/*
* ======== rxData ========
*/
static unsigned int rxData(unsigned char *pStr,
unsigned int length,
unsigned int timeout)
{
unsigned char recvResult;
unsigned int ret = 0;
recvResult = USBCDC_receiveData(pStr, length, USBCDCD_INTFNUM);
/*
* We will pend on a Semaphore_pend() if we received a
* USBCDC_RECEIVE_STARTED and block until we received all the data. If it
* returned a USBCDC_RECEIVE_COMPLETED; a callback has already occurred
* so we call Semaphore_post() to just consume it but it won't cause a
* context switch.
*/
if ((recvResult == USBCDC_RECEIVE_STARTED) || (recvResult == USBCDC_RECEIVE_COMPLETED)) {
if (!Semaphore_pend(semRxSerial, timeout)) {
USBCDC_abortReceive(&length, USBCDCD_INTFNUM);
}
ret = length;
}
return (ret);
}
/*----------------------------------------------------------------------------+
| Main Routine |
+----------------------------------------------------------------------------*/
VOID main(VOID)
{
WDTCTL = WDTPW + WDTHOLD; // Stop watchdog timer
Init_StartUp();
USB_init();
USB_setEnabledEvents(kUSB_VbusOnEvent+kUSB_VbusOffEvent+kUSB_receiveCompletedEvent
+kUSB_dataReceivedEvent+kUSB_UsbSuspendEvent+kUSB_UsbResumeEvent+kUSB_UsbResetEvent);
// Check if we're already physically attached to USB, and if so, connect to it
// This is the same function that gets called automatically when VBUS gets attached.
if (USB_connectionInfo() & kUSB_vbusPresent)
USB_handleVbusOnEvent();
//PWRVBUSonHandler();
while(1)
{
switch(USB_connectionState())
{
case ST_USB_DISCONNECTED:
__bis_SR_register(LPM3_bits + GIE); // Enter LPM3 w/interrupt
break;
case ST_USB_CONNECTED_NO_ENUM:
break;
case ST_ENUM_ACTIVE:
if(!bCommandBeingProcessed) // If no command is being processed, then make sure there's a rcv operation
{ // open to receive the start of the "packet"
if(!(USBCDC_intfStatus(0,&x,&y) & kUSBCDC_waitingForReceive)) // Only open it if we haven't already done so
if(USBCDC_receiveData(buffer,1,0) == kUSBCDC_busNotAvailable) // Start a receive operation for a single byte -- the "size" byte of the "packet"
{
USBCDC_abortReceive(&x,0); // Abort receive
break; // If bus is no longer available, escape out of the loop
}
}
__bis_SR_register(LPM0_bits + GIE); // Wait in LPM0 until a receive operation has completed
//__bis_SR_register(LPM0_bits + GIE);
if(bDataReceiveCompleted_event)
{
bDataReceiveCompleted_event = FALSE;
if(!bCommandBeingProcessed) // This means that the incoming byte is the start of the "packet" -- the "size" byte
{
if ((buffer[0]>=0x31) && (buffer[0]<= 0x39))
{
size = buffer[0]-0x30; // It's in ASCII, so convert it to a number
if(USBCDC_receiveData(buffer,size,0) == kUSBCDC_busNotAvailable) // And then open a rcv operation for that size
{
USBCDC_abortReceive(&x,0); // Abort receive
break; // If bus is no longer available, escape out of the loop
}
bCommandBeingProcessed = TRUE; // Now we're waiting for the "data" part of the "packet"
}
else
{
strcpy(outString,"\r\nEnter a valid number between 1 and 9\r\n\r\n"); // Prepare the outgoing string
if(cdcSendDataInBackground((BYTE*)outString,strlen(outString),0,0)) // Send the response over USB
{
USBCDC_abortSend(&x,0); // Operation may still be open; cancel it
break; // If the send fails, escape the main loop
}
bCommandBeingProcessed = FALSE; // Now we're back to waiting for the "size" byte
}
}
else // This means that the incoming data is the "data" part of the "packet"
{
strcpy(outString,"\r\nI received your packet with size of "); // Prepare the outgoing string
buffer[bufferLen-1]= 0;
c[0] = (char)(size+'0');
c[1] = 0;
outString[64] = 0; // Convert the size back to ASCII
strcat(outString,c);
strcat(outString," bytes.\r\n\r\n");
if(cdcSendDataInBackground((BYTE*)outString,strlen(outString),0,0)) // Send the response over USB
{
USBCDC_abortSend(&x,0); // Operation may still be open; cancel it
break; // If the send fails, escape the main loop
}
bCommandBeingProcessed = FALSE; // Now we're back to waiting for the "size" byte
}
}
break;
case ST_ENUM_SUSPENDED:
__bis_SR_register(LPM3_bits + GIE); // Enter LPM3 w/interrupt
break;
case ST_ENUM_IN_PROGRESS:
break;
case ST_NOENUM_SUSPENDED:
__bis_SR_register(LPM3_bits + GIE);
_NOP();
break;
case ST_ERROR:
_NOP();
break;
default:;
}
} // while(1)
} //main()
VOID main(VOID)
{
WDTCTL = WDTPW + WDTHOLD; // Stop watchdog timer
Init_StartUp(); //initialize device
USB_init();
USB_setEnabledEvents(USBEVIE);
// See if we're already attached physically to USB, and if so, connect to it
// Normally applications don't invoke the event handlers, but this is an exception.
if (USB_connectionInfo() & kUSB_vbusPresent)
USB_handleVbusOnEvent();
while(1)
{
switch(USB_connectionState())
{
case ST_USB_DISCONNECTED:
__bis_SR_register(LPM3_bits + GIE); // Enter LPM3 w/interrupt
_NOP();
break;
case ST_USB_CONNECTED_NO_ENUM:
break;
case ST_ENUM_ACTIVE:
__bis_SR_register(LPM0_bits + GIE); // Enter LPM0 until an event occurs.
// This flag would have been set by the handleDataReceived event; this event is only enabled when waiting
// for 'press any key'
if(bCDCDataReceived_event)
{
bCDCDataReceived_event = FALSE;
// Change the event flags, in preparation for receiving 1K data
USBEVIE &= ~kUSB_dataReceivedEvent; // No more data-received. We only used this for 'press any key'
USBEVIE |= kUSB_receiveCompletedEvent; // But enable receive-completed; we want to be prompted when 1K data has been received
USB_setEnabledEvents(USBEVIE);
USBCDC_rejectData(0); // We don't care what char the key-press was
// Prompt user for 1K data
strcpy(outString,"I'm ready to receive 1K of data.\r\n"); // Prepare the outgoing string
if(cdcSendDataWaitTilDone((BYTE*)outString,strlen(outString),0,0)) // Send it over USB
{
USBCDC_abortSend(&x,0); // It failed for some reason; abort and leave the main loop
break;
}
// Set up rcv operation for 1K data
if(USBCDC_receiveData(dataBuff,1024,0) == kUSBCDC_busNotAvailable) //first USBCDC_receiveData
{
USBCDC_abortReceive(&x,0); // It failed because of surprise removal or suspended by host;
break; // abort and leave the main loop
}
}
// This flag would have been set by the handleReceiveCompleted event; this event is only enabled
// while receiving 1K data, and signals that all 1K has been received
if(bDataReceiveCompleted_event)
{
bDataReceiveCompleted_event = FALSE;
strcpy(outString,"Thanks for the data.\r\n"); // Prepare the outgoing string
if(cdcSendDataInBackground((BYTE*)outString,strlen(outString),0,0)) //Send the response over USB
{
USBCDC_abortSend(&x,0); // It failed for some reason; abort and leave the main loop
break;
}
// Change the event flags, in preparation for 'press any key'
USBEVIE &= ~kUSB_receiveCompletedEvent; // No more receive-completed.
USBEVIE |= kUSB_dataReceivedEvent; // This will tell us that data -- any data -- has arrived (i.e., a key-press)
USB_setEnabledEvents(USBEVIE);
}
break;
case ST_ENUM_SUSPENDED:
__bis_SR_register(LPM3_bits + GIE); // Enter LPM3 w/ interrupts
_NOP();
break;
case ST_ENUM_IN_PROGRESS:
break;
case ST_NOENUM_SUSPENDED:
__bis_SR_register(LPM3_bits + GIE);
_NOP();
break;
case ST_ERROR:
_NOP();
break;
default:;
}
} // while(1)
} //main()
