static void
do_alias(int argc, char *argv[])
{
char name[80];
char *val;
struct config_option opt;
switch (argc) {
case 2:
make_alias(name, argv[1]);
if (flash_get_config(name, &val, CONFIG_STRING)) {
diag_printf("'%s' = '%s'\n", argv[1], val);
} else {
diag_printf("'%s' not found\n", argv[1]);
}
break;
case 3:
if (strlen(argv[2]) >= MAX_STRING_LENGTH) {
diag_printf("Sorry, value is too long\n");
break;
}
make_alias(name, argv[1]);
opt.type = CONFIG_STRING;
opt.enable = (char *)0;
opt.enable_sense = 1;
opt.key = name;
opt.dflt = (CYG_ADDRESS)argv[2];
flash_add_config(&opt, true);
break;
default:
diag_printf("usage: alias name [value]\n");
}
}
void
do_baud_rate(int argc, char *argv[])
{
int new_rate, ret, old_rate;
bool new_rate_set;
hal_virtual_comm_table_t *__chan;
struct option_info opts[1];
#ifdef CYGSEM_REDBOOT_FLASH_CONFIG
struct config_option opt;
#endif
init_opts(&opts[0], 'b', true, OPTION_ARG_TYPE_NUM,
(void **)&new_rate, (bool *)&new_rate_set, "new baud rate");
if (!scan_opts(argc, argv, 1, opts, 1, 0, 0, "")) {
return;
}
__chan = CYGACC_CALL_IF_CONSOLE_PROCS();
if (new_rate_set) {
diag_printf("Baud rate will be changed to %d - update your settings\n", new_rate);
_sleep(500); // Give serial time to flush
old_rate = CYGACC_COMM_IF_CONTROL(*__chan, __COMMCTL_GETBAUD);
ret = set_console_baud_rate(new_rate);
if (ret < 0) {
if (old_rate > 0) {
// Try to restore
set_console_baud_rate(old_rate);
_sleep(500); // Give serial time to flush
diag_printf("\nret = %d\n", ret);
}
return; // Couldn't set the desired rate
}
old_rate = ret;
// Make sure this new rate works or back off to previous value
// Sleep for a few seconds, then prompt to see if it works
_sleep(3000); // Give serial time to flush
if (!verify_action_with_timeout(5000, "Baud rate changed to %d", new_rate)) {
_sleep(500); // Give serial time to flush
set_console_baud_rate(old_rate);
_sleep(500); // Give serial time to flush
return;
}
#ifdef CYGSEM_REDBOOT_FLASH_CONFIG
opt.type = CONFIG_INT;
opt.enable = (char *)0;
opt.enable_sense = 1;
opt.key = "console_baud_rate";
opt.dflt = new_rate;
flash_add_config(&opt, true);
#endif
} else {
ret = CYGACC_COMM_IF_CONTROL(*__chan, __COMMCTL_GETBAUD);
diag_printf("Baud rate = ");
if (ret <= 0) {
diag_printf("unknown\n");
} else {
diag_printf("%d\n", ret);
}
}
}
//
// Reset/initialize configuration data - used only when starting from scratch
//
static void
config_init(void)
{
// Well known option strings
struct config_option *optend = __CONFIG_options_TAB_END__;
struct config_option *opt = __CONFIG_options_TAB__;
memset(config, 0, sizeof(struct _config));
while (opt != optend) {
if (!flash_add_config(opt, false)) {
return;
}
opt++;
}
config_ok = true;
}
