/* Charging power state initialization */ int charger_post_init(void) { int rv; int option; rv = charger_get_option(&option); if (rv) return rv; /* Don't be noisy */ option |= OPT_AUDIO_FREQ_40KHZ_LIMIT; /* Always monitor adapter current (40X multiplier). */ option |= OPT_FIX_IOUT_ALWAYS; option &= ~OPT_IOUT_MASK; option &= ~OPT_LEARN_MASK; /* Enable dynamic power management */ option |= OPT_IDPM_ENABLE; rv = charger_set_option(option); if (rv) return rv; rv = charger_set_input_current(CONFIG_CHARGER_INPUT_CURRENT); return rv; }
/* Charging power state initialization */ int charger_post_init(void) { int rv; #ifdef CONFIG_CHARGER_ILIM_PIN_DISABLED int option2; #endif /* Set charger input current limit */ rv = charger_set_input_current(CONFIG_CHARGER_INPUT_CURRENT); #ifdef CONFIG_CHARGER_ILIM_PIN_DISABLED if (rv) return rv; /* Disable the external ILIM pin. */ rv = i2c_read16(I2C_PORT_CHARGER, BQ24773_ADDR, BQ24773_CHARGE_OPTION2, &option2); if (rv) return rv; option2 &= ~OPTION2_EN_EXTILIM; rv = i2c_write16(I2C_PORT_CHARGER, BQ24773_ADDR, BQ24773_CHARGE_OPTION2, option2); #endif return rv; }
/* * This can override the smart battery's charging profile. To make a change, * modify one or more of requested_voltage, requested_current, or state. * Leave everything else unchanged. * * Return the next poll period in usec, or zero to use the default (which is * state dependent). */ int charger_profile_override(struct charge_state_data *curr) { int rv; /* We only want to override how we charge, nothing else. */ if (curr->state != ST_CHARGE) return 0; /* Bump the input current up a little at a time if needed. */ if (curr->chg.input_current < MAX_INPUT_CURRENT) { rv = charger_set_input_current(curr->chg.input_current + INPUT_CURRENT_INCR); /* * If we can't set the input current, indicate the error * (negative, since positive changes the poll period) and * don't override the default behavior. */ if (rv) return -rv; } /* Do we want to mess with the charge profile too? */ if (!fast_charging_allowed) return 0; /* Okay, impose our custom will */ curr->requested_current = 9000; curr->requested_voltage = 8300; if (curr->batt.current <= 6300) { curr->requested_current = 6300; curr->requested_voltage = 8400; } else if (curr->batt.current <= 4500) { curr->requested_current = 4500; curr->requested_voltage = 8500; } else if (curr->batt.current <= 2700) { curr->requested_current = 2700; curr->requested_voltage = 8700; } else if (curr->batt.current <= 475) { /* * Should we stop? If so, how do we start again? * For now, just use the battery's profile. */ curr->requested_current = curr->batt.desired_current; curr->requested_voltage = curr->batt.desired_voltage; } return 0; }
int charge_set_input_current_limit(int ma) { /* * If battery is not present and we are not locked, then allow system * to pull as much input current as needed. Yes, we might overcurrent * the charger but this is no worse then browning out due to * insufficient input current. */ if (curr.batt.is_present != BP_YES && !system_is_locked()) return EC_SUCCESS; #ifdef CONFIG_CHARGER_MAX_INPUT_CURRENT /* Limit input current limit to max limit for this board */ ma = MIN(ma, CONFIG_CHARGER_MAX_INPUT_CURRENT); #endif curr.desired_input_current = ma; return charger_set_input_current(ma); }
/* Charging power state initialization */ int charger_post_init(void) { /* * Note: bq24735 power on reset state is: * watch dog timer = 175 sec * input current limit = ~1/2 maximum setting * charging voltage = 0 mV * charging current = 0 mA */ int rv, option; rv = charger_get_option(&option); if (rv) return rv; option &= ~OPTION_LEARN_ENABLE; rv = charger_set_option(option); if (rv) return rv; /* Set charger input current limit */ return charger_set_input_current(CONFIG_CHARGER_INPUT_CURRENT); }
/* Main loop */ void charger_task(void) { int sleep_usec; int need_static = 1; const struct charger_info * const info = charger_get_info(); /* Get the battery-specific values */ batt_info = battery_get_info(); prev_ac = prev_charge = -1; chg_ctl_mode = CHARGE_CONTROL_NORMAL; shutdown_warning_time.val = 0UL; battery_seems_to_be_dead = 0; /* * If system is not locked and we don't have a battery to live on, * then use max input current limit so that we can pull as much power * as needed. */ battery_get_params(&curr.batt); prev_bp = curr.batt.is_present; curr.desired_input_current = get_desired_input_current(prev_bp, info); while (1) { #ifdef CONFIG_SB_FIRMWARE_UPDATE if (sb_fw_update_in_progress()) { task_wait_event(CHARGE_MAX_SLEEP_USEC); continue; } #endif /* Let's see what's going on... */ curr.ts = get_time(); sleep_usec = 0; problems_exist = 0; curr.ac = extpower_is_present(); if (curr.ac != prev_ac) { if (curr.ac) { /* * Some chargers are unpowered when the AC is * off, so we'll reinitialize it when AC * comes back and set the input current limit. * Try again if it fails. */ int rv = charger_post_init(); if (rv != EC_SUCCESS) { problem(PR_POST_INIT, rv); } else { if (curr.desired_input_current != CHARGE_CURRENT_UNINITIALIZED) rv = charger_set_input_current( curr.desired_input_current); if (rv != EC_SUCCESS) problem(PR_SET_INPUT_CURR, rv); else prev_ac = curr.ac; } } else { /* Some things are only meaningful on AC */ chg_ctl_mode = CHARGE_CONTROL_NORMAL; battery_seems_to_be_dead = 0; prev_ac = curr.ac; } } charger_get_params(&curr.chg); battery_get_params(&curr.batt); if (prev_bp != curr.batt.is_present) { prev_bp = curr.batt.is_present; /* Update battery info due to change of battery */ batt_info = battery_get_info(); need_static = 1; curr.desired_input_current = get_desired_input_current(prev_bp, info); if (curr.desired_input_current != CHARGE_CURRENT_UNINITIALIZED) charger_set_input_current( curr.desired_input_current); hook_notify(HOOK_BATTERY_SOC_CHANGE); } /* * TODO(crosbug.com/p/27527). Sometimes the battery thinks its * temperature is 6280C, which seems a bit high. Let's ignore * anything above the boiling point of tungsten until this bug * is fixed. If the battery is really that warm, we probably * have more urgent problems. */ if (curr.batt.temperature > CELSIUS_TO_DECI_KELVIN(5660)) { CPRINTS("ignoring ridiculous batt.temp of %dC", DECI_KELVIN_TO_CELSIUS(curr.batt.temperature)); curr.batt.flags |= BATT_FLAG_BAD_TEMPERATURE; } /* If the battery thinks it's above 100%, don't believe it */ if (curr.batt.state_of_charge > 100) { CPRINTS("ignoring ridiculous batt.soc of %d%%", curr.batt.state_of_charge); curr.batt.flags |= BATT_FLAG_BAD_STATE_OF_CHARGE; } /* * Now decide what we want to do about it. We'll normally just * pass along whatever the battery wants to the charger. Note * that if battery_get_params() can't get valid values from the * battery it uses (0, 0), which is probably safer than blindly * applying power to a battery we can't talk to. */ curr.requested_voltage = curr.batt.desired_voltage; curr.requested_current = curr.batt.desired_current; /* If we *know* there's no battery, wait for one to appear. */ if (curr.batt.is_present == BP_NO) { ASSERT(curr.ac); /* How are we running? */ curr.state = ST_IDLE; curr.batt_is_charging = 0; battery_was_removed = 1; goto wait_for_it; } /* * If we had trouble talking to the battery or the charger, we * should probably do nothing for a bit, and if it doesn't get * better then flag it as an error. */ if (curr.chg.flags & CHG_FLAG_BAD_ANY) problem(PR_CHG_FLAGS, curr.chg.flags); if (curr.batt.flags & BATT_FLAG_BAD_ANY) problem(PR_BATT_FLAGS, curr.batt.flags); /* * If AC is present, check if input current is sufficient to * actually charge battery. */ curr.batt_is_charging = curr.ac && (curr.batt.current >= 0); /* Don't let the battery hurt itself. */ shutdown_on_critical_battery(); if (!curr.ac) { curr.state = ST_DISCHARGE; goto wait_for_it; } /* Okay, we're on AC and we should have a battery. */ /* Used for factory tests. */ if (chg_ctl_mode != CHARGE_CONTROL_NORMAL) { curr.state = ST_IDLE; goto wait_for_it; } /* If the battery is not responsive, try to wake it up. */ if (!(curr.batt.flags & BATT_FLAG_RESPONSIVE)) { if (battery_seems_to_be_dead || battery_is_cut_off()) { /* It's dead, do nothing */ curr.state = ST_IDLE; curr.requested_voltage = 0; curr.requested_current = 0; } else if (curr.state == ST_PRECHARGE && (get_time().val > precharge_start_time.val + PRECHARGE_TIMEOUT_US)) { /* We've tried long enough, give up */ CPRINTS("battery seems to be dead"); battery_seems_to_be_dead = 1; curr.state = ST_IDLE; curr.requested_voltage = 0; curr.requested_current = 0; } else { /* See if we can wake it up */ if (curr.state != ST_PRECHARGE) { CPRINTS("try to wake battery"); precharge_start_time = get_time(); need_static = 1; } curr.state = ST_PRECHARGE; curr.requested_voltage = batt_info->voltage_max; curr.requested_current = batt_info->precharge_current; } goto wait_for_it; } else { /* The battery is responding. Yay. Try to use it. */ #ifdef CONFIG_BATTERY_REQUESTS_NIL_WHEN_DEAD /* * TODO (crosbug.com/p/29467): remove this workaround * for dead battery that requests no voltage/current */ if (curr.requested_voltage == 0 && curr.requested_current == 0 && curr.batt.state_of_charge == 0) { /* Battery is dead, give precharge current */ curr.requested_voltage = batt_info->voltage_max; curr.requested_current = batt_info->precharge_current; } else #endif #ifdef CONFIG_BATTERY_REVIVE_DISCONNECT battery_seems_to_be_disconnected = 0; if (curr.requested_voltage == 0 && curr.requested_current == 0 && battery_get_disconnect_state() == BATTERY_DISCONNECTED) { /* * Battery is in disconnect state. Apply a * current to kick it out of this state. */ CPRINTS("found battery in disconnect state"); curr.requested_voltage = batt_info->voltage_max; curr.requested_current = batt_info->precharge_current; battery_seems_to_be_disconnected = 1; } else #endif if (curr.state == ST_PRECHARGE || battery_seems_to_be_dead || battery_was_removed) { CPRINTS("battery woke up"); /* Update the battery-specific values */ batt_info = battery_get_info(); need_static = 1; } battery_seems_to_be_dead = battery_was_removed = 0; curr.state = ST_CHARGE; } /* * TODO(crosbug.com/p/27643): Quit trying if charging too long * without getting full (CONFIG_CHARGER_TIMEOUT_HOURS). */ wait_for_it: #ifdef CONFIG_CHARGER_PROFILE_OVERRIDE sleep_usec = charger_profile_override(&curr); if (sleep_usec < 0) problem(PR_CUSTOM, sleep_usec); #endif /* Keep the AP informed */ if (need_static) need_static = update_static_battery_info(); /* Wait on the dynamic info until the static info is good. */ if (!need_static) update_dynamic_battery_info(); notify_host_of_low_battery(); /* And the EC console */ is_full = calc_is_full(); if ((!(curr.batt.flags & BATT_FLAG_BAD_STATE_OF_CHARGE) && curr.batt.state_of_charge != prev_charge) || (is_full != prev_full)) { show_charging_progress(); prev_charge = curr.batt.state_of_charge; hook_notify(HOOK_BATTERY_SOC_CHANGE); } prev_full = is_full; /* Turn charger off if it's not needed */ if (curr.state == ST_IDLE || curr.state == ST_DISCHARGE) { curr.requested_voltage = 0; curr.requested_current = 0; } /* Apply external limits */ if (curr.requested_current > user_current_limit) curr.requested_current = user_current_limit; /* Round to valid values */ curr.requested_voltage = charger_closest_voltage(curr.requested_voltage); curr.requested_current = charger_closest_current(curr.requested_current); /* Charger only accpets request when AC is on. */ if (curr.ac) { /* * Some batteries would wake up after cut-off if we keep * charging it. Thus, we only charge when AC is on and * battery is not cut off yet. */ if (battery_is_cut_off()) charge_request(0, 0); /* * As a safety feature, some chargers will stop * charging if we don't communicate with it frequently * enough. In manual mode, we'll just tell it what it * knows. */ else if (manual_mode) { charge_request(curr.chg.voltage, curr.chg.current); } else { charge_request(curr.requested_voltage, curr.requested_current); } } else { charge_request( charger_closest_voltage( curr.batt.voltage + info->voltage_step), -1); } /* How long to sleep? */ if (problems_exist) /* If there are errors, don't wait very long. */ sleep_usec = CHARGE_POLL_PERIOD_SHORT; else if (sleep_usec <= 0) { /* default values depend on the state */ if (curr.state == ST_IDLE || curr.state == ST_DISCHARGE) { /* If AP is off, we can sleep a long time */ if (chipset_in_state(CHIPSET_STATE_ANY_OFF | CHIPSET_STATE_SUSPEND)) sleep_usec = CHARGE_POLL_PERIOD_VERY_LONG; else /* Discharging, not too urgent */ sleep_usec = CHARGE_POLL_PERIOD_LONG; } else { /* Charging, so pay closer attention */ sleep_usec = CHARGE_POLL_PERIOD_CHARGE; } } /* Adjust for time spent in this loop */ sleep_usec -= (int)(get_time().val - curr.ts.val); if (sleep_usec < CHARGE_MIN_SLEEP_USEC) sleep_usec = CHARGE_MIN_SLEEP_USEC; else if (sleep_usec > CHARGE_MAX_SLEEP_USEC) sleep_usec = CHARGE_MAX_SLEEP_USEC; task_wait_event(sleep_usec); } }
static int charge_command_charge_state(struct host_cmd_handler_args *args) { const struct ec_params_charge_state *in = args->params; struct ec_response_charge_state *out = args->response; uint32_t val; int rv = EC_RES_SUCCESS; switch (in->cmd) { case CHARGE_STATE_CMD_GET_STATE: out->get_state.ac = curr.ac; out->get_state.chg_voltage = curr.chg.voltage; out->get_state.chg_current = curr.chg.current; out->get_state.chg_input_current = curr.chg.input_current; out->get_state.batt_state_of_charge = curr.batt.state_of_charge; args->response_size = sizeof(out->get_state); break; case CHARGE_STATE_CMD_GET_PARAM: val = 0; #ifdef CONFIG_CHARGER_PROFILE_OVERRIDE /* custom profile params */ if (in->get_param.param >= CS_PARAM_CUSTOM_PROFILE_MIN && in->get_param.param <= CS_PARAM_CUSTOM_PROFILE_MAX) { rv = charger_profile_override_get_param( in->get_param.param, &val); } else #endif /* standard params */ switch (in->get_param.param) { case CS_PARAM_CHG_VOLTAGE: val = curr.chg.voltage; break; case CS_PARAM_CHG_CURRENT: val = curr.chg.current; break; case CS_PARAM_CHG_INPUT_CURRENT: val = curr.chg.input_current; break; case CS_PARAM_CHG_STATUS: val = curr.chg.status; break; case CS_PARAM_CHG_OPTION: val = curr.chg.option; break; case CS_PARAM_LIMIT_POWER: #ifdef CONFIG_CHARGER_LIMIT_POWER_THRESH_BAT_PCT /* * LIMIT_POWER status is based on battery level * and external charger power. */ if ((curr.batt.is_present != BP_YES || curr.batt.state_of_charge < CONFIG_CHARGER_LIMIT_POWER_THRESH_BAT_PCT) && charge_manager_get_power_limit_uw() < CONFIG_CHARGER_LIMIT_POWER_THRESH_CHG_MW * 1000 && system_is_locked()) val = 1; else #endif val = 0; break; default: rv = EC_RES_INVALID_PARAM; } /* got something */ out->get_param.value = val; args->response_size = sizeof(out->get_param); break; case CHARGE_STATE_CMD_SET_PARAM: val = in->set_param.value; #ifdef CONFIG_CHARGER_PROFILE_OVERRIDE /* custom profile params */ if (in->set_param.param >= CS_PARAM_CUSTOM_PROFILE_MIN && in->set_param.param <= CS_PARAM_CUSTOM_PROFILE_MAX) { rv = charger_profile_override_set_param( in->set_param.param, val); } else #endif switch (in->set_param.param) { case CS_PARAM_CHG_VOLTAGE: val = charger_closest_voltage(val); if (charge_request(val, -1)) rv = EC_RES_ERROR; manual_mode = 1; break; case CS_PARAM_CHG_CURRENT: val = charger_closest_current(val); if (charge_request(-1, val)) rv = EC_RES_ERROR; manual_mode = 1; break; case CS_PARAM_CHG_INPUT_CURRENT: if (charger_set_input_current(val)) rv = EC_RES_ERROR; break; case CS_PARAM_CHG_STATUS: case CS_PARAM_LIMIT_POWER: /* Can't set this */ rv = EC_RES_ACCESS_DENIED; break; case CS_PARAM_CHG_OPTION: if (charger_set_option(val)) rv = EC_RES_ERROR; break; default: rv = EC_RES_INVALID_PARAM; } break; default: CPRINTS("EC_CMD_CHARGE_STATE: bad cmd 0x%x", in->cmd); rv = EC_RES_INVALID_PARAM; } return rv; }