signed char fReadByteLoop(unsigned int blknum)
{
bTargetAddress = 0;
bTargetDataPtr = 0;
while(bTargetDataPtr < TARGET_DATABUFF_LEN)
{
//Send Read Byte vector and then get a byte from Target
SendVector(read_byte_v, 4);
// Set the drive here because SendByte() does not
SetSDATAStrong();
SendByte(bTargetAddress,7);
RunClock(2); // Run two SCLK cycles between writing and reading
SetSDATAHiZ(); // Set to HiZ so Target can drive SDATA
bTargetDataIN = bReceiveByte();
RunClock(1);
SendVector(read_byte_v + 1, 1); // Send the ReadByte Vector End
// Test the Byte that was read from the Target against the original
// value (already in the 128-Byte array "abTargetDataOUT[]"). If it
// matches, then bump the address & pointer,loop-back and continue.
// If it does NOT match abort the loop and return and error.
//if (bTargetDataIN != abTargetDataOUT[bTargetDataPtr])
if (bTargetDataIN != pSocData[blknum*TARGET_DATABUFF_LEN + bTargetDataPtr])
{
#ifdef TX_ON
UART_PutCRLF();
UART_CPutString("bTargetDataIN : ");
UART_PutHexByte(bTargetDataIN);
UART_CPutString(" abTargetDataOUT : ");
UART_PutHexByte(pSocData[blknum*TARGET_DATABUFF_LEN + bTargetDataPtr]);
#endif
return(BLOCK_ERROR);
}
bTargetDataPtr++;
// Increment the address by 2 to accomodate 7-Bit addressing
// (puts the 7-bit address into MSBit locations for "SendByte()").
bTargetAddress += 2;
}
return(PASS);
}
int main(){
CyGlobalIntEnable;
SPI_Start();
UART_Start();
isrIRQ_Start();
isrBTN_Start();
ADC_Start();
CyDelay(100);
UART_PutString("Test TX and Rx Payload\r\n");
NRF_INIT_t tx;
tx.channel = CHANNEL;
tx.isTX = true;
tx.RF_SETUP_DR = NRF_RF_SETUP_RF_DR_1000;
tx.RF_SETUP_PWR = 0;
tx.SETUP_RETR_ARC = NRF_SETUP_RETR_ARC_15;
tx.SETUP_RETR_ARD = NRF_SETUP_RETR_ARD_1500;
// Test Rx Payload
NRF_WriteSingleRegister(NRF_DYNPD, 0x01u);
NRF_WriteSingleRegister(NRF_FEATURE, 0x06u);
NRF_SetRxPayloadSize(NRF_RX_PW_P0, PAYLOAD_SIZE);
//
NRF_SetRxAddress(ADDR, sizeof(ADDR));
NRF_SetTxAddress(ADDR, sizeof(ADDR));
NRF_Init(&tx);
NRF_TxTransmit(data, sizeof(data));
CyDelay(4000);
NRF_GetRetransmissionsCount(&test);
UART_PutHexByte(test);
UART_PutCRLF();
for(;;){
/*
if(pressCount){
if(3 == pressCount) pressCount = 0;
ADCoutput = ADC_Read32();
data[1] = (ADCoutput & 0xFF00) >> 8;
data[2] = ADCoutput & 0xFF;
data[6] = pressCount;
NRF_TxTransmit(data, sizeof(data));
}
*/
count++;
if(12 == count){
if(250 == pressCount){
pressCount = 0;
}
if(250 == test){
test = 0;
}
count = 0;
test++;
data[9] = test;
data[0] = pressCount;
ADCoutput = ADC_Read32();
data[1] = (ADCoutput & 0xFF00) >> 8;
data[2] = ADCoutput & 0xFF;
NRF_TxTransmit(data, sizeof(data));
}
CyDelay(20);
NRF_GetLostPackets(&test);
if(0x0F == test){
NRF_ResetStatusIRQ(NRF_STATUS_MAX_RT);
}
UART_PutHexByte(test);
UART_PutCRLF();
if(isrFlag){
isrFlag = false;
if(NRF_GetStatus() & 0x40u){ /* RX_DR: Data Received */
do{
NRF_RxPayload(RXdata, sizeof(RXdata));
NRF_ResetStatusIRQ(NRF_STATUS_RX_DR);
NRF_ReadSingleRegister(NRF_FIFO_STATUS, &status);
}while(!(status & 0x01));
printFlag = true;
}else if(NRF_GetStatus() & 0x60u){ /* TX_DS: Data Sent */
LED_Write(~LED_Read());
NRF_ResetStatusIRQ(NRF_STATUS_TX_DS);
}else if(NRF_GetStatus() & 0x10u){ /* MAX_RT: Retry Timeout */
MAX_Write(~MAX_Read());
NRF_ResetStatusIRQ(NRF_STATUS_MAX_RT);
}
}
if(printFlag){
UART_PutHexByte(RXdata[0]);
UART_PutString("\r\n");
UART_PutHexByte(RXdata[1]);
UART_PutString("\r\n");
UART_PutHexByte(RXdata[2]);
UART_PutString("\r\n");
UART_PutHexByte(RXdata[3]);
UART_PutString("\r\n");
UART_PutHexByte(RXdata[4]);
UART_PutString("\r\n");
UART_PutHexByte(RXdata[5]);
UART_PutString("\r\n");
UART_PutHexByte(RXdata[6]);
UART_PutString("\r\n");
UART_PutHexByte(RXdata[7]);
UART_PutString("\r\n");
UART_PutHexByte(RXdata[8]);
UART_PutString("\r\n");
UART_PutHexByte(RXdata[9]);
UART_PutString("\r\n");
printFlag = false;
}
}
}
// ============================================================================
// fVerifySiliconID()
// Returns:
// 0 if successful
// Si_ID_ERROR if timed out on handshake to the device.
// ============================================================================
signed char fVerifySiliconID(void)
{
SendVector(id_setup_2, num_bits_id_setup_2);
fIsError = fDetectHiLoTransition();
if (fIsError)
{
#ifdef TX_ON
UART_PutCRLF();
UART_CPutString("fDetectHiLoTransition Error");
#endif
return(SiID_ERROR);
}
SendVector(wait_and_poll_end, num_bits_wait_and_poll_end);
SendVector(tsync_enable, num_bits_tsync_enable);
//Send Read ID vector and get Target ID
SendVector(read_id_v, 11); // Read-MSB Vector is the first 11-Bits
RunClock(2); // Two SCLK cycles between write & read
bTargetID[0] = bReceiveByte();
RunClock(1);
SendVector(read_id_v+2, 12); // 1+11 bits starting from the 3rd byte
RunClock(2); // Read-LSB Command
bTargetID[1] = bReceiveByte();
RunClock(1);
SendVector(read_id_v+4, 1); // 1 bit starting from the 5th byte
//read Revision ID from Accumulator A and Accumulator X
//SendVector(read_id_v+5, 11); //11 bits starting from the 6th byte
//RunClock(2);
//bTargetID[2] = bReceiveByte(); //Read from Acc.X
//RunClock(1);
//SendVector(read_id_v+7, 12); //1+11 bits starting from the 8th byte
//
//RunClock(2);
//bTargetID[3] = bReceiveByte(); //Read from Acc.A
//
//RunClock(1);
//SendVector(read_id_v+4, 1); //1 bit starting from the 5th byte,
SendVector(tsync_disable, num_bits_tsync_disable);
#ifdef TX_ON
// Print READ-ID
UART_PutCRLF();
UART_CPutString("Silicon-ID : ");
UART_PutChar(' ');
UART_PutHexByte(bTargetID[0]);
UART_PutChar(' ');
UART_PutHexByte(bTargetID[1]);
UART_PutChar(' ');
#endif
#ifdef LCD_ON
LCD_Char_Position(1, 0);
LCD_Char_PrintString("ID : ");
LCD_Char_PrintInt8(bTargetID[0]);
LCD_Char_PutChar(' ');
LCD_Char_PrintInt8(bTargetID[1]);
LCD_Char_PutChar(' ');
#endif
if (bTargetID[0] == target_id_v[0] && bTargetID[1] == target_id_v[1])
{
return(PASS);
}
else if (bTargetID[0] == target_id_v2[0] && bTargetID[1] == target_id_v2[1])
{
return(PASS);
}
else
{
printk("%x %x \n", bTargetID[0], bTargetID[1]);
return(SiID_ERROR);
}
}
int main(){
CyGlobalIntEnable;
isrSW_Start();
isr_Timer_Start();
UART_Start();
ADC_Start();
ADC_StartConvert();
CyDelay(50);
UART_PutString("nRF Tx\r\n");
NRF_INIT_t tx;
tx.channel = NRF_CHANNEL;
tx.isTX = true;
tx.RF_SETUP_DR = NRF_RF_SETUP_RF_DR_1000;
tx.RF_SETUP_PWR = NRF_RF_SETUP_RF_PWR_18;
tx.SETUP_RETR_ARC = NRF_SETUP_RETR_ARC_15;
tx.SETUP_RETR_ARD = NRF_SETUP_RETR_ARD_1500;
/* Start the component before anything else */
nRF_Tx_Start(&tx);
/* Test Dynamic Payload */
nRF_Tx_EnableDynamicPayload(NRF_DYNPD_DPL_P0);
nRF_Tx_SetRxPayloadSize(NRF_RX_PW_P0, PAYLOAD_SIZE);
nRF_Tx_SetRxAddress(ADDR, sizeof(ADDR));
nRF_Tx_SetTxAddress(ADDR, sizeof(ADDR));
Timer_Start();
for(;;){
if(true == isrTimerFlag){
// Stop the Timer just for fun
Timer_Stop();
test++;
data[0] = pressCount;
data[9] = test;
ADCoutput = ADC_Read32();
UART_PutString("Resultado de la conversion del ADC: ");
UART_PutHexInt((uint16_t)ADCoutput);
UART_PutCRLF();
data[1] = (ADCoutput & 0xFF00) >> 8;
data[2] = ADCoutput & 0xFF;
nRF_Tx_TxTransmit(data, sizeof(data));
isrTimerFlag = false;
// Start the Timer again
Timer_Start();
}
if(isrFlag){
if(nRF_Tx_GetStatus() & NRF_STATUS_RX_DR_MASK){
UART_PutString("Status: ");
UART_PutHexByte(nRF_Tx_GetStatus());
UART_PutCRLF();
UART_PutString("RX\r\n");
do{
nRF_Tx_RxPayload(RXdata, sizeof(RXdata));
nRF_Tx_ResetStatusIRQ(NRF_STATUS_RX_DR);
nRF_Tx_ReadSingleRegister(NRF_FIFO_STATUS, &status);
}while(!(status & NRF_STATUS_TX_FIFO_FULL));
printFlag = true;
}else if(nRF_Tx_GetStatus() & NRF_STATUS_TX_DS_MASK){
UART_PutString("Status: ");
UART_PutHexByte(nRF_Tx_GetStatus());
UART_PutCRLF();
UART_PutString("TX\r\n");
LED_Write(~LED_Read());
nRF_Tx_ResetStatusIRQ(NRF_STATUS_TX_DS);
}else if(nRF_Tx_GetStatus() & NRF_STATUS_MAX_RT_MASK){
UART_PutString("Status: ");
UART_PutHexByte(nRF_Tx_GetStatus());
UART_PutCRLF();
UART_PutString("Max RT\r\n");
MAX_Write(~MAX_Read());
nRF_Tx_ResetStatusIRQ(NRF_STATUS_MAX_RT);
}
isrFlag = false;
}
if(printFlag){
UART_PutHexByte(RXdata[0]);
UART_PutString("\r\n");
UART_PutHexByte(RXdata[1]);
UART_PutString("\r\n");
UART_PutHexByte(RXdata[2]);
UART_PutString("\r\n");
UART_PutHexByte(RXdata[3]);
UART_PutString("\r\n");
UART_PutHexByte(RXdata[4]);
UART_PutString("\r\n");
UART_PutHexByte(RXdata[5]);
UART_PutString("\r\n");
UART_PutHexByte(RXdata[6]);
UART_PutString("\r\n");
UART_PutHexByte(RXdata[7]);
UART_PutString("\r\n");
UART_PutHexByte(RXdata[8]);
UART_PutString("\r\n");
UART_PutHexByte(RXdata[9]);
UART_PutString("\r\n");
printFlag = false;
}
}
