void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
u32 val;
AGESAWRAPPER(amdinitmmio);
hudson_lpc_port80();
if (!cpu_init_detectedx && boot_cpu()) {
post_code(0x30);
post_code(0x31);
console_init();
}
/* Halt if there was a built in self test failure */
post_code(0x34);
report_bist_failure(bist);
/* Load MPB */
val = cpuid_eax(1);
printk(BIOS_DEBUG, "BSP Family_Model: %08x \n", val);
printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx \n", cpu_init_detectedx);
post_code(0x37);
AGESAWRAPPER(amdinitreset);
post_code(0x39);
AGESAWRAPPER(amdinitearly);
int s3resume = acpi_is_wakeup_early() && acpi_s3_resume_allowed();
if (!s3resume) {
post_code(0x40);
AGESAWRAPPER(amdinitpost);
post_code(0x41);
AGESAWRAPPER(amdinitenv);
disable_cache_as_ram();
} else { /* S3 detect */
printk(BIOS_INFO, "S3 detected\n");
post_code(0x60);
AGESAWRAPPER(amdinitresume);
AGESAWRAPPER(amds3laterestore);
post_code(0x61);
prepare_for_resume();
}
post_code(0x50);
copy_and_run();
post_code(0x54); /* Should never see this post code. */
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
u32 val;
#if CONFIG_HAVE_ACPI_RESUME
void *resume_backup_memory;
#endif
/*
* All cores: allow caching of flash chip code and data
* (there are no cache-as-ram reliability concerns with family 14h)
*/
__writemsr (0x20c, (0x0100000000ull - CONFIG_ROM_SIZE) | 5);
__writemsr (0x20d, (0x1000000000ull - CONFIG_ROM_SIZE) | 0x800);
/* All cores: set pstate 0 (1600 MHz) early to save a few ms of boot time */
__writemsr (0xc0010062, 0);
if (!cpu_init_detectedx && boot_cpu()) {
post_code(0x30);
sb_Poweron_Init();
post_code(0x31);
smscsuperio_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
console_init();
}
/* Halt if there was a built in self test failure */
post_code(0x34);
report_bist_failure(bist);
/* Load MPB */
val = cpuid_eax(1);
printk(BIOS_DEBUG, "BSP Family_Model: %08x \n", val);
printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx \n", cpu_init_detectedx);
post_code(0x35);
printk(BIOS_DEBUG, "agesawrapper_amdinitmmio ");
val = agesawrapper_amdinitmmio();
if (val)
printk(BIOS_DEBUG, "error level: %x \n", val);
else
printk(BIOS_DEBUG, "passed.\n");
post_code(0x37);
printk(BIOS_DEBUG, "agesawrapper_amdinitreset ");
val = agesawrapper_amdinitreset();
if (val)
printk(BIOS_DEBUG, "error level: %x \n", val);
else
printk(BIOS_DEBUG, "passed.\n");
post_code(0x39);
printk(BIOS_DEBUG, "agesawrapper_amdinitearly ");
val = agesawrapper_amdinitearly ();
if (val)
printk(BIOS_DEBUG, "error level: %x \n", val);
else
printk(BIOS_DEBUG, "passed.\n");
#if CONFIG_HAVE_ACPI_RESUME
if (!acpi_is_wakeup_early()) { /* Check for S3 resume */
#endif
post_code(0x40);
printk(BIOS_DEBUG, "agesawrapper_amdinitpost ");
val = agesawrapper_amdinitpost ();
/* Reboots with outb(3,0x92), outb(4,0xcf9) or triple-fault all
* hang, looks like DRAM re-init goes wrong, don't know why. */
if (val == 7) /* fatal, amdinitenv below is going to hang */
outb(0x06, 0x0cf9); /* reset system harder instead */
if (val)
printk(BIOS_DEBUG, "error level: %x \n", val);
else
printk(BIOS_DEBUG, "passed.\n");
post_code(0x42);
printk(BIOS_DEBUG, "agesawrapper_amdinitenv ");
val = agesawrapper_amdinitenv ();
if (val)
printk(BIOS_DEBUG, "error level: %x \n", val);
else
printk(BIOS_DEBUG, "passed.\n");
#if CONFIG_HAVE_ACPI_RESUME
} else { /* S3 detect */
printk(BIOS_INFO, "S3 detected\n");
post_code(0x60);
printk(BIOS_DEBUG, "agesawrapper_amdinitresume ");
val = agesawrapper_amdinitresume();
if (val)
printk(BIOS_DEBUG, "error level: %x \n", val);
else
printk(BIOS_DEBUG, "passed.\n");
printk(BIOS_DEBUG, "agesawrapper_amds3laterestore ");
val = agesawrapper_amds3laterestore ();
if (val)
printk(BIOS_DEBUG, "error level: %x \n", val);
else
printk(BIOS_DEBUG, "passed.\n");
post_code(0x61);
printk(BIOS_DEBUG, "Find resume memory location\n");
resume_backup_memory = backup_resume();
post_code(0x62);
printk(BIOS_DEBUG, "Move CAR stack.\n");
move_stack_high_mem();
printk(BIOS_DEBUG, "stack moved to: 0x%x\n", (u32) (resume_backup_memory + HIGH_MEMORY_SAVE));
post_code(0x63);
disable_cache_as_ram();
printk(BIOS_DEBUG, "CAR disabled.\n");
set_resume_cache();
/*
* Copy the system memory that is in the ramstage area to the
* reserved area.
*/
if (resume_backup_memory)
memcpy(resume_backup_memory, (void *)(CONFIG_RAMBASE), HIGH_MEMORY_SAVE);
printk(BIOS_DEBUG, "System memory saved. OK to load ramstage.\n");
}
#endif
/* Initialize i8259 pic */
post_code(0x43);
setup_i8259 ();
/* Initialize i8254 timers */
post_code(0x44);
setup_i8254 ();
post_code(0x50);
copy_and_run(0);
printk(BIOS_ERR, "Error: copy_and_run() returned!\n");
post_code(0x54); /* Should never see this post code. */
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
u32 val;
#if CONFIG_HAVE_ACPI_RESUME
void *resume_backup_memory;
#endif
/* In Hudson RRG, PMIOxD2[5:4] is "Drive strength control for
* LpcClk[1:0]". To be consistent with Parmer, setting to 4mA
* even though the register is not documented in the Kabini BKDG.
* Otherwise the serial output is bad code.
*/
outb(0xD2, 0xcd6);
outb(0x00, 0xcd7);
val = agesawrapper_amdinitmmio();
hudson_lpc_port80();
if (!cpu_init_detectedx && boot_cpu()) {
post_code(0x30);
post_code(0x31);
console_init();
}
/* Halt if there was a built in self test failure */
post_code(0x34);
report_bist_failure(bist);
/* Load MPB */
val = cpuid_eax(1);
printk(BIOS_DEBUG, "BSP Family_Model: %08x \n", val);
printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx \n", cpu_init_detectedx);
/* On Larne, after LpcClkDrvSth is set, it needs some time to be stable, because of the buffer ICS551M */
int i;
for(i = 0; i < 200000; i++)
val = inb(0xcd6);
post_code(0x37);
val = agesawrapper_amdinitreset();
if(val) {
printk(BIOS_DEBUG, "agesawrapper_amdinitreset failed: %x \n", val);
}
post_code(0x38);
printk(BIOS_DEBUG, "Got past yangtze_early_setup\n");
post_code(0x39);
val = agesawrapper_amdinitearly ();
if(val) {
printk(BIOS_DEBUG, "agesawrapper_amdinitearly failed: %x \n", val);
}
printk(BIOS_DEBUG, "Got past agesawrapper_amdinitearly\n");
#if CONFIG_HAVE_ACPI_RESUME
if (!acpi_is_wakeup_early()) { /* Check for S3 resume */
#endif
post_code(0x40);
val = agesawrapper_amdinitpost ();
if(val) {
printk(BIOS_DEBUG, "agesawrapper_amdinitpost failed: %x \n", val);
}
printk(BIOS_DEBUG, "Got past agesawrapper_amdinitpost\n");
post_code(0x41);
val = agesawrapper_amdinitenv ();
if(val) {
printk(BIOS_DEBUG, "agesawrapper_amdinitenv failed: %x \n", val);
}
printk(BIOS_DEBUG, "Got past agesawrapper_amdinitenv\n");
/* TODO: Disable cache is not ok. */
disable_cache_as_ram();
#if CONFIG_HAVE_ACPI_RESUME
} else { /* S3 detect */
printk(BIOS_INFO, "S3 detected\n");
post_code(0x60);
printk(BIOS_DEBUG, "agesawrapper_amdinitresume ");
val = agesawrapper_amdinitresume();
if (val)
printk(BIOS_DEBUG, "error level: %x \n", val);
else
printk(BIOS_DEBUG, "passed.\n");
printk(BIOS_DEBUG, "agesawrapper_amds3laterestore ");
val = agesawrapper_amds3laterestore ();
if (val)
printk(BIOS_DEBUG, "error level: %x \n", val);
else
printk(BIOS_DEBUG, "passed.\n");
post_code(0x61);
printk(BIOS_DEBUG, "Find resume memory location\n");
resume_backup_memory = (void *)backup_resume();
post_code(0x62);
printk(BIOS_DEBUG, "Move CAR stack.\n");
move_stack_high_mem();
printk(BIOS_DEBUG, "stack moved to: 0x%x\n", (u32) (resume_backup_memory + HIGH_MEMORY_SAVE));
post_code(0x63);
disable_cache_as_ram();
printk(BIOS_DEBUG, "CAR disabled.\n");
set_resume_cache();
/*
* Copy the system memory that is in the ramstage area to the
* reserved area.
*/
if (resume_backup_memory)
memcpy(resume_backup_memory, (void *)(CONFIG_RAMBASE), HIGH_MEMORY_SAVE);
printk(BIOS_DEBUG, "System memory saved. OK to load ramstage.\n");
}
#endif
outb(0xEA, 0xCD6);
outb(0x1, 0xcd7);
post_code(0x50);
copy_and_run();
post_code(0x54); /* Should never see this post code. */
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
u32 val;
u8 byte;
device_t dev;
AGESAWRAPPER(amdinitmmio);
hudson_lpc_port80();
//__asm__ volatile ("1: jmp 1b");
/* TODO: */
dev = PCI_DEV(0, 0x14, 3);//pci_locate_device(PCI_ID(0x1002, 0x439D), 0);
byte = pci_read_config8(dev, 0x48);
byte |= 3; /* 2e, 2f */
pci_write_config8(dev, 0x48, byte);
if (!cpu_init_detectedx && boot_cpu()) {
post_code(0x30);
post_code(0x31);
lpc47n217_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
outb(0x24, 0xcd6);
outb(0x1, 0xcd7);
outb(0xea, 0xcd6);
outb(0x1, 0xcd7);
*(u8 *)0xfed80101 = 0x98;
console_init();
}
/* Halt if there was a built in self test failure */
post_code(0x34);
report_bist_failure(bist);
/* Load MPB */
val = cpuid_eax(1);
printk(BIOS_DEBUG, "BSP Family_Model: %08x \n", val);
printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx \n", cpu_init_detectedx);
post_code(0x37);
AGESAWRAPPER(amdinitreset);
post_code(0x39);
AGESAWRAPPER(amdinitearly);
int s3resume = acpi_is_wakeup_early() && acpi_s3_resume_allowed();
if (!s3resume) {
post_code(0x40);
AGESAWRAPPER(amdinitpost);
post_code(0x41);
AGESAWRAPPER(amdinitenv);
disable_cache_as_ram();
} else { /* S3 detect */
printk(BIOS_INFO, "S3 detected\n");
post_code(0x60);
AGESAWRAPPER(amdinitresume);
AGESAWRAPPER(amds3laterestore);
post_code(0x61);
prepare_for_resume();
}
post_code(0x50);
copy_and_run();
post_code(0x54); /* Should never see this post code. */
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
u32 val;
u8 byte;
device_t dev;
#if IS_ENABLED(CONFIG_POST_DEVICE_PCI_PCIE)
hudson_pci_port80();
#endif
#if IS_ENABLED(CONFIG_POST_DEVICE_LPC)
hudson_lpc_port80();
#endif
val = agesawrapper_amdinitmmio();
if (!cpu_init_detectedx && boot_cpu()) {
/* enable SIO LPC decode */
dev = PCI_DEV(0, 0x14, 3);
byte = pci_read_config8(dev, 0x48);
byte |= 3; /* 2e, 2f */
pci_write_config8(dev, 0x48, byte);
/* enable serial decode */
byte = pci_read_config8(dev, 0x44);
byte |= (1 << 6); /* 0x3f8 */
pci_write_config8(dev, 0x44, byte);
post_code(0x30);
/* enable SB MMIO space */
outb(0x24, 0xcd6);
outb(0x1, 0xcd7);
/* enable SIO clock */
sbxxx_enable_48mhzout();
ite_kill_watchdog(GPIO_DEV);
ite_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
ite_enable_3vsbsw(GPIO_DEV);
console_init();
/* turn on secondary smbus at b20 */
outb(0x28, 0xcd6);
byte = inb(0xcd7);
byte |= 1;
outb(byte, 0xcd7);
/* set DDR3 voltage */
byte = CONFIG_BOARD_ASUS_F2A85_M_DDR3_VOLT_VAL;
/* default is byte = 0x0, so no need to set it in this case */
if (byte)
do_smbus_write_byte(0xb20, 0x15, 0x3, byte);
}
/* Halt if there was a built in self test failure */
post_code(0x34);
report_bist_failure(bist);
/* Load MPB */
val = cpuid_eax(1);
printk(BIOS_DEBUG, "BSP Family_Model: %08x \n", val);
printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx \n", cpu_init_detectedx);
post_code(0x37);
printk(BIOS_DEBUG, "agesawrapper_amdinitreset ");
val = agesawrapper_amdinitreset();
if(val) {
printk(BIOS_DEBUG, "agesawrapper_amdinitreset failed: %x \n", val);
}
post_code(0x39);
val = agesawrapper_amdinitearly ();
if(val) {
printk(BIOS_DEBUG, "agesawrapper_amdinitearly failed: %x \n", val);
}
printk(BIOS_DEBUG, "Got past agesawrapper_amdinitearly\n");
int s3resume = acpi_is_wakeup_early() && acpi_s3_resume_allowed();
if (!s3resume) {
post_code(0x40);
val = agesawrapper_amdinitpost ();
if(val) {
printk(BIOS_DEBUG, "agesawrapper_amdinitpost failed: %x \n", val);
}
printk(BIOS_DEBUG, "Got past agesawrapper_amdinitpost\n");
post_code(0x41);
val = agesawrapper_amdinitenv ();
if(val) {
printk(BIOS_DEBUG, "agesawrapper_amdinitenv failed: %x \n", val);
}
printk(BIOS_DEBUG, "Got past agesawrapper_amdinitenv\n");
disable_cache_as_ram();
} else { /* S3 detect */
printk(BIOS_INFO, "S3 detected\n");
post_code(0x60);
printk(BIOS_DEBUG, "agesawrapper_amdinitresume ");
val = agesawrapper_amdinitresume();
if (val)
printk(BIOS_DEBUG, "error level: %x \n", val);
else
printk(BIOS_DEBUG, "passed.\n");
printk(BIOS_DEBUG, "agesawrapper_amds3laterestore ");
val = agesawrapper_amds3laterestore ();
if (val)
printk(BIOS_DEBUG, "error level: %x \n", val);
else
printk(BIOS_DEBUG, "passed.\n");
post_code(0x61);
prepare_for_resume();
}
post_code(0x50);
copy_and_run();
post_code(0x54); /* Should never see this post code. */
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
u32 val;
/* In Hudson RRG, PMIOxD2[5:4] is "Drive strength control for
* LpcClk[1:0]". To be consistent with Parmer, setting to 4mA
* even though the register is not documented in the Kabini BKDG.
* Otherwise the serial output is bad code.
*/
outb(0xD2, 0xcd6);
outb(0x00, 0xcd7);
AGESAWRAPPER(amdinitmmio);
hudson_lpc_port80();
if (!cpu_init_detectedx && boot_cpu()) {
post_code(0x30);
post_code(0x31);
console_init();
}
/* Halt if there was a built in self test failure */
post_code(0x34);
report_bist_failure(bist);
/* Load MPB */
val = cpuid_eax(1);
printk(BIOS_DEBUG, "BSP Family_Model: %08x \n", val);
printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx \n", cpu_init_detectedx);
/* On Larne, after LpcClkDrvSth is set, it needs some time to be stable, because of the buffer ICS551M */
int i;
for(i = 0; i < 200000; i++)
val = inb(0xcd6);
post_code(0x37);
AGESAWRAPPER(amdinitreset);
post_code(0x38);
printk(BIOS_DEBUG, "Got past yangtze_early_setup\n");
post_code(0x39);
AGESAWRAPPER(amdinitearly);
int s3resume = acpi_is_wakeup_early() && acpi_s3_resume_allowed();
if (!s3resume) {
post_code(0x40);
AGESAWRAPPER(amdinitpost);
post_code(0x41);
AGESAWRAPPER(amdinitenv);
/* TODO: Disable cache is not ok. */
disable_cache_as_ram();
} else { /* S3 detect */
printk(BIOS_INFO, "S3 detected\n");
post_code(0x60);
AGESAWRAPPER(amdinitresume);
AGESAWRAPPER(amds3laterestore);
post_code(0x61);
prepare_for_resume();
}
outb(0xEA, 0xCD6);
outb(0x1, 0xcd7);
post_code(0x50);
copy_and_run();
post_code(0x54); /* Should never see this post code. */
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
u32 val;
/*
* All cores: allow caching of flash chip code and data
* (there are no cache-as-ram reliability concerns with family 14h)
*/
__writemsr (0x20c, (0x0100000000ull - CACHE_ROM_SIZE) | 5);
__writemsr (0x20d, (0x1000000000ull - CACHE_ROM_SIZE) | 0x800);
/* All cores: set pstate 0 (1600 MHz) early to save a few ms of boot time */
__writemsr (0xc0010062, 0);
if (!cpu_init_detectedx && boot_cpu()) {
post_code(0x30);
sb_Poweron_Init();
post_code(0x31);
fintek_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
console_init();
}
/* Halt if there was a built in self test failure */
post_code(0x34);
report_bist_failure(bist);
/* Load MPB */
val = cpuid_eax(1);
printk(BIOS_DEBUG, "BSP Family_Model: %08x\n", val);
printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx\n", cpu_init_detectedx);
post_code(0x35);
AGESAWRAPPER(amdinitmmio);
post_code(0x37);
AGESAWRAPPER(amdinitreset);
post_code(0x39);
AGESAWRAPPER(amdinitearly);
int s3resume = acpi_is_wakeup_early() && acpi_s3_resume_allowed();
if (!s3resume) {
post_code(0x40);
AGESAWRAPPER(amdinitpost);
post_code(0x42);
AGESAWRAPPER(amdinitenv);
} else { /* S3 detect */
printk(BIOS_INFO, "S3 detected\n");
post_code(0x60);
AGESAWRAPPER(amdinitresume);
AGESAWRAPPER(amds3laterestore);
post_code(0x61);
prepare_for_resume();
}
post_code(0x50);
copy_and_run();
printk(BIOS_ERR, "Error: copy_and_run() returned!\n");
post_code(0x54); /* Should never see this post code. */
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
u32 val;
u8 byte;
device_t dev;
#if IS_ENABLED(CONFIG_POST_DEVICE_PCI_PCIE)
hudson_pci_port80();
#endif
#if IS_ENABLED(CONFIG_POST_DEVICE_LPC)
hudson_lpc_port80();
#endif
#if CONFIG_HAVE_ACPI_RESUME
void *resume_backup_memory;
#endif
val = agesawrapper_amdinitmmio();
if (!cpu_init_detectedx && boot_cpu()) {
/* enable SIO LPC decode */
dev = PCI_DEV(0, 0x14, 3);
byte = pci_read_config8(dev, 0x48);
byte |= 3; /* 2e, 2f */
pci_write_config8(dev, 0x48, byte);
/* enable serial decode */
byte = pci_read_config8(dev, 0x44);
byte |= (1 << 6); /* 0x3f8 */
pci_write_config8(dev, 0x44, byte);
post_code(0x30);
/* enable SB MMIO space */
outb(0x24, 0xcd6);
outb(0x1, 0xcd7);
/* enable SIO clock */
sbxxx_enable_48mhzout();
ite_kill_watchdog(GPIO_DEV);
ite_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
ite_enable_3vsbsw(GPIO_DEV);
console_init();
/* turn on secondary smbus at b20 */
outb(0x28, 0xcd6);
byte = inb(0xcd7);
byte |= 1;
outb(byte, 0xcd7);
/* set DDR3 voltage */
byte = CONFIG_BOARD_ASUS_F2A85_M_DDR3_VOLT_VAL;
/* default is byte = 0x0, so no need to set it in this case */
if (byte)
do_smbus_write_byte(0xb20, 0x15, 0x3, byte);
}
/* Halt if there was a built in self test failure */
post_code(0x34);
report_bist_failure(bist);
/* Load MPB */
val = cpuid_eax(1);
printk(BIOS_DEBUG, "BSP Family_Model: %08x \n", val);
printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx \n", cpu_init_detectedx);
post_code(0x37);
printk(BIOS_DEBUG, "agesawrapper_amdinitreset ");
val = agesawrapper_amdinitreset();
if(val) {
printk(BIOS_DEBUG, "agesawrapper_amdinitreset failed: %x \n", val);
}
post_code(0x39);
val = agesawrapper_amdinitearly ();
if(val) {
printk(BIOS_DEBUG, "agesawrapper_amdinitearly failed: %x \n", val);
}
printk(BIOS_DEBUG, "Got past agesawrapper_amdinitearly\n");
#if CONFIG_HAVE_ACPI_RESUME
if (!acpi_is_wakeup_early()) { /* Check for S3 resume */
#endif
post_code(0x40);
val = agesawrapper_amdinitpost ();
if(val) {
printk(BIOS_DEBUG, "agesawrapper_amdinitpost failed: %x \n", val);
}
printk(BIOS_DEBUG, "Got past agesawrapper_amdinitpost\n");
post_code(0x41);
val = agesawrapper_amdinitenv ();
if(val) {
printk(BIOS_DEBUG, "agesawrapper_amdinitenv failed: %x \n", val);
}
printk(BIOS_DEBUG, "Got past agesawrapper_amdinitenv\n");
disable_cache_as_ram();
#if CONFIG_HAVE_ACPI_RESUME
} else { /* S3 detect */
printk(BIOS_INFO, "S3 detected\n");
post_code(0x60);
printk(BIOS_DEBUG, "agesawrapper_amdinitresume ");
val = agesawrapper_amdinitresume();
if (val)
printk(BIOS_DEBUG, "error level: %x \n", val);
else
printk(BIOS_DEBUG, "passed.\n");
printk(BIOS_DEBUG, "agesawrapper_amds3laterestore ");
val = agesawrapper_amds3laterestore ();
if (val)
printk(BIOS_DEBUG, "error level: %x \n", val);
else
printk(BIOS_DEBUG, "passed.\n");
post_code(0x61);
printk(BIOS_DEBUG, "Find resume memory location\n");
resume_backup_memory = (void *)backup_resume();
post_code(0x62);
printk(BIOS_DEBUG, "Move CAR stack.\n");
move_stack_high_mem();
printk(BIOS_DEBUG, "stack moved to: 0x%x\n", (u32) (resume_backup_memory + HIGH_MEMORY_SAVE));
post_code(0x63);
disable_cache_as_ram();
printk(BIOS_DEBUG, "CAR disabled.\n");
set_resume_cache();
/*
* Copy the system memory that is in the ramstage area to the
* reserved area.
*/
if (resume_backup_memory)
memcpy(resume_backup_memory, (void *)(CONFIG_RAMBASE), HIGH_MEMORY_SAVE);
printk(BIOS_DEBUG, "System memory saved. OK to load ramstage.\n");
}
#endif
post_code(0x50);
copy_and_run();
post_code(0x54); /* Should never see this post code. */
}