void dfll_enable_config_defaults(unsigned int dfll_id)
{
struct dfll_config dfllcfg;
if (dfll_is_fine_locked(dfll_id)) {
return; // DFLL already running
}
switch (dfll_id) {
#ifdef CONFIG_DFLL0_SOURCE
case 0:
dfll_enable_source(CONFIG_DFLL0_SOURCE);
dfll_config_init_closed_loop_mode(&dfllcfg,
CONFIG_DFLL0_SOURCE,
CONFIG_DFLL0_DIV,
CONFIG_DFLL0_MUL);
break;
#endif
default:
Assert(false);
break;
}
dfll_enable_closed_loop(&dfllcfg, dfll_id);
while (!dfll_is_fine_locked(dfll_id));
}
void dfll_enable_config_defaults(uint32_t dfll_id)
{
#ifdef CONFIG_DFLL0_SOURCE
struct dfll_config dfllcfg;
#endif
static bool open_loop_done = false;
if((SCIF->SCIF_DFLL0CONF & SCIF_DFLL0CONF_MODE) &&
(SCIF->SCIF_DFLL0CONF & SCIF_DFLL0CONF_EN)) {
// Closed-loop mode
if (dfll_is_fine_locked(dfll_id)) {
return; // DFLL already running
}
}
if (open_loop_done == true) {
return;
}
switch (dfll_id) {
#ifdef CONFIG_DFLL0_SOURCE
case 0:
dfll_enable_source(CONFIG_DFLL0_SOURCE);
dfll_config_init_closed_loop_mode(&dfllcfg,
CONFIG_DFLL0_SOURCE,
CONFIG_DFLL0_DIV,
CONFIG_DFLL0_MUL);
dfll_enable_closed_loop(&dfllcfg, dfll_id);
while (!dfll_is_fine_locked(dfll_id));
break;
#endif
default:
Assert(false);
break;
}
}
int main(void)
{
sysclk_init();
board_init();
/* Enable one wait state for flash access */
flashcalw_set_wait_state(1);
/*
* Configure systick for 200ms (CPU frequency / 5) at startup time.
*
* Note: CPU frequency will be changed with below clock switching.
*/
if (SysTick_Config(sysclk_get_cpu_hz() / 5)) {
while (1) { /* Capture error */
}
}
while (1) {
struct dfll_config dcfg;
struct pll_config pcfg;
/* avoid Cppcheck Warning */
UNUSED(pcfg);
/*
* Initial state: Running from RC80M with all
* prescalers set to 2 (Divide frequency by 4).
*/
wait_for_switches();
/*
* Divide CPU frequency by 8. This will make the LED
* blink half as fast.
*/
sysclk_set_prescalers(3, 3, 3, 3, 3);
wait_for_switches();
/*
* Switch to the DFLL running at ~48 MHz in Open Loop
* mode, with the CPU running at ~48 MHz.
*/
dfll_config_init_open_loop_mode(&dcfg);
dfll_config_tune_for_target_hz(&dcfg, 48000000);
dfll_enable_open_loop(&dcfg, 0);
sysclk_set_prescalers(1, 1, 1, 1, 1);
sysclk_set_source(SYSCLK_SRC_DFLL);
osc_disable(OSC_ID_RC80M);
wait_for_switches();
/*
* Switch to the slow clock with all prescalers
* disabled.
*/
sysclk_set_source(SYSCLK_SRC_RCSYS);
sysclk_set_prescalers(0, 0, 0, 0, 0);
dfll_disable_open_loop(0);
wait_for_switches();
/*
* Switch to the RCFAST clock with all prescalers
* disabled.
*/
osc_enable(OSC_ID_RCFAST);
sysclk_set_prescalers(0, 0, 0, 0, 0);
osc_wait_ready(OSC_ID_RCFAST);
sysclk_set_source(SYSCLK_SRC_RCFAST);
wait_for_switches();
/*
* Switch to the RC1M clock with all prescalers
* disabled.
*/
osc_enable(OSC_ID_RC1M);
sysclk_set_prescalers(0, 0, 0, 0, 0);
osc_wait_ready(OSC_ID_RC1M);
sysclk_set_source(SYSCLK_SRC_RC1M);
osc_disable(OSC_ID_RCFAST);
wait_for_switches();
/*
* Switch to external OSC0, if available.
*/
#ifdef BOARD_OSC0_HZ
osc_enable(OSC_ID_OSC0);
osc_wait_ready(OSC_ID_OSC0);
sysclk_set_source(SYSCLK_SRC_OSC0);
osc_disable(OSC_ID_RC1M);
wait_for_switches();
/*
* Switch to PLL0 running at 96 MHz. Use OSC0 as the
* source
*/
pll_config_init(&pcfg, PLL_SRC_OSC0, 1, 96000000 /
BOARD_OSC0_HZ);
pll_enable(&pcfg, 0);
sysclk_set_prescalers(2, 2, 2, 2, 2);
pll_wait_for_lock(0);
sysclk_set_source(SYSCLK_SRC_PLL0);
wait_for_switches();
#endif
/*
* Switch to the DFLL, using the 32 kHz oscillator as a
* reference if available, or failing that, the 115 kHz
* RCSYS oscillator.
*/
#ifdef BOARD_OSC32_HZ
osc_enable(OSC_ID_OSC32);
dfll_config_init_closed_loop_mode(&dcfg,
GENCLK_SRC_OSC32K, 1,
CONFIG_DFLL0_FREQ / BOARD_OSC32_HZ);
osc_wait_ready(OSC_ID_OSC32);
#else
dfll_config_init_closed_loop_mode(&dcfg,
GENCLK_SRC_RCSYS, 1,
CONFIG_DFLL0_FREQ / OSC_RCSYS_NOMINAL_HZ);
#endif
dfll_enable_closed_loop(&dcfg, 0);
sysclk_set_prescalers(1, 1, 1, 1, 1);
dfll_wait_for_fine_lock(0);
sysclk_set_source(SYSCLK_SRC_DFLL);
#ifdef BOARD_OSC0_HZ
osc_disable(OSC_ID_OSC0);
#endif
wait_for_switches();
/*
* Go back to the initial state and start over.
*/
osc_enable(OSC_ID_RC80M);
sysclk_set_prescalers(2, 2, 2, 2, 2);
osc_wait_ready(OSC_ID_RC80M);
sysclk_set_source(SYSCLK_SRC_RC80M);
dfll_disable_closed_loop(0);
#ifdef BOARD_OSC32_HZ
osc_disable(OSC_ID_OSC32);
#endif
}
}
