C++ (Cpp) configure_emmc Examples

Example #1

File: mainboard.c Project: punitvara/coreboot

static void mainboard_init(device_t dev)
{
	gpio_output(GPIO_RESET, 0);

	configure_usb();
	configure_emmc();
	configure_codec();
	configure_vop();
}

Example #2

File: mainboard.c Project: zamaudio/coreboot

static void mainboard_init(device_t dev)
{
	gpio_output(GPIO_RESET, 0);

	configure_usb();
	configure_emmc();
	configure_codec();
	/* No video. */

	elog_init();
	elog_add_watchdog_reset();
	elog_add_boot_reason();
}

Example #3

File: mainboard.c Project: tidatida/coreboot

static void mainboard_init(device_t dev)
{
	setbits_le32(&rk3288_pmu->iomux_i2c0scl, IOMUX_I2C0SCL); /* PMIC I2C */
	setbits_le32(&rk3288_pmu->iomux_i2c0sda, IOMUX_I2C0SDA); /* PMIC I2C */
	i2c_init(0, 400000);	/* PMIC I2C */

	gpio_output(GPIO_RESET, 0);

	configure_usb();
	configure_sdmmc();
	configure_emmc();
	configure_codec();
	configure_vop();
}

Example #4

File: rk3288-board-spl.c Project: analogdevicesinc/u-boot-xlnx

void spl_board_init(void)
{
	struct udevice *pinctrl;
	int ret;

	ret = setup_led();

	if (ret) {
		debug("LED ret=%d\n", ret);
		hang();
	}

	ret = uclass_get_device(UCLASS_PINCTRL, 0, &pinctrl);
	if (ret) {
		debug("%s: Cannot find pinctrl device\n", __func__);
		goto err;
	}

#ifdef CONFIG_SPL_MMC_SUPPORT
	ret = pinctrl_request_noflags(pinctrl, PERIPH_ID_SDCARD);
	if (ret) {
		debug("%s: Failed to set up SD card\n", __func__);
		goto err;
	}
	ret = configure_emmc(pinctrl);
	if (ret) {
		debug("%s: Failed to set up eMMC\n", __func__);
		goto err;
	}
#endif

	/* Enable debug UART */
	ret = pinctrl_request_noflags(pinctrl, PERIPH_ID_UART_DBG);
	if (ret) {
		debug("%s: Failed to set up console UART\n", __func__);
		goto err;
	}

	preloader_console_init();
#if CONFIG_IS_ENABLED(ROCKCHIP_BACK_TO_BROM)
	back_to_bootrom(BROM_BOOT_NEXTSTAGE);
#endif
	return;
err:
	printf("spl_board_init: Error %d\n", ret);

	/* No way to report error here */
	hang();
}

Example #5

File: mainboard.c Project: lynxis/coreboot-signed

static void mainboard_init(device_t dev)
{
	gpio_output(GPIO_RESET, 0);

	configure_usb();
	configure_emmc();
	configure_codec();
	configure_3g();
	/* No video. */

	/* If recovery mode is detected, reduce frequency and voltage to reduce
	 * heat in case machine is left unattended. chrome-os-partner:41201. */
	if (vboot_recovery_mode_enabled())  {
		printk(BIOS_DEBUG, "Reducing APLL freq for recovery mode.\n");
		rkclk_configure_cpu(APLL_600_MHZ);
		rk808_configure_buck(1, 900);
	}
}