VOID
EFIAPI
GdbPutChar (
IN CHAR8 Char
)
{
UINT32 LSR = UartBase(PcdGet32(PcdOmap35xxConsoleUart)) + UART_LSR_REG;
UINT32 THR = UartBase(PcdGet32(PcdOmap35xxConsoleUart)) + UART_THR_REG;
while ((MmioRead8(LSR) & UART_LSR_TX_FIFO_E_MASK) == UART_LSR_TX_FIFO_E_NOT_EMPTY);
MmioWrite8(THR, Char);
}
CHAR8
EFIAPI
GdbGetChar (
VOID
)
{
UINT32 LSR = UartBase(PcdGet32(PcdOmap35xxConsoleUart)) + UART_LSR_REG;
UINT32 RBR = UartBase(PcdGet32(PcdOmap35xxConsoleUart)) + UART_RBR_REG;
CHAR8 Char;
while ((MmioRead8(LSR) & UART_LSR_RX_FIFO_E_MASK) == UART_LSR_RX_FIFO_E_EMPTY);
Char = MmioRead8(RBR);
return Char;
}
VOID
UartInit (
VOID
)
{
UINTN Uart = FixedPcdGet32(PcdOmap35xxConsoleUart);
UINT32 UartBaseAddress = UartBase(Uart);
// Set MODE_SELECT=DISABLE before trying to initialize or modify DLL, DLH registers.
MmioWrite32 (UartBaseAddress + UART_MDR1_REG, UART_MDR1_MODE_SELECT_DISABLE);
// Put device in configuration mode.
MmioWrite32 (UartBaseAddress + UART_LCR_REG, UART_LCR_DIV_EN_ENABLE);
// Programmable divisor N = 48Mhz/16/115200 = 26
MmioWrite32 (UartBaseAddress + UART_DLL_REG, 3000000/FixedPcdGet64 (PcdUartDefaultBaudRate)); // low divisor
MmioWrite32 (UartBaseAddress + UART_DLH_REG, 0); // high divisor
// Enter into UART operational mode.
MmioWrite32 (UartBaseAddress + UART_LCR_REG, UART_LCR_DIV_EN_DISABLE | UART_LCR_CHAR_LENGTH_8);
// Force DTR and RTS output to active
MmioWrite32 (UartBaseAddress + UART_MCR_REG, UART_MCR_RTS_FORCE_ACTIVE | UART_MCR_DTR_FORCE_ACTIVE);
// Clear & enable fifos
MmioWrite32 (UartBaseAddress + UART_FCR_REG, UART_FCR_TX_FIFO_CLEAR | UART_FCR_RX_FIFO_CLEAR | UART_FCR_FIFO_ENABLE);
// Restore MODE_SELECT
MmioWrite32 (UartBaseAddress + UART_MDR1_REG, UART_MDR1_MODE_SELECT_UART_16X);
}
/**
Read data from serial device and save the datas in buffer.
@param Buffer Point of data buffer which need to be writed.
@param NumberOfBytes Number of output bytes which are cached in Buffer.
@retval 0 Read data failed.
@retval !0 Aactual number of bytes read from serial device.
**/
UINTN
EFIAPI
SerialPortRead (
OUT UINT8 *Buffer,
IN UINTN NumberOfBytes
)
{
UINT32 LSR = UartBase(PcdGet32(PcdOmap35xxConsoleUart)) + UART_LSR_REG;
UINT32 RBR = UartBase(PcdGet32(PcdOmap35xxConsoleUart)) + UART_RBR_REG;
UINTN Count;
for (Count = 0; Count < NumberOfBytes; Count++, Buffer++) {
while ((MmioRead8(LSR) & UART_LSR_RX_FIFO_E_MASK) == UART_LSR_RX_FIFO_E_EMPTY);
*Buffer = MmioRead8(RBR);
}
return NumberOfBytes;
}
/**
Write data to serial device.
@param Buffer Point of data buffer which need to be writed.
@param NumberOfBytes Number of output bytes which are cached in Buffer.
@retval 0 Write data failed.
@retval !0 Actual number of bytes writed to serial device.
**/
UINTN
EFIAPI
SerialPortWrite (
IN UINT8 *Buffer,
IN UINTN NumberOfBytes
)
{
UINT32 LSR = UartBase(PcdGet32(PcdOmap35xxConsoleUart)) + UART_LSR_REG;
UINT32 THR = UartBase(PcdGet32(PcdOmap35xxConsoleUart)) + UART_THR_REG;
UINTN Count;
for (Count = 0; Count < NumberOfBytes; Count++, Buffer++) {
while ((MmioRead8(LSR) & UART_LSR_TX_FIFO_E_MASK) == UART_LSR_TX_FIFO_E_NOT_EMPTY);
MmioWrite8(THR, *Buffer);
}
return NumberOfBytes;
}
/**
Check to see if any data is avaiable to be read from the debug device.
@retval EFI_SUCCESS At least one byte of data is avaiable to be read
@retval EFI_NOT_READY No data is avaiable to be read
@retval EFI_DEVICE_ERROR The serial device is not functioning properly
**/
BOOLEAN
EFIAPI
SerialPortPoll (
VOID
)
{
UINT32 LSR = UartBase(PcdGet32(PcdOmap35xxConsoleUart)) + UART_LSR_REG;
if ((MmioRead8(LSR) & UART_LSR_RX_FIFO_E_MASK) == UART_LSR_RX_FIFO_E_NOT_EMPTY) {
return TRUE;
} else {
return FALSE;
}
}
