//*****************************************************************************
//
// Initialize the USB library and set things up so that we can handle USB HID
// keyboard attachment.
//
//*****************************************************************************
void
USBKeyboardInit(void)
{
//
// Initially wait for device connection.
//
g_eUSBState = STATE_NO_DEVICE;
//
// Configure the power pins for host controller.
//
GPIOPinTypeUSBDigital(GPIO_PORTA_BASE, GPIO_PIN_6 | GPIO_PIN_7);
//
// Register the host class drivers.
//
USBHCDRegisterDrivers(0, g_ppHostClassDrivers, g_ulNumHostClassDrivers);
//
// Open an instance of the keyboard driver. The keyboard does not need
// to be present at this time, this just save a place for it and allows
// the applications to be notified when a keyboard is present.
//
g_ulKeyboardInstance = USBHKeyboardOpen(KeyboardCallback, g_pucBuffer,
KEYBOARD_MEMORY_SIZE);
//
// Initialize the power configuration. This sets the power enable signal
// to be active high and does not enable the power fault.
//
USBHCDPowerConfigInit(0, USBHCD_VBUS_AUTO_HIGH | USBHCD_VBUS_FILTER);
//
// Initialize the USB controller for host mode operation.
//
USBHCDInit(0, g_pHCDPool, HCD_MEMORY_SIZE);
}
//*****************************************************************************
//
// This is the main loop that runs the application.
//
//*****************************************************************************
int
main(void)
{
tRectangle sRect;
tUSBMode eLastMode;
char *pcString;
//
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
//
ROM_FPULazyStackingEnable();
//
// Set the system clock to run at 50MHz from the PLL.
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// Initially wait for device connection.
//
g_eUSBState = STATE_NO_DEVICE;
eLastMode = USB_MODE_OTG;
g_eCurrentUSBMode = USB_MODE_OTG;
//
// Enable Clocking to the USB controller.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_USB0);
//
// Configure the required pins for USB operation.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOG);
ROM_GPIOPinConfigure(GPIO_PG4_USB0EPEN);
ROM_GPIOPinTypeUSBDigital(GPIO_PORTG_BASE, GPIO_PIN_4);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOL);
ROM_GPIOPinTypeUSBAnalog(GPIO_PORTL_BASE, GPIO_PIN_6 | GPIO_PIN_7);
ROM_GPIOPinTypeUSBAnalog(GPIO_PORTB_BASE, GPIO_PIN_0 | GPIO_PIN_1);
//
// Configure SysTick for a 100Hz interrupt.
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / TICKS_PER_SECOND);
ROM_SysTickEnable();
ROM_SysTickIntEnable();
//
// Enable Interrupts
//
ROM_IntMasterEnable();
//
// Enable clocking to the UART and associated GPIO
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_UART0);
//
// Configure the relevant pins such that UART0 owns them.
//
ROM_GPIOPinTypeUART(GPIO_PORTA_BASE, GPIO_PIN_0 | GPIO_PIN_1);
//
// Open UART0 for debug output.
//
UARTStdioInit(0);
//
// Initialize the USB stack mode and pass in a mode callback.
//
USBStackModeSet(0, USB_MODE_OTG, ModeCallback);
//
// Register the host class drivers.
//
USBHCDRegisterDrivers(0, g_ppHostClassDrivers, g_ulNumHostClassDrivers);
//
// Open an instance of the keyboard driver. The keyboard does not need
// to be present at this time, this just save a place for it and allows
// the applications to be notified when a keyboard is present.
//
g_ulKeyboardInstance = USBHKeyboardOpen(KeyboardCallback, g_pucBuffer,
KEYBOARD_MEMORY_SIZE);
//
// Initialize the power configuration. This sets the power enable signal
// to be active high and does not enable the power fault.
//
USBHCDPowerConfigInit(0, USBHCD_VBUS_AUTO_HIGH | USBHCD_VBUS_FILTER);
//
// Initialize the USB controller for OTG operation with a 2ms polling
// rate.
//
USBOTGModeInit(0, 2000, g_pHCDPool, HCD_MEMORY_SIZE);
//
// Initialize the display driver.
//
CFAL96x64x16Init();
//
// Initialize the graphics context.
//
GrContextInit(&g_sContext, &g_sCFAL96x64x16);
//
// Fill the top part of the screen with blue to create the banner.
//
sRect.sXMin = 0;
sRect.sYMin = 0;
sRect.sXMax = GrContextDpyWidthGet(&g_sContext) - 1;
sRect.sYMax = (2 * DISPLAY_BANNER_HEIGHT) - 1;
GrContextForegroundSet(&g_sContext, DISPLAY_BANNER_BG);
GrRectFill(&g_sContext, &sRect);
//
// Change foreground for white text.
//
GrContextForegroundSet(&g_sContext, DISPLAY_TEXT_FG);
//
// Put the application name in the middle of the banner.
//
GrContextFontSet(&g_sContext, g_pFontFixed6x8);
GrStringDrawCentered(&g_sContext, "usb-host-", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 4, 0);
GrStringDrawCentered(&g_sContext, "keyboard", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 14, 0);
//
// Calculate the number of characters that will fit on a line.
// Make sure to leave a small border for the text box.
//
g_ulCharsPerLine = (GrContextDpyWidthGet(&g_sContext) - 4) /
GrFontMaxWidthGet(g_pFontFixed6x8);
//
// Calculate the number of lines per usable text screen. This requires
// taking off space for the top and bottom banners and adding a small bit
// for a border.
//
g_ulLinesPerScreen = (GrContextDpyHeightGet(&g_sContext) -
(3*(DISPLAY_BANNER_HEIGHT + 1)))/
GrFontHeightGet(g_pFontFixed6x8);
//
// Open and instance of the keyboard class driver.
//
UARTprintf("Host Keyboard Application\n");
//
// Initial update of the screen.
//
UpdateStatus();
//
// The main loop for the application.
//
while(1)
{
//
// Tell the OTG library code how much time has passed in
// milliseconds since the last call.
//
USBOTGMain(GetTickms());
//
// Has the USB mode changed since last time we checked?
//
if(g_eCurrentUSBMode != eLastMode)
{
//
// Remember the new mode.
//
eLastMode = g_eCurrentUSBMode;
switch(eLastMode)
{
case USB_MODE_HOST:
pcString = "HOST";
break;
case USB_MODE_DEVICE:
pcString = "DEVICE";
break;
case USB_MODE_NONE:
pcString = "NONE";
break;
default:
pcString = "UNKNOWN";
break;
}
UARTprintf("USB mode changed to %s\n", pcString);
}
switch(g_eUSBState)
{
//
// This state is entered when they keyboard is first detected.
//
case STATE_KEYBOARD_INIT:
{
//
// Initialized the newly connected keyboard.
//
USBHKeyboardInit(g_ulKeyboardInstance);
//
// Proceed to the keyboard connected state.
//
g_eUSBState = STATE_KEYBOARD_CONNECTED;
//
// Update the screen now that the keyboard has been
// initialized.
//
UpdateStatus();
USBHKeyboardModifierSet(g_ulKeyboardInstance, g_ulModifiers);
break;
}
case STATE_KEYBOARD_UPDATE:
{
//
// If the application detected a change that required an
// update to be sent to the keyboard to change the modifier
// state then call it and return to the connected state.
//
g_eUSBState = STATE_KEYBOARD_CONNECTED;
USBHKeyboardModifierSet(g_ulKeyboardInstance, g_ulModifiers);
break;
}
case STATE_KEYBOARD_CONNECTED:
{
//
// Nothing is currently done in the main loop when the keyboard
// is connected.
//
break;
}
case STATE_UNKNOWN_DEVICE:
{
//
// Nothing to do as the device is unknown.
//
break;
}
case STATE_NO_DEVICE:
{
//
// Nothing is currently done in the main loop when the keyboard
// is not connected.
//
break;
}
default:
{
break;
}
}
}
}
//*****************************************************************************
//
// This is the main loop that runs the application.
//
//*****************************************************************************
int
main(void)
{
tRectangle sRect;
//
// Set the clocking to run directly from the crystal.
//
SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_8MHZ);
//
// Enable the peripherals used by this example.
//
SysCtlPeripheralEnable(SYSCTL_PERIPH_UART0);
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
//
// Configure the relevant pins such that UART0 owns them.
//
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
GPIOPinTypeUART(GPIO_PORTA_BASE, GPIO_PIN_0 | GPIO_PIN_1);
//
// Open UART0 for debug output.
//
UARTStdioInit(0);
//
// Enable the USB mux GPIO.
//
SysCtlPeripheralEnable(USB_MUX_GPIO_PERIPH);
//
// The LM3S3748 board uses a USB mux that must be switched to use the
// host connector and not the device connector.
//
GPIOPinTypeGPIOOutput(USB_MUX_GPIO_BASE, USB_MUX_GPIO_PIN);
GPIOPinWrite(USB_MUX_GPIO_BASE, USB_MUX_GPIO_PIN, USB_MUX_SEL_HOST);
//
// Configure the power pins for host controller.
//
GPIOPinTypeUSBDigital(GPIO_PORTH_BASE, GPIO_PIN_3 | GPIO_PIN_4);
//
// Initialize the display driver.
//
Formike128x128x16Init();
//
// Turn on the backlight.
//
Formike128x128x16BacklightOn();
//
// Initialize the graphics context.
//
GrContextInit(&g_sContext, &g_sFormike128x128x16);
//
// Fill the top 15 rows of the screen with blue to create the banner.
//
sRect.sXMin = 0;
sRect.sYMin = 0;
sRect.sXMax = GrContextDpyWidthGet(&g_sContext) - 1;
sRect.sYMax = DISPLAY_BANNER_HEIGHT;
GrContextForegroundSet(&g_sContext, DISPLAY_BANNER_BG);
GrRectFill(&g_sContext, &sRect);
//
// Put a white box around the banner.
//
GrContextForegroundSet(&g_sContext, ClrWhite);
GrRectDraw(&g_sContext, &sRect);
//
// Put the application name in the middle of the banner.
//
GrContextFontSet(&g_sContext, g_pFontFixed6x8);
GrStringDrawCentered(&g_sContext, "usb_host_keyboard", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 7, 0);
//
// Calculate the number of characters that will fit on a line.
// Make sure to leave a small border for the text box.
//
g_ulCharsPerLine = (GrContextDpyWidthGet(&g_sContext) - 4) /
GrFontMaxWidthGet(g_pFontFixed6x8);
//
// Calculate the number of lines per usable text screen. This requires
// taking off space for the top and bottom banners and adding a small bit
// for a border.
//
g_ulLinesPerScreen = (GrContextDpyHeightGet(&g_sContext) -
(2*(DISPLAY_BANNER_HEIGHT + 1)))/
GrFontHeightGet(g_pFontFixed6x8);
//
// Register the host class drivers.
//
USBHCDRegisterDrivers(0, g_ppHostClassDrivers, g_ulNumHostClassDrivers);
//
// Open and instance of the keyboard class driver.
//
UARTprintf("Host Keyboard Application\n");
//
// Open an instance of the keyboard driver. The keyboard does not need
// to be present at this time, this just save a place for it and allows
// the applications to be notified when a keyboard is present.
//
g_ulKeyboardInstance = USBHKeyboardOpen(KeyboardCallback, g_pucBuffer,
KEYBOARD_MEMORY_SIZE);
//
// Initialize the power configuration. This sets the power enable signal
// to be active high and does not enable the power fault.
//
USBHCDPowerConfigInit(0, USBHCD_VBUS_AUTO_HIGH);
//
// Initialize the host controller stack.
//
USBHCDInit(0, g_pHCDPool, HCD_MEMORY_SIZE);
//
// Call the main loop for the Host controller driver.
//
USBHCDMain();
//
// Initial update of the screen.
//
UpdateStatus();
//
// The main loop for the application.
//
while(1)
{
switch(g_eUSBState)
{
//
// This state is entered when they keyboard is first detected.
//
case STATE_KEYBOARD_INIT:
{
//
// Initialized the newly connected keyboard.
//
USBHKeyboardInit(g_ulKeyboardInstance);
//
// Proceed to the keyboard connected state.
//
g_eUSBState = STATE_KEYBOARD_CONNECTED;
USBHKeyboardModifierSet(g_ulKeyboardInstance, g_ulModifiers);
//
// Update the screen now that the keyboard has been
// initialized.
//
UpdateStatus();
break;
}
case STATE_KEYBOARD_UPDATE:
{
//
// If the application detected a change that required an
// update to be sent to the keyboard to change the modifier
// state then call it and return to the connected state.
//
g_eUSBState = STATE_KEYBOARD_CONNECTED;
USBHKeyboardModifierSet(g_ulKeyboardInstance, g_ulModifiers);
break;
}
case STATE_KEYBOARD_CONNECTED:
{
//
// Nothing is currently done in the main loop when the keyboard
// is connected.
//
break;
}
case STATE_UNKNOWN_DEVICE:
{
//
// Nothing to do as the device is unknown.
//
break;
}
case STATE_NO_DEVICE:
{
//
// Nothing is currently done in the main loop when the keyboard
// is not connected.
//
break;
}
default:
{
break;
}
}
//
// Periodic call the main loop for the Host controller driver.
//
USBHCDMain();
}
}
//*****************************************************************************
//
// This is the main loop that runs the application.
//
//*****************************************************************************
int
main(void)
{
tRectangle sRect;
unsigned int i;
unsigned char *src, *dest;
//
//configures arm interrupt controller to generate raster interrupt
//
SetupIntc();
//
//Configures raster to display image
//
SetUpLCD();
/* configuring the base ceiling */
RasterDMAFBConfig(SOC_LCDC_0_REGS,
(unsigned int)(g_pucBuffer+PALETTE_OFFSET),
(unsigned int)(g_pucBuffer+PALETTE_OFFSET) + sizeof(g_pucBuffer) - 2 - PALETTE_OFFSET,
0);
RasterDMAFBConfig(SOC_LCDC_0_REGS,
(unsigned int)(g_pucBuffer+PALETTE_OFFSET),
(unsigned int)(g_pucBuffer+PALETTE_OFFSET) + sizeof(g_pucBuffer) - 2 - PALETTE_OFFSET,
1);
// Copy palette info into buffer
src = (unsigned char *) palette_32b;
dest = (unsigned char *) (g_pucBuffer+PALETTE_OFFSET);
for( i = 4; i < (PALETTE_SIZE+4); i++)
{
*dest++ = *src++;
}
GrOffScreen16BPPInit(&g_sSHARP480x272x16Display, g_pucBuffer, LCD_WIDTH, LCD_HEIGHT);
GrContextInit(&g_sContext, &g_sSHARP480x272x16Display);
/* enable End of frame interrupt */
RasterEndOfFrameIntEnable(SOC_LCDC_0_REGS);
/* enable raster */
RasterEnable(SOC_LCDC_0_REGS);
ConfigRasterDisplayEnable();
//
// Fill the top 15 rows of the screen with blue to create the banner.
//
sRect.sXMin = 0;
sRect.sYMin = 0;
sRect.sXMax = GrContextDpyWidthGet(&g_sContext) - 1;
sRect.sYMax = DISPLAY_BANNER_HEIGHT;
//
// Set the banner background.
//
GrContextForegroundSet(&g_sContext, DISPLAY_BANNER_BG);
GrRectFill(&g_sContext, &sRect);
//
// Put a white box around the banner.
//
GrContextForegroundSet(&g_sContext, ClrWhite);
GrRectDraw(&g_sContext, &sRect);
//
// Put the application name in the middle of the banner.
//
GrContextFontSet(&g_sContext, &g_sFontCm20);
GrStringDrawCentered(&g_sContext, "usb host keyboard", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 10, 0);
//
//Setup the interrupt controller
//
#ifdef _TMS320C6X
SetupDSPINTCInt();
ConfigureDSPINTCIntUSB();
#else
SetupAINTCInt();
ConfigureAINTCIntUSB();
#endif
DelayTimerSetup();
//
// Calculate the number of characters that will fit on a line.
// Make sure to leave a small border for the text box.
//
g_ulCharsPerLine = (GrContextDpyWidthGet(&g_sContext) - 4) /
GrFontMaxWidthGet(&g_sFontCm20);
//
// Calculate the number of lines per usable text screen. This requires
// taking off space for the top and bottom banners and adding a small bit
// for a border.
//
g_ulLinesPerScreen = (GrContextDpyHeightGet(&g_sContext) -
(2*(DISPLAY_BANNER_HEIGHT + 1)))/
GrFontHeightGet(&g_sFontCm20);
//
// Register the host class drivers.
//
USBHCDRegisterDrivers(0, g_ppHostClassDrivers, g_ulNumHostClassDrivers);
// Open an instance of the keyboard driver. The keyboard does not need
// to be present at this time, this just save a place for it and allows
// the applications to be notified when a keyboard is present.
//
g_ulKeyboardInstance = USBHKeyboardOpen(KeyboardCallback, g_pucBuffer,
KEYBOARD_MEMORY_SIZE);
//
// Initialize the power configuration. This sets the power enable signal
// to be active high and does not enable the power fault.
//
USBHCDPowerConfigInit(0, USBHCD_VBUS_AUTO_HIGH);
//
// Initialize the host controller stack.
//
USBHCDInit(0, g_pHCDPool, HCD_MEMORY_SIZE);
//
// Call the main loop for the Host controller driver.
//
USBHCDMain();
//
// Initial update of the screen.
//
UpdateStatus();
//
// The main loop for the application.
//
while(1)
{
switch(g_eUSBState)
{
//
// This state is entered when they keyboard is first detected.
//
case STATE_KEYBOARD_INIT:
{
//
// Initialized the newly connected keyboard.
//
USBHKeyboardInit(g_ulKeyboardInstance);
//
// Proceed to the keyboard connected state.
//
g_eUSBState = STATE_KEYBOARD_CONNECTED;
//
// Update the screen now that the keyboard has been
// initialized.
//
UpdateStatus();
break;
}
case STATE_KEYBOARD_UPDATE:
{
//
// If the application detected a change that required an
// update to be sent to the keyboard to change the modifier
// state then call it and return to the connected state.
//
g_eUSBState = STATE_KEYBOARD_CONNECTED;
USBHKeyboardModifierSet(g_ulKeyboardInstance, g_ulModifiers);
break;
}
case STATE_KEYBOARD_CONNECTED:
{
//
// Nothing is currently done in the main loop when the keyboard
// is connected.
//
break;
}
case STATE_UNKNOWN_DEVICE:
{
//
// Nothing to do as the device is unknown.
//
break;
}
case STATE_NO_DEVICE:
{
//
// Nothing is currently done in the main loop when the keyboard
// is not connected.
//
break;
}
default:
{
break;
}
}
//
// Periodic call the main loop for the Host controller driver.
//
USBHCDMain();
}
}
//*****************************************************************************
//
// This is the main loop that runs the application.
//
//*****************************************************************************
int
main(void)
{
//
// Set the clocking to run from the PLL at 50MHz.
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// Enable the peripherals used by this example.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_UART0);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOH);
//
// Enable the UART.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
GPIOPinConfigure(GPIO_PA0_U0RX);
GPIOPinConfigure(GPIO_PA1_U0TX);
ROM_GPIOPinTypeUART(GPIO_PORTA_BASE, GPIO_PIN_0 | GPIO_PIN_1);
UARTStdioInit(0);
UARTprintf("\033[2JHost Keyboard Application\n");
//
// Configure SysTick for a 100Hz interrupt.
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / TICKS_PER_SECOND);
ROM_SysTickEnable();
ROM_SysTickIntEnable();
//
// Enable Clocking to the USB controller.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_USB0);
//
// Configure the power pins for host controller.
//
GPIOPinConfigure(GPIO_PH3_USB0EPEN);
GPIOPinConfigure(GPIO_PH4_USB0PFLT);
ROM_GPIOPinTypeUSBDigital(GPIO_PORTH_BASE, GPIO_PIN_3 | GPIO_PIN_4);
//
// Initially wait for device connection.
//
g_eUSBState = STATE_NO_DEVICE;
//
// Initialize the USB stack mode and pass in a mode callback.
//
USBStackModeSet(0, USB_MODE_OTG, ModeCallback);
//
// Register the host class drivers.
//
USBHCDRegisterDrivers(0, g_ppHostClassDrivers, g_ulNumHostClassDrivers);
//
// Open an instance of the keyboard driver. The keyboard does not need
// to be present at this time, this just save a place for it and allows
// the applications to be notified when a keyboard is present.
//
g_ulKeyboardInstance = USBHKeyboardOpen(KeyboardCallback, g_pucBuffer,
KEYBOARD_MEMORY_SIZE);
//
// Initialize the power configuration. This sets the power enable signal
// to be active high and does not enable the power fault.
//
USBHCDPowerConfigInit(0, USBHCD_VBUS_AUTO_HIGH | USBHCD_VBUS_FILTER);
//
// Initialize the USB controller for OTG operation with a 2ms polling
// rate.
//
USBOTGModeInit(0, 2000, g_pHCDPool, HCD_MEMORY_SIZE);
//
// The main loop for the application.
//
while(1)
{
//
// Tell the OTG state machine how much time has passed in
// milliseconds since the last call.
//
USBOTGMain(GetTickms());
switch(g_eUSBState)
{
//
// This state is entered when they keyboard is first detected.
//
case STATE_KEYBOARD_INIT:
{
//
// Initialized the newly connected keyboard.
//
USBHKeyboardInit(g_ulKeyboardInstance);
//
// Proceed to the keyboard connected state.
//
g_eUSBState = STATE_KEYBOARD_CONNECTED;
USBHKeyboardModifierSet(g_ulKeyboardInstance, g_ulModifiers);
break;
}
case STATE_KEYBOARD_UPDATE:
{
//
// If the application detected a change that required an
// update to be sent to the keyboard to change the modifier
// state then call it and return to the connected state.
//
g_eUSBState = STATE_KEYBOARD_CONNECTED;
USBHKeyboardModifierSet(g_ulKeyboardInstance, g_ulModifiers);
break;
}
case STATE_KEYBOARD_CONNECTED:
{
//
// Nothing is currently done in the main loop when the keyboard
// is connected.
//
break;
}
case STATE_UNKNOWN_DEVICE:
{
//
// Nothing to do as the device is unknown.
//
break;
}
case STATE_NO_DEVICE:
{
//
// Nothing is currently done in the main loop when the keyboard
// is not connected.
//
break;
}
default:
{
break;
}
}
}
}
//*****************************************************************************
//
// The main application loop.
//
//*****************************************************************************
int
main(void)
{
uint32_t ui32SysClock, ui32PLLRate;
#ifdef USE_ULPI
uint32_t ui32Setting;
#endif
//
// Set the application to run at 120 MHz with a PLL frequency of 480 MHz.
//
ui32SysClock = MAP_SysCtlClockFreqSet((SYSCTL_XTAL_25MHZ |
SYSCTL_OSC_MAIN | SYSCTL_USE_PLL |
SYSCTL_CFG_VCO_480), 120000000);
//
// Set the part pin out appropriately for this device.
//
PinoutSet();
#ifdef USE_ULPI
//
// Switch the USB ULPI Pins over.
//
USBULPIPinoutSet();
//
// Enable USB ULPI with high speed support.
//
ui32Setting = USBLIB_FEATURE_ULPI_HS;
USBOTGFeatureSet(0, USBLIB_FEATURE_USBULPI, &ui32Setting);
//
// Setting the PLL frequency to zero tells the USB library to use the
// external USB clock.
//
ui32PLLRate = 0;
#else
//
// Save the PLL rate used by this application.
//
ui32PLLRate = 480000000;
#endif
//
// Initialize the connection status.
//
g_sStatus.bConnected = false;
//
// Initially there are no modifiers set.
//
g_sStatus.ui32Modifiers = 0;
//
// Enable Clocking to the USB controller.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_USB0);
//
// Enable Interrupts
//
ROM_IntMasterEnable();
//
// Initialize the USB stack mode and pass in a mode callback.
//
USBStackModeSet(0, eUSBModeHost, 0);
//
// Register the host class drivers.
//
USBHCDRegisterDrivers(0, g_ppHostClassDrivers, g_ui32NumHostClassDrivers);
//
// Open an instance of the keyboard driver. The keyboard does not need
// to be present at this time, this just save a place for it and allows
// the applications to be notified when a keyboard is present.
//
g_psKeyboard = USBHKeyboardOpen(KeyboardCallback, 0, 0);
//
// Initialize the power configuration. This sets the power enable signal
// to be active high and does not enable the power fault.
//
USBHCDPowerConfigInit(0, USBHCD_VBUS_AUTO_HIGH | USBHCD_VBUS_FILTER);
//
// Tell the USB library the CPU clock and the PLL frequency. This is a
// new requirement for TM4C129 devices.
//
USBHCDFeatureSet(0, USBLIB_FEATURE_CPUCLK, &ui32SysClock);
USBHCDFeatureSet(0, USBLIB_FEATURE_USBPLL, &ui32PLLRate);
//
// Initialize the USB controller for Host mode.
//
USBHCDInit(0, g_pui8HCDPool, sizeof(g_pui8HCDPool));
//
// Initialize the GUI elements.
//
UIInit(ui32SysClock);
//
// The main loop for the application.
//
while(1)
{
//
// Call the USB library to let non-interrupt code run.
//
USBHCDMain();
//
// Call the keyboard and mass storage main routines.
//
KeyboardMain();
}
}