static void __init h2_init(void)
{
h2_init_smc91x();
/* Here we assume the NOR boot config: NOR on CS3 (possibly swapped
* to address 0 by a dip switch), NAND on CS2B. The NAND driver will
* notice whether a NAND chip is enabled at probe time.
*
* FIXME revC boards (and H3) support NAND-boot, with a dip switch to
* put NOR on CS2B and NAND (which on H2 may be 16bit) on CS3. Try
* detecting that in code here, to avoid probing every possible flash
* configuration...
*/
h2_nor_resource.end = h2_nor_resource.start = omap_cs3_phys();
h2_nor_resource.end += SZ_32M - 1;
h2_nand_resource.end = h2_nand_resource.start = OMAP_CS2B_PHYS;
h2_nand_resource.end += SZ_4K - 1;
if (gpio_request(H2_NAND_RB_GPIO_PIN, "NAND ready") < 0)
BUG();
gpio_direction_input(H2_NAND_RB_GPIO_PIN);
omap_cfg_reg(L3_1610_FLASH_CS2B_OE);
omap_cfg_reg(M8_1610_FLASH_CS2B_WE);
/* MMC: card detect and WP */
/* omap_cfg_reg(U19_ARMIO1); */ /* CD */
omap_cfg_reg(BALLOUT_V8_ARMIO3); /* WP */
/* Mux pins for keypad */
omap_cfg_reg(F18_1610_KBC0);
omap_cfg_reg(D20_1610_KBC1);
omap_cfg_reg(D19_1610_KBC2);
omap_cfg_reg(E18_1610_KBC3);
omap_cfg_reg(C21_1610_KBC4);
omap_cfg_reg(G18_1610_KBR0);
omap_cfg_reg(F19_1610_KBR1);
omap_cfg_reg(H14_1610_KBR2);
omap_cfg_reg(E20_1610_KBR3);
omap_cfg_reg(E19_1610_KBR4);
omap_cfg_reg(N19_1610_KBR5);
/* GPIO based LEDs */
omap_cfg_reg(P18_1610_GPIO3);
omap_cfg_reg(MPUIO4);
h2_smc91x_resources[1].start = gpio_to_irq(0);
h2_smc91x_resources[1].end = gpio_to_irq(0);
platform_add_devices(h2_devices, ARRAY_SIZE(h2_devices));
omap_serial_init();
h2_i2c_board_info[0].irq = gpio_to_irq(58);
h2_i2c_board_info[1].irq = gpio_to_irq(2);
omap_register_i2c_bus(1, 100, h2_i2c_board_info,
ARRAY_SIZE(h2_i2c_board_info));
omap1_usb_init(&h2_usb_config);
h2_mmc_init();
omapfb_set_lcd_config(&h2_lcd_config);
}
static void __init h2_init(void)
{
/* Here we assume the NOR boot config: NOR on CS3 (possibly swapped
* to address 0 by a dip switch), NAND on CS2B. The NAND driver will
* notice whether a NAND chip is enabled at probe time.
*
* FIXME revC boards (and H3) support NAND-boot, with a dip switch to
* put NOR on CS2B and NAND (which on H2 may be 16bit) on CS3. Try
* detecting that in code here, to avoid probing every possible flash
* configuration...
*/
h2_nor_resource.end = h2_nor_resource.start = omap_cs3_phys();
h2_nor_resource.end += SZ_32M - 1;
h2_nand_resource.end = h2_nand_resource.start = OMAP_CS2B_PHYS;
h2_nand_resource.end += SZ_4K - 1;
if (!(omap_request_gpio(H2_NAND_RB_GPIO_PIN)))
h2_nand_data.dev_ready = h2_nand_dev_ready;
omap_cfg_reg(L3_1610_FLASH_CS2B_OE);
omap_cfg_reg(M8_1610_FLASH_CS2B_WE);
/* MMC: card detect and WP */
/* omap_cfg_reg(U19_ARMIO1); */ /* CD */
omap_cfg_reg(BALLOUT_V8_ARMIO3); /* WP */
/* Irda */
#if defined(CONFIG_OMAP_IR) || defined(CONFIG_OMAP_IR_MODULE)
omap_writel(omap_readl(FUNC_MUX_CTRL_A) | 7, FUNC_MUX_CTRL_A);
if (!(omap_request_gpio(H2_IRDA_FIRSEL_GPIO_PIN))) {
omap_set_gpio_direction(H2_IRDA_FIRSEL_GPIO_PIN, 0);
h2_irda_data.transceiver_mode = h2_transceiver_mode;
}
#endif
platform_add_devices(h2_devices, ARRAY_SIZE(h2_devices));
spi_register_board_info(h2_spi_board_info,
ARRAY_SIZE(h2_spi_board_info));
omap_board_config = h2_config;
omap_board_config_size = ARRAY_SIZE(h2_config);
omap_serial_init();
omap_register_i2c_bus(1, 100, h2_i2c_board_info,
ARRAY_SIZE(h2_i2c_board_info));
h2_mmc_init();
omap_register_gpio_switches(h2_gpio_switches,
ARRAY_SIZE(h2_gpio_switches));
}
static void __init h2_init(void)
{
h2_nor_resource.end = h2_nor_resource.start = omap_cs3_phys();
h2_nor_resource.end += SZ_32M - 1;
h2_nand_resource.end = h2_nand_resource.start = OMAP_CS2B_PHYS;
h2_nand_resource.end += SZ_4K - 1;
if (gpio_request(H2_NAND_RB_GPIO_PIN, "NAND ready") < 0)
BUG();
gpio_direction_input(H2_NAND_RB_GPIO_PIN);
omap_cfg_reg(L3_1610_FLASH_CS2B_OE);
omap_cfg_reg(M8_1610_FLASH_CS2B_WE);
/* MMC: card detect and WP */
/* omap_cfg_reg(U19_ARMIO1); */ /* CD */
omap_cfg_reg(BALLOUT_V8_ARMIO3); /* WP */
/* Mux pins for keypad */
omap_cfg_reg(F18_1610_KBC0);
omap_cfg_reg(D20_1610_KBC1);
omap_cfg_reg(D19_1610_KBC2);
omap_cfg_reg(E18_1610_KBC3);
omap_cfg_reg(C21_1610_KBC4);
omap_cfg_reg(G18_1610_KBR0);
omap_cfg_reg(F19_1610_KBR1);
omap_cfg_reg(H14_1610_KBR2);
omap_cfg_reg(E20_1610_KBR3);
omap_cfg_reg(E19_1610_KBR4);
omap_cfg_reg(N19_1610_KBR5);
platform_add_devices(h2_devices, ARRAY_SIZE(h2_devices));
omap_board_config = h2_config;
omap_board_config_size = ARRAY_SIZE(h2_config);
omap_serial_init();
omap_register_i2c_bus(1, 100, h2_i2c_board_info,
ARRAY_SIZE(h2_i2c_board_info));
omap1_usb_init(&h2_usb_config);
h2_mmc_init();
}
