual_rx_cb = NULL;
device_driver.arm_net_virtual_tx_cb = NULL;
/*Register device driver*/
rf_radio_driver_id = arm_net_phy_register(&device_driver);
// If the radio hasn't called the ready callback by now, place it in the initing state
if(radio_state == RADIO_UNINIT) {
radio_state = RADIO_INITING;
}
#ifdef MBED_CONF_RTOS_PRESENT
rx_queue_head = 0;
rx_queue_tail = 0;
rf_thread_id = osThreadCreate(osThread(rf_thread_loop), NULL);
#endif
return rf_radio_driver_id;
}
