C++ (Cpp) h4_init_flash Examples

Example #1

File: board-h4.c Project: bubyte/linwizard-strtrk

static void __init omap_h4_init_irq(void)
{
	omap2_init_common_hw();
	omap_init_irq();
	omap_gpio_init();
	h4_init_flash();
}

Example #2

File: board-h4.c Project: AdiPat/i9003_Kernel

static void __init omap_h4_init_irq(void)
{
	omap_board_config = h4_config;
	omap_board_config_size = ARRAY_SIZE(h4_config);
	omap2_init_common_hw(NULL, NULL);
	omap_init_irq();
	h4_init_flash();
}

Example #3

File: board-h4.c Project: 303750856/linux-3.1

static void __init omap_h4_init(void)
{
	omap2420_mux_init(board_mux, OMAP_PACKAGE_ZAF);

	omap_board_config = h4_config;
	omap_board_config_size = ARRAY_SIZE(h4_config);

	/*
	 * Make sure the serial ports are muxed on at this point.
	 * You have to mux them off in device drivers later on
	 * if not needed.
	 */

#if defined(CONFIG_KEYBOARD_OMAP) || defined(CONFIG_KEYBOARD_OMAP_MODULE)
	omap_mux_init_gpio(88, OMAP_PULL_ENA | OMAP_PULL_UP);
	omap_mux_init_gpio(89, OMAP_PULL_ENA | OMAP_PULL_UP);
	omap_mux_init_gpio(124, OMAP_PULL_ENA | OMAP_PULL_UP);
	omap_mux_init_signal("mcbsp2_dr.gpio_11", OMAP_PULL_ENA | OMAP_PULL_UP);
	if (omap_has_menelaus()) {
		omap_mux_init_signal("sdrc_a14.gpio0",
			OMAP_PULL_ENA | OMAP_PULL_UP);
		omap_mux_init_signal("vlynq_rx0.gpio_15", 0);
		omap_mux_init_signal("gpio_98", 0);
		row_gpios[5] = 0;
		col_gpios[2] = 15;
		col_gpios[6] = 18;
	} else {
		omap_mux_init_signal("gpio_96", OMAP_PULL_ENA | OMAP_PULL_UP);
		omap_mux_init_signal("gpio_100", 0);
		omap_mux_init_signal("gpio_98", 0);
	}
	omap_mux_init_signal("gpio_90", 0);
	omap_mux_init_signal("gpio_91", 0);
	omap_mux_init_signal("gpio_36", 0);
	omap_mux_init_signal("mcbsp2_clkx.gpio_12", 0);
	omap_mux_init_signal("gpio_97", 0);
#endif

	i2c_register_board_info(1, h4_i2c_board_info,
			ARRAY_SIZE(h4_i2c_board_info));

	platform_add_devices(h4_devices, ARRAY_SIZE(h4_devices));
	omap2_usbfs_init(&h4_usb_config);
	omap_serial_init();
	h4_init_flash();
}

Example #4

File: board-h4.c Project: KCFTech/Linux_3_2_0-26_Kernel

static void __init omap_h4_init(void)
{
	omap2420_mux_init(board_mux, OMAP_PACKAGE_ZAF);

	/*
	 * Make sure the serial ports are muxed on at this point.
	 * You have to mux them off in device drivers later on
	 * if not needed.
	 */

	board_mkp_init();
	i2c_register_board_info(1, h4_i2c_board_info,
			ARRAY_SIZE(h4_i2c_board_info));

	platform_add_devices(h4_devices, ARRAY_SIZE(h4_devices));
	omap2_usbfs_init(&h4_usb_config);
	omap_serial_init();
	omap_sdrc_init(NULL, NULL);
	h4_init_flash();

	omap_display_init(&h4_dss_data);
}