void MyWIFI_Connect(void) {
UINT8 ConnectionProfileID;
UINT8 channelList[] = MY_DEFAULT_CHANNEL_LIST;
/* create a Connection Profile */
WF_CPCreate(&ConnectionProfileID);
WF_CPSetSsid(ConnectionProfileID,
AppConfig.MySSID,
AppConfig.SsidLength);
WF_CPSetNetworkType(ConnectionProfileID, MY_DEFAULT_NETWORK_TYPE);
WF_CASetScanType(MY_DEFAULT_SCAN_TYPE);
WF_CASetChannelList(channelList, sizeof (channelList));
// The Retry Count parameter tells the WiFi Connection manager how many attempts to make when trying
// to connect to an existing network. In the Infrastructure case, the default is to retry forever so that
// if the AP is turned off or out of range, the radio will continue to attempt a connection until the
// AP is eventually back on or in range. In the Adhoc case, the default is to retry 3 times since the
// purpose of attempting to establish a network in the Adhoc case is only to verify that one does not
// initially exist. If the retry count was set to WF_RETRY_FOREVER in the AdHoc mode, an AdHoc network
// would never be established. The constants MY_DEFAULT_LIST_RETRY_COUNT_ADHOC and
// MY_DEFAULT_LIST_RETRY_COUNT_INFRASTRUCTURE have been created specifically for the June 2011 MAL release.
#if (MY_DEFAULT_NETWORK_TYPE == WF_ADHOC)
WF_CASetListRetryCount(MY_DEFAULT_LIST_RETRY_COUNT_ADHOC);
#else
WF_CASetListRetryCount(MY_DEFAULT_LIST_RETRY_COUNT_INFRASTRUCTURE);
#endif
WF_CASetEventNotificationAction(MY_DEFAULT_EVENT_NOTIFICATION_LIST);
WF_CASetBeaconTimeout(40);
WF_CPSetSecurity(ConnectionProfileID,
AppConfig.SecurityMode,
AppConfig.WepKeyIndex, /* only used if WEP enabled */
AppConfig.SecurityKey,
AppConfig.SecurityKeyLength);
MyConsole_SendMsg("Start WiFi Connect\n");
WF_CMConnect(ConnectionProfileID);
}
/*****************************************************************************
* FUNCTION: void WF_Connect(void)
*
* RETURNS: None
*
* PARAMS: none
*
* NOTES: This routine creates a Connection Profile Entry, Initializes it
* then creates the connection algorithm and establishes the WiFi
* connection according to the Profile settings.
* Customize this function as needed for your application.
*
* Wifi Direct, ensure following parameters are set up properly
* - AppConfig.MySSID = "DIRECT-"
* - sizeof(channelList) == 3)
* - channelList[0] == 1
* - channelList[1] == 6
* - channelList[2] == 11
*
*****************************************************************************/
void WF_Connect(void)
{
uint8_t ConnectionProfileID;
uint8_t channelList[] = MY_DEFAULT_CHANNEL_LIST;
uint8_t channelList_postscan[] = MY_DEFAULT_CHANNEL_LIST_POSTSCAN;
/* create a Connection Profile */
WF_CPCreate(&ConnectionProfileID);
AppConfig.passPhraseToKeyFlag = 0;
// Enables or disables the MRF24W Regional Domain with RF module FW version 0x3106 or earlier
// With RF module FW version 0x3107 and future releases, this function is NOT supported due to changes
// in FCC requirements, which does not allow programming of the regional domain.
WF_SetRegionalDomain(MY_DEFAULT_DOMAIN);
if ((AppConfig.networkType == WF_SOFT_AP) || (AppConfig.networkType == WF_ADHOC)) {
/**********************************************************************/
/* Append Last 4 digits to MAC address to SSID - Creating unique SSID */
/* Wifi comm demo SSID : MCHP_xxxx */
/* Wifi G demo SSID : MCHP_G_xxxx */
/**********************************************************************/
sprintf((char *) AppConfig.MySSID, "MCHP_G_%02x%02x", AppConfig.MyMACAddr.v[4], AppConfig.MyMACAddr.v[5]);
sprintf((char *) AppConfig.NetBIOSName, "%s%02x%02x", MY_DEFAULT_HOST_NAME, AppConfig.MyMACAddr.v[4], AppConfig.MyMACAddr.v[5]);
size_t i = 0;
// in the following while loop, all lower case letters have been changed to upper case ones
// because browser automatically translates lower case letters to upper case
while (i < sizeof (AppConfig.NetBIOSName)) {
if (((*((char *) AppConfig.NetBIOSName + i)) >= 'a') & ((*((char *) AppConfig.NetBIOSName + i)) <= 'z')) {
*((char *) AppConfig.NetBIOSName + i) = *((char *) AppConfig.NetBIOSName + i) - 32;
} else if (*((char *) AppConfig.NetBIOSName + i) == '\0')
break;
i++;
}
FormatNetBIOSName(AppConfig.NetBIOSName);
}
AppConfig.SsidLength = strlen((char *) (AppConfig.MySSID));
WF_CPSetSsid(ConnectionProfileID, AppConfig.MySSID, AppConfig.SsidLength);
WF_CPSetNetworkType(ConnectionProfileID, AppConfig.networkType);
if (AppConfig.networkType == WF_ADHOC) {
WF_CPSetAdHocBehavior(ConnectionProfileID, WF_ADHOC_CONNECT_THEN_START);
}
#if !defined(MRF24WG)
Delay10us(10); /* required for MRF24WB */
#endif
#if WF_HOST_DERIVE_KEY_FROM_PASSPHRASE == WF_ENABLED
if (AppConfig.SecurityMode == WF_SECURITY_WPA_AUTO_WITH_PASS_PHRASE) {
WF_ConvPassphraseToKey(AppConfig.SecurityKeyLength, AppConfig.SecurityKey,
AppConfig.SsidLength, AppConfig.MySSID);
AppConfig.SecurityMode--;
AppConfig.SecurityKeyLength = 32;
AppConfig.passPhraseToKeyFlag = 1;
}
#endif /* #if WF_HOST_DERIVE_KEY_FROM_PASSPHRASE == WF_ENABLED */
switch (AppConfig.SecurityMode) {
case WF_SECURITY_OPEN:
WF_CPSetSecurity(ConnectionProfileID, WF_SECURITY_OPEN, 0, NULL, 0);
break;
case WF_SECURITY_WEP_40:
// assume key 0
WF_CPSetSecurity(ConnectionProfileID, AppConfig.SecurityMode, 0, AppConfig.SecurityKey, 5);
break;
case WF_SECURITY_WEP_104:
// assume key 0
WF_CPSetSecurity(ConnectionProfileID, AppConfig.SecurityMode, 0, AppConfig.SecurityKey, 13);
break;
case WF_SECURITY_WPA_AUTO_WITH_KEY:
WF_CPSetSecurity(ConnectionProfileID, WF_SECURITY_WPA_AUTO_WITH_KEY,
0, AppConfig.SecurityKey, 32);
break;
default:
WF_ASSERT(false);
break;
}
WF_CASetScanType(MY_DEFAULT_SCAN_TYPE);
if (((CFGCXT.type != WF_SOFT_AP)&&(CFGCXT.prevWLAN == WF_SOFT_AP)) || (AppConfig.networkType != WF_SOFT_AP)) {
WF_CASetChannelList(channelList_postscan, sizeof (channelList_postscan));
} else {
WF_CASetChannelList(channelList, sizeof (channelList));
}
// The Retry Count parameter tells the WiFi Connection manager how many attempts to make when trying
// to connect to an existing network. In the Infrastructure case, the default is to retry forever so that
// if the AP is turned off or out of range, the radio will continue to attempt a connection until the
// AP is eventually back on or in range. In the Adhoc case, the default is to retry 3 times since the
// purpose of attempting to establish a network in the Adhoc case is only to verify that one does not
// initially exist. If the retry count was set to WF_RETRY_FOREVER in the AdHoc mode, an AdHoc network
// would never be established. The constants MY_DEFAULT_LIST_RETRY_COUNT_ADHOC and
// MY_DEFAULT_LIST_RETRY_COUNT_INFRASTRUCTURE have been created specifically for the June 2011 MAL release.
if ((AppConfig.networkType == CFG_WF_ADHOC) || (AppConfig.networkType == CFG_WF_SOFT_AP)) {
WF_CASetListRetryCount(ADHOC_RETRY_COUNT);
} else /* AppConfig.networkType == CFG_WF_INFRASTRUCTURE */ {
WF_CASetListRetryCount(MY_DEFAULT_LIST_RETRY_COUNT_INFRASTRUCTURE);
}
WF_CASetEventNotificationAction(MY_DEFAULT_EVENT_NOTIFICATION_LIST);
#if defined(WF_USE_POWER_SAVE_FUNCTIONS)
#if (MY_DEFAULT_PS_POLL == WF_ENABLED)
WF_PsPollEnable(true);
#else
WF_PsPollDisable();
#endif
#endif
WF_CASetBeaconTimeout(MY_DEFAULT_BEACON_TIMEOUT);
#if defined(STACK_USE_UART)
WF_OutputConnectionInfo(&AppConfig);
#endif
if (AppConfig.networkType == CFG_WF_SOFT_AP) {
#if (WF_SOFTAP_SEND_KEEP_ALIVE == WF_ENABLED)
WF_SetLinkDownThreshold(WF_SOFTAP_LINK_LOST_THRESHOLD);
#endif
} else { // AppConfig.networkType != CFG_WF_SOFT_AP
#if (WF_CHECK_LINK_STATUS == WF_ENABLED)
WF_SetLinkDownThreshold(WF_LINK_LOST_THRESHOLD);
#endif
}
// Initiates connection to BSS
WF_CMConnect(ConnectionProfileID);
}
/*****************************************************************************
* FUNCTION: WF_Connect
*
* RETURNS: None
*
* PARAMS: None
*
* NOTES: Connects to an 802.11 network. Customize this function as needed
* for your application.
*****************************************************************************/
static void WF_Connect(void)
{
UINT8 ConnectionProfileID;
UINT8 channelList[] = MY_DEFAULT_CHANNEL_LIST;
#if defined(WF_USE_POWER_SAVE_FUNCTIONS)
BOOL PsPollEnabled;
#endif
/* create a Connection Profile */
WF_CPCreate(&ConnectionProfileID);
#if defined(STACK_USE_UART)
putrsUART("Set SSID (");
putsUART(AppConfig.MySSID);
putrsUART(")\r\n");
#endif
WF_CPSetSsid(ConnectionProfileID,
AppConfig.MySSID,
AppConfig.SsidLength);
#if defined(STACK_USE_UART)
putrsUART("Set Network Type\r\n");
#endif
WF_CPSetNetworkType(ConnectionProfileID, AppConfig.networkType);
if (AppConfig.networkType == WF_ADHOC)
{
WF_CPSetAdHocBehavior(ConnectionProfileID, WF_ADHOC_CONNECT_THEN_START);
}
#if defined(STACK_USE_UART)
putrsUART("Set Security\r\n");
#endif
switch(AppConfig.SecurityMode) {
case WF_SECURITY_OPEN:
WF_CPSetSecurity(ConnectionProfileID, WF_SECURITY_OPEN, 0, NULL, 0);
break;
case WF_SECURITY_WEP_40:
// assume key 0
WF_CPSetSecurity(ConnectionProfileID, AppConfig.SecurityMode, 0, AppConfig.SecurityKey, 5);
break;
case WF_SECURITY_WEP_104:
// assume key 0
WF_CPSetSecurity(ConnectionProfileID, AppConfig.SecurityMode, 0, AppConfig.SecurityKey, 13);
break;
case WF_SECURITY_WPA_AUTO_WITH_PASS_PHRASE:
WF_CPSetSecurity(ConnectionProfileID, WF_SECURITY_WPA_AUTO_WITH_PASS_PHRASE,
0, AppConfig.SecurityKey, strlen((char*)AppConfig.SecurityKey));
break;
case WF_SECURITY_WPA_AUTO_WITH_KEY:
WF_CPSetSecurity(ConnectionProfileID, WF_SECURITY_WPA_AUTO_WITH_KEY,
0, AppConfig.SecurityKey, 32);
break;
default:
{
}
//#if defined(STACK_USE_UART)
// putrsUART("\r\n\r\nCaptain this should NOT happen.\r\n\r\n");
//#endif
}
#if defined(STACK_USE_UART)
putrsUART("Set Scan Type\r\n");
#endif
WF_CASetScanType(MY_DEFAULT_SCAN_TYPE);
#if defined(STACK_USE_UART)
putrsUART("Set Channel List\r\n");
#endif
WF_CASetChannelList(channelList, sizeof(channelList));
#if defined(STACK_USE_UART)
putrsUART("Set list retry count\r\n");
#endif
WF_CASetListRetryCount(MY_DEFAULT_LIST_RETRY_COUNT);
#if defined(STACK_USE_UART)
putrsUART("Set Event Notify\r\n");
#endif
WF_CASetEventNotificationAction(MY_DEFAULT_EVENT_NOTIFICATION_LIST);
#if defined(WF_USE_POWER_SAVE_FUNCTIONS)
PsPollEnabled = (MY_DEFAULT_PS_POLL == WF_ENABLED);
if (!PsPollEnabled)
{
/* disable low power (PS-Poll) mode */
#if defined(STACK_USE_UART)
putrsUART("Disable PS-Poll\r\n");
#endif
WF_PsPollDisable();
}
else
{
/* Enable low power (PS-Poll) mode */
#if defined(STACK_USE_UART)
putrsUART("Enable PS-Poll\r\n");
#endif
WF_PsPollEnable(TRUE);
}
#endif
#if defined(STACK_USE_UART)
putrsUART("Set Beacon Timeout\r\n");
#endif
WF_CASetBeaconTimeout(40);
#if defined(STACK_USE_UART)
putrsUART("Start WiFi Connect\r\n");
#endif
WF_CMConnect(ConnectionProfileID);
}
/*****************************************************************************
* FUNCTION: WF_Connect
*
* RETURNS: None
*
* PARAMS: None
*
* NOTES: Connects to an 802.11 network. Customize this function as needed
* for your application.
*****************************************************************************/
static void WF_Connect(void)
{
UINT8 ConnectionProfileID;
UINT8 channelList[] = MY_DEFAULT_CHANNEL_LIST;
#if defined(WF_USE_POWER_SAVE_FUNCTIONS)
BOOL PsPollEnabled;
#endif
/* create a Connection Profile */
WF_CPCreate(&ConnectionProfileID);
#if defined(STACK_USE_UART)
putrsUART("Set SSID (");
putsUART(AppConfig.MySSID);
putrsUART(")\r\n");
#endif
WF_CPSetSsid(ConnectionProfileID,
AppConfig.MySSID,
AppConfig.SsidLength);
#if defined(STACK_USE_UART)
putrsUART("Set Network Type\r\n");
#endif
WF_CPSetNetworkType(ConnectionProfileID, MY_DEFAULT_NETWORK_TYPE);
#if defined(STACK_USE_UART)
putrsUART("Set Scan Type\r\n");
#endif
WF_CASetScanType(MY_DEFAULT_SCAN_TYPE);
#if defined(STACK_USE_UART)
putrsUART("Set Channel List\r\n");
#endif
WF_CASetChannelList(channelList, sizeof(channelList));
#if defined(STACK_USE_UART)
putrsUART("Set list retry count\r\n");
#endif
// The Retry Count parameter tells the WiFi Connection manager how many attempts to make when trying
// to connect to an existing network. In the Infrastructure case, the default is to retry forever so that
// if the AP is turned off or out of range, the radio will continue to attempt a connection until the
// AP is eventually back on or in range. In the Adhoc case, the default is to retry 3 times since the
// purpose of attempting to establish a network in the Adhoc case is only to verify that one does not
// initially exist. If the retry count was set to WF_RETRY_FOREVER in the AdHoc mode, an AdHoc network
// would never be established. The constants MY_DEFAULT_LIST_RETRY_COUNT_ADHOC and
// MY_DEFAULT_LIST_RETRY_COUNT_INFRASTRUCTURE have been created specifically for the June 2011 MAL release.
#if defined(EZ_CONFIG_STORE)
if (AppConfig.networkType == WF_ADHOC)
WF_CASetListRetryCount(MY_DEFAULT_LIST_RETRY_COUNT_ADHOC);
else
WF_CASetListRetryCount(MY_DEFAULT_LIST_RETRY_COUNT_INFRASTRUCTURE);
#else
#if (MY_DEFAULT_NETWORK_TYPE == WF_ADHOC)
WF_CASetListRetryCount(MY_DEFAULT_LIST_RETRY_COUNT_ADHOC);
#else
WF_CASetListRetryCount(MY_DEFAULT_LIST_RETRY_COUNT_INFRASTRUCTURE);
#endif
#endif
#if defined(STACK_USE_UART)
putrsUART("Set Event Notify\r\n");
#endif
WF_CASetEventNotificationAction(MY_DEFAULT_EVENT_NOTIFICATION_LIST);
#if defined(WF_USE_POWER_SAVE_FUNCTIONS)
PsPollEnabled = (MY_DEFAULT_PS_POLL == WF_ENABLED);
if (!PsPollEnabled)
{
/* disable low power (PS-Poll) mode */
#if defined(STACK_USE_UART)
putrsUART("Disable PS-Poll\r\n");
#endif
WF_PsPollDisable();
}
else
{
/* Enable low power (PS-Poll) mode */
#if defined(STACK_USE_UART)
putrsUART("Enable PS-Poll\r\n");
#endif
WF_PsPollEnable(TRUE);
}
#endif
#if defined(STACK_USE_UART)
putrsUART("Set Beacon Timeout\r\n");
#endif
WF_CASetBeaconTimeout(40);
/* Set Security */
#if (MY_DEFAULT_WIFI_SECURITY_MODE == WF_SECURITY_OPEN)
#if defined(STACK_USE_UART)
putrsUART("Set Security (Open)\r\n");
#endif
#elif (MY_DEFAULT_WIFI_SECURITY_MODE == WF_SECURITY_WEP_40)
#if defined(STACK_USE_UART)
putrsUART("Set Security (WEP40)\r\n");
#endif
#elif (MY_DEFAULT_WIFI_SECURITY_MODE == WF_SECURITY_WEP_104)
#if defined(STACK_USE_UART)
putrsUART("Set Security (WEP104)\r\n");
#endif
#elif MY_DEFAULT_WIFI_SECURITY_MODE == WF_SECURITY_WPA_WITH_KEY
#if defined(STACK_USE_UART)
putrsUART("Set Security (WPA with key)\r\n");
#endif
#elif MY_DEFAULT_WIFI_SECURITY_MODE == WF_SECURITY_WPA2_WITH_KEY
#if defined(STACK_USE_UART)
putrsUART("Set Security (WPA2 with key)\r\n");
#endif
#elif MY_DEFAULT_WIFI_SECURITY_MODE == WF_SECURITY_WPA_WITH_PASS_PHRASE
#if defined(STACK_USE_UART)
putrsUART("Set Security (WPA with pass phrase)\r\n");
#endif
#elif MY_DEFAULT_WIFI_SECURITY_MODE == WF_SECURITY_WPA2_WITH_PASS_PHRASE
#if defined(STACK_USE_UART)
putrsUART("Set Security (WPA2 with pass phrase)\r\n");
#endif
#elif MY_DEFAULT_WIFI_SECURITY_MODE == WF_SECURITY_WPA_AUTO_WITH_KEY
#if defined(STACK_USE_UART)
putrsUART("Set Security (WPA with key, auto-select)\r\n");
#endif
#elif MY_DEFAULT_WIFI_SECURITY_MODE == WF_SECURITY_WPA_AUTO_WITH_PASS_PHRASE
#if defined(STACK_USE_UART)
putrsUART("Set Security (WPA with pass phrase, auto-select)\r\n");
#endif
#endif /* MY_DEFAULT_WIFI_SECURITY_MODE */
WF_CPSetSecurity(ConnectionProfileID,
AppConfig.SecurityMode,
AppConfig.WepKeyIndex, /* only used if WEP enabled */
AppConfig.SecurityKey,
AppConfig.SecurityKeyLength);
#if defined(STACK_USE_UART)
putrsUART("Start WiFi Connect\r\n");
#endif
WF_CMConnect(ConnectionProfileID);
}
/*****************************************************************************
* FUNCTION: WF_Connect
*
* RETURNS: None
*
* PARAMS: None
*
* NOTES: Connects to an 802.11 network. Customize this function as needed
* for your application.
*****************************************************************************/
void WF_Connect(void)
{
//UINT8 ConnectionProfileID;
UINT8 channelList[] = MY_DEFAULT_CHANNEL_LIST;
#if (MY_DEFAULT_NETWORK_TYPE == WF_SOFT_AP)
UINT8 channelList_postscan[] = MY_DEFAULT_CHANNEL_LIST_POSTSCAN;
#endif
/* create a Connection Profile */
WF_CPCreate(&ConnectionProfileID);
WF_SetRegionalDomain(MY_DEFAULT_DOMAIN);
WF_CPSetSsid(ConnectionProfileID,
AppConfig.MySSID,
AppConfig.SsidLength);
WF_CPSetNetworkType(ConnectionProfileID, AppConfig.networkType);
if (AppConfig.networkType == WF_ADHOC)
{
WF_CPSetAdHocBehavior(ConnectionProfileID, WF_ADHOC_CONNECT_THEN_START);
}
#if !defined(MRF24WG)
// Delay10us(10); //If necessary, give time to Roadrunner to clean message buffer, because Security message is a big data package
#endif
switch(AppConfig.SecurityMode) {
case WF_SECURITY_OPEN:
WF_CPSetSecurity(ConnectionProfileID, WF_SECURITY_OPEN, 0, NULL, 0);
break;
case WF_SECURITY_WEP_40:
// assume key 0
WF_CPSetSecurity(ConnectionProfileID, AppConfig.SecurityMode, 0, AppConfig.SecurityKey, 5);
break;
case WF_SECURITY_WEP_104:
// assume key 0
WF_CPSetSecurity(ConnectionProfileID, AppConfig.SecurityMode, 0, AppConfig.SecurityKey, 13);
break;
case WF_SECURITY_WPA_AUTO_WITH_PASS_PHRASE:
WF_CPSetSecurity(ConnectionProfileID, WF_SECURITY_WPA_AUTO_WITH_PASS_PHRASE,
0, AppConfig.SecurityKey, strlen((char*)AppConfig.SecurityKey));
break;
case WF_SECURITY_WPA_AUTO_WITH_KEY:
WF_CPSetSecurity(ConnectionProfileID, WF_SECURITY_WPA_AUTO_WITH_KEY,
0, AppConfig.SecurityKey, 32);
break;
default:
putrsUART("\r\n\r\nCaptain this should NOT happen.\r\n\r\n");
}
WF_CASetScanType(MY_DEFAULT_SCAN_TYPE);
#if (MY_DEFAULT_NETWORK_TYPE == WF_SOFT_AP)
if (((CFGCXT.type!=WF_SOFT_AP)&&(CFGCXT.prevWLAN==WF_SOFT_AP)) || (AppConfig.networkType!=WF_SOFT_AP))
{
// putrsUART("\r\n\r\nWF_Connect: Channel list update when transitioning from SoftAP to non-SoftAP or NOT in SoftAP..\r\n\r\n");
WF_CASetChannelList(channelList_postscan, sizeof(channelList_postscan));
}
else
{
WF_CASetChannelList(channelList, sizeof(channelList));
}
#else
WF_CASetChannelList(channelList, sizeof(channelList));
#endif // (MY_DEFAULT_NETWORK_TYPE == WF_SOFT_AP)
// The Retry Count parameter tells the WiFi Connection manager how many attempts to make when trying
// to connect to an existing network. In the Infrastructure case, the default is to retry forever so that
// if the AP is turned off or out of range, the radio will continue to attempt a connection until the
// AP is eventually back on or in range. In the Adhoc case, the default is to retry 3 times since the
// purpose of attempting to establish a network in the Adhoc case is only to verify that one does not
// initially exist. If the retry count was set to WF_RETRY_FOREVER in the AdHoc mode, an AdHoc network
// would never be established. The constants MY_DEFAULT_LIST_RETRY_COUNT_ADHOC and
// MY_DEFAULT_LIST_RETRY_COUNT_INFRASTRUCTURE have been created specifically for the June 2011 MAL release.
WF_CASetListRetryCount(ADHOC_RETRY_COUNT);
WF_CASetEventNotificationAction(MY_DEFAULT_EVENT_NOTIFICATION_LIST);
#if defined(WF_USE_POWER_SAVE_FUNCTIONS)
#if (MY_DEFAULT_PS_POLL == WF_ENABLED)
WF_PsPollEnable(TRUE);
#else
WF_PsPollDisable();
#endif
#endif
WF_CASetBeaconTimeout(MY_DEFAULT_BEACON_TIMEOUT);
#if defined(STACK_USE_UART)
WF_OutputConnectionInfo(&AppConfig);
#endif
#if (SOFTAP_CHECK_LINK_STATUS == WF_ENABLED)
WF_SetLinkDownThreshold(SOFTAP_LINK_FAILURE_THRESHOLD);
#endif
WF_CMConnect(ConnectionProfileID);
}
/*****************************************************************************
* FUNCTION: WF_Connect
*
* RETURNS: None
*
* PARAMS: None
*
* NOTES: Connects to an 802.11 network. Customize this function as needed
* for your application.
*****************************************************************************/
void WF_Connect(void)
{
//UINT8 ConnectionProfileID;
UINT8 channelList[] = MY_DEFAULT_CHANNEL_LIST;
/* create a Connection Profile */
WF_CPCreate(&ConnectionProfileID);
WF_SetRegionalDomain(MY_DEFAULT_DOMAIN);
WF_CPSetSsid(ConnectionProfileID,
AppConfig.MySSID,
AppConfig.SsidLength);
#if defined(WF_USE_HIDDEN_SSID)
WF_CPSetSsidType(ConnectionProfileID, FALSE);
#endif
WF_CPSetNetworkType(ConnectionProfileID, AppConfig.networkType);
if (AppConfig.networkType == WF_ADHOC)
{
WF_CPSetAdHocBehavior(ConnectionProfileID, WF_ADHOC_CONNECT_THEN_START);
}
switch(AppConfig.SecurityMode) {
case WF_SECURITY_OPEN:
WF_CPSetSecurity(ConnectionProfileID, WF_SECURITY_OPEN, 0, NULL, 0);
break;
case WF_SECURITY_WEP_40:
// assume key 0
WF_CPSetSecurity(ConnectionProfileID, AppConfig.SecurityMode, 0, AppConfig.SecurityKey, 5);
break;
case WF_SECURITY_WEP_104:
// assume key 0
WF_CPSetSecurity(ConnectionProfileID, AppConfig.SecurityMode, 0, AppConfig.SecurityKey, 13);
break;
case WF_SECURITY_WPA_AUTO_WITH_PASS_PHRASE:
WF_CPSetSecurity(ConnectionProfileID, WF_SECURITY_WPA_AUTO_WITH_PASS_PHRASE,
0, AppConfig.SecurityKey, strlen((char*)AppConfig.SecurityKey));
break;
case WF_SECURITY_WPA_AUTO_WITH_KEY:
WF_CPSetSecurity(ConnectionProfileID, WF_SECURITY_WPA_AUTO_WITH_KEY,
0, AppConfig.SecurityKey, 32);
break;
default:
putrsUART("\r\n\r\nCaptain this should NOT happen.\r\n\r\n");
}
WF_CASetScanType(MY_DEFAULT_SCAN_TYPE);
WF_CASetChannelList(channelList, sizeof(channelList));
// The Retry Count parameter tells the WiFi Connection manager how many attempts to make when trying
// to connect to an existing network. In the Infrastructure case, the default is to retry forever so that
// if the AP is turned off or out of range, the radio will continue to attempt a connection until the
// AP is eventually back on or in range. In the Adhoc case, the default is to retry 3 times since the
// purpose of attempting to establish a network in the Adhoc case is only to verify that one does not
// initially exist. If the retry count was set to WF_RETRY_FOREVER in the AdHoc mode, an AdHoc network
// would never be established. The constants MY_DEFAULT_LIST_RETRY_COUNT_ADHOC and
// MY_DEFAULT_LIST_RETRY_COUNT_INFRASTRUCTURE have been created specifically for the June 2011 MAL release.
WF_CASetListRetryCount(ADHOC_RETRY_COUNT);
WF_CASetEventNotificationAction(MY_DEFAULT_EVENT_NOTIFICATION_LIST);
#if defined(WF_USE_POWER_SAVE_FUNCTIONS)
#if (MY_DEFAULT_PS_POLL == WF_ENABLED)
WF_PsPollEnable(TRUE);
#else
WF_PsPollDisable();
#endif
#endif
WF_CASetBeaconTimeout(MY_DEFAULT_BEACON_TIMEOUT);
#if defined(STACK_USE_UART)
WF_OutputConnectionInfo(&AppConfig);
#endif
WF_CMConnect(ConnectionProfileID);
}
