void main(void)
{
RCC_HSECLKInit();
WatchDogOn();
SysInit();
BootProc();
}
void main(void) {
uint8_t result;
uint8_t timeout;
OSCCON=0xFF; //16 MHz
ANSELA=0;
ANSELC=0;
nWPUEN=1;
#ifdef _1LCD
LCDInit();
LCDCommand(0x01);
#endif
#ifdef DEBUG_HILOCNT
uint8_t low1,low2,low3;
uint8_t high1,high2,high3;
uint8_t i,j;
for (;;) {
low1=low2=low3=0;
high1=high2=high3=0;
for (uint8_t i=1; i<7; i++) {
CLRWDT();
SetMode(i);
if (adc1<10) low1++;
if (adc2<10) low2++;
if (adc3<10) low3++;
if (adc1>245) high1++;
if (adc2>245) high2++;
if (adc3>245) high3++;
}
CLRWDT();
SetLed(0); for (j=0; j<100; j++) __delay_ms(10);
CLRWDT();
if (low1==0) low1=9;
SetLed(low1); __delay_ms(10);
CLRWDT();
SetLed(0); for (j=0; j<30; j++) __delay_ms(10);
CLRWDT();
if (low2==0) low2=9;
SetLed(low2); __delay_ms(10);
CLRWDT();
SetLed(0); for (j=0; j<30; j++) __delay_ms(10);
CLRWDT();
if (low3==0) low3=9;
SetLed(low3); __delay_ms(10);
CLRWDT();
SetLed(0); for (j=0; j<30; j++) __delay_ms(10);
CLRWDT();
if (high1==0) high1=9;
SetLed(high1); __delay_ms(10);
CLRWDT();
SetLed(0); for (j=0; j<30; j++) __delay_ms(10);
CLRWDT();
if (high2==0) high2=9;
SetLed(high2); __delay_ms(10);
CLRWDT();
SetLed(0); for (j=0; j<30; j++) __delay_ms(10);
CLRWDT();
if (high3==0) high3=9;
SetLed(high3); __delay_ms(10);
CLRWDT();
SetLed(0); for (j=0; j<30; j++) __delay_ms(10);
CLRWDT();
}
#endif
// Loop here forever - or at least until we timeout and go into
// permanent low-power sleep that can only be awakened by a reset
timeout=TIMEOUT;
for (;;) {
// VREGPM=0; // Fast wakeup
CLRWDT();
WatchDogOn();
// Try to identify the connected transistor
result=Measure();
CLRWDT();
// If no transistor is found just briefly flash the power-on LED
if (result==RES_NONE) {
SetLed(LED_PWR);
} else {
// We have identified a transisor type and pinout, so flash the
// right LEDs and also reset the timeout
timeout=TIMEOUT;
if (result&RES_NPN) SetLed(LED_NPN);
if (result&RES_PNP) SetLed(LED_PNP);
if (result&RES_NCH) SetLed(LED_NCH);
__delay_ms(5);
SetLed(result&0x0f);
if (result&RES_NCH) {
__delay_ms(5);
SetLed(LED_PWR);
}
}
__delay_ms(5);
SetLed(LED_OFF);
// Check if it's time to shut down and go into a deep sleep
// that will only be awakened by pressing the Reset/Power button
if (--timeout==0) Shutdown();
// Sleep for a few hundred mS to conserve power and then wake up by the watchdog
// and make a new measurement
CLRWDT();
SLEEP();
}
}