static uint16_t sendto_interrupt(struct net_driver_s *dev, void *conn,
void *pvpriv, uint16_t flags)
{
FAR struct sendto_s *pstate = (FAR struct sendto_s *)pvpriv;
nllvdbg("flags: %04x\n", flags);
if (pstate)
{
/* Check if the outgoing packet is available. It may have been claimed
* by a sendto interrupt serving a different thread -OR- if the output
* buffer currently contains unprocessed incoming data. In these cases
* we will just have to wait for the next polling cycle.
*/
if (dev->d_sndlen > 0 || (flags & UDP_NEWDATA) != 0)
{
/* Another thread has beat us sending data or the buffer is busy,
* Check for a timeout. If not timed out, wait for the next
* polling cycle and check again.
*/
#ifdef CONFIG_NET_SENDTO_TIMEOUT
if (send_timeout(pstate))
{
/* Yes.. report the timeout */
nlldbg("SEND timeout\n");
pstate->st_sndlen = -ETIMEDOUT;
}
else
#endif /* CONFIG_NET_SENDTO_TIMEOUT */
{
/* No timeout. Just wait for the next polling cycle */
return flags;
}
}
/* It looks like we are good to send the data */
else
{
/* Copy the user data into d_snddata and send it */
devif_send(dev, pstate->st_buffer, pstate->st_buflen);
pstate->st_sndlen = pstate->st_buflen;
}
/* Don't allow any further call backs. */
pstate->st_cb->flags = 0;
pstate->st_cb->priv = NULL;
pstate->st_cb->event = NULL;
/* Wake up the waiting thread */
sem_post(&pstate->st_sem);
}
return flags;
}
static uint16_t tcpsend_interrupt(FAR struct net_driver_s *dev,
FAR void *pvconn,
FAR void *pvpriv, uint16_t flags)
{
FAR struct tcp_conn_s *conn = (FAR struct tcp_conn_s *)pvconn;
FAR struct send_s *pstate = (FAR struct send_s *)pvpriv;
#ifdef CONFIG_NETDEV_MULTINIC
/* The TCP socket is connected and, hence, should be bound to a device.
* Make sure that the polling device is the one that we are bound to.
*/
DEBUGASSERT(conn->dev != NULL);
if (dev != conn->dev)
{
return flags;
}
#endif
nllvdbg("flags: %04x acked: %d sent: %d\n",
flags, pstate->snd_acked, pstate->snd_sent);
/* If this packet contains an acknowledgement, then update the count of
* acknowledged bytes.
*/
if ((flags & TCP_ACKDATA) != 0)
{
FAR struct tcp_hdr_s *tcp;
/* Update the timeout */
#ifdef CONFIG_NET_SOCKOPTS
pstate->snd_time = clock_systimer();
#endif
/* Get the offset address of the TCP header */
#ifdef CONFIG_NET_IPv4
#ifdef CONFIG_NET_IPv6
if (conn->domain == PF_INET)
#endif
{
DEBUGASSERT(IFF_IS_IPv4(dev->d_flags));
tcp = TCPIPv4BUF;
}
#endif /* CONFIG_NET_IPv4 */
#ifdef CONFIG_NET_IPv6
#ifdef CONFIG_NET_IPv4
else
#endif
{
DEBUGASSERT(IFF_IS_IPv6(dev->d_flags));
tcp = TCPIPv6BUF;
}
#endif /* CONFIG_NET_IPv6 */
/* The current acknowledgement number number is the (relative) offset
* of the of the next byte needed by the receiver. The snd_isn is the
* offset of the first byte to send to the receiver. The difference
* is the number of bytes to be acknowledged.
*/
pstate->snd_acked = tcp_getsequence(tcp->ackno) - pstate->snd_isn;
nllvdbg("ACK: acked=%d sent=%d buflen=%d\n",
pstate->snd_acked, pstate->snd_sent, pstate->snd_buflen);
/* Have all of the bytes in the buffer been sent and acknowledged? */
if (pstate->snd_acked >= pstate->snd_buflen)
{
/* Yes. Then pstate->snd_buflen should hold the number of bytes
* actually sent.
*/
goto end_wait;
}
/* No.. fall through to send more data if necessary */
}
/* Check if we are being asked to retransmit data */
else if ((flags & TCP_REXMIT) != 0)
{
/* Yes.. in this case, reset the number of bytes that have been sent
* to the number of bytes that have been ACKed.
*/
pstate->snd_sent = pstate->snd_acked;
#if defined(CONFIG_NET_TCP_SPLIT)
/* Reset the even/odd indicator to even since we need to
* retransmit.
*/
pstate->snd_odd = false;
#endif
/* Fall through to re-send data from the last that was ACKed */
}
/* Check for a loss of connection */
else if ((flags & TCP_DISCONN_EVENTS) != 0)
{
/* Report not connected */
nllvdbg("Lost connection\n");
net_lostconnection(pstate->snd_sock, flags);
pstate->snd_sent = -ENOTCONN;
goto end_wait;
}
/* Check if the outgoing packet is available (it may have been claimed
* by a sendto interrupt serving a different thread).
*/
#if 0 /* We can't really support multiple senders on the same TCP socket */
else if (dev->d_sndlen > 0)
{
/* Another thread has beat us sending data, wait for the next poll */
return flags;
}
#endif
/* We get here if (1) not all of the data has been ACKed, (2) we have been
* asked to retransmit data, (3) the connection is still healthy, and (4)
* the outgoing packet is available for our use. In this case, we are
* now free to send more data to receiver -- UNLESS the buffer contains
* unprocessed incoming data. In that event, we will have to wait for the
* next polling cycle.
*/
if ((flags & TCP_NEWDATA) == 0 && pstate->snd_sent < pstate->snd_buflen)
{
uint32_t seqno;
/* Get the amount of data that we can send in the next packet */
uint32_t sndlen = pstate->snd_buflen - pstate->snd_sent;
#if defined(CONFIG_NET_TCP_SPLIT)
/* RFC 1122 states that a host may delay ACKing for up to 500ms but
* must respond to every second segment). This logic here will trick
* the RFC 1122 recipient into responding sooner. This logic will be
* activated if:
*
* 1. An even number of packets has been send (where zero is an even
* number),
* 2. There is more data be sent (more than or equal to
* CONFIG_NET_TCP_SPLIT_SIZE), but
* 3. Not enough data for two packets.
*
* Then we will split the remaining, single packet into two partial
* packets. This will stimulate the RFC 1122 peer to ACK sooner.
*
* Don't try to split very small packets (less than CONFIG_NET_TCP_SPLIT_SIZE).
* Only the first even packet and the last odd packets could have
* sndlen less than CONFIG_NET_TCP_SPLIT_SIZE. The value of sndlen on
* the last even packet is guaranteed to be at least MSS/2 by the
* logic below.
*/
if (sndlen >= CONFIG_NET_TCP_SPLIT_SIZE)
{
/* sndlen is the number of bytes remaining to be sent.
* conn->mss will provide the number of bytes that can sent
* in one packet. The difference, then, is the number of bytes
* that would be sent in the next packet after this one.
*/
int32_t next_sndlen = sndlen - conn->mss;
/* Is this the even packet in the packet pair transaction? */
if (!pstate->snd_odd)
{
/* next_sndlen <= 0 means that the entire remaining data
* could fit into this single packet. This is condition
* in which we must do the split.
*/
if (next_sndlen <= 0)
{
/* Split so that there will be an odd packet. Here
* we know that 0 < sndlen <= MSS
*/
sndlen = (sndlen / 2) + 1;
}
}
/* No... this is the odd packet in the packet pair transaction */
else
{
/* Will there be another (even) packet afer this one?
* (next_sndlen > 0) Will the split condition occur on that
* next, even packet? ((next_sndlen - conn->mss) < 0) If
* so, then perform the split now to avoid the case where the
* byte count is less than CONFIG_NET_TCP_SPLIT_SIZE on the
* next pair.
*/
if (next_sndlen > 0 && (next_sndlen - conn->mss) < 0)
{
/* Here, we know that sndlen must be MSS < sndlen <= 2*MSS
* and so (sndlen / 2) is <= MSS.
*/
sndlen /= 2;
}
}
}
/* Toggle the even/odd indicator */
pstate->snd_odd ^= true;
#endif /* CONFIG_NET_TCP_SPLIT */
if (sndlen > conn->mss)
{
sndlen = conn->mss;
}
/* Check if we have "space" in the window */
if ((pstate->snd_sent - pstate->snd_acked + sndlen) < conn->winsize)
{
/* Set the sequence number for this packet. NOTE: The network updates
* sndseq on receipt of ACK *before* this function is called. In that
* case sndseq will point to the next unacknowledged byte (which might
* have already been sent). We will overwrite the value of sndseq
* here before the packet is sent.
*/
seqno = pstate->snd_sent + pstate->snd_isn;
nllvdbg("SEND: sndseq %08x->%08x\n", conn->sndseq, seqno);
tcp_setsequence(conn->sndseq, seqno);
#ifdef NEED_IPDOMAIN_SUPPORT
/* If both IPv4 and IPv6 support are enabled, then we will need to
* select which one to use when generating the outgoing packet.
* If only one domain is selected, then the setup is already in
* place and we need do nothing.
*/
tcpsend_ipselect(dev, pstate);
#endif
/* Then set-up to send that amount of data. (this won't actually
* happen until the polling cycle completes).
*/
devif_send(dev, &pstate->snd_buffer[pstate->snd_sent], sndlen);
/* Check if the destination IP address is in the ARP or Neighbor
* table. If not, then the send won't actually make it out... it
* will be replaced with an ARP request or Neighbor Solicitation.
*/
if (pstate->snd_sent != 0 || psock_send_addrchck(conn))
{
/* Update the amount of data sent (but not necessarily ACKed) */
pstate->snd_sent += sndlen;
nllvdbg("SEND: acked=%d sent=%d buflen=%d\n",
pstate->snd_acked, pstate->snd_sent, pstate->snd_buflen);
}
}
}
#ifdef CONFIG_NET_SOCKOPTS
/* All data has been sent and we are just waiting for ACK or re-transmit
* indications to complete the send. Check for a timeout.
*/
if (send_timeout(pstate))
{
/* Yes.. report the timeout */
nlldbg("SEND timeout\n");
pstate->snd_sent = -ETIMEDOUT;
goto end_wait;
}
#endif /* CONFIG_NET_SOCKOPTS */
/* Continue waiting */
return flags;
end_wait:
/* Do not allow any further callbacks */
pstate->snd_cb->flags = 0;
pstate->snd_cb->priv = NULL;
pstate->snd_cb->event = NULL;
/* There are no outstanding, unacknowledged bytes */
conn->unacked = 0;
/* Wake up the waiting thread */
sem_post(&pstate->snd_sem);
return flags;
}
static uint16_t sendto_interrupt(FAR struct net_driver_s *dev, FAR void *conn,
FAR void *pvpriv, uint16_t flags)
{
FAR struct sendto_s *pstate = (FAR struct sendto_s *)pvpriv;
nllvdbg("flags: %04x\n", flags);
if (pstate)
{
/* If the network device has gone down, then we will have terminate
* the wait now with an error.
*/
if ((flags & NETDEV_DOWN) != 0)
{
/* Terminate the transfer with an error. */
nlldbg("ERROR: Network is down\n");
pstate->st_sndlen = -ENETUNREACH;
}
/* Check if the outgoing packet is available. It may have been claimed
* by a sendto interrupt serving a different thread -OR- if the output
* buffer currently contains unprocessed incoming data. In these cases
* we will just have to wait for the next polling cycle.
*/
else if (dev->d_sndlen > 0 || (flags & UDP_NEWDATA) != 0)
{
/* Another thread has beat us sending data or the buffer is busy,
* Check for a timeout. If not timed out, wait for the next
* polling cycle and check again.
*/
#ifdef CONFIG_NET_SENDTO_TIMEOUT
if (send_timeout(pstate))
{
/* Yes.. report the timeout */
nlldbg("ERROR: SEND timeout\n");
pstate->st_sndlen = -ETIMEDOUT;
}
else
#endif /* CONFIG_NET_SENDTO_TIMEOUT */
{
/* No timeout. Just wait for the next polling cycle */
return flags;
}
}
/* It looks like we are good to send the data */
else
{
#ifdef NEED_IPDOMAIN_SUPPORT
/* If both IPv4 and IPv6 support are enabled, then we will need to
* select which one to use when generating the outgoing packet.
* If only one domain is selected, then the setup is already in
* place and we need do nothing.
*/
sendto_ipselect(dev, pstate);
#endif
/* Copy the user data into d_appdata and send it */
devif_send(dev, pstate->st_buffer, pstate->st_buflen);
pstate->st_sndlen = pstate->st_buflen;
}
/* Don't allow any further call backs. */
pstate->st_cb->flags = 0;
pstate->st_cb->priv = NULL;
pstate->st_cb->event = NULL;
/* Wake up the waiting thread */
sem_post(&pstate->st_sem);
}
return flags;
}
