C++ (Cpp) enableStandbyMode Examples

Example #1

File: device.cpp Project: rmnzr/murmur

//--------------------------------------------------------------
void Device::setEnableStandbyMode(bool is)
{
    ofxOscMessage m;
    m.setAddress( OSC_ADDRESS_SET_DEVICE_PROP );
    m.addStringArg(m_id);
    m.addStringArg("enableStandbyMode");
    m.addIntArg(is ? 1 : 0);
    m_oscSender.sendMessage(m);

    enableStandbyMode(is);
}

Example #2

File: device.cpp Project: v3ga/murmur

//--------------------------------------------------------------
void Device::setEnableStandbyMode(bool is)
{
    enableStandbyMode(is);

	if (m_isSendMessagesOSC == false) return;

    ofxOscMessage m;
    m.setAddress( OSC_ADDRESS_SET_DEVICE_PROP );
    m.addStringArg(m_id);
    m.addStringArg("enableStandbyMode");
    m.addIntArg(is ? 1 : 0);
    m_oscSender.sendMessage(m);

	LOG_MESSAGE_OSC(m,false);
}

Example #3

File: nRF905.cpp Project: pventafridda/SoftRF

void nRF905_init()
{
#ifdef ARDUINO
    pinMode(TRX_EN, OUTPUT);
    pinMode(PWR_MODE, OUTPUT);
    pinMode(TX_EN, OUTPUT);

#if NRF905_COLLISION_AVOID
    pinMode(CD, INPUT);
#endif

#if AM_IS_USED_HW
    pinMode(AM, INPUT);
#endif

#if !NRF905_DR_SW
    pinMode(DR, INPUT);
#endif

    digitalWrite(CSN, HIGH);
    pinMode(CSN, OUTPUT);

    SPI.begin();
    SPI.setClockDivider(SPI_CLOCK_DIV2);
#else
    TRX_EN_DDR |= _BV(TRX_EN_BIT);
    PWR_MODE_DDR |= _BV(PWR_MODE_BIT);
    TX_EN_DDR |= _BV(TX_EN_BIT);

#if NRF905_COLLISION_AVOID
    CD_DDR &= ~_BV(CD_BIT);
#endif

#if AM_IS_USED_HW
    AM_DDR &= ~_BV(AM_BIT);
#endif

#if !NRF905_DR_SW
    DR_DDR &= ~_BV(DR_BIT);
#endif

    spiDeselect();
    CSN_DDR |= _BV(CSN_BIT);

    spi_init();
#endif

    radio.state = NRF905_RADIO_STATE_IDLE;

    // Startup
    enableStandbyMode();
    receiveMode();
    nRF905_powerDown();
    _delay_ms(3);
    defaultConfig();

#if NRF905_INTERRUPTS
    // Set interrupts
    REG_EXTERNAL_INT_CTL |= BIT_EXTERNAL_INT_CTL;
    nRF905_interrupt_on();
#endif

    nRF905_powerUp();
}

Example #4

File: device.cpp Project: v3ga/murmur

//--------------------------------------------------------------
void Device::setEnableStandbyModeOSC(bool is)
{
    enableStandbyMode(is);
}

Example #5

File: nRF905.c Project: giovannip/Arduino

void nRF905_init()
{
#ifdef ARDUINO
	pinMode(TRX_EN, OUTPUT);
	pinMode(PWR_MODE, OUTPUT);
	pinMode(TX_EN, OUTPUT);
	pinMode(CD, INPUT);
#if !NRF905_AM_SW
	pinMode(AM, INPUT);
#endif
#if !NRF905_DR_SW
	pinMode(DR, INPUT);
#endif

	pinMode(CSN, OUTPUT);
	digitalWrite(CSN, HIGH);

	SPI.begin();
	SPI.setClockDivider(SPI_CLOCK_DIV2);
#else
	TRX_EN_DDR |= (1<<TRX_EN_BIT);
	PWR_MODE_DDR |= (1<<PWR_MODE_BIT);
	TX_EN_DDR |= (1<<TX_EN_BIT);

	CD_DDR &= ~(1<<CD_BIT);
#if !NRF905_AM_SW
	AM_DDR &= ~(1<<AM_BIT);
#endif
#if !NRF905_DR_SW
	DR_DDR &= ~(1<<DR_BIT);
#endif

	spi_init();
#endif

	// Set default values
	config.reg1 = 0x00;
	config.reg2 = (0xC7 | NRF905_CLK_FREQ);
	config.payloadSize = NRF905_MAX_PAYLOAD;

#if NRF905_INTERRUPTS
	memset((byte*)rxBuffer, 0, sizeof(rxBuffer));
	gotData = false;

	// Set interrupts
	REG_EXTERNAL_INT_CTL |= BIT_EXTERNAL_INT_CTL;
	NRF905_INT_ON();
#endif

	// Startup
	nRF905_powerUp();
	receiveMode();
	enableStandbyMode();

//	config();

	// 4 byte TX and RX addresses
	setConfigRegister(NRF905_CMD_W_CONFIG | NRF905_REG_ADDR_WIDTH, 0b01000100);

	// Default config
	nRF905_setFrequency(NRF905_BAND_433, 433200000);
	nRF905_setAutoRetransmit(NRF905_AUTO_RETRAN_DISABLE);
	nRF905_setLowRxPower(NRF905_LOW_RX_DISABLE);
	nRF905_setTransmitPower(NRF905_PWR_10);
	nRF905_setCRCMode(NRF905_CRC_MODE_16);
	nRF905_setCRC(NRF905_CRC_ENABLE);
	nRF905_setClockOut(NRF905_OUTCLK_DISABLE);
	nRF905_setClockOutFreq(NRF905_OUTCLK_500KHZ);
	nRF905_setPayloadSize(NRF905_MAX_PAYLOAD);
	nRF905_setTXAddress(0xE7E7E7E7);
	nRF905_setRXAddress(0xE7E7E7E7);
}