void ANO_Hexacopter_board_Init(void)
{
//中断优先级组别设置
NVIC_PriorityGroupConfig(NVIC_PriorityGroup_4);
//初始化系统滴答定时器
cycleCounterInit();
SysTick_Config(SystemCoreClock / 1000);
//初始化模拟I2C
ANO_I2C_Soft::Init();
//初始化SPI2
ANO_SPI2::Init();
//初始化NRF
nrf.Init(MODEL_TX2,89);
//初始化定时器输出PWM,24KHz
ANO_PWM::out_Init(24000);
uart3.Init(9600);
ANO_LED::Init();
//解锁flash
FLASH_Unlock();
//初始化虚拟eeprom设置
EE_Init();
}
void systemInit(void)
{
#ifdef CC3D
/* Accounts for OP Bootloader, set the Vector Table base address as specified in .ld file */
extern void *isr_vector_table_base;
NVIC_SetVectorTable((uint32_t)&isr_vector_table_base, 0x0);
#endif
// Configure NVIC preempt/priority groups
NVIC_PriorityGroupConfig(NVIC_PRIORITY_GROUPING);
#ifdef STM32F10X
// Turn on clocks for stuff we use
RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO, ENABLE);
#endif
RCC_ClearFlag();
enableGPIOPowerUsageAndNoiseReductions();
#ifdef STM32F10X
// Turn off JTAG port 'cause we're using the GPIO for leds
#define AFIO_MAPR_SWJ_CFG_NO_JTAG_SW (0x2 << 24)
AFIO->MAPR |= AFIO_MAPR_SWJ_CFG_NO_JTAG_SW;
#endif
// Init cycle counter
cycleCounterInit();
// SysTick
SysTick_Config(SystemCoreClock / 1000);
}
void systemInit(void)
{
// Configure NVIC preempt/priority groups
NVIC_PriorityGroupConfig(NVIC_PRIORITY_GROUPING);
#ifdef STM32F10X
// Turn on clocks for stuff we use
RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO, ENABLE);
#endif
// cache RCC->CSR value to use it in isMPUSoftreset() and others
cachedRccCsrValue = RCC->CSR;
RCC_ClearFlag();
enableGPIOPowerUsageAndNoiseReductions();
#ifdef STM32F10X
// Turn off JTAG port 'cause we're using the GPIO for leds
#define AFIO_MAPR_SWJ_CFG_NO_JTAG_SW (0x2 << 24)
AFIO->MAPR |= AFIO_MAPR_SWJ_CFG_NO_JTAG_SW;
#endif
// Init cycle counter
cycleCounterInit();
memset(&exti15_10_handlers, 0x00, sizeof(exti15_10_handlers));
// SysTick
SysTick_Config(SystemCoreClock / 1000);
}
void systemInit(void)
{
checkForBootLoaderRequest();
SetSysClock();
// Configure NVIC preempt/priority groups
NVIC_PriorityGroupConfig(NVIC_PRIORITY_GROUPING);
// cache RCC->CSR value to use it in isMPUSoftreset() and others
cachedRccCsrValue = RCC->CSR;
/* Accounts for OP Bootloader, set the Vector Table base address as specified in .ld file */
extern void *isr_vector_table_base;
NVIC_SetVectorTable((uint32_t)&isr_vector_table_base, 0x0);
RCC_AHB2PeriphClockCmd(RCC_AHB2Periph_OTG_FS, DISABLE);
RCC_ClearFlag();
enableGPIOPowerUsageAndNoiseReductions();
// Init cycle counter
cycleCounterInit();
memset(extiHandlerConfigs, 0x00, sizeof(extiHandlerConfigs));
// SysTick
SysTick_Config(SystemCoreClock / 1000);
}
void systemInit(void)
{
checkForBootLoaderRequest();
//SystemClock_Config();
// Configure NVIC preempt/priority groups
HAL_NVIC_SetPriorityGrouping(NVIC_PRIORITY_GROUPING);
// cache RCC->CSR value to use it in isMPUSoftReset() and others
cachedRccCsrValue = RCC->CSR;
/* Accounts for OP Bootloader, set the Vector Table base address as specified in .ld file */
//extern void *isr_vector_table_base;
//NVIC_SetVectorTable((uint32_t)&isr_vector_table_base, 0x0);
//__HAL_RCC_USB_OTG_FS_CLK_DISABLE;
//RCC_ClearFlag();
enableGPIOPowerUsageAndNoiseReductions();
// Init cycle counter
cycleCounterInit();
// SysTick
//SysTick_Config(SystemCoreClock / 1000);
HAL_SYSTICK_Config(HAL_RCC_GetHCLKFreq()/1000);
HAL_SYSTICK_CLKSourceConfig(SYSTICK_CLKSOURCE_HCLK);
}
void systemInit(bool overclock)
{
#ifdef STM32F303xC
// start fpu
SCB->CPACR = (0x3 << (10*2)) | (0x3 << (11*2));
#endif
#ifdef STM32F303xC
SetSysClock();
#endif
#ifdef STM32F10X_MD
// Configure the System clock frequency, HCLK, PCLK2 and PCLK1 prescalers
// Configure the Flash Latency cycles and enable prefetch buffer
SetSysClock(overclock);
#endif
// Configure NVIC preempt/priority groups
NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2);
#ifdef STM32F10X_MD
// Turn on clocks for stuff we use
RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO, ENABLE);
#endif
RCC_ClearFlag();
enableGPIOPowerUsageAndNoiseReductions();
#ifdef STM32F10X_MD
// Turn off JTAG port 'cause we're using the GPIO for leds
#define AFIO_MAPR_SWJ_CFG_NO_JTAG_SW (0x2 << 24)
AFIO->MAPR |= AFIO_MAPR_SWJ_CFG_NO_JTAG_SW;
#endif
ledInit();
beeperInit();
// Init cycle counter
cycleCounterInit();
// SysTick
SysTick_Config(SystemCoreClock / 1000);
#ifdef CC3D
spiInit(SPI1);
spiInit(SPI2);
#endif
#ifndef CC3D
// Configure the rest of the stuff
i2cInit(I2C2);
#endif
// sleep for 100ms
delay(100);
}
static void systemTimekeepingSetup(void)
{
RCC_ClocksTypeDef clocks;
RCC_GetClocksFreq(&clocks);
cycleCounterInit();
SysTick_Config(clocks.SYSCLK_Frequency / 1000);
}
void systemInit(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
uint8_t i;
gpio_config_t gpio_cfg[] = {
{ LED0_GPIO, LED0_PIN, GPIO_Mode_Out_PP }, // PB3 (LED)
{ LED1_GPIO, LED1_PIN, GPIO_Mode_Out_PP }, // PB4 (LED)
#ifndef FY90Q
{ BEEP_GPIO, BEEP_PIN, GPIO_Mode_Out_OD }, // PA12 (Buzzer)
#endif
};
uint8_t gpio_count = sizeof(gpio_cfg) / sizeof(gpio_cfg[0]);
// Turn on clocks for stuff we use
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM2 | RCC_APB1Periph_TIM3 | RCC_APB1Periph_TIM4 | RCC_APB1Periph_I2C2, ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO | RCC_APB2Periph_GPIOA | RCC_APB2Periph_GPIOB | RCC_APB2Periph_GPIOC | RCC_APB2Periph_TIM1 | RCC_APB2Periph_ADC1 | RCC_APB2Periph_USART1, ENABLE);
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA1, ENABLE);
RCC_ClearFlag();
// Make all GPIO in by default to save power and reduce noise
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_All;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AIN;
GPIO_Init(GPIOA, &GPIO_InitStructure);
GPIO_Init(GPIOB, &GPIO_InitStructure);
GPIO_Init(GPIOC, &GPIO_InitStructure);
// Turn off JTAG port 'cause we're using the GPIO for leds
GPIO_PinRemapConfig(GPIO_Remap_SWJ_JTAGDisable, ENABLE);
// Configure gpio
for (i = 0; i < gpio_count; i++) {
GPIO_InitStructure.GPIO_Pin = gpio_cfg[i].pin;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = gpio_cfg[i].mode;
GPIO_Init(gpio_cfg[i].gpio, &GPIO_InitStructure);
}
LED0_OFF;
LED1_OFF;
BEEP_OFF;
// Init cycle counter
cycleCounterInit();
// SysTick
SysTick_Config(SystemCoreClock / 1000);
// Configure the rest of the stuff
adcInit();
#ifndef FY90Q
i2cInit(I2C2);
#endif
// sleep for 100ms
delay(100);
}
void systemInit(void)
{
#ifdef CC3D
/* Accounts for OP Bootloader, set the Vector Table base address as specified in .ld file */
extern void *isr_vector_table_base;
NVIC_SetVectorTable((uint32_t)&isr_vector_table_base, 0x0);
#endif
// Configure NVIC preempt/priority groups
NVIC_PriorityGroupConfig(NVIC_PRIORITY_GROUPING);
#ifdef STM32F10X
// Turn on clocks for stuff we use
RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO, ENABLE);
#endif
// cache RCC->CSR value to use it in isMPUSoftreset() and others
cachedRccCsrValue = RCC->CSR;
#ifdef STM32F40_41xxx
/* Accounts for OP Bootloader, set the Vector Table base address as specified in .ld file */
extern void *isr_vector_table_base;
NVIC_SetVectorTable((uint32_t)&isr_vector_table_base, 0x0);
RCC_AHB2PeriphClockCmd( RCC_AHB2Periph_OTG_FS, DISABLE);
#endif
RCC_ClearFlag();
enableGPIOPowerUsageAndNoiseReductions();
#ifdef STM32F10X
// Set USART1 TX (PA9) to output and high state to prevent a rs232 break condition on reset.
// See issue https://github.com/cleanflight/cleanflight/issues/1433
gpio_config_t gpio;
gpio.mode = Mode_Out_PP;
gpio.speed = Speed_2MHz;
gpio.pin = Pin_9;
digitalHi(GPIOA, gpio.pin);
gpioInit(GPIOA, &gpio);
// Turn off JTAG port 'cause we're using the GPIO for leds
#define AFIO_MAPR_SWJ_CFG_NO_JTAG_SW (0x2 << 24)
AFIO->MAPR |= AFIO_MAPR_SWJ_CFG_NO_JTAG_SW;
#endif
// Init cycle counter
cycleCounterInit();
memset(extiHandlerConfigs, 0x00, sizeof(extiHandlerConfigs));
// SysTick
SysTick_Config(SystemCoreClock / 1000);
}
void systemInit(void)
{
// Init cycle counter
cycleCounterInit();
// SysTick
SysTick_Config(SystemCoreClock / 1000);
///////////////////////////////////
checkFirstTime(false);
readEEPROM();
if (eepromConfig.receiverType == SPEKTRUM)
checkSpektrumBind();
checkResetType();
NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2); // 2 bits for pre-emption priority, 2 bits for subpriority
initMixer();
ledInit();
cliInit();
BLUE_LED_ON;
delay(20000); // 20 sec total delay for sensor stabilization - probably not long enough.....
adcInit();
batteryInit();
gpsInit();
i2cInit(I2C1);
i2cInit(I2C2);
pwmEscInit(eepromConfig.escPwmRate);
pwmServoInit(eepromConfig.servoPwmRate);
rxInit();
spiInit(SPI2);
spiInit(SPI3);
telemetryInit();
timingFunctionsInit();
initFirstOrderFilter();
initGPS();
initMax7456();
initPID();
GREEN_LED_ON;
initMPU6000();
initMag(HMC5883L_I2C);
initPressure(MS5611_I2C);
}
void systemInit(void) {
GPIO_InitTypeDef GPIO_InitStructure;
gpio_config_t gpio_cfg[] = {
{ LEDR_GPIO, LEDR_PIN, GPIO_Mode_Out_PP },
{ LEDG_GPIO, LEDG_PIN, GPIO_Mode_Out_PP },
};
uint8_t gpio_count = sizeof(gpio_cfg) / sizeof(gpio_cfg[0]);
uint32_t i;
// This is needed because some shit inside Keil startup f***s with SystemCoreClock, setting it back to 72MHz even on HSI.
SystemCoreClockUpdate();
// Turn on clocks for stuff we use
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM2 | RCC_APB1Periph_TIM3 | RCC_APB1Periph_TIM4 | RCC_APB1Periph_I2C2 | RCC_APB1Periph_SPI2, ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO | RCC_APB2Periph_GPIOA | RCC_APB2Periph_GPIOB | RCC_APB2Periph_GPIOC | RCC_APB2Periph_TIM1 | RCC_APB2Periph_ADC1 | RCC_APB2Periph_USART1, ENABLE);
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA1, ENABLE);
RCC_ClearFlag();
// Make all GPIO in by default to save power and reduce noise
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_All;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AIN;
GPIO_Init(GPIOA, &GPIO_InitStructure);
GPIO_Init(GPIOB, &GPIO_InitStructure);
GPIO_Init(GPIOC, &GPIO_InitStructure);
// Turn off JTAG port 'cause we're using the GPIO for leds
GPIO_PinRemapConfig(GPIO_Remap_SWJ_Disable, ENABLE);
// Configure gpio
for (i = 0; i < gpio_count; i++) {
GPIO_InitStructure.GPIO_Pin = gpio_cfg[i].pin;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_2MHz;
GPIO_InitStructure.GPIO_Mode = gpio_cfg[i].mode;
GPIO_Init(gpio_cfg[i].gpio, &GPIO_InitStructure);
}
LEDR_OFF
LEDG_OFF
// Init cycle counter
cycleCounterInit();
// SysTick
SysTick_Config(SystemCoreClock / 1000);
// Configure the rest of the stuff
i2cInit(I2C2);
// sleep for 100ms
delay(100);
}
void systemInit(void)
{
checkForBootLoaderRequest();
// Enable FPU
SCB->CPACR = (0x3 << (10 * 2)) | (0x3 << (11 * 2));
SetSysClock();
// Configure NVIC preempt/priority groups
NVIC_PriorityGroupConfig(NVIC_PRIORITY_GROUPING);
// cache RCC->CSR value to use it in isMPUSoftreset() and others
cachedRccCsrValue = RCC->CSR;
RCC_ClearFlag();
enableGPIOPowerUsageAndNoiseReductions();
// Init cycle counter
cycleCounterInit();
memset(extiHandlerConfigs, 0x00, sizeof(extiHandlerConfigs));
// SysTick
SysTick_Config(SystemCoreClock / 1000);
}
void systemInit(bool overclock)
{
//RCC_ClocksTypeDef rccClocks;
int i;
// start fpu
SCB->CPACR = (0x3 << (10*2)) | (0x3 << (11*2));
// Init cycle counter
cycleCounterInit();
// SysTick
SysTick_Config(SystemCoreClock / 1000);
RCC_ADCCLKConfig(RCC_ADC12PLLCLK_Div256); // 72 MHz divided by 256 = 281.25 kHz
// Turn on peripherial clocks
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_ADC12, ENABLE);
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA1, ENABLE); // USART1, USART2
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA2, ENABLE); // ADC2
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOA, ENABLE);
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOB, ENABLE);
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOC, ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_SPI2, ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM2, ENABLE); // PWM Out + PWM RX
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM3, ENABLE); // PWM Out
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM4, ENABLE); // PWM Out + PWM RX
// RCC_APB1PeriphClockCmd(RCC_APB1Periph_I2C2, ENABLE); // i2c
// RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM7, ENABLE); //
//
RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM1, ENABLE); // PPM + PWM RX
// RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM8, ENABLE); //
RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM15, ENABLE); // PWM Out
RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM16, ENABLE); // PWM Out
RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM17, ENABLE); // PWM Out
RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1, ENABLE); // Telemetry
RCC_APB1PeriphClockCmd(RCC_APB1Periph_USART2, ENABLE); // GPS
RCC_APB1PeriphClockCmd(RCC_APB1Periph_USART3, ENABLE); // Spektrum RX
RCC_ClearFlag();
NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2); // 2 bits for pre-emption priority, 2 bits for subpriority
gpioStart();
spiInit();
for (i = 0; i < 10; i++) {
LED0_TOGGLE
delay(25);
BEEP_ON
delay(25);
BEEP_OFF
}
LED0_OFF
}
void systemInit(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
uint8_t i;
gpio_config_t gpio_cfg[] = {
{LED0_GPIO, LED0_PIN, GPIO_Mode_Out_PP}, // PB3 (LED)
{LED1_GPIO, LED1_PIN, GPIO_Mode_Out_PP}, // PB4 (LED)
};
uint8_t gpio_count = sizeof(gpio_cfg) / sizeof(gpio_cfg[0]);
// Turn on clocks for stuff we use
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA | RCC_APB2Periph_GPIOB | RCC_APB2Periph_GPIOC | RCC_APB2Periph_AFIO, ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM1, ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM2, ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM3, ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM4, ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1, ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1, ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_I2C2, ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_I2C1, ENABLE);
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA1, ENABLE);
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA2, ENABLE);
RCC_ClearFlag();
// Make all GPIO in by default to save power and reduce noise
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_All;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AIN;
GPIO_Init(GPIOA, &GPIO_InitStructure);
GPIO_Init(GPIOB, &GPIO_InitStructure);
GPIO_Init(GPIOC, &GPIO_InitStructure);
// Turn off JTAG port 'cause we're using the GPIO for leds
GPIO_PinRemapConfig(GPIO_Remap_SWJ_JTAGDisable, ENABLE);
// Configure gpio
for (i = 0; i < gpio_count; i++) {
GPIO_InitStructure.GPIO_Pin = gpio_cfg[i].pin;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = gpio_cfg[i].mode;
GPIO_Init(gpio_cfg[i].gpio, &GPIO_InitStructure);
}
// Init cycle counter
cycleCounterInit();
// SysTick
SysTick_Config(SystemCoreClock / 1000);
LED0_OFF;
LED1_OFF;
NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2); // 2 bits for pre-emption priority, 2 bits for subpriority
checkFirstTime(false, false);
readEEPROM();
initMixer();
pwmOutputConfig.escPwmRate = systemConfig.escPwmRate;
pwmOutputConfig.servoPwmRate = systemConfig.servoPwmRate;
//i2cInit(SENSOR_I2C);
pwmInputInit();
pwmOutputInit(&pwmOutputConfig);
uartInit(115200);
//delay(10000); // 10 sec delay for sensor stabilization - probably not long enough.....
//initAccel();
//initGyro();
//initMag();
adcInit();
//initPressure(); // no pressure sensor
initPID();
}
void testInit(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
uint8_t i;
struct __gpio_config_t {
GPIO_TypeDef *gpio;
uint16_t pin;
GPIOMode_TypeDef mode;
}
gpio_cfg[] = {
{LED0_GPIO, LED0_PIN, GPIO_Mode_Out_PP}, // PB3 (LED)
{LED1_GPIO, LED1_PIN, GPIO_Mode_Out_PP}, // PB4 (LED)
};
uint8_t gpio_count = sizeof(gpio_cfg) / sizeof(gpio_cfg[0]);
// Turn on clocks for stuff we use
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA | RCC_APB2Periph_GPIOB | RCC_APB2Periph_GPIOC | RCC_APB2Periph_AFIO, ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM1, ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM2, ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM3, ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM4, ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1, ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1, ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_I2C2, ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_I2C1, ENABLE);
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA1, ENABLE);
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA2, ENABLE);
RCC_ClearFlag();
// Make all GPIO in by default to save power and reduce noise
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_All;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AIN;
GPIO_Init(GPIOA, &GPIO_InitStructure);
GPIO_Init(GPIOB, &GPIO_InitStructure);
GPIO_Init(GPIOC, &GPIO_InitStructure);
// Turn off JTAG port 'cause we're using the GPIO for leds
GPIO_PinRemapConfig(GPIO_Remap_SWJ_JTAGDisable, ENABLE);
// Configure gpio
for (i = 0; i < gpio_count; i++) {
GPIO_InitStructure.GPIO_Pin = gpio_cfg[i].pin;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = gpio_cfg[i].mode;
GPIO_Init(gpio_cfg[i].gpio, &GPIO_InitStructure);
}
// Init cycle counter
cycleCounterInit();
// SysTick
SysTick_Config(SystemCoreClock / 1000);
LED0_OFF;
LED1_OFF;
NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2); // 2 bits for pre-emption priority, 2 bits for subpriority
checkFirstTime(true,true);
initMixer();
pwmOutputConfig.motorPwmRate = 10*1000;
pwmOutputConfig.noEsc = true;
pwmOutputInit(&pwmOutputConfig);
i2cInit(SENSOR_I2C);
initGyro();
initAccel();
initMag();
nrf_init();
nrf_detect();
}
void systemInit(void)
{
RCC_ClocksTypeDef rccClocks;
///////////////////////////////////
// Init cycle counter
cycleCounterInit();
// SysTick
SysTick_Config(SystemCoreClock / 1000);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA | RCC_APB2Periph_GPIOB |
RCC_APB2Periph_GPIOC | RCC_APB2Periph_AFIO |
RCC_APB2Periph_TIM1 | RCC_APB2Periph_TIM8 |
RCC_APB2Periph_ADC1, ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM3 | RCC_APB1Periph_TIM4 |
RCC_APB1Periph_TIM5 | RCC_APB1Periph_TIM6 |
RCC_APB1Periph_I2C2, ENABLE);
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA1, ENABLE);
#ifdef _DTIMING
timingSetup();
#endif
///////////////////////////////////////////////////////////////////////////
checkFirstTime(false);
readEEPROM();
NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2); // 2 bits for pre-emption priority, 2 bits for subpriority
pwmMotorDriverInit();
cliInit();
gpioInit();
adcInit();
LED2_ON;
delay(10000); // 10 seconds of 20 second delay for sensor stabilization
if (GetVCPConnectMode() != eVCPConnectReset)
{
cliPrintF("\r\nUSB startup delay...\r\n");
delay(3000);
if (GetVCPConnectMode() == eVCPConnectData)
{
cliPrintF("\r\nBGC32 firmware starting up, USB connected...\r\n");
}
}
else
{
cliPrintF("\r\nDelaying for usb/serial driver to settle\r\n");
delay(3000);
cliPrintF("\r\nBGC32 firmware starting up, serial active...\r\n");
}
#ifdef __VERSION__
cliPrintF("\ngcc version " __VERSION__ "\n");
#endif
cliPrintF("BGC32 Firmware V%s, Build Date " __DATE__ " "__TIME__" \n", __BGC32_VERSION);
if ((RCC->CR & RCC_CR_HSERDY) != RESET)
{
cliPrintF("\nRunning on external HSE clock....\n");
}
else
{
cliPrintF("\nERROR: Running on internal HSI clock....\n");
}
RCC_GetClocksFreq(&rccClocks);
cliPrintF("\nADCCLK-> %2d MHz\n", rccClocks.ADCCLK_Frequency / 1000000);
cliPrintF( "HCLK-> %2d MHz\n", rccClocks.HCLK_Frequency / 1000000);
cliPrintF( "PCLK1-> %2d MHz\n", rccClocks.PCLK1_Frequency / 1000000);
cliPrintF( "PCLK2-> %2d MHz\n", rccClocks.PCLK2_Frequency / 1000000);
cliPrintF( "SYSCLK-> %2d MHz\n\n", rccClocks.SYSCLK_Frequency / 1000000);
delay(10000); // Remaining 10 seconds of 20 second delay for sensor stabilization - probably not long enough..
LED1_ON;
i2cInit(I2C2);
rcInit();
timingFunctionsInit();
BKPInit();
initFirstOrderFilter();
initPID();
initSinArray();
orientIMU();
initMPU6050();
// initMag();
}
int main(void)
{
static char ledsta;
/***********************************/
SystemClock_HSI(9); //系统时钟初始化，时钟源内部HSI
cycleCounterInit(); // Init cycle counter
SysTick_Config(SystemCoreClock / 1000); //SysTick开启系统tick定时器并初始化其中断，1ms
UART1_init(SysClock,uart1baudSet); //串口1初始化
NVIC_INIT(); //中断初始化
STMFLASH_Unlock(); //内部flash解锁
LoadParamsFromEEPROM(); //加载系统参数配置表
LedInit(); //IO初始化
Adc_Init(); //摇杆AD初始化
KeyInit(); //按键初始化
NRF24L01_INIT(); //NRF24L01初始化
SetTX_Mode(); //设无线模块为接收模式
controlClibra(); //遥控摇杆校准
#ifdef UART_DEBUG
TIM3_Init(SysClock,2000); //定时器初始化，1s为周期打印摇杆值
#endif
TIM4_Init(SysClock,TIME4_Preiod); //定时器4初始化，定时时间单位：(TIME4_Preiod)微秒
LedSet(led2,1);
LedSet(led3,1);
LoadRCdata(); //摇杆赋值
//RockerUnlockcrazepony(); //摆杆启动
Lockflag = 0; //解锁标志，1表示产生了一次按键操作，0表示该按键操作已经发送到飞控
LedSet(led2,0);
LedSet(led3,0);
while (1)
{
//10Hz loop
if(flag10Hz == 1) //10Hz
{
flag10Hz = 0;
/*status led*/
ledsta = !ledsta;
LedSet(signalLED,ledsta);
/*crazepony Lock*/
KeyLockcrazepony();
/*IMUcalibrate */
IMUcalibrate();
/*remote calibrate*/
Remotecalibrate();
}
//50Hz loop
if(flag50Hz == 1)
{
LoadRCdata();
flag50Hz = 0;
}
// 80Hz 12.5ms
if(flag80Hz)
{
flag80Hz = 0;
CommUAVUpload(MSP_SET_4CON);
}
}
}
void systemInit(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
//uint32_t i;
//GPIO_InitTypeDef GPIO_InitStructure;
/*RCC_AHB1PeriphClockCmd( RCC_AHB1Periph_GPIOE, ENABLE);
GPIO_InitStructure.GPIO_Pin = LED0_PIN | LED1_PIN | LED2_PIN| LED3_PIN;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_OUT;
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;
GPIO_Init(GPIOE, &GPIO_InitStructure);*/
/* Configure the GPIO_LED pins */
RCC_AHB1PeriphClockCmd( RCC_AHB1Periph_GPIOD, ENABLE);
GPIO_InitStructure.GPIO_Pin = LED0_PIN | LED1_PIN | LED2_PIN| LED3_PIN;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_OUT;
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOD, &GPIO_InitStructure);
#ifdef BUZZER
{
RCC_AHB1PeriphClockCmd( RCC_AHB1Periph_GPIOD, ENABLE);
GPIO_InitStructure.GPIO_Pin = BEEP_PIN;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_2MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_OUT;
GPIO_InitStructure.GPIO_OType = GPIO_OType_OD;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_DOWN;
GPIO_Init(GPIOD, &GPIO_InitStructure);
};
#endif
// uint8_t gpio_count = sizeof(gpio_cfg) / sizeof(gpio_cfg[0]);
// This is needed because some shit inside Keil startup f***s with SystemCoreClock, setting it back to 72MHz even on HSI.
//SystemCoreClockUpdate();
SystemInit();
// Turn on clocks for stuff we use
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM2 | RCC_APB1Periph_TIM3 | RCC_APB1Periph_TIM4 | RCC_APB1Periph_TIM5 | RCC_APB1Periph_I2C2 | RCC_APB1Periph_SPI2 | RCC_APB1Periph_USART2 | RCC_APB1Periph_USART3 , ENABLE);
RCC_APB2PeriphClockCmd( RCC_APB2Periph_TIM1 | RCC_APB2Periph_TIM8 | RCC_APB2Periph_ADC1 | RCC_APB2Periph_USART1 | RCC_APB2Periph_SPI1, ENABLE);
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOA | RCC_AHB1Periph_GPIOB | RCC_AHB1Periph_GPIOC | RCC_AHB1Periph_GPIOD | RCC_AHB1Periph_GPIOE | RCC_AHB1Periph_DMA2, ENABLE);
RCC_ClearFlag();
/*/ Make all GPIO in by default to save power and reduce noise
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_All;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AIN;
GPIO_Init(GPIOA, &GPIO_InitStructure);
GPIO_Init(GPIOB, &GPIO_InitStructure);
GPIO_Init(GPIOC, &GPIO_InitStructure);
// Turn off JTAG port 'cause we're using the GPIO for leds
GPIO_PinRemapConfig(GPIO_Remap_SWJ_JTAGDisable, ENABLE);
// Configure gpio
for (i = 0; i < gpio_count; i++) {
GPIO_InitStructure.GPIO_Pin = gpio_cfg[i].pin;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_2MHz;
GPIO_InitStructure.GPIO_Mode = gpio_cfg[i].mode;
GPIO_Init(gpio_cfg[i].gpio, &GPIO_InitStructure);
}*/
LED0_ON;
LED1_ON;
//LED2_OFF;
//LED3_OFF;
BEEP_OFF;
// Init cycle counter
cycleCounterInit();
// SysTick
SysTick_Config(SystemCoreClock / 1000);
// Configure the rest of the stuff
#ifndef FY90Q
i2cInit(I2C2);
#endif
//spiInit();
// sleep for 100ms
delay(100);
}
void systemInit(void)
{
RCC_ClocksTypeDef rccClocks;
///////////////////////////////////
// Init cycle counter
cycleCounterInit();
// SysTick
SysTick_Config(SystemCoreClock / 1000);
// Turn on peripherial clcoks
RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1, ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC2, ENABLE);
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_DMA1, ENABLE);
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_DMA2, ENABLE);
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOA, ENABLE);
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOB, ENABLE);
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOC, ENABLE);
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOD, ENABLE);
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOE, ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_I2C1, ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_I2C2, ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_SPI2, ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_SPI3, ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM1, ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM2, ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM3, ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM4, ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM5, ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM6, ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM8, ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM10, ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM11, ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1, ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_USART2, ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_USART3, ENABLE);
///////////////////////////////////
checkFirstTime(false);
readEEPROM();
if (eepromConfig.receiverType == SPEKTRUM)
checkSpektrumBind();
checkResetType();
NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2); // 2 bits for pre-emption priority, 2 bits for subpriority
///////////////////////////////////
gpsPortClearBuffer = &uart2ClearBuffer;
gpsPortNumCharsAvailable = &uart2NumCharsAvailable;
gpsPortPrintBinary = &uart2PrintBinary;
gpsPortRead = &uart2Read;
telemPortAvailable = &uart1Available;
telemPortPrint = &uart1Print;
telemPortPrintF = &uart1PrintF;
telemPortRead = &uart1Read;
///////////////////////////////////
initMixer();
usbInit();
ledInit();
uart1Init();
uart2Init();
BLUE_LED_ON;
///////////////////////////////////
delay(10000); // 10 seconds of 20 second delay for sensor stabilization
checkUsbActive();
#ifdef __VERSION__
cliPortPrintF("\ngcc version " __VERSION__ "\n");
#endif
cliPortPrintF("\nAQ32Plus Firmware V%s, Build Date " __DATE__ " "__TIME__" \n", __AQ32PLUS_VERSION);
if ((RCC->CR & RCC_CR_HSERDY) != RESET)
{
cliPortPrint("\nRunning on external HSE clock....\n");
}
else
{
cliPortPrint("\nERROR: Running on internal HSI clock....\n");
}
RCC_GetClocksFreq(&rccClocks);
cliPortPrintF("\nHCLK-> %3d MHz\n", rccClocks.HCLK_Frequency / 1000000);
cliPortPrintF( "PCLK1-> %3d MHz\n", rccClocks.PCLK1_Frequency / 1000000);
cliPortPrintF( "PCLK2-> %3d MHz\n", rccClocks.PCLK2_Frequency / 1000000);
cliPortPrintF( "SYSCLK-> %3d MHz\n\n", rccClocks.SYSCLK_Frequency / 1000000);
initUBLOX();
delay(10000); // Remaining 10 seconds of 20 second delay for sensor stabilization - probably not long enough..
///////////////////////////////////
adcInit();
i2cInit(I2C1);
i2cInit(I2C2);
pwmServoInit();
rxInit();
spiInit(SPI2);
spiInit(SPI3);
timingFunctionsInit();
batteryInit();
initFirstOrderFilter();
initMavlink();
initMax7456();
initPID();
GREEN_LED_ON;
initMPU6000();
initMag();
initPressure();
}
void systemInit(void)
{
// Init cycle counter
cycleCounterInit();
// SysTick
SysTick_Config(SystemCoreClock / 1000);
// Turn on peripherial clocks
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_ADC12, ENABLE);
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA1, ENABLE); // USART1
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA2, ENABLE); // ADC2
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOA, ENABLE);
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOB, ENABLE);
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOC, ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_SPI2, ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM2, ENABLE); // PWM Servo Out 1 & 2
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM3, ENABLE); // PWM ESC Out 3 & 4
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM4, ENABLE); // PWM ESC Out 5,6,7, & 8
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM6, ENABLE); // 500 Hz dt Counter
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM7, ENABLE); // 100 Hz dt Counter
RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM15, ENABLE); // PWM ESC Out 1 & 2
RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM16, ENABLE); // PPM RX
RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM17, ENABLE); // Spektrum Frame Sync
RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1, ENABLE); // Telemetry
RCC_APB1PeriphClockCmd(RCC_APB1Periph_USART3, ENABLE); // Spektrum RX
///////////////////////////////////////////////////////////////////////////
checkFirstTime(false);
readEEPROM();
if (eepromConfig.receiverType == SPEKTRUM)
checkSpektrumBind();
checkResetType();
NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2); // 2 bits for pre-emption priority, 2 bits for subpriority
initMixer();
cliInit();
gpioInit();
telemetryInit();
adcInit();
LED0_OFF;
delay(20000); // 20 sec total delay for sensor stabilization - probably not long enough.....
LED0_ON;
batteryInit();
pwmServoInit(eepromConfig.servoPwmRate);
if (eepromConfig.receiverType == SPEKTRUM)
spektrumInit();
else
ppmRxInit();
spiInit(SPI2);
timingFunctionsInit();
initFirstOrderFilter();
initPID();
initMPU6000();
initMag();
initPressure();
}
void systemInit(bool overclock)
{
//RCC_ClocksTypeDef rccClocks;
int i;
// start fpu
SCB->CPACR = (0x3 << (10 * 2)) | (0x3 << (11 * 2));
/* Reset the RCC clock configuration to the default reset state ------------*/
/* Set HSION bit */
RCC->CR |= (uint32_t)0x00000001;
/* Reset CFGR register */
RCC->CFGR = 0x00000000;
/* Reset HSEON, CSSON and PLLON bits */
RCC->CR &= (uint32_t)0xFEF6FFFF;
/* Reset PLLCFGR register */
RCC->PLLCFGR = 0x24003010;
/* Reset HSEBYP bit */
RCC->CR &= (uint32_t)0xFFFBFFFF;
/* Disable all interrupts */
RCC->CIR = 0x00000000;
#ifdef DATA_IN_ExtSRAM
SystemInit_ExtMemCtl();
#endif /* DATA_IN_ExtSRAM */
/* Configure the System clock source, PLL Multiplier and Divider factors,
AHB/APBx prescalers and Flash settings ----------------------------------*/
SetSysClock();
#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field.
/* Configure the Vector Table location add offset address ------------------*/
#ifdef VECT_TAB_SRAM
SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
#else
SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
#endif
// Init cycle counter
cycleCounterInit();
// SysTick
SysTick_Config(SystemCoreClock / 1000);
// RCC_ADCCLKConfig(RCC_ADC12PLLCLK_Div256); // 72 MHz divided by 256 = 281.25 kHz
// Turn on peripherial clocks
// RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_ADC12, ENABLE);
// RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_DMA1, ENABLE); // USART1, USART2
// RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_DMA2, ENABLE); // ADC2
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOA, ENABLE);
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOB, ENABLE);
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOC, ENABLE);
// RCC_APB1PeriphClockCmd(RCC_APB1Periph_SPI2, ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_SPI1, ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM1, ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM2, ENABLE); // PWM Out + PWM RX
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM3, ENABLE); // PWM Out
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM4, ENABLE); // PWM Out + PWM RX
RCC_APB1PeriphClockCmd(RCC_APB1Periph_I2C3, ENABLE); // i2c
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM5, ENABLE); //
RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM8, ENABLE); //
RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM10, ENABLE); //
RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM11, ENABLE); //
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM12, ENABLE); //
// RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM7, ENABLE); //
//
// PPM + PWM RX
// RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM8, ENABLE); //
// RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM15, ENABLE); // PWM Out
// RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM16, ENABLE); // PWM Out
// RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM17, ENABLE); // PWM Out
// RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1, ENABLE); // Telemetry
// RCC_APB1PeriphClockCmd(RCC_APB1Periph_USART2, ENABLE); // GPS
// RCC_APB1PeriphClockCmd(RCC_APB1Periph_USART3, ENABLE); // Spektrum RX
RCC_ClearFlag();
NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2); // 2 bits for pre-emption priority, 2 bits for subpriority
gpioStart();
spiInit();
// if feature(FEATURE_I2C)
// i2cInit(I2C2);
for (i = 0; i < 10; i++) {
LED0_TOGGLE
delay(25);
BEEP_ON
delay(25);
BEEP_OFF
}
LED0_OFF
}
void systemInit(void)
{
RCC_ClocksTypeDef rccClocks;
///////////////////////////////////
// Init cycle counter
cycleCounterInit();
// SysTick
SysTick_Config(SystemCoreClock / 1000);
// Turn on peripherial clocks
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_ADC12, ENABLE);
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA1, ENABLE); // USART1, USART2
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA2, ENABLE); // ADC2
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOA, ENABLE);
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOB, ENABLE);
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOC, ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_SPI2, ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM1, ENABLE); // PPM RX
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM2, ENABLE); // PWM ESC Out 1 & 2
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM3, ENABLE); // PWM ESC Out 5 & 6
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM4, ENABLE); // PWM Servo Out 1, 2, 3, & 4
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM6, ENABLE); // 500 Hz dt Counter
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM7, ENABLE); // 100 Hz dt Counter
RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM15, ENABLE); // PWM ESC Out 3 & 4
RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM16, ENABLE); // RangeFinder PWM
RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM17, ENABLE); // Spektrum Frame Sync
RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1, ENABLE); // Telemetry
RCC_APB1PeriphClockCmd(RCC_APB1Periph_USART2, ENABLE); // GPS
RCC_APB1PeriphClockCmd(RCC_APB1Periph_USART3, ENABLE); // Spektrum RX
///////////////////////////////////////////////////////////////////////////
spiInit(SPI2);
///////////////////////////////////
checkSensorEEPROM(false);
checkSystemEEPROM(false);
readSensorEEPROM();
readSystemEEPROM();
///////////////////////////////////
if (systemConfig.receiverType == SPEKTRUM)
checkSpektrumBind();
///////////////////////////////////
checkResetType();
NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2); // 2 bits for pre-emption priority, 2 bits for subpriority
///////////////////////////////////
gpsPortClearBuffer = &uart2ClearBuffer;
gpsPortNumCharsAvailable = &uart2NumCharsAvailable;
gpsPortPrintBinary = &uart2PrintBinary;
gpsPortRead = &uart2Read;
telemPortAvailable = &uart1Available;
telemPortPrint = &uart1Print;
telemPortPrintF = &uart1PrintF;
telemPortRead = &uart1Read;
///////////////////////////////////
initMixer();
usbInit();
gpioInit();
uart1Init();
uart2Init();
LED0_OFF;
delay(10000); // 10 seconds of 20 second delay for sensor stabilization
checkUsbActive();
///////////////////////////////////
#ifdef __VERSION__
cliPortPrintF("\ngcc version " __VERSION__ "\n");
#endif
cliPortPrintF("\nFF32mini Firmware V%s, Build Date " __DATE__ " "__TIME__" \n", __FF32MINI_VERSION);
if ((RCC->CR & RCC_CR_HSERDY) != RESET)
{
cliPortPrint("\nRunning on external HSE clock....\n");
}
else
{
cliPortPrint("\nERROR: Running on internal HSI clock....\n");
}
RCC_GetClocksFreq(&rccClocks);
cliPortPrintF("\nHCLK-> %2d MHz\n", rccClocks.HCLK_Frequency / 1000000);
cliPortPrintF( "PCLK1-> %2d MHz\n", rccClocks.PCLK1_Frequency / 1000000);
cliPortPrintF( "PCLK2-> %2d MHz\n", rccClocks.PCLK2_Frequency / 1000000);
cliPortPrintF( "SYSCLK-> %2d MHz\n\n", rccClocks.SYSCLK_Frequency / 1000000);
if (systemConfig.receiverType == PPM)
cliPortPrint("Using PPM Receiver....\n\n");
else
cliPortPrint("Using Spektrum Satellite Receiver....\n\n");
initUBLOX();
delay(10000); // Remaining 10 seconds of 20 second delay for sensor stabilization - probably not long enough..
///////////////////////////////////
adcInit();
aglInit();
pwmServoInit();
if (systemConfig.receiverType == SPEKTRUM)
spektrumInit();
else
ppmRxInit();
timingFunctionsInit();
batteryInit();
initFirstOrderFilter();
initMavlink();
initPID();
LED0_ON;
initMPU6000();
initMag();
initPressure();
}
void systemInit(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
// Turn on clocks for stuff we use
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA | RCC_APB2Periph_GPIOB | RCC_APB2Periph_GPIOC | RCC_APB2Periph_AFIO, ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM1, ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM2, ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM3, ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM4, ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1, ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1, ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_I2C2, ENABLE);
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA1, ENABLE);
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA2, ENABLE);
RCC_ClearFlag();
// Make all GPIO in by default to save power and reduce noise
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_All;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AIN;
GPIO_Init(GPIOA, &GPIO_InitStructure);
GPIO_Init(GPIOB, &GPIO_InitStructure);
GPIO_Init(GPIOC, &GPIO_InitStructure);
// Turn off JTAG port 'cause we're using the GPIO for leds
GPIO_PinRemapConfig(GPIO_Remap_SWJ_JTAGDisable, ENABLE);
// Init cycle counter
cycleCounterInit();
// SysTick
SysTick_Config(SystemCoreClock / 1000);
NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2); // 2 bits for pre-emption priority, 2 bits for subpriority
checkFirstTime(false);
readEEPROM();
ledInit();
LED0_ON;
initMixer();
pwmOutputConfig.escPwmRate = eepromConfig.escPwmRate;
pwmOutputConfig.servoPwmRate = eepromConfig.servoPwmRate;
cliInit(115200);
i2cInit(I2C2);
pwmOutputInit(&pwmOutputConfig);
rxInit();
delay(20000); // 20 sec delay for sensor stabilization - probably not long enough.....
LED1_ON;
initAccel();
initGyro();
initMag();
initPressure();
initPID();
}
int main(void)
{
u8 i;
u8 RecvBuf[32];
u8 SendBuf[32];
u8 offline = 0;
u8 recv_flag = 0;
u32 pd2ms=0,pd20ams=0,pd20bms=0,pd100ms=0;
SystemInit();
RCC_Configuration();
NVIC_Configuration();
GPIO_Configuration();
USART1_Configuration();
dbgPrintf(" Init Ticktack !\r\n");
cycleCounterInit();
SysTick_Config(SystemCoreClock / 1000);
for(i=0;i<2;i++)
{
OP_LED1;OP_LED2;OP_LED3;OP_LED4;
delay_ms(500);
OP_LED1;OP_LED2;OP_LED3;OP_LED4;
delay_ms(500);
}
FilterInit();
controllerInit();
dbgPrintf(" Init eeprom!\r\n");
FLASH_Unlock();
EE_Init();
EE_Read_ACC_GYRO_Offset();
/* 如果PID丢失或者错误，将下面两行注释去掉，重新编译烧写，运行一遍，可将PID还原，然后重新注释，再烧写一遍 */
//EE_Write_PID();
//EE_Write_Rate_PID();
EE_Read_PID();
EE_Read_Rate_PID();
dbgPrintf(" Init adc!\r\n");
ADC_DMA_Init();
dbgPrintf(" Init NRF24L01 !\r\n");
SPI_NRF_Init();
Nrf24l01_Init();
NRF24l01_SetRxMode();
while(Nrf24l01_Check())
{
dbgPrintf("NRF24L01 Fault !\r\n");
delay_ms(500);
}
dbgPrintf("NRF24L01 Is Detected !\r\n");
dbgPrintf("Init MPU6050...\r\n");
IIC_Init();
MPU6050_initialize();
dbgPrintf("Init Motor...\r\n");
Motor_Init();
Motor_SetPwm(0,0,0,0);
pd20bms = TIMIRQCNT + 10*ITS_PER_MS;
while(1)
{
if(TIMIRQCNT>pd2ms + 2*ITS_PER_MS-1) // every 4ms
{
GetEulerAngle();
if(lock_flag==UNLOCK)
AttitudeToMotors(angle.y,angle.x,angle.z);
else
{
MOTOR1=0;
MOTOR2=0;
MOTOR3=0;
MOTOR4=0;
}
Motor_SetPwm(MOTOR1,MOTOR2,MOTOR3,MOTOR4);
pd2ms = TIMIRQCNT;
}
if(TIMIRQCNT>pd20ams + 20*ITS_PER_MS-1) // every 20ms
{
if(NRF24l01_Recv(RecvBuf)>10)
{
if((RecvBuf[RecvBuf[2]+3]==CheckSum(RecvBuf, RecvBuf[2]+3))&&(RecvBuf[0]==0xAA))
{
if(RecvBuf[1]!=0xC0)
OP_LED1;
offline=0;
switch(RecvBuf[1])
{
case 0xC0: //control
Getdesireddata(RecvBuf);
OP_LED2;
break;
case 0x10: //W PID
SetPID(RecvBuf);
break;
case 0x11: //W Attitude
SetAccGyroOffset(RecvBuf);
break;
case 0x12: //W Control offset
break;
case 0x14: //W Rate PID
SetRatePID(RecvBuf);
break;
case 0x20: //R PID
recv_flag = RESEND;
GetPID(SendBuf);
break;
case 0x21: //R Attitude
recv_flag = RESEND;
GetAccGyroOffset(SendBuf);
break;
case 0x22: //R Control offset
break;
case 0x24: //R Rate PID
recv_flag = RESEND;
GetRatePID(SendBuf);
break;
case 0x40: //校准姿态
EnableCalibration();
break;
case 0x41: //校准遥控器零点
break;
default:
break;
}
}
}
pd20ams = TIMIRQCNT;
}
if(TIMIRQCNT>pd20bms + 20*ITS_PER_MS-1) // every 20ms
{
if(recv_flag==0)
GetState(SendBuf);
else
recv_flag--;
NRF_SendData(SendBuf);
OP_LED3;
pd20bms = TIMIRQCNT;
}
if(TIMIRQCNT>pd100ms + 100*ITS_PER_MS-1) // every 100ms
{
if(offline>20)
lock_flag = LOCK;
offline++;
// OP_LED4;
pd100ms = TIMIRQCNT;
}
}
}
