/**
* \brief Start ADC sample.
* Initialize ADC, set clock and timing, and set ADC to given mode.
*/
static void start_adc(void)
{
struct adc_config adc_cfg = {
/* System clock division factor is 16 */
.prescal = ADC_PRESCAL_DIV16,
/* The APB clock is used */
.clksel = ADC_CLKSEL_APBCLK,
/* Max speed is 150K */
.speed = ADC_SPEED_150K,
/* ADC Reference voltage is 0.625*VCC */
.refsel = ADC_REFSEL_1,
/* Enables the Startup time */
.start_up = CONFIG_ADC_STARTUP
};
struct adc_seq_config adc_seq_cfg = {
/* Select Vref for shift cycle */
.zoomrange = ADC_ZOOMRANGE_0,
/* Pad Ground */
.muxneg = ADC_MUXNEG_1,
/* DAC internal */
.muxpos = ADC_MUXPOS_3,
/* Enables the internal voltage sources */
.internal = ADC_INTERNAL_3,
/* Disables the ADC gain error reduction */
.gcomp = ADC_GCOMP_DIS,
/* Disables the HWLA mode */
.hwla = ADC_HWLA_DIS,
/* 12-bits resolution */
.res = ADC_RES_12_BIT,
/* Enables the single-ended mode */
.bipolar = ADC_BIPOLAR_SINGLEENDED
};
struct adc_ch_config adc_ch_cfg = {
.seq_cfg = &adc_seq_cfg,
/* Internal Timer Max Counter */
.internal_timer_max_count = 60,
/* Window monitor mode is off */
.window_mode = 0,
.low_threshold = 0,
.high_threshold = 0,
};
if(adc_init(&g_adc_inst, ADCIFE, &adc_cfg) != STATUS_OK) {
puts("-F- ADC Init Fail!\n\r");
while(1);
}
if(adc_enable(&g_adc_inst) != STATUS_OK) {
puts("-F- ADC Enable Fail!\n\r");
while(1);
}
if (g_adc_test_mode.uc_pdc_en) {
adc_disable_interrupt(&g_adc_inst, ADC_SEQ_SEOC);
adc_pdca_set_config(&g_adc_pdca_cfg);
pdca_channel_set_callback(CONFIG_ADC_PDCA_RX_CHANNEL, pdca_transfer_done,
PDCA_0_IRQn, 1, PDCA_IER_TRC);
} else {
pdca_channel_disable_interrupt(CONFIG_ADC_PDCA_RX_CHANNEL,
PDCA_IDR_TRC);
pdca_channel_disable_interrupt(CONFIG_ADC_PDCA_TX_CHANNEL,
PDCA_IDR_TRC);
adc_ch_set_config(&g_adc_inst, &adc_ch_cfg);
adc_set_callback(&g_adc_inst, ADC_SEQ_SEOC, adcife_read_conv_result,
ADCIFE_IRQn, 1);
}
/* Configure trigger mode and start convention. */
switch (g_adc_test_mode.uc_trigger_mode) {
case TRIGGER_MODE_SOFTWARE:
adc_configure_trigger(&g_adc_inst, ADC_TRIG_SW);
break;
case TRIGGER_MODE_CON:
adc_configure_trigger(&g_adc_inst, ADC_TRIG_CON);
break;
case TRIGGER_MODE_ITIMER:
adc_configure_trigger(&g_adc_inst, ADC_TRIG_INTL_TIMER);
adc_configure_itimer_period(&g_adc_inst,
adc_ch_cfg.internal_timer_max_count);
adc_start_itimer(&g_adc_inst);
break;
default:
break;
}
if (g_adc_test_mode.uc_gain_en) {
adc_configure_gain(&g_adc_inst, ADC_GAIN_2X);
} else {
adc_configure_gain(&g_adc_inst, ADC_GAIN_1X);
}
}
/**
* \brief Start DAC ouput.
* Initialize DAC, set clock and timing, and set DAC to given mode.
*/
static void start_dac(void)
{
sysclk_enable_peripheral_clock(DACC);
/* Reset DACC registers */
dacc_reset(DACC);
/* Half word transfer mode */
dacc_set_transfer_mode(DACC, 0);
/* Timing:
* startup - 0x10 (17 clocks)
* internal trigger clock - 0x60 (96 clocks)
*/
dacc_set_timing(DACC, 0x10, 0x60);
/* Enable DAC */
dacc_enable(DACC);
/* The DAC is 10-bit resolution, so output voltage should be
* (3300 * 255) / ((1 << 10) - 1) = 823mv */
dacc_write_conversion_data(DACC, 0xFF);
}
/**
* \brief Test ADCIFE in Differential mode.
*
* \param test Current test case.
*/
static void run_adcife_diff_test(const struct test_case *test)
{
uint32_t timeout = ADC_NUM_OF_ATTEMPTS;
bool conversion_timeout = false;
struct adc_seq_config adc_seq_cfg = {
/* Select Vref for shift cycle */
.zoomrange = ADC_ZOOMRANGE_0,
/* Pad Ground */
.muxneg = ADC_MUXNEG_1,
/* Scaled Vcc, Vcc/10 */
.muxpos = ADC_MUXPOS_2,
/* Enables the internal voltage sources */
.internal = ADC_INTERNAL_3,
/* Disables the ADC gain error reduction */
.gcomp = ADC_GCOMP_DIS,
/* Disables the HWLA mode */
.hwla = ADC_HWLA_DIS,
/* 12-bits resolution */
.res = ADC_RES_12_BIT,
/* Enables the differential mode */
.bipolar = ADC_BIPOLAR_DIFFERENTIAL
};
struct adc_ch_config adc_ch_cfg = {
.seq_cfg = &adc_seq_cfg,
/* Internal Timer Max Counter */
.internal_timer_max_count = 60,
/* Window monitor mode is off */
.window_mode = 0,
.low_threshold = 0,
.high_threshold = 0,
};
adc_ch_set_config(&g_adc_inst, &adc_ch_cfg);
adc_configure_trigger(&g_adc_inst, ADC_TRIG_CON);
adc_configure_gain(&g_adc_inst, ADC_GAIN_1X);
while (!((adc_get_status(&g_adc_inst) & ADCIFE_SR_SEOC) ==
ADCIFE_SR_SEOC)) {
if (!timeout--) {
conversion_timeout = true;
}
}
test_assert_true(test, conversion_timeout == false, "ADCIFE Differential conversion timeout");
/* Because selected channel is positive input, then in differential mode
* the output conversion result will = 2047 + (Vin/Vref)*2047.
*/
test_assert_true(test, adc_get_last_conv_value(&g_adc_inst) > 2047,
"ADCIFE Differential test failed");
}
/**
* \brief Test ADCIFE in internal timer trigger mode,
* which also tests interrupt driven conversions.
*
* \param test Current test case.
*/
static void run_adcife_itimer_trig_test(const struct test_case *test)
{
struct adc_seq_config adc_seq_cfg = {
/* Select Vref for shift cycle */
.zoomrange = ADC_ZOOMRANGE_0,
/* Pad Ground */
.muxneg = ADC_MUXNEG_1,
/* Scaled Vcc, Vcc/10 */
.muxpos = ADC_MUXPOS_2,
/* Enables the internal voltage sources */
.internal = ADC_INTERNAL_3,
/* Disables the ADC gain error reduction */
.gcomp = ADC_GCOMP_DIS,
/* Disables the HWLA mode */
.hwla = ADC_HWLA_DIS,
/* 12-bits resolution */
.res = ADC_RES_12_BIT,
/* Enables the single-ended mode */
.bipolar = ADC_BIPOLAR_SINGLEENDED
};
struct adc_ch_config adc_ch_cfg = {
.seq_cfg = &adc_seq_cfg,
/* Internal Timer Max Counter */
.internal_timer_max_count = 60,
/* Window monitor mode is off */
.window_mode = 0,
.low_threshold = 0,
.high_threshold = 0,
};
adc_ch_set_config(&g_adc_inst, &adc_ch_cfg);
adc_set_callback(&g_adc_inst, ADC_SEQ_SEOC, adcife_set_conv_flag,
ADCIFE_IRQn, 1);
adc_configure_trigger(&g_adc_inst, ADC_TRIG_INTL_TIMER);
adc_configure_gain(&g_adc_inst, ADC_GAIN_1X);
adc_configure_itimer_period(&g_adc_inst,
adc_ch_cfg.internal_timer_max_count);
adc_start_itimer(&g_adc_inst);
delay_ms(100);
test_assert_true(test, g_uc_condone_flag == 1,
"ADCIFE Internal Timer trigger test failed");
}
/* When VDDANA is in MIN value = 2.4V, the equivalent voltage value is
* (2400 * 255) / ((1 << 10) - 1) = 598mv. The relative digital value is
* 598 * 4095 / 1000 = 2449. */
#define DAC_INTERNAL_MIN_VALUE 2449
/* When VDDANA is in MAX value = 3.6V the equivalent voltage value is
* (3600 * 255) / ((1 << 10) - 1) = 897mv. The relative digital value is
* 897 * 4095 / 1000 = 3673. */
#define DAC_INTERNAL_MAX_VALUE 3673
/* When VCC is in MIN value = 1.6V, the equivalent voltage value is
* 1600 / 10 = 160mv. The relative digital value is
* 160 * 4095 / 1000 = 434. */
#define VCC_SCALED_MIN_VALUE 434
/* When VCC is in MAX value = 3.6V, the equivalent voltage value is
* 3600 / 10 = 360mv. The relative digital value is
* 360 * 4095 / 1000 = 1474. */
#define VCC_SCALED_MAX_VALUE 1474
/**
* \brief Test ADCIFE in multiple channel mode.
*
* \param test Current test case.
*/
static void run_adcife_multichannel_test(const struct test_case *test)
{
start_dac();
adc_pdca_set_config(&g_adc_pdca_cfg);
pdca_channel_set_callback(CONFIG_ADC_PDCA_RX_CHANNEL, pdca_transfer_done,
PDCA_0_IRQn, 1, PDCA_IER_TRC);
adc_configure_trigger(&g_adc_inst, ADC_TRIG_CON);
adc_configure_gain(&g_adc_inst, ADC_GAIN_1X);
delay_ms(100);
/* The DAC output voltage value is 823mv, so the equivalent ADC value should be
* 4095 * 823 / 1000 = 3370. The scaled VCC output voltage is 330mv, so the
* equivalent ADC value should be 4095 * 330 / 1000 = 1351. */
test_assert_true(test,
((DAC_INTERNAL_MIN_VALUE < g_adc_sample_data[0] < DAC_INTERNAL_MAX_VALUE)
&& (VCC_SCALED_MIN_VALUE < g_adc_sample_data[1] < VCC_SCALED_MAX_VALUE)),
"ADCIFE Multichannel test failed");
}
/**
* \brief Test ADCIFE in window monitor mode.
*
* \param test Current test case.
*/
static void run_adcife_wm_test(const struct test_case *test)
{
struct adc_seq_config adc_seq_cfg = {
/* Select Vref for shift cycle */
.zoomrange = ADC_ZOOMRANGE_0,
/* Pad Ground */
.muxneg = ADC_MUXNEG_1,
/* Scaled Vcc, Vcc/10 */
.muxpos = ADC_MUXPOS_2,
/* Enables the internal voltage sources */
.internal = ADC_INTERNAL_3,
/* Disables the ADC gain error reduction */
.gcomp = ADC_GCOMP_DIS,
/* Disables the HWLA mode */
.hwla = ADC_HWLA_DIS,
/* 12-bits resolution */
.res = ADC_RES_12_BIT,
/* Enables the single-ended mode */
.bipolar = ADC_BIPOLAR_SINGLEENDED
};
struct adc_ch_config adc_ch_cfg = {
.seq_cfg = &adc_seq_cfg,
/* Internal Timer Max Counter */
.internal_timer_max_count = 60,
/* Window monitor mode is off */
.window_mode = ADC_WM_MODE_3,
/* The equivalent voltage value is 205 * 1000 / 4095 = 50mv. */
.low_threshold = 205,
/* The equivalent voltage value is 2050 * 1000 / 4095 = 500mv. */
.high_threshold = 2050,
};
adc_ch_set_config(&g_adc_inst, &adc_ch_cfg);
adc_configure_trigger(&g_adc_inst, ADC_TRIG_CON);
adc_configure_gain(&g_adc_inst, ADC_GAIN_1X);
adc_set_callback(&g_adc_inst, ADC_WINDOW_MONITOR, adcife_set_wm_flag,
ADCIFE_IRQn, 1);
delay_ms(100);
test_assert_true(test, g_uc_enter_win_flag == 1,
"ADCIFE Inside Window Mode test failed");
/* The teseted channel voltage is outside window */
adc_disable(&g_adc_inst);
g_uc_enter_win_flag = 0;
adc_seq_cfg.muxpos = ADC_MUXPOS_3;
adc_ch_set_config(&g_adc_inst, &adc_ch_cfg);
adc_configure_trigger(&g_adc_inst, ADC_TRIG_CON);
adc_configure_gain(&g_adc_inst, ADC_GAIN_1X);
adc_enable_interrupt(&g_adc_inst, ADC_WINDOW_MONITOR);
delay_ms(100);
test_assert_true(test, g_uc_enter_win_flag == 0,
"ADCIFE Outside Window Mode test failed");
}
/**
* \brief Run ADCIFE driver unit tests.
*/
int main(void)
{
const usart_serial_options_t usart_serial_options = {
.baudrate = CONF_TEST_BAUDRATE,
.charlength = CONF_TEST_CHARLENGTH,
.paritytype = CONF_TEST_PARITY,
.stopbits = CONF_TEST_STOPBITS
};
/* Initialize the system clock and board */
sysclk_init();
board_init();
/* Enable the debug uart */
stdio_serial_init(CONF_TEST_USART, &usart_serial_options);
#if defined(__GNUC__)
setbuf(stdout, NULL);
#endif
/* Define all the test cases */
DEFINE_TEST_CASE(adcife_init_test, NULL, run_adcife_init_test, NULL,
"ADCIFE Initialize test");
DEFINE_TEST_CASE(adcife_diff_test, NULL, run_adcife_diff_test, NULL,
"ADCIFE Differential test");
DEFINE_TEST_CASE(adcife_itmer_trig_test, NULL, run_adcife_itimer_trig_test,
NULL, "ADCIFE Internal Timer trigger test");
DEFINE_TEST_CASE(adcife_multichannel_test, NULL, run_adcife_multichannel_test, NULL,
"ADCIFE Multichannel test");
DEFINE_TEST_CASE(adcife_wm_test, NULL, run_adcife_wm_test,
NULL, "ADCIFE Window Monitor Mode test");
/* Put test case addresses in an array */
DEFINE_TEST_ARRAY(adcife_tests) = {
&adcife_init_test,
&adcife_diff_test,
&adcife_itmer_trig_test,
&adcife_multichannel_test,
&adcife_wm_test,
};
/* Define the test suite */
DEFINE_TEST_SUITE(adcife_suite, adcife_tests,
"SAM ADCIFE driver test suite");
/* Run all tests in the test suite */
test_suite_run(&adcife_suite);
while (1) {
/* Busy-wait forever. */
}
}
/**
* \brief Initialize the temperature sensor
*/
void initialize_temperature(void) {
/** not used at present */
#if 0
struct adc_config adc_cfg = {
/* System clock division factor is 16 */
.prescal = ADC_PRESCAL_DIV16,
/* The APB clock is used */
.clksel = ADC_CLKSEL_APBCLK,
/* Max speed is 150K */
.speed = ADC_SPEED_150K,
/* ADC Reference voltage is VCC/2 */
.refsel =ADC_REFSEL_4,
/* Enables the Startup time */
.start_up = CONFIG_ADC_STARTUP
};
struct adc_seq_config adc_seq_cfg = {
/* Select Vref for shift cycle */
.zoomrange = ADC_ZOOMRANGE_0,
/* Pad Ground */
.muxneg = ADC_MUXNEG_1,
/* Temperature sensor */
.muxpos = EPD_Temperature_Sensor_ADC,
/* Enables the internal voltage sources */
.internal =ADC_INTERNAL_2,
/* Disables the ADC gain error reduction */
.gcomp = ADC_GCOMP_DIS,
/* Disables the HWLA mode */
.hwla = ADC_HWLA_DIS,
.gain=ADC_GAIN_1X,
/* 12-bits resolution */
.res = ADC_RES_12_BIT,
/* Enables the single-ended mode */
.bipolar = ADC_BIPOLAR_SINGLEENDED
};
struct adc_ch_config adc_ch_cfg = {
.seq_cfg = &adc_seq_cfg,
/* Internal Timer Max Counter */
.internal_timer_max_count = 60,
/* Window monitor mode is off */
.window_mode = 0,
.low_threshold = 0,
.high_threshold = 0,
};
adc_init(&g_adc_inst, ADCIFE, &adc_cfg);
adc_enable(&g_adc_inst);
adc_ch_set_config(&g_adc_inst, &adc_ch_cfg);
adc_set_callback(&g_adc_inst, ADC_SEQ_SEOC, adcife_read_conv_result, ADCIFE_IRQn, 1);
adc_configure_trigger(&g_adc_inst,ADC_TRIG_SW);
adc_configure_gain(&g_adc_inst, ADC_GAIN_1X);
#endif
}
/**
* \brief Initialize the EPD hardware setting
*/
void EPD_display_hardware_init (void) {
EPD_initialize_gpio();
EPD_Vcc_turn_off();
epd_spi_init();
initialize_temperature();
EPD_cs_low();
EPD_pwm_low();
EPD_rst_low();
EPD_discharge_low();
EPD_border_low();
//initialize_EPD_timer();
}
/**
* \brief Example entry point.
*
* \return Unused (ANSI-C compatibility).
*/
int main(void)
{
uint8_t c_choice;
int16_t s_adc_value;
int16_t s_dac_value;
int16_t s_threshold = 0;
float f_dac_data;
uint32_t ul_dac_data;
/* Initialize the SAM system. */
sysclk_init();
board_init();
configure_console();
/* Output example information. */
puts(STRING_HEADER);
/* Initialize threshold. */
gs_us_low_threshold = 500;
gs_us_high_threshold = 2000;
struct adc_config adc_cfg = {
/* System clock division factor is 16 */
.prescal = ADC_PRESCAL_DIV16,
/* The APB clock is used */
.clksel = ADC_CLKSEL_APBCLK,
/* Max speed is 150K */
.speed = ADC_SPEED_150K,
/* ADC Reference voltage is 0.625*VCC */
.refsel = ADC_REFSEL_1,
/* Enables the Startup time */
.start_up = CONFIG_ADC_STARTUP
};
struct adc_seq_config adc_seq_cfg = {
/* Select Vref for shift cycle */
.zoomrange = ADC_ZOOMRANGE_0,
/* Pad Ground */
.muxneg = ADC_MUXNEG_1,
/* DAC Internal */
.muxpos = ADC_MUXPOS_3,
/* Enables the internal voltage sources */
.internal = ADC_INTERNAL_3,
/* Disables the ADC gain error reduction */
.gcomp = ADC_GCOMP_DIS,
/* Disables the HWLA mode */
.hwla = ADC_HWLA_DIS,
/* 12-bits resolution */
.res = ADC_RES_12_BIT,
/* Enables the single-ended mode */
.bipolar = ADC_BIPOLAR_SINGLEENDED
};
struct adc_ch_config adc_ch_cfg = {
.seq_cfg = &adc_seq_cfg,
/* Internal Timer Max Counter */
.internal_timer_max_count = 60,
/* Window monitor mode is off */
.window_mode = ADC_WM_MODE_3,
/* The equivalent voltage value is 500 * VOLT_REF / 4095 = 251mv. */
.low_threshold = gs_us_low_threshold,
/* The equivalent voltage value is 2000 * VOLT_REF / 4095 = 1002mv. */
.high_threshold = gs_us_high_threshold,
};
start_dac();
if(adc_init(&g_adc_inst, ADCIFE, &adc_cfg) != STATUS_OK) {
puts("-F- ADC Init Fail!\n\r");
while(1);
}
if(adc_enable(&g_adc_inst) != STATUS_OK) {
puts("-F- ADC Enable Fail!\n\r");
while(1);
}
adc_ch_set_config(&g_adc_inst, &adc_ch_cfg);
adc_configure_trigger(&g_adc_inst, ADC_TRIG_CON);
adc_configure_gain(&g_adc_inst, ADC_GAIN_1X);
adc_set_callback(&g_adc_inst, ADC_WINDOW_MONITOR, adcife_wm_handler,
ADCIFE_IRQn, 1);
/* Display main menu. */
display_menu();
while (1) {
scanf("%c", (char *)&c_choice);
printf("%c\r\n", c_choice);
switch (c_choice) {
case '0':
adc_disable_interrupt(&g_adc_inst, ADC_WINDOW_MONITOR);
printf("DAC output is set to(mv) from 0mv to %dmv: ",
(int32_t)VOLT_REF);
s_dac_value = get_voltage();
puts("\r");
f_dac_data = (float)s_dac_value * DACC_MAX_DATA / VDDANA;
ul_dac_data = f_to_int(f_dac_data);
if (s_dac_value >= 0) {
dacc_write_conversion_data(DACC, ul_dac_data);
}
delay_ms(100);
adc_clear_status(&g_adc_inst, ADCIFE_SCR_WM);
adc_enable_interrupt(&g_adc_inst, ADC_WINDOW_MONITOR);
break;
case '1':
adc_disable_interrupt(&g_adc_inst, ADC_WINDOW_MONITOR);
printf("Low threshold is set to(mv) from 0mv to %dmv: ",
(int32_t)VOLT_REF);
s_threshold = get_voltage();
puts("\r");
if (s_threshold >= 0) {
s_adc_value = s_threshold * MAX_DIGITAL /
VOLT_REF;
adc_configure_wm_threshold(&g_adc_inst,
s_adc_value,
gs_us_high_threshold);
/* Renew low threshold. */
gs_us_low_threshold = s_adc_value;
float f_low_threshold =
(float)gs_us_low_threshold *
VOLT_REF / MAX_DIGITAL;
uint32_t ul_low_threshold =
f_to_int(f_low_threshold);
printf("Setting low threshold to %u mv (reg value to 0x%x ~%d%%)\n\r",
ul_low_threshold, gs_us_low_threshold,
gs_us_low_threshold * 100 / MAX_DIGITAL);
}
adc_clear_status(&g_adc_inst, ADCIFE_SCR_WM);
adc_enable_interrupt(&g_adc_inst, ADC_WINDOW_MONITOR);
break;
case '2':
adc_disable_interrupt(&g_adc_inst, ADC_WINDOW_MONITOR);
printf("High threshold is set to(mv)from 0mv to %dmv:",
(int32_t)VOLT_REF);
s_threshold = get_voltage();
puts("\r");
if (s_threshold >= 0) {
s_adc_value = s_threshold * MAX_DIGITAL /
VOLT_REF;
adc_configure_wm_threshold(&g_adc_inst,
gs_us_low_threshold,
s_adc_value);
/* Renew high threshold. */
gs_us_high_threshold = s_adc_value;
float f_high_threshold =
(float)gs_us_high_threshold *
VOLT_REF / MAX_DIGITAL;
uint32_t ul_high_threshold =
f_to_int(f_high_threshold);
printf("Setting high threshold to %u mv (reg value to 0x%x ~%d%%)\n\r",
ul_high_threshold, gs_us_high_threshold,
gs_us_high_threshold * 100 / MAX_DIGITAL);
}
adc_clear_status(&g_adc_inst, ADCIFE_SCR_WM);
adc_enable_interrupt(&g_adc_inst, ADC_WINDOW_MONITOR);
break;
case '3':
adc_disable_interrupt(&g_adc_inst, ADC_WINDOW_MONITOR);
puts("-a. Above low threshold.\n\r"
"-b. Below high threshold.\n\r"
"-c. In the comparison window.\n\r"
"-d. Out of the comparison window.\n\r"
"-q. Quit the setting.\r");
c_choice = get_wm_mode();
adc_configure_wm_mode(&g_adc_inst, c_choice);
printf("Comparison mode is %c.\n\r", 'a' + c_choice - 1);
adc_clear_status(&g_adc_inst, ADCIFE_SCR_WM);
adc_enable_interrupt(&g_adc_inst, ADC_WINDOW_MONITOR);
break;
case 'm':
display_menu();
break;
case 'i':
display_info();
adc_clear_status(&g_adc_inst, ADCIFE_SCR_WM);
adc_enable_interrupt(&g_adc_inst, ADC_WINDOW_MONITOR);
break;
}
puts("Press \'m\' or \'M\' to display the main menu again!\r");
}
}
