/*..........................................................................*/
void BSP_init(void) {
/* Enable the floating-point unit */
SCB->CPACR |= (0xFU << 20);
/* Enable lazy stacking for interrupt handlers. This allows FPU
* instructions to be used within interrupt handlers, but at the
* expense of extra stack usage.
*/
ROM_FPULazyStackingEnable();
/* Set the clocking to run directly from the crystal */
ROM_SysCtlClockSet(SYSCTL_SYSDIV_1 | SYSCTL_USE_OSC
| SYSCTL_OSC_MAIN | SYSCTL_XTAL_16MHZ);
/* enable clock to the peripherals used by the application */
SYSCTL->RCGC2 |= (1U << 5); /* enable clock to GPIOF */
__NOP(); /* wait after enabling clocks */
__NOP();
__NOP();
/* configure the LEDs */
GPIOF->DIR |= (LED_RED | LED_GREEN | LED_BLUE);/* set direction: output */
GPIOF->DEN |= (LED_RED | LED_GREEN | LED_BLUE); /* digital enable */
GPIOF->DATA_Bits[LED_RED] = 0U; /* turn the LED off */
GPIOF->DATA_Bits[LED_GREEN] = 0U; /* turn the LED off */
GPIOF->DATA_Bits[LED_BLUE] = 0U; /* turn the LED off */
/* configure the User Switches */
GPIOF->DIR &= ~(USR_SW1 | USR_SW2); /* set direction: input */
ROM_GPIOPadConfigSet(GPIO_PORTF_BASE, (USR_SW1 | USR_SW2),
GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_STD_WPU);
}
void setup() {
ROM_SysCtlClockSet(SYSCTL_SYSDIV_2_5 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN | SYSCTL_XTAL_16MHZ);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOC);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOE);
ROM_FPULazyStackingEnable();
ROM_FPUEnable();
uart_setup();
sd_init();
dac_setup();
keycontrol_setup();
initConfig();
tick_setup();
soundoutcontrol_setup();
setupADC();
setupUSBStore();
initSampleBlocks();
ROM_TimerIntEnable(TIMER0_BASE, TIMER_TIMA_TIMEOUT);
ROM_IntMasterEnable();
DEBUG_PRINT("Setup complete\n", NULL);
}
void init()
{
ROM_FPUEnable();
ROM_FPULazyStackingEnable();
ROM_SysCtlClockSet(SYSCTL_SYSDIV_2_5 | SYSCTL_USE_PLL | SYSCTL_XTAL_16MHZ | SYSCTL_OSC_MAIN);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
GPIO_PORTB_DIR_R = 0x00;
GPIO_PORTB_DEN_R = 0xff;
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
ROM_GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, LED_RED|LED_GREEN|LED_BLUE);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
ROM_GPIOPinConfigure(GPIO_PA0_U0RX);
ROM_GPIOPinConfigure(GPIO_PA1_U0TX);
ROM_GPIOPinTypeUART(GPIO_PORTA_BASE, GPIO_PIN_0 | GPIO_PIN_1);
UARTStdioInit(0);
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / 1000000);
ROM_SysTickEnable();
ROM_SysTickIntEnable();
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER0);
ROM_TimerConfigure(TIMER0_BASE, TIMER_CFG_32_BIT_PER);
reset();
}
//*****************************************************************************
//
// Generic configuration is handled in this function.
//
// This function is called by the start up code to perform any configuration
// necessary before calling the update routine. It is responsible for setting
// the system clock to the expected rate and setting flash programming
// parameters prior to calling ConfigureUSBInterface() to set up the USB
// hardware.
//
// \return None.
//
//*****************************************************************************
void
UpdaterMain(void)
{
//
// Make sure NVIC points at the correct vector table.
//
HWREG(NVIC_VTABLE) = 0;
//
// Run from the PLL at 120 MHz.
//
g_ui32SysClock = MAP_SysCtlClockFreqSet((SYSCTL_XTAL_25MHZ |
SYSCTL_OSC_MAIN |
SYSCTL_USE_PLL |
SYSCTL_CFG_VCO_480), 120000000);
//
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
//
ROM_FPULazyStackingEnable();
//
// Configure the USB interface and power the bus.
//
ConfigureUSBInterface();
//
// Call the updater function. This will attempt to load a new image
// into flash from a USB memory stick.
//
UpdaterUSB();
}
static void sys_setup(void)
{
ROM_FPULazyStackingEnable();
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_XTAL_16MHZ | SYSCTL_OSC_MAIN);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
ROM_GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_2);
}
void Board::init() // initialize the board specifics
{
//
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
//
ROM_FPULazyStackingEnable();
//
// Set the clocking to run from the PLL at 50MHz
//
ROM_SysCtlClockSet(
SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN
| SYSCTL_XTAL_16MHZ);
Usb::init();
/* //
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
FPUEnable();
FPULazyStackingEnable();
SysCtlClockSet(
SYSCTL_SYSDIV_1 | SYSCTL_USE_OSC | SYSCTL_OSC_MAIN
| SYSCTL_XTAL_16MHZ); // Set the clocking to run directly from the crystal.
IntMasterEnable(); // Enable interrupts to the processor.*/
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF); // Enable the GPIO port that is used for the on-board LED.
GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_2); // Enable the GPIO pins for the LED (PF2).
GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_1);
GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_3);
/* SysCtlPeripheralEnable(SYSCTL_PERIPH_UART0); // Enable the peripherals used by this example.
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
IntMasterEnable(); // Enable processor interrupts.
// Set up the period for the SysTick timer for 1 mS.
SysTickPeriodSet(SysCtlClockGet() / 1000);
SysTickIntEnable(); // Enable the SysTick Interrupt.
SysTickEnable(); // Enable SysTick.
GPIOPinConfigure(GPIO_PA0_U0RX); // Set GPIO A0 and A1 as UART pins.
GPIOPinConfigure(GPIO_PA1_U0TX);
GPIOPinTypeUART(GPIO_PORTA_BASE, GPIO_PIN_0 | GPIO_PIN_1);
UARTConfigSetExpClk(UART0_BASE, SysCtlClockGet(), 115200,
(UART_CONFIG_WLEN_8 | UART_CONFIG_STOP_ONE | UART_CONFIG_PAR_NONE)); // Configure the UART for 115,200, 8-N-1 operation.
IntEnable(INT_UART0);
UARTFIFODisable(UART0_BASE);
// UARTFIFOLevelSet(UART0_BASE, UART_FIFO_TX1_8, UART_FIFO_RX1_8);
UARTFlowControlSet(UART0_BASE, UART_FLOWCONTROL_NONE);
UARTIntDisable(UART0_BASE, UART_INT_RT);
UARTIntEnable(UART0_BASE, UART_INT_RX | UART_INT_TX); // Enable the UART interrupt.*/
Board::setLedOn(Board::LED_GREEN, false);
Board::setLedOn(Board::LED_RED, false);
Board::setLedOn(Board::LED_BLUE, false);
ADCInit();
}
void setup()
{
//--------------------- GENERAL ---------------------
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
ROM_FPUEnable();
ROM_FPULazyStackingEnable();
// Set the clocking to run directly from the crystal.
ROM_SysCtlClockSet(SYSCTL_SYSDIV_1 | SYSCTL_USE_OSC | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
ROM_IntMasterEnable();
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
ROM_GPIOPinTypeGPIOOutput(GPIO_PORTA_BASE, GPIO_PIN_6);
//--------------------- UART ---------------------
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_UART0);
GPIOPinConfigure(GPIO_PA0_U0RX);
GPIOPinConfigure(GPIO_PA1_U0TX);
ROM_GPIOPinTypeUART(GPIO_PORTA_BASE, GPIO_PIN_0 | GPIO_PIN_1);
// Configure the UART for 115,200, 8-N-1 operation.
ROM_UARTConfigSetExpClk(UART0_BASE, ROM_SysCtlClockGet(), 115200,
(UART_CONFIG_WLEN_8 | UART_CONFIG_STOP_ONE | UART_CONFIG_PAR_NONE));
// Enable the UART interrupt.
ROM_IntEnable(INT_UART0);
ROM_UARTIntEnable(UART0_BASE, UART_INT_RX | UART_INT_RT);
//--------------------- SSI ---------------------
SysCtlPeripheralEnable(SYSCTL_PERIPH_SSI0);
GPIOPinConfigure(GPIO_PA2_SSI0CLK);
GPIOPinConfigure(GPIO_PA3_SSI0FSS);
GPIOPinConfigure(GPIO_PA4_SSI0RX);
GPIOPinConfigure(GPIO_PA5_SSI0TX);
GPIOPinTypeSSI(GPIO_PORTA_BASE, GPIO_PIN_5 | GPIO_PIN_4 | GPIO_PIN_3 | GPIO_PIN_2);
SSIConfigSetExpClk(SSI0_BASE, SysCtlClockGet(), SSI_FRF_MOTO_MODE_0, SSI_MODE_MASTER, 10000, 8);
SSIEnable(SSI0_BASE);
}
void Config_System(void)
{
ROM_FPUEnable();
ROM_FPULazyStackingEnable();
// Config clock
ROM_SysCtlClockSet(SYSCTL_SYSDIV_2_5 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN | SYSCTL_XTAL_16MHZ);
system_SystickConfig(1);
//
ROM_SysCtlPeripheralEnable(BOOST_ENABLE_PREIPHERAL);
ROM_GPIOPinTypeGPIOOutput(BOOST_ENABLE_PORT, BOOST_ENABLE_PIN);
ROM_GPIOPadConfigSet(BOOST_ENABLE_PORT, BOOST_ENABLE_PIN, GPIO_STRENGTH_8MA, GPIO_PIN_TYPE_STD_WPU);
ROM_GPIOPinWrite(BOOST_ENABLE_PORT, BOOST_ENABLE_PIN, 0xff);
}
// Main ----------------------------------------------------------------------------------------------
int main(void){
// Enable lazy stacking
ROM_FPULazyStackingEnable();
// Set the clocking to run directly from the crystal.
ROM_SysCtlClockSet(SYSCTL_SYSDIV_1 | SYSCTL_USE_OSC | SYSCTL_OSC_MAIN | SYSCTL_XTAL_16MHZ);
// Initialize the UART and write status.
ConfigureUART();
UARTprintf("Timers example\n");
// Enable LEDs
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
ROM_GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, LED_RED|LED_BLUE|LED_GREEN);
// Enable the peripherals used by this example.
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER0);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER1);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER2);
// Enable processor interrupts.
ROM_IntMasterEnable();
// Configure the two 32-bit periodic timers.
ROM_TimerConfigure(TIMER0_BASE, TIMER_CFG_PERIODIC);
ROM_TimerConfigure(TIMER1_BASE, TIMER_CFG_PERIODIC);
ROM_TimerConfigure(TIMER2_BASE, TIMER_CFG_PERIODIC);
ROM_TimerLoadSet(TIMER0_BASE, TIMER_A, ROM_SysCtlClockGet());
ROM_TimerLoadSet(TIMER1_BASE, TIMER_A, ROM_SysCtlClockGet()*2); // Blue should blink 2 times as much as red
ROM_TimerLoadSet(TIMER2_BASE, TIMER_A, ROM_SysCtlClockGet()*3); // Green should blink 3 times as much as red
// Setup the interrupts for the timer timeouts.
ROM_IntEnable(INT_TIMER0A);
ROM_IntEnable(INT_TIMER1A);
ROM_IntEnable(INT_TIMER2A);
ROM_TimerIntEnable(TIMER0_BASE, TIMER_TIMA_TIMEOUT);
ROM_TimerIntEnable(TIMER1_BASE, TIMER_TIMA_TIMEOUT);
ROM_TimerIntEnable(TIMER2_BASE, TIMER_TIMA_TIMEOUT);
// Enable the timers.
ROM_TimerEnable(TIMER0_BASE, TIMER_A);
ROM_TimerEnable(TIMER1_BASE, TIMER_A);
ROM_TimerEnable(TIMER2_BASE, TIMER_A);
// Loop forever while the timers run.
while(1){}
}
static void cpu_init(void) {
g_ulSysTickCount = 0;
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of extra stack usage.
ROM_FPULazyStackingEnable();
// A safety loop in order to interrupt the MCU before setting the clock (wrongly)
int i;
for(i=0; i<1000000; i++);
// Setup for 16MHZ external crystal, use 200MHz PLL and divide by 4 = 50MHz
MAP_SysCtlClockSet(SYSCTL_SYSDIV_16 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
}
// Main ----------------------------------------------------------------------------------------------
int main(void){
// Enable lazy stacking
ROM_FPULazyStackingEnable();
// Set the system clock to run at 40Mhz off PLL with external crystal as reference.
ROM_SysCtlClockSet(SYSCTL_SYSDIV_5 | SYSCTL_USE_PLL | SYSCTL_XTAL_16MHZ | SYSCTL_OSC_MAIN);
// Initialize the UART and write status.
ConfigureUART();
UARTprintf("ISL29023 Example\n");
// Enable LEDs
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
ROM_GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, LED_RED|LED_BLUE|LED_GREEN);
// Enable I2C3
ConfigureI2C3();
// Create struct
tISL29023 islSensHub;
// Create print variables
uint32_t printValue[2];
ISL29023ChangeSettings(ISL29023_COMMANDII_RANGE64k, ISL29023_COMMANDII_RES16, &islSensHub);
while(1){
// Get ALS
ISL29023GetALS(&islSensHub);
FloatToPrint(islSensHub.alsVal, printValue);
UARTprintf("ALS: %d.%03d |.| ",printValue[0],printValue[1]);
// Get IR
ISL29023GetIR(&islSensHub);
FloatToPrint(islSensHub.irVal, printValue);
UARTprintf("IR: %d.%03d\n",printValue[0],printValue[1]);
// Blink LED
ROM_GPIOPinWrite(GPIO_PORTF_BASE, LED_RED|LED_GREEN|LED_BLUE, LED_GREEN);
ROM_SysCtlDelay(ROM_SysCtlClockGet()/3/10); // Delay for 100ms (1/10s) :: ClockGet()/3 = 1second
ROM_GPIOPinWrite(GPIO_PORTF_BASE, LED_RED|LED_GREEN|LED_BLUE, 0);
// Delay for second
ROM_SysCtlDelay(ROM_SysCtlClockGet()/3);
}
}
// Initializes C and starts program
void ResetISR(void)
{
void (**p)() = (void (**)())0x200009ac;
// Set system clock to 80 MHz
ROM_SysCtlClockSet(SYSCTL_SYSDIV_2_5|SYSCTL_USE_PLL|SYSCTL_XTAL_16MHZ|SYSCTL_OSC_MAIN);
// Enable FPU and allow floating point operations in interrupts
ROM_FPUEnable();
ROM_FPULazyStackingEnable();
// Call all the global constructors
(*p)();
main();
}
void initTimer0(int interval, gyro *G){
//
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
//
ROM_FPULazyStackingEnable();
volatile int tick = 0;
tick = (ROM_SysCtlClockGet() / 1000) * interval;
//
// Enable the GPIO port that is used for the on-board LED.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
//
// Enable the GPIO pins for the LED (PF1 & PF2).
//
ROM_GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_2 | GPIO_PIN_1);
//
// Enable the peripherals used by this example.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER0);
//
// Configure the two 32-bit periodic timers.
//
ROM_TimerConfigure(TIMER0_BASE, TIMER_CFG_PERIODIC);
/// imposta il time_out
ROM_TimerLoadSet(TIMER0_BASE, TIMER_A, tick);
G->tick = (float) interval / 1000;
//
// Setup the interrupts for the timer timeouts.
//
ROM_IntEnable(INT_TIMER0A);
//ROM_IntEnable(INT_TIMER1A);
ROM_TimerIntEnable(TIMER0_BASE, TIMER_TIMA_TIMEOUT);
//ROM_TimerIntEnable(TIMER1_BASE, TIMER_TIMA_TIMEOUT);
//
// Enable the timers.
//
ROM_TimerEnable(TIMER0_BASE, TIMER_A);
}
// Main ----------------------------------------------------------------------------------------------
int main(void){
// Enable lazy stacking
ROM_FPULazyStackingEnable();
// Set the clocking to run directly from the crystal.
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4|SYSCTL_USE_PLL|SYSCTL_XTAL_16MHZ|SYSCTL_OSC_MAIN);
// Initialize the UART and write status.
ConfigureUART();
UARTprintf("--Countdown Example--\n");
// Initialize LEDs
ConfigureLEDs();
// Enable the peripherals used by this example.
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER0);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER1);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER2);
// Enable processor interrupts.
ROM_IntMasterEnable();
// Configure the two 32-bit periodic timers.
ROM_TimerConfigure(TIMER0_BASE, TIMER_CFG_PERIODIC);
ROM_TimerConfigure(TIMER1_BASE, TIMER_CFG_PERIODIC);
ROM_TimerConfigure(TIMER2_BASE, TIMER_CFG_ONE_SHOT);
ROM_TimerLoadSet(TIMER0_BASE, TIMER_A, ROM_SysCtlClockGet());
ROM_TimerLoadSet(TIMER1_BASE, TIMER_A, ROM_SysCtlClockGet()/20);
ROM_TimerLoadSet(TIMER2_BASE, TIMER_A, ROM_SysCtlClockGet()/10);
// Setup the interrupts for the timer timeouts.
ROM_IntEnable(INT_TIMER0A);
ROM_IntEnable(INT_TIMER1A);
ROM_IntEnable(INT_TIMER2A);
ROM_TimerIntEnable(TIMER0_BASE, TIMER_TIMA_TIMEOUT);
ROM_TimerIntEnable(TIMER1_BASE, TIMER_TIMA_TIMEOUT);
ROM_TimerIntEnable(TIMER2_BASE, TIMER_TIMA_TIMEOUT);
// Enable the timers.
ROM_TimerEnable(TIMER0_BASE, TIMER_A);
UARTprintf("Time Left: \n");
// Loop forever while the timers run.
while(1){}
}
//*****************************************************************************
// This example demonstrates how to use serial command parser
//*****************************************************************************
int main(void)
{
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
ROM_FPUEnable();
ROM_FPULazyStackingEnable();
// Set the clocking to run directly from the crystal.
ROM_SysCtlClockSet(SYSCTL_SYSDIV_1 | SYSCTL_USE_OSC | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
// Enable the GPIO port that is used for the on-board LED.
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
// Enable the GPIO pins for the LED (PF2).
ROM_GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_2);
// Enable the peripherals used by this example.
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
// configure UART
initUART();
// Enable processor interrupts.
ROM_IntMasterEnable();
// Prompt for text to be entered.
UARTSend((uint8_t *)"\033[2JEnter text: ", 16);
// Loop forever echoing data through the UART.
while(1)
{
//if(RingBufUsed(&g_tBuffRx) > 4)
//{
//for(int i=4; i>0; i--)
//{
//ROM_UARTCharPutNonBlocking(UART0_BASE,RingBufReadOne(&g_tBuffRx));
//}
//}
UARTParse();
}
}
int main(void)
{
//
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
//
ROM_FPULazyStackingEnable();
//
// Setup the system clock to run at 50 Mhz from PLL with crystal reference
//
SysCtlClockSet(SYSCTL_SYSDIV_4|SYSCTL_USE_PLL|SYSCTL_XTAL_16MHZ|
SYSCTL_OSC_MAIN);
//
SetupUART();
SetupI2C();
//
UARTprintf("Starting....\n");
if(!L3G4200D_CheckDevice())
{
UARTprintf("L3G4200D not detected\n");
while(1);
}
SetupL3G4200D();
while(1)
{
short x,y,z;
char buff[20];
L3G4200D_ReadRaw(&x,&y,&z);
ftoa(x,buff);
UARTprintf("X: %s,",buff);
ftoa(y,buff);
UARTprintf("Y: %s,",buff);
ftoa(z,buff);
UARTprintf("Z: %s\n",buff);
DELAY_MS(20);
}
}
/// \brief Initialize the RTOS Kernel for creating objects.
/// \details Enable double-word stack alignment and initialize the Idle thread.
/// \return Status code that indicates the execution status of the function.
/// \note MUST REMAIN UNCHANGED: \b osKernelInitialize shall be consistent in every CMSIS-RTOS.
osStatus osKernelInitialize (void)
{
os_KernelEnterCriticalSection();
// Enable double-word stack alignment
SCB->CCR |= SCB_CCR_STKALIGN_Msk; // Set STKALIGN bit (bit 9) of CCR
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
//
ROM_FPULazyStackingEnable();
os_KernelExitCriticalSection();
// Initialize the Idle thread
// Needs SVC exceptions not masked
if (Init_threadIdle() != 0)
{
stop_cpu;
}
return osOK;
}
//*****************************************************************************
//
// Print "Hello World!" to the display.
//
//*****************************************************************************
int
main(void)
{
tContext sContext;
tRectangle sRect;
//
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
//
ROM_FPULazyStackingEnable();
//
// Set the clocking to run directly from the crystal.
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_XTAL_16MHZ |
SYSCTL_OSC_MAIN);
//
// Initialize the UART.
//
ConfigureUART();
UARTprintf("Hello, world!\n");
//
// Initialize the display driver.
//
CFAL96x64x16Init();
//
// Initialize the graphics context.
//
GrContextInit(&sContext, &g_sCFAL96x64x16);
//
// Fill the top 24 rows of the screen with blue to create the banner.
//
sRect.i16XMin = 0;
sRect.i16YMin = 0;
sRect.i16XMax = GrContextDpyWidthGet(&sContext) - 1;
sRect.i16YMax = 23;
GrContextForegroundSet(&sContext, ClrDarkBlue);
GrRectFill(&sContext, &sRect);
//
// Put a white box around the banner.
//
GrContextForegroundSet(&sContext, ClrWhite);
GrRectDraw(&sContext, &sRect);
//
// Put the application name in the middle of the banner.
//
GrContextFontSet(&sContext, g_psFontCm12);
GrStringDrawCentered(&sContext, "hello", -1,
GrContextDpyWidthGet(&sContext) / 2, 10, 0);
//
// Say hello using the Computer Modern 40 point font.
//
GrContextFontSet(&sContext, g_psFontCm12/*g_psFontFixed6x8*/);
GrStringDrawCentered(&sContext, "Hello World!", -1,
GrContextDpyWidthGet(&sContext) / 2,
((GrContextDpyHeightGet(&sContext) - 24) / 2) + 24,
0);
//
// Flush any cached drawing operations.
//
GrFlush(&sContext);
//
// We are finished. Hang around doing nothing.
//
while(1) {
}
}
//*****************************************************************************
//
// main() -- Execution Starts Here
//
//*****************************************************************************
int main(void)
{
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
ROM_FPULazyStackingEnable ();
// Set the clocking to run directly from the crystal.
SysCtlClockSet(
SYSCTL_SYSDIV_1 | SYSCTL_USE_OSC | SYSCTL_OSC_MAIN
| SYSCTL_XTAL_16MHZ);
// Initialize the I/O Ports (pins)
PortFunctionInit();
// Initialize the UART.
UART_Configure();
// Initialize the I2C3 port as a slave to the cRIO
Slave_Configure();
// Initialize the I2C1 port as master to Gyro
Gyro_Configure();
// Say Hello on debug port
UARTprintf("\nReady.\n");
int16_t i16Data = 0; // holds data read from a gyro register
uint8_t ui8Status = 0; // holds data read from gyro status register
uint32_t ui32Iteration = 0; // iterations counter used to average first N samples
float fAvgDrift = 0.0; // average of 1st N samples, used as an offset to subtract
int16_t i16MaxDrift = 0.0;
int16_t i16MinDrift = 0.0;
float fRate = 0.0; // rate of change in Z in degs/sec
float fAngleDegrees = 0.0; // running Z orientation in degrees
uint16_t ui16AngleScaled = 0.0; // running Z orientation scaled to LSB = 0.01 degrees (i.e. value = degrees * 100)
// Configure the L3G4200D Gyro chip
Gyro_RegWrite(GYRO_CTRL_REG5, 0x80); //BOOT:1 (reboot memory)
SysCtlDelay(SysCtlClockGet() / 200); //delay ~1/200 sec
Gyro_RegWrite(GYRO_CTRL_REG1, 0x0C); //DR:00 (100 Hz) PD:1 (enabled) XYZen:100 (Z only enabled)
SysCtlDelay(SysCtlClockGet() / 200); //delay ~1/200 sec
Gyro_RegWrite(GYRO_CTRL_REG4, 0x10); //FS:01 (500dps)
SysCtlDelay(SysCtlClockGet() / 200); //delay ~1/200 sec
Gyro_RegWrite(GYRO_CTRL_REG5, 0x42); //FIFO_EN:1 (enable FIFO) OUT_SEL:10 (LPF1+LPF2)
SysCtlDelay(SysCtlClockGet() / 200); //delay ~1/200 sec
Gyro_RegWrite(GYRO_FIFO_CTRL_REG, 0x4F); //FM:010 (Stream Mode), WTM:01111
SysCtlDelay(SysCtlClockGet() / 200); //delay ~1/200 sec
//Main Gyro processing loop
while (1)
{
ui8Status = Gyro_RegRead(GYRO_FIFO_SRC_REG);
//UARTprintf("FIFO_SRC_REG: 0x%x\n", ui8Status);
// if Gyro's FIFO is not empty
if (!(ui8Status & 0x20))
{
//report the depth of FIFO:
//if (DEBUG_MODE) UARTprintf("N:0x%02x : ", ui8Status & 0x1F);
// Read X,Y, and Z values.
// NOTE: Found that the FIFo does not empty unless all 3 are read
// TODO: Create a Gyro_RegRead6() to read all 3 values at once
// Cast from unsigned16 to signed16
i16Data = (int16_t) Gyro_RegRead2(GYRO_OUT_X_L); // read and throw away value
i16Data = (int16_t) Gyro_RegRead2(GYRO_OUT_Y_L); // read and throw away value
i16Data = (int16_t) Gyro_RegRead2(GYRO_OUT_Z_L); // read and keep value
//Average the first 100 iterations
if (ui32Iteration < 500)
{
//Note min/max
if (i16Data < i16MinDrift) i16MinDrift = i16Data;
if (i16Data > i16MaxDrift) i16MaxDrift = i16Data;
// compute the running average by taking (average * iteration), which is the sum of all prior iterations,
// adding this iteration's value, and dividing by (iteration+1).
fAvgDrift = ( (fAvgDrift * (float)ui32Iteration) + (float)i16Data ) / (float)(ui32Iteration + 1);
ui32Iteration++;
if (DEBUG_MODE)
{
UARTprintf("Z: %d :", i16Data);
UARTprintf("A: %d :", (int16_t)(fAvgDrift * 100.0));
UARTprintf("m: %d :", i16MinDrift);
UARTprintf("M: %d\n", i16MaxDrift);
}
}
else
{
//remove static drift
fRate = (float)i16Data - fAvgDrift;
//threshold filter (ignore samples below a threshold)
if ( (-THRESHOLD_FILTER < fRate) && (fRate < THRESHOLD_FILTER) )
{
fRate = 0.0;
}
// Convert rate to ( degrees / sec), scale by 1/SAMPLE_RATE_HZ, and sum into degrees
fAngleDegrees += (fRate * GYRO_GAIN / SAMPLE_RATE_HZ) / 2.0;
// wrap angle to be between 0 and 360
//TODO: is there a better way to do this??
while (fAngleDegrees < 0.0) fAngleDegrees += 360.0;
while (fAngleDegrees >= 360.0) fAngleDegrees -= 360.0;
// scale value to LSB = 0.01 degrees (i.e. value = degrees * 100)
ui16AngleScaled = (uint16_t)(fAngleDegrees * 100.0);
// send scaled value out slave i2c port
Slave_SetLatestValue( ui16AngleScaled );
if (DEBUG_MODE)
{
UARTprintf("Z: %d : ", ui16AngleScaled);
UARTprintf("D: %d\n", (int16_t)(fAvgDrift * 100.0));
}
}
LED_DoBlink();
}
}
}
//*****************************************************************************
//
// This is the main application entry function.
//
//*****************************************************************************
int
main(void)
{
uint32_t ui32TxCount;
uint32_t ui32RxCount;
//uint32_t ui32Loop;
//
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
//
ROM_FPULazyStackingEnable();
//
// Set the clocking to run from the PLL at 50MHz
//
#if 1
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// Configure the required pins for USB operation.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
ROM_GPIOPinTypeUSBAnalog(GPIO_PORTD_BASE, GPIO_PIN_5 | GPIO_PIN_4);
//ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / 100);
/* This code taken from: http://e2e.ti.com/support/microcontrollers/tiva_arm/f/908/t/311237.aspx
*/
#else
#include "hw_nvic.h"
FlashErase(0x00000000);
ROM_IntMasterDisable();
ROM_SysTickIntDisable();
ROM_SysTickDisable();
uint32_t ui32SysClock;
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN | SYSCTL_XTAL_16MHZ);
ui32SysClock = ROM_SysCtlClockGet();
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
ROM_GPIOPinTypeUSBAnalog(GPIO_PORTD_BASE, GPIO_PIN_4 | GPIO_PIN_5);
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / 100);
HWREG(NVIC_DIS0) = 0xffffffff;
HWREG(NVIC_DIS1) = 0xffffffff;
HWREG(NVIC_DIS2) = 0xffffffff;
HWREG(NVIC_DIS3) = 0xffffffff;
HWREG(NVIC_DIS4) = 0xffffffff;
int ui32Addr;
for(ui32Addr = NVIC_PRI0; ui32Addr <= NVIC_PRI34; ui32Addr+=4)
{
HWREG(ui32Addr) = 0;
}
HWREG(NVIC_SYS_PRI1) = 0;
HWREG(NVIC_SYS_PRI2) = 0;
HWREG(NVIC_SYS_PRI3) = 0;
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_USB0);
ROM_SysCtlPeripheralReset(SYSCTL_PERIPH_USB0);
ROM_SysCtlUSBPLLEnable();
ROM_SysCtlDelay(ui32SysClock*2 / 3);
ROM_IntMasterEnable();
ROM_UpdateUSB(0);
while(1)
{
}
#endif
#define BOOTLOADER_TEST 0
#if BOOTLOADER_TEST
#include "hw_nvic.h"
//ROM_UpdateUART();
// May need to do the following here:
// 0. See if this will cause bootloader to start
//ROM_FlashErase(0);
//ROM_UpdateUSB(0);
#define SYSTICKS_PER_SECOND 100
uint32_t ui32SysClock = ROM_SysCtlClockGet();
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / SYSTICKS_PER_SECOND);
ROM_SysTickIntEnable();
ROM_SysTickEnable();
//USBDCDTerm(0);
// Disable all interrupts
ROM_IntMasterDisable();
ROM_SysTickIntDisable();
ROM_SysTickDisable();
HWREG(NVIC_DIS0) = 0xffffffff;
HWREG(NVIC_DIS1) = 0xffffffff;
HWREG(NVIC_DIS2) = 0xffffffff;
HWREG(NVIC_DIS3) = 0xffffffff;
HWREG(NVIC_DIS4) = 0xffffffff;
int ui32Addr;
for(ui32Addr = NVIC_PRI0; ui32Addr <= NVIC_PRI34; ui32Addr+=4)
{
HWREG(ui32Addr) = 0;
}
HWREG(NVIC_SYS_PRI1) = 0;
HWREG(NVIC_SYS_PRI2) = 0;
HWREG(NVIC_SYS_PRI3) = 0;
// 1. Enable USB PLL
//ROM_SysCtlUSBPLLEnable();
// 2. Enable USB controller
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_USB0);
ROM_SysCtlPeripheralReset(SYSCTL_PERIPH_USB0);
//USBClockEnable(USB0_BASE, 8, USB_CLOCK_INTERNAL);
//HWREG(USB0_BASE + USB_O_CC) = (8 - 1) | USB_CLOCK_INTERNAL;
ROM_SysCtlUSBPLLEnable();
// 3. Enable USB D+ D- pins
// 4. Activate USB DFU
ROM_SysCtlDelay(ui32SysClock * 2 / 3);
ROM_IntMasterEnable(); // Re-enable interrupts at NVIC level
ROM_UpdateUSB(0);
// 5. Should never get here since update is in progress
#endif // BOOTLOADER_TEST
//
// Enable the GPIO port that is used for the on-board LED.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB); // gjs Our board uses GPIOB for LEDs
// gjs original ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
//
// Enable the GPIO pins for the LED (PF2 & PF3).
//
ROM_GPIOPinTypeGPIOOutput(GPIO_PORTB_BASE, GPIO_PIN_0|GPIO_PIN_1);
// gjs original ROM_GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_3|GPIO_PIN_2);
//
// Not configured initially.
//
g_bUSBConfigured = false;
//
// Enable the UART that we will be redirecting.
//
ROM_SysCtlPeripheralEnable(USB_UART_PERIPH);
//
// Enable and configure the UART RX and TX pins
//
ROM_SysCtlPeripheralEnable(TX_GPIO_PERIPH);
ROM_SysCtlPeripheralEnable(RX_GPIO_PERIPH);
ROM_GPIOPinTypeUART(TX_GPIO_BASE, TX_GPIO_PIN);
ROM_GPIOPinTypeUART(RX_GPIO_BASE, RX_GPIO_PIN);
//
// TODO: Add code to configure handshake GPIOs if required.
//
//
// Set the default UART configuration.
//
ROM_UARTConfigSetExpClk(USB_UART_BASE, ROM_SysCtlClockGet(),
DEFAULT_BIT_RATE, DEFAULT_UART_CONFIG);
ROM_UARTFIFOLevelSet(USB_UART_BASE, UART_FIFO_TX4_8, UART_FIFO_RX4_8);
//
// Configure and enable UART interrupts.
//
ROM_UARTIntClear(USB_UART_BASE, ROM_UARTIntStatus(USB_UART_BASE, false));
ROM_UARTIntEnable(USB_UART_BASE, (UART_INT_OE | UART_INT_BE | UART_INT_PE |
UART_INT_FE | UART_INT_RT | UART_INT_TX | UART_INT_RX));
//
// Enable the system tick.
//
#if 0
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / SYSTICKS_PER_SECOND);
ROM_SysTickIntEnable();
ROM_SysTickEnable();
#endif
//
// Initialize the transmit and receive buffers.
//
USBBufferInit(&g_sTxBuffer);
USBBufferInit(&g_sRxBuffer);
//
// Set the USB stack mode to Device mode with VBUS monitoring.
//
USBStackModeSet(0, eUSBModeDevice, 0);
//
// Pass our device information to the USB library and place the device
// on the bus.
//
USBDCDCInit(0, &g_sCDCDevice);
//
// Clear our local byte counters.
//
ui32RxCount = 0;
ui32TxCount = 0;
//
// Enable interrupts now that the application is ready to start.
//
ROM_IntEnable(USB_UART_INT);
// Enable FreeRTOS
mainA(); // FreeRTOS. Will not return
#if 0
//
// Main application loop.
//
while(1)
{
//
// Have we been asked to update the status display?
//
if(g_ui32Flags & COMMAND_STATUS_UPDATE)
{
//
// Clear the command flag
//
ROM_IntMasterDisable();
g_ui32Flags &= ~COMMAND_STATUS_UPDATE;
ROM_IntMasterEnable();
}
//
// Has there been any transmit traffic since we last checked?
//
if(ui32TxCount != g_ui32UARTTxCount)
{
//
// Turn on the Green LED.
//
// gjs ROM_UARTCharPutNonBlocking(USB_UART_BASE, 'b');
#if 1
if (ui32TxCount & 1) {
GPIOPinWrite(GPIO_PORTB_BASE, GPIO_PIN_0, GPIO_PIN_0);
} else {
GPIOPinWrite(GPIO_PORTB_BASE, GPIO_PIN_0, 0);
}
#else
if (1 || g_ui32UARTTxCount & 0x01) {
GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_3, GPIO_PIN_3);
} else {
//GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_3, 0);
}
//
// Delay for a bit.
//
for(uint32_t ui32Loop = 0; ui32Loop < 150000; ui32Loop++)
{
}
//
// Turn off the Green LED.
//
GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_3, 0);
#endif
//
// Take a snapshot of the latest transmit count.
//
ui32TxCount = g_ui32UARTTxCount;
}
//
// Has there been any receive traffic since we last checked?
//
if(ui32RxCount != g_ui32UARTRxCount)
{
//
// Turn on the Blue LED.
//
#if 1
if (ui32RxCount & 1) {
GPIOPinWrite(GPIO_PORTB_BASE, GPIO_PIN_1, GPIO_PIN_1);
} else {
GPIOPinWrite(GPIO_PORTB_BASE, GPIO_PIN_1, 0);
}
#else
GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_2, GPIO_PIN_2);
//
// Delay for a bit.
//
for(uint32_t ui32Loop = 0; ui32Loop < 150000; ui32Loop++)
{
}
//
// Turn off the Blue LED.
//
GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_2, 0);
#endif
//
// Take a snapshot of the latest receive count.
//
ui32RxCount = g_ui32UARTRxCount;
}
}
#endif
}
//*****************************************************************************
//
// This is the main example program. It checks to see that the interrupts are
// processed in the correct order when they have identical priorities,
// increasing priorities, and decreasing priorities. This exercises interrupt
// preemption and tail chaining.
//
//*****************************************************************************
int
main(void)
{
uint32_t ui32Error;
//
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
//
ROM_FPULazyStackingEnable();
//
// Set the clocking to run directly from the crystal.
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_1 | SYSCTL_USE_OSC | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// Enable the peripherals used by this example.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOE);
//
// Initialize the UART.
//
ConfigureUART();
UARTprintf("\033[2JInterrupts\n");
//
// Configure the PB0-PB2 to be outputs to indicate entry/exit of one
// of the interrupt handlers.
//
ROM_GPIOPinTypeGPIOOutput(GPIO_PORTE_BASE, GPIO_PIN_1 | GPIO_PIN_2 |
GPIO_PIN_3);
ROM_GPIOPinWrite(GPIO_PORTE_BASE, GPIO_PIN_1 | GPIO_PIN_2 | GPIO_PIN_3, 0);
//
// Set up and enable the SysTick timer. It will be used as a reference
// for delay loops in the interrupt handlers. The SysTick timer period
// will be set up for one second.
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet());
ROM_SysTickEnable();
//
// Reset the error indicator.
//
ui32Error = 0;
//
// Enable interrupts to the processor.
//
ROM_IntMasterEnable();
//
// Enable the interrupts.
//
ROM_IntEnable(INT_GPIOA);
ROM_IntEnable(INT_GPIOB);
ROM_IntEnable(INT_GPIOC);
//
// Indicate that the equal interrupt priority test is beginning.
//
UARTprintf("\nEqual Priority\n");
//
// Set the interrupt priorities so they are all equal.
//
ROM_IntPrioritySet(INT_GPIOA, 0x00);
ROM_IntPrioritySet(INT_GPIOB, 0x00);
ROM_IntPrioritySet(INT_GPIOC, 0x00);
//
// Reset the interrupt flags.
//
g_ui32GPIOa = 0;
g_ui32GPIOb = 0;
g_ui32GPIOc = 0;
g_ui32Index = 1;
//
// Trigger the interrupt for GPIO C.
//
HWREG(NVIC_SW_TRIG) = INT_GPIOC - 16;
//
// Put the current interrupt state on the LCD.
//
DisplayIntStatus();
//
// Verify that the interrupts were processed in the correct order.
//
if((g_ui32GPIOa != 3) || (g_ui32GPIOb != 2) || (g_ui32GPIOc != 1))
{
ui32Error |= 1;
}
//
// Wait two seconds.
//
Delay(2);
//
// Indicate that the decreasing interrupt priority test is beginning.
//
UARTprintf("\nDecreasing Priority\n");
//
// Set the interrupt priorities so that they are decreasing (i.e. C > B >
// A).
//
ROM_IntPrioritySet(INT_GPIOA, 0x80);
ROM_IntPrioritySet(INT_GPIOB, 0x40);
ROM_IntPrioritySet(INT_GPIOC, 0x00);
//
// Reset the interrupt flags.
//
g_ui32GPIOa = 0;
g_ui32GPIOb = 0;
g_ui32GPIOc = 0;
g_ui32Index = 1;
//
// Trigger the interrupt for GPIO C.
//
HWREG(NVIC_SW_TRIG) = INT_GPIOC - 16;
//
// Put the current interrupt state on the UART.
//
DisplayIntStatus();
//
// Verify that the interrupts were processed in the correct order.
//
if((g_ui32GPIOa != 3) || (g_ui32GPIOb != 2) || (g_ui32GPIOc != 1))
{
ui32Error |= 2;
}
//
// Wait two seconds.
//
Delay(2);
//
// Indicate that the increasing interrupt priority test is beginning.
//
UARTprintf("\nIncreasing Priority\n");
//
// Set the interrupt priorities so that they are increasing (i.e. C < B <
// A).
//
ROM_IntPrioritySet(INT_GPIOA, 0x00);
ROM_IntPrioritySet(INT_GPIOB, 0x40);
ROM_IntPrioritySet(INT_GPIOC, 0x80);
//
// Reset the interrupt flags.
//
g_ui32GPIOa = 0;
g_ui32GPIOb = 0;
g_ui32GPIOc = 0;
g_ui32Index = 1;
//
// Trigger the interrupt for GPIO C.
//
HWREG(NVIC_SW_TRIG) = INT_GPIOC - 16;
//
// Put the current interrupt state on the UART.
//
DisplayIntStatus();
//
// Verify that the interrupts were processed in the correct order.
//
if((g_ui32GPIOa != 1) || (g_ui32GPIOb != 2) || (g_ui32GPIOc != 3))
{
ui32Error |= 4;
}
//
// Wait two seconds.
//
Delay(2);
//
// Disable the interrupts.
//
ROM_IntDisable(INT_GPIOA);
ROM_IntDisable(INT_GPIOB);
ROM_IntDisable(INT_GPIOC);
//
// Disable interrupts to the processor.
//
ROM_IntMasterDisable();
//
// Print out the test results.
//
UARTprintf("\nInterrupt Priority =: %s >: %s <: %s\n",
(ui32Error & 1) ? "Fail" : "Pass",
(ui32Error & 2) ? "Fail" : "Pass",
(ui32Error & 4) ? "Fail" : "Pass");
//
// Loop forever.
//
while(1)
{
}
}
//*****************************************************************************
//
// Demonstrate the use of the USB stick update example.
//
//*****************************************************************************
int
main(void)
{
unsigned long ulCount;
tContext sContext;
tRectangle sRect;
//
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
//
ROM_FPULazyStackingEnable();
//
// Set the system clock to run at 50MHz from the PLL.
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// Initialize the display driver.
//
CFAL96x64x16Init();
//
// Initialize the graphics context.
//
GrContextInit(&sContext, &g_sCFAL96x64x16);
//
// Fill the top 24 rows of the screen with blue to create the banner.
//
sRect.sXMin = 0;
sRect.sYMin = 0;
sRect.sXMax = GrContextDpyWidthGet(&sContext) - 1;
sRect.sYMax = 9;
GrContextForegroundSet(&sContext, ClrDarkBlue);
GrRectFill(&sContext, &sRect);
//
// Put a white box around the banner.
//
GrContextForegroundSet(&sContext, ClrWhite);
GrRectDraw(&sContext, &sRect);
//
// Put the application name in the middle of the banner.
//
GrContextFontSet(&sContext, g_pFontFixed6x8);
GrStringDrawCentered(&sContext, "usb-stick-demo", -1,
GrContextDpyWidthGet(&sContext) / 2, 4, 0);
//
// Indicate what is happening.
//
GrStringDrawCentered(&sContext, "Press the", -1,
GrContextDpyWidthGet(&sContext) / 2, 20, 0);
GrStringDrawCentered(&sContext, "select button to", -1,
GrContextDpyWidthGet(&sContext) / 2, 30, 0);
GrStringDrawCentered(&sContext, "start the USB", -1,
GrContextDpyWidthGet(&sContext) / 2, 40, 0);
GrStringDrawCentered(&sContext, "stick updater.", -1,
GrContextDpyWidthGet(&sContext) / 2, 50, 0);
//
// Flush any cached drawing operations.
//
GrFlush(&sContext);
//
// Enable the GPIO module which the select button is attached to.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOM);
//
// Enable the GPIO pin to read the user button.
//
ROM_GPIODirModeSet(GPIO_PORTM_BASE, GPIO_PIN_4, GPIO_DIR_MODE_IN);
ROM_GPIOPadConfigSet(GPIO_PORTM_BASE, GPIO_PIN_4, GPIO_STRENGTH_2MA,
GPIO_PIN_TYPE_STD_WPU);
//
// Wait for the pullup to take effect or the next loop will exist too soon.
//
SysCtlDelay(1000);
//
// Wait until the select button has been pressed for ~40ms (in order to
// debounce the press).
//
ulCount = 0;
while(1)
{
//
// See if the button is pressed.
//
if(ROM_GPIOPinRead(GPIO_PORTM_BASE, GPIO_PIN_4) == 0)
{
//
// Increment the count since the button is pressed.
//
ulCount++;
//
// If the count has reached 4, then the button has been debounced
// as being pressed.
//
if(ulCount == 4)
{
break;
}
}
else
{
//
// Reset the count since the button is not pressed.
//
ulCount = 0;
}
//
// Delay for approximately 10ms.
//
SysCtlDelay(16000000 / (3 * 100));
}
//
// Wait until the select button has been released for ~40ms (in order to
// debounce the release).
//
ulCount = 0;
while(1)
{
//
// See if the button is pressed.
//
if(ROM_GPIOPinRead(GPIO_PORTM_BASE, GPIO_PIN_4) != 0)
{
//
// Increment the count since the button is released.
//
ulCount++;
//
// If the count has reached 4, then the button has been debounced
// as being released.
//
if(ulCount == 4)
{
break;
}
}
else
{
//
// Reset the count since the button is pressed.
//
ulCount = 0;
}
//
// Delay for approximately 10ms.
//
SysCtlDelay(16000000 / (3 * 100));
}
//
// Indicate that the updater is being called.
//
GrStringDrawCentered(&sContext, "The USB stick", -1,
GrContextDpyWidthGet(&sContext) / 2, 20, true);
GrStringDrawCentered(&sContext, "updater is now", -1,
GrContextDpyWidthGet(&sContext) / 2, 30, true);
GrStringDrawCentered(&sContext, "waiting for a", -1,
GrContextDpyWidthGet(&sContext) / 2, 40, true);
GrStringDrawCentered(&sContext, "USB stick.", -1,
GrContextDpyWidthGet(&sContext) / 2, 50, true);
//
// Flush any cached drawing operations.
//
GrFlush(&sContext);
//
// Call the updater so that it will search for an update on a memory stick.
//
(*((void (*)(void))(*(unsigned long *)0x2c)))();
//
// The updater should take control, so this should never be reached.
// Just in case, loop forever.
//
while(1)
{
}
}
//*****************************************************************************
//
// This is the main application entry function.
//
//*****************************************************************************
int
main(void)
{
uint32_t ui32TxCount;
uint32_t ui32RxCount;
tRectangle sRect;
char pcBuffer[16];
uint32_t ui32Fullness;
//
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
//
ROM_FPULazyStackingEnable();
//
// Set the clocking to run from the PLL at 50MHz
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// Configure the required pins for USB operation.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOG);
ROM_GPIOPinConfigure(GPIO_PG4_USB0EPEN);
ROM_GPIOPinTypeUSBDigital(GPIO_PORTG_BASE, GPIO_PIN_4);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOL);
ROM_GPIOPinTypeUSBAnalog(GPIO_PORTL_BASE, GPIO_PIN_6 | GPIO_PIN_7);
ROM_GPIOPinTypeUSBAnalog(GPIO_PORTB_BASE, GPIO_PIN_0 | GPIO_PIN_1);
//
// Erratum workaround for silicon revision A1. VBUS must have pull-down.
//
if(CLASS_IS_BLIZZARD && REVISION_IS_A1)
{
HWREG(GPIO_PORTB_BASE + GPIO_O_PDR) |= GPIO_PIN_1;
}
//
// Not configured initially.
//
g_bUSBConfigured = false;
//
// Initialize the display driver.
//
CFAL96x64x16Init();
//
// Initialize the graphics context.
//
GrContextInit(&g_sContext, &g_sCFAL96x64x16);
//
// Fill the top 15 rows of the screen with blue to create the banner.
//
sRect.i16XMin = 0;
sRect.i16YMin = 0;
sRect.i16XMax = GrContextDpyWidthGet(&g_sContext) - 1;
sRect.i16YMax = 9;
GrContextForegroundSet(&g_sContext, ClrDarkBlue);
GrRectFill(&g_sContext, &sRect);
//
// Put a white box around the banner.
//
GrContextForegroundSet(&g_sContext, ClrWhite);
GrRectDraw(&g_sContext, &sRect);
//
// Put the application name in the middle of the banner.
//
GrContextFontSet(&g_sContext, g_psFontFixed6x8);
GrStringDrawCentered(&g_sContext, "usb-dev-serial", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 4, 0);
//
// Show the various static text elements on the color STN display.
//
GrStringDraw(&g_sContext, "Tx #",-1, 0, 12, false);
GrStringDraw(&g_sContext, "Tx buf", -1, 0, 22, false);
GrStringDraw(&g_sContext, "Rx #", -1, 0, 32, false);
GrStringDraw(&g_sContext, "Rx buf", -1, 0, 42, false);
DrawBufferMeter(&g_sContext, 40, 22);
DrawBufferMeter(&g_sContext, 40, 42);
//
// Enable the UART that we will be redirecting.
//
ROM_SysCtlPeripheralEnable(USB_UART_PERIPH);
//
// Enable and configure the UART RX and TX pins
//
ROM_SysCtlPeripheralEnable(TX_GPIO_PERIPH);
ROM_SysCtlPeripheralEnable(RX_GPIO_PERIPH);
ROM_GPIOPinTypeUART(TX_GPIO_BASE, TX_GPIO_PIN);
ROM_GPIOPinTypeUART(RX_GPIO_BASE, RX_GPIO_PIN);
//
// TODO: Add code to configure handshake GPIOs if required.
//
//
// Set the default UART configuration.
//
ROM_UARTConfigSetExpClk(USB_UART_BASE, ROM_SysCtlClockGet(),
DEFAULT_BIT_RATE, DEFAULT_UART_CONFIG);
ROM_UARTFIFOLevelSet(USB_UART_BASE, UART_FIFO_TX4_8, UART_FIFO_RX4_8);
//
// Configure and enable UART interrupts.
//
ROM_UARTIntClear(USB_UART_BASE, ROM_UARTIntStatus(USB_UART_BASE, false));
ROM_UARTIntEnable(USB_UART_BASE, (UART_INT_OE | UART_INT_BE | UART_INT_PE |
UART_INT_FE | UART_INT_RT | UART_INT_TX | UART_INT_RX));
//
// Enable the system tick.
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / SYSTICKS_PER_SECOND);
ROM_SysTickIntEnable();
ROM_SysTickEnable();
//
// Tell the user what we are up to.
//
DisplayStatus(&g_sContext, " Configuring... ");
//
// Initialize the transmit and receive buffers.
//
USBBufferInit(&g_sTxBuffer);
USBBufferInit(&g_sRxBuffer);
//
// Set the USB stack mode to Device mode with VBUS monitoring.
//
USBStackModeSet(0, eUSBModeDevice, 0);
//
// Pass our device information to the USB library and place the device
// on the bus.
//
USBDCDCInit(0, &g_sCDCDevice);
//
// Wait for initial configuration to complete.
//
DisplayStatus(&g_sContext, "Waiting for host");
//
// Clear our local byte counters.
//
ui32RxCount = 0;
ui32TxCount = 0;
//
// Enable interrupts now that the application is ready to start.
//
ROM_IntEnable(USB_UART_INT);
//
// Main application loop.
//
while(1)
{
//
// Have we been asked to update the status display?
//
if(g_ui32Flags & COMMAND_STATUS_UPDATE)
{
//
// Clear the command flag
//
ROM_IntMasterDisable();
g_ui32Flags &= ~COMMAND_STATUS_UPDATE;
ROM_IntMasterEnable();
DisplayStatus(&g_sContext, g_pcStatus);
}
//
// Has there been any transmit traffic since we last checked?
//
if(ui32TxCount != g_ui32UARTTxCount)
{
//
// Take a snapshot of the latest transmit count.
//
ui32TxCount = g_ui32UARTTxCount;
//
// Update the display of bytes transmitted by the UART.
//
usnprintf(pcBuffer, 16, "%d ", ui32TxCount);
GrStringDraw(&g_sContext, pcBuffer, -1, 40, 12, true);
//
// Update the RX buffer fullness. Remember that the buffers are
// named relative to the USB whereas the status display is from
// the UART's perspective. The USB's receive buffer is the UART's
// transmit buffer.
//
ui32Fullness = ((USBBufferDataAvailable(&g_sRxBuffer) * 100) /
UART_BUFFER_SIZE);
UpdateBufferMeter(&g_sContext, ui32Fullness, 40, 22);
}
//
// Has there been any receive traffic since we last checked?
//
if(ui32RxCount != g_ui32UARTRxCount)
{
//
// Take a snapshot of the latest receive count.
//
ui32RxCount = g_ui32UARTRxCount;
//
// Update the display of bytes received by the UART.
//
usnprintf(pcBuffer, 16, "%d ", ui32RxCount);
GrStringDraw(&g_sContext, pcBuffer, -1, 40, 32, true);
//
// Update the TX buffer fullness. Remember that the buffers are
// named relative to the USB whereas the status display is from
// the UART's perspective. The USB's transmit buffer is the UART's
// receive buffer.
//
ui32Fullness = ((USBBufferDataAvailable(&g_sTxBuffer) * 100) /
UART_BUFFER_SIZE);
UpdateBufferMeter(&g_sContext, ui32Fullness, 40, 42);
}
}
}
//*****************************************************************************
//
// This is the main application entry function.
//
//*****************************************************************************
int
main(void)
{
uint_fast32_t ui32TxCount;
uint_fast32_t ui32RxCount;
tRectangle sRect;
char pcBuffer[16];
//
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
//
ROM_FPULazyStackingEnable();
//
// Set the clocking to run from the PLL at 50MHz
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
#ifdef DEBUG
//
// Configure the UART for debug output.
//
ConfigureUART();
#endif
//
// Not configured initially.
//
g_bUSBConfigured = false;
//
// Initialize the display driver.
//
CFAL96x64x16Init();
//
// Initialize the graphics context.
//
GrContextInit(&g_sContext, &g_sCFAL96x64x16);
//
// Fill the top part of the screen with blue to create the banner.
//
sRect.i16XMin = 0;
sRect.i16YMin = 0;
sRect.i16XMax = GrContextDpyWidthGet(&g_sContext) - 1;
sRect.i16YMax = 9;
GrContextForegroundSet(&g_sContext, ClrDarkBlue);
GrRectFill(&g_sContext, &sRect);
//
// Change foreground for white text.
//
GrContextForegroundSet(&g_sContext, ClrWhite);
//
// Put the application name in the middle of the banner.
//
GrContextFontSet(&g_sContext, g_psFontFixed6x8);
GrStringDrawCentered(&g_sContext, "usb-dev-bulk", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 4, 0);
//
// Show the various static text elements on the color STN display.
//
GrStringDraw(&g_sContext, "Tx bytes:", -1, 0, 32, false);
GrStringDraw(&g_sContext, "Rx bytes:", -1, 0, 42, false);
//
// Enable the GPIO peripheral used for USB, and configure the USB
// pins.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOL);
ROM_GPIOPinTypeUSBAnalog(GPIO_PORTB_BASE, GPIO_PIN_0 | GPIO_PIN_1);
ROM_GPIOPinTypeUSBAnalog(GPIO_PORTL_BASE, GPIO_PIN_6 | GPIO_PIN_7);
//
// Enable the system tick.
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / SYSTICKS_PER_SECOND);
ROM_SysTickIntEnable();
ROM_SysTickEnable();
//
// Show the application name on the display and UART output.
//
DEBUG_PRINT("\nTiva C Series USB bulk device example\n");
DEBUG_PRINT("---------------------------------\n\n");
//
// Tell the user what we are up to.
//
DisplayStatus(&g_sContext, "Configuring USB");
//
// Initialize the transmit and receive buffers.
//
USBBufferInit(&g_sTxBuffer);
USBBufferInit(&g_sRxBuffer);
//
// Pass our device information to the USB library and place the device
// on the bus.
//
USBDBulkInit(0, &g_sBulkDevice);
//
// Wait for initial configuration to complete.
//
DisplayStatus(&g_sContext, "Waiting for host");
//
// Clear our local byte counters.
//
ui32RxCount = 0;
ui32TxCount = 0;
//
// Main application loop.
//
while(1)
{
//
// Have we been asked to update the status display?
//
if(g_ui32Flags & COMMAND_STATUS_UPDATE)
{
//
// Clear the command flag
//
g_ui32Flags &= ~COMMAND_STATUS_UPDATE;
DisplayStatus(&g_sContext, g_pcStatus);
}
//
// Has there been any transmit traffic since we last checked?
//
if(ui32TxCount != g_ui32TxCount)
{
//
// Take a snapshot of the latest transmit count.
//
ui32TxCount = g_ui32TxCount;
//
// Update the display of bytes transmitted by the UART.
//
usnprintf(pcBuffer, 16, " %d ", ui32TxCount);
GrStringDraw(&g_sContext, pcBuffer, -1, 48, 32, true);
}
//
// Has there been any receive traffic since we last checked?
//
if(ui32RxCount != g_ui32RxCount)
{
//
// Take a snapshot of the latest receive count.
//
ui32RxCount = g_ui32RxCount;
//
// Update the display of bytes received by the UART.
//
usnprintf(pcBuffer, 16, " %d ", ui32RxCount);
GrStringDraw(&g_sContext, pcBuffer, -1, 48, 42, true);
}
}
}
//*****************************************************************************
//
// This is the main loop that runs the application.
//
//*****************************************************************************
int
main(void)
{
tRectangle sRect;
tUSBMode eLastMode;
char *pcString;
//
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
//
ROM_FPULazyStackingEnable();
//
// Set the system clock to run at 50MHz from the PLL.
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// Initially wait for device connection.
//
g_eUSBState = STATE_NO_DEVICE;
eLastMode = USB_MODE_OTG;
g_eCurrentUSBMode = USB_MODE_OTG;
//
// Enable Clocking to the USB controller.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_USB0);
//
// Configure the required pins for USB operation.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOG);
ROM_GPIOPinConfigure(GPIO_PG4_USB0EPEN);
ROM_GPIOPinTypeUSBDigital(GPIO_PORTG_BASE, GPIO_PIN_4);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOL);
ROM_GPIOPinTypeUSBAnalog(GPIO_PORTL_BASE, GPIO_PIN_6 | GPIO_PIN_7);
ROM_GPIOPinTypeUSBAnalog(GPIO_PORTB_BASE, GPIO_PIN_0 | GPIO_PIN_1);
//
// Configure SysTick for a 100Hz interrupt.
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / TICKS_PER_SECOND);
ROM_SysTickEnable();
ROM_SysTickIntEnable();
//
// Enable Interrupts
//
ROM_IntMasterEnable();
//
// Enable clocking to the UART and associated GPIO
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_UART0);
//
// Configure the relevant pins such that UART0 owns them.
//
ROM_GPIOPinTypeUART(GPIO_PORTA_BASE, GPIO_PIN_0 | GPIO_PIN_1);
//
// Open UART0 for debug output.
//
UARTStdioInit(0);
//
// Initialize the USB stack mode and pass in a mode callback.
//
USBStackModeSet(0, USB_MODE_OTG, ModeCallback);
//
// Register the host class drivers.
//
USBHCDRegisterDrivers(0, g_ppHostClassDrivers, g_ulNumHostClassDrivers);
//
// Open an instance of the keyboard driver. The keyboard does not need
// to be present at this time, this just save a place for it and allows
// the applications to be notified when a keyboard is present.
//
g_ulKeyboardInstance = USBHKeyboardOpen(KeyboardCallback, g_pucBuffer,
KEYBOARD_MEMORY_SIZE);
//
// Initialize the power configuration. This sets the power enable signal
// to be active high and does not enable the power fault.
//
USBHCDPowerConfigInit(0, USBHCD_VBUS_AUTO_HIGH | USBHCD_VBUS_FILTER);
//
// Initialize the USB controller for OTG operation with a 2ms polling
// rate.
//
USBOTGModeInit(0, 2000, g_pHCDPool, HCD_MEMORY_SIZE);
//
// Initialize the display driver.
//
CFAL96x64x16Init();
//
// Initialize the graphics context.
//
GrContextInit(&g_sContext, &g_sCFAL96x64x16);
//
// Fill the top part of the screen with blue to create the banner.
//
sRect.sXMin = 0;
sRect.sYMin = 0;
sRect.sXMax = GrContextDpyWidthGet(&g_sContext) - 1;
sRect.sYMax = (2 * DISPLAY_BANNER_HEIGHT) - 1;
GrContextForegroundSet(&g_sContext, DISPLAY_BANNER_BG);
GrRectFill(&g_sContext, &sRect);
//
// Change foreground for white text.
//
GrContextForegroundSet(&g_sContext, DISPLAY_TEXT_FG);
//
// Put the application name in the middle of the banner.
//
GrContextFontSet(&g_sContext, g_pFontFixed6x8);
GrStringDrawCentered(&g_sContext, "usb-host-", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 4, 0);
GrStringDrawCentered(&g_sContext, "keyboard", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 14, 0);
//
// Calculate the number of characters that will fit on a line.
// Make sure to leave a small border for the text box.
//
g_ulCharsPerLine = (GrContextDpyWidthGet(&g_sContext) - 4) /
GrFontMaxWidthGet(g_pFontFixed6x8);
//
// Calculate the number of lines per usable text screen. This requires
// taking off space for the top and bottom banners and adding a small bit
// for a border.
//
g_ulLinesPerScreen = (GrContextDpyHeightGet(&g_sContext) -
(3*(DISPLAY_BANNER_HEIGHT + 1)))/
GrFontHeightGet(g_pFontFixed6x8);
//
// Open and instance of the keyboard class driver.
//
UARTprintf("Host Keyboard Application\n");
//
// Initial update of the screen.
//
UpdateStatus();
//
// The main loop for the application.
//
while(1)
{
//
// Tell the OTG library code how much time has passed in
// milliseconds since the last call.
//
USBOTGMain(GetTickms());
//
// Has the USB mode changed since last time we checked?
//
if(g_eCurrentUSBMode != eLastMode)
{
//
// Remember the new mode.
//
eLastMode = g_eCurrentUSBMode;
switch(eLastMode)
{
case USB_MODE_HOST:
pcString = "HOST";
break;
case USB_MODE_DEVICE:
pcString = "DEVICE";
break;
case USB_MODE_NONE:
pcString = "NONE";
break;
default:
pcString = "UNKNOWN";
break;
}
UARTprintf("USB mode changed to %s\n", pcString);
}
switch(g_eUSBState)
{
//
// This state is entered when they keyboard is first detected.
//
case STATE_KEYBOARD_INIT:
{
//
// Initialized the newly connected keyboard.
//
USBHKeyboardInit(g_ulKeyboardInstance);
//
// Proceed to the keyboard connected state.
//
g_eUSBState = STATE_KEYBOARD_CONNECTED;
//
// Update the screen now that the keyboard has been
// initialized.
//
UpdateStatus();
USBHKeyboardModifierSet(g_ulKeyboardInstance, g_ulModifiers);
break;
}
case STATE_KEYBOARD_UPDATE:
{
//
// If the application detected a change that required an
// update to be sent to the keyboard to change the modifier
// state then call it and return to the connected state.
//
g_eUSBState = STATE_KEYBOARD_CONNECTED;
USBHKeyboardModifierSet(g_ulKeyboardInstance, g_ulModifiers);
break;
}
case STATE_KEYBOARD_CONNECTED:
{
//
// Nothing is currently done in the main loop when the keyboard
// is connected.
//
break;
}
case STATE_UNKNOWN_DEVICE:
{
//
// Nothing to do as the device is unknown.
//
break;
}
case STATE_NO_DEVICE:
{
//
// Nothing is currently done in the main loop when the keyboard
// is not connected.
//
break;
}
default:
{
break;
}
}
}
}
//*****************************************************************************
//
// This example demonstrates how to send a string of data to the UART.
//
//*****************************************************************************
int
main(void)
{
//
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
//
ROM_FPUEnable();
ROM_FPULazyStackingEnable();
//
// Set the clocking to run directly from the crystal.
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_1 | SYSCTL_USE_OSC | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// Enable the GPIO port that is used for the on-board LED.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
//
// Enable the GPIO pins for the LED (PF2).
//
ROM_GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_2);
//
// Enable the peripherals used by this example.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_UART0);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
//
// Enable processor interrupts.
//
ROM_IntMasterEnable();
//
// Set GPIO A0 and A1 as UART pins.
//
GPIOPinConfigure(GPIO_PA0_U0RX);
GPIOPinConfigure(GPIO_PA1_U0TX);
ROM_GPIOPinTypeUART(GPIO_PORTA_BASE, GPIO_PIN_0 | GPIO_PIN_1);
//
// Configure the UART for 115,200, 8-N-1 operation.
//
ROM_UARTConfigSetExpClk(UART0_BASE, ROM_SysCtlClockGet(), 115200,
(UART_CONFIG_WLEN_8 | UART_CONFIG_STOP_ONE |
UART_CONFIG_PAR_NONE));
//
// Enable the UART interrupt.
//
ROM_IntEnable(INT_UART0);
ROM_UARTIntEnable(UART0_BASE, UART_INT_RX | UART_INT_RT);
//
// Prompt for text to be entered.
//
UARTSend((uint8_t *)"\033[2JEnter text: ", 16);
//
// Loop forever echoing data through the UART.
//
while(1)
{
}
}
/*---------------------------------------------------------------------------*/
int
main(void)
{
//
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
//
ROM_FPUEnable();
ROM_FPULazyStackingEnable();
//
// Set the clocking to run at 80MHz
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_2_5 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
leds_init();
uart0_init(0);
printf("\rStarting Contiki on LM4F120 Launchpad...\n\r");
clock_init();
process_init();
process_start(&sensors_process, NULL);
process_start(&etimer_process, NULL);
ctimer_init();
/* Networking stack. */
NETSTACK_RADIO.init();
NETSTACK_RDC.init();
NETSTACK_MAC.init();
NETSTACK_NETWORK.init();
{
rimeaddr_t rimeaddr;
rimeaddr.u8[0] = 0x00;
rimeaddr.u8[1] = 0x02;
rimeaddr_set_node_addr(&rimeaddr);
}
process_start(&tcpip_process, NULL);
process_start(&uip_fw_process, NULL);
uip_init();
uip_ipaddr(&hostaddr, 172, 16, 0, 2);
uip_ipaddr_copy(&meshif.ipaddr, &hostaddr);
uip_sethostaddr(&hostaddr);
uip_ipaddr(&netmask, 255, 255, 0, 0);
uip_setnetmask(&netmask);
uip_over_mesh_set_net(&hostaddr, &netmask);
uip_fw_default(&meshif);
//uip_fw_register(&slipif);
uip_over_mesh_init(UIP_OVER_MESH_CHANNEL);
autostart_start(autostart_processes);
while (1)
{
process_run();
}
return 0;
}
void setup_fpu(void)
{
ROM_FPUEnable();
ROM_FPULazyStackingEnable();
}
//*****************************************************************************
//
// This example demonstrates how to send a string of data to the UART.
//
//*****************************************************************************
int
main(void)
{
tRectangle sRect;
tContext sContext;
//
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
//
ROM_FPULazyStackingEnable();
//
// Set the clocking to run directly from the crystal.
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_1 | SYSCTL_USE_OSC | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// Initialize the display driver.
//
CFAL96x64x16Init();
//
// Initialize the graphics context.
//
GrContextInit(&sContext, &g_sCFAL96x64x16);
//
// Fill the top part of the screen with blue to create the banner.
//
sRect.i16XMin = 0;
sRect.i16YMin = 0;
sRect.i16XMax = GrContextDpyWidthGet(&sContext) - 1;
sRect.i16YMax = 9;
GrContextForegroundSet(&sContext, ClrDarkBlue);
GrRectFill(&sContext, &sRect);
//
// Change foreground for white text.
//
GrContextForegroundSet(&sContext, ClrWhite);
//
// Put the application name in the middle of the banner.
//
GrContextFontSet(&sContext, g_psFontFixed6x8);
GrStringDrawCentered(&sContext, "uart-echo", -1,
GrContextDpyWidthGet(&sContext) / 2, 4, 0);
//
// Initialize the display and write some instructions.
//
GrStringDrawCentered(&sContext, "Connect a", -1,
GrContextDpyWidthGet(&sContext) / 2, 20, false);
GrStringDrawCentered(&sContext, "terminal", -1,
GrContextDpyWidthGet(&sContext) / 2, 30, false);
GrStringDrawCentered(&sContext, "to UART0.", -1,
GrContextDpyWidthGet(&sContext) / 2, 40, false);
GrStringDrawCentered(&sContext, "115000,N,8,1", -1,
GrContextDpyWidthGet(&sContext) / 2, 50, false);
//
// Enable the peripherals used by this example.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_UART0);
//
// Enable processor interrupts.
//
ROM_IntMasterEnable();
//
// Set GPIO A0 and A1 as UART pins.
//
ROM_GPIOPinTypeUART(GPIO_PORTA_BASE, GPIO_PIN_0 | GPIO_PIN_1);
//
// Configure the UART for 115,200, 8-N-1 operation.
//
ROM_UARTConfigSetExpClk(UART0_BASE, ROM_SysCtlClockGet(), 115200,
(UART_CONFIG_WLEN_8 | UART_CONFIG_STOP_ONE |
UART_CONFIG_PAR_NONE));
//
// Enable the UART interrupt.
//
ROM_IntEnable(INT_UART0);
ROM_UARTIntEnable(UART0_BASE, UART_INT_RX | UART_INT_RT);
//
// Prompt for text to be entered.
//
UARTSend((uint8_t *)"Enter text: ", 12);
//
// Loop forever echoing data through the UART.
//
while(1)
{
}
}
//*****************************************************************************
//
// This is the main application entry function.
//
//*****************************************************************************
int
main(void)
{
volatile uint32_t ui32Loop;
uint32_t ui32TxCount;
uint32_t ui32RxCount;
//
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
//
ROM_FPULazyStackingEnable();
//
// Set the clocking to run from the PLL at 50MHz
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// Enable the GPIO port that is used for the on-board LED.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
//
// Enable the GPIO pins for the LED (PF2 & PF3).
//
ROM_GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_3 | GPIO_PIN_2);
//
// Open UART0 and show the application name on the UART.
//
ConfigureUART();
UARTprintf("\033[2JTiva C Series USB bulk device example\n");
UARTprintf("---------------------------------\n\n");
//
// Not configured initially.
//
g_bUSBConfigured = false;
//
// Enable the GPIO peripheral used for USB, and configure the USB
// pins.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
ROM_GPIOPinTypeUSBAnalog(GPIO_PORTD_BASE, GPIO_PIN_4 | GPIO_PIN_5);
//
// Enable the system tick.
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / SYSTICKS_PER_SECOND);
ROM_SysTickIntEnable();
ROM_SysTickEnable();
//
// Tell the user what we are up to.
//
UARTprintf("Configuring USB\n");
//
// Initialize the transmit and receive buffers.
//
USBBufferInit(&g_sTxBuffer);
USBBufferInit(&g_sRxBuffer);
//
// Set the USB stack mode to Device mode with VBUS monitoring.
//
USBStackModeSet(0, eUSBModeForceDevice, 0);
//
// Pass our device information to the USB library and place the device
// on the bus.
//
USBDBulkInit(0, &g_sBulkDevice);
//
// Wait for initial configuration to complete.
//
UARTprintf("Waiting for host...\n");
//
// Clear our local byte counters.
//
ui32RxCount = 0;
ui32TxCount = 0;
//
// Main application loop.
//
while(1)
{
//
// See if any data has been transferred.
//
if((ui32TxCount != g_ui32TxCount) || (ui32RxCount != g_ui32RxCount))
{
//
// Has there been any transmit traffic since we last checked?
//
if(ui32TxCount != g_ui32TxCount)
{
//
// Turn on the Green LED.
//
GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_3, GPIO_PIN_3);
//
// Delay for a bit.
//
for(ui32Loop = 0; ui32Loop < 150000; ui32Loop++)
{
}
//
// Turn off the Green LED.
//
GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_3, 0);
//
// Take a snapshot of the latest transmit count.
//
ui32TxCount = g_ui32TxCount;
}
//
// Has there been any receive traffic since we last checked?
//
if(ui32RxCount != g_ui32RxCount)
{
//
// Turn on the Blue LED.
//
GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_2, GPIO_PIN_2);
//
// Delay for a bit.
//
for(ui32Loop = 0; ui32Loop < 150000; ui32Loop++)
{
}
//
// Turn off the Blue LED.
//
GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_2, 0);
//
// Take a snapshot of the latest receive count.
//
ui32RxCount = g_ui32RxCount;
}
//
// Update the display of bytes transferred.
//
UARTprintf("\rTx: %d Rx: %d", ui32TxCount, ui32RxCount);
}
}
}
