static int initr_w83c553f(void)
{
/*
* Initialise the ISA bridge
*/
initialise_w83c553f();
return 0;
}
/*
* This is the next part if the initialization sequence: we are now
* running from RAM and have a "normal" C environment, i. e. global
* data can be written, BSS has been cleared, the stack size in not
* that critical any more, etc.
*/
void board_init_r(gd_t *id, ulong dest_addr)
{
bd_t *bd;
ulong malloc_start;
#ifndef CONFIG_SYS_NO_FLASH
ulong flash_size;
#endif
gd = id; /* initialize RAM version of global data */
bd = gd->bd;
gd->flags |= GD_FLG_RELOC; /* tell others: relocation done */
/* The Malloc area is immediately below the monitor copy in DRAM */
malloc_start = dest_addr - TOTAL_MALLOC_LEN;
#if defined(CONFIG_MPC85xx) || defined(CONFIG_MPC86xx)
/*
* The gd->arch.cpu pointer is set to an address in flash before
* relocation. We need to update it to point to the same CPU entry
* in RAM.
*/
gd->arch.cpu += dest_addr - CONFIG_SYS_MONITOR_BASE;
/*
* If we didn't know the cpu mask & # cores, we can save them of
* now rather than 'computing' them constantly
*/
fixup_cpu();
#endif
#ifdef CONFIG_SYS_EXTRA_ENV_RELOC
/*
* Some systems need to relocate the env_addr pointer early because the
* location it points to will get invalidated before env_relocate is
* called. One example is on systems that might use a L2 or L3 cache
* in SRAM mode and initialize that cache from SRAM mode back to being
* a cache in cpu_init_r.
*/
gd->env_addr += dest_addr - CONFIG_SYS_MONITOR_BASE;
#endif
serial_initialize();
debug("Now running in RAM - U-Boot at: %08lx\n", dest_addr);
WATCHDOG_RESET();
/*
* Setup trap handlers
*/
trap_init(dest_addr);
#ifdef CONFIG_ADDR_MAP
init_addr_map();
#endif
#if defined(CONFIG_BOARD_EARLY_INIT_R)
board_early_init_r();
#endif
monitor_flash_len = (ulong)&__init_end - dest_addr;
WATCHDOG_RESET();
#ifdef CONFIG_LOGBUFFER
logbuff_init_ptrs();
#endif
#ifdef CONFIG_POST
post_output_backlog();
#endif
WATCHDOG_RESET();
#if defined(CONFIG_SYS_DELAYED_ICACHE)
icache_enable(); /* it's time to enable the instruction cache */
#endif
#if defined(CONFIG_SYS_INIT_RAM_LOCK) && defined(CONFIG_E500)
unlock_ram_in_cache(); /* it's time to unlock D-cache in e500 */
#endif
#if defined(CONFIG_PCI) && defined(CONFIG_SYS_EARLY_PCI_INIT)
/*
* Do early PCI configuration _before_ the flash gets initialised,
* because PCU ressources are crucial for flash access on some boards.
*/
pci_init();
#endif
#if defined(CONFIG_WINBOND_83C553)
/*
* Initialise the ISA bridge
*/
initialise_w83c553f();
#endif
asm("sync ; isync");
mem_malloc_init(malloc_start, TOTAL_MALLOC_LEN);
#if !defined(CONFIG_SYS_NO_FLASH)
puts("Flash: ");
if (board_flash_wp_on()) {
printf("Uninitialized - Write Protect On\n");
/* Since WP is on, we can't find real size. Set to 0 */
flash_size = 0;
} else if ((flash_size = flash_init()) > 0) {
#ifdef CONFIG_SYS_FLASH_CHECKSUM
print_size(flash_size, "");
/*
* Compute and print flash CRC if flashchecksum is set to 'y'
*
* NOTE: Maybe we should add some WATCHDOG_RESET()? XXX
*/
if (getenv_yesno("flashchecksum") == 1) {
printf(" CRC: %08X",
crc32(0,
(const unsigned char *)
CONFIG_SYS_FLASH_BASE, flash_size)
);
}
putc('\n');
#else /* !CONFIG_SYS_FLASH_CHECKSUM */
print_size(flash_size, "\n");
#endif /* CONFIG_SYS_FLASH_CHECKSUM */
} else {
puts(failed);
hang();
}
/* update start of FLASH memory */
bd->bi_flashstart = CONFIG_SYS_FLASH_BASE;
/* size of FLASH memory (final value) */
bd->bi_flashsize = flash_size;
#if defined(CONFIG_SYS_UPDATE_FLASH_SIZE)
/* Make a update of the Memctrl. */
update_flash_size(flash_size);
#endif
#if defined(CONFIG_OXC) || defined(CONFIG_RMU)
/* flash mapped at end of memory map */
bd->bi_flashoffset = CONFIG_SYS_TEXT_BASE + flash_size;
#elif CONFIG_SYS_MONITOR_BASE == CONFIG_SYS_FLASH_BASE
bd->bi_flashoffset = monitor_flash_len; /* reserved area for monitor */
#endif
#endif /* !CONFIG_SYS_NO_FLASH */
WATCHDOG_RESET();
/* initialize higher level parts of CPU like time base and timers */
cpu_init_r();
WATCHDOG_RESET();
#ifdef CONFIG_SPI
#if !defined(CONFIG_ENV_IS_IN_EEPROM)
spi_init_f();
#endif
spi_init_r();
#endif
#if defined(CONFIG_CMD_NAND)
WATCHDOG_RESET();
puts("NAND: ");
nand_init(); /* go init the NAND */
#endif
#ifdef CONFIG_GENERIC_MMC
/*
* MMC initialization is called before relocating env.
* Thus It is required that operations like pin multiplexer
* be put in board_init.
*/
WATCHDOG_RESET();
puts("MMC: ");
mmc_initialize(bd);
#endif
/* relocate environment function pointers etc. */
env_relocate();
/*
* after non-volatile devices & environment is setup and cpu code have
* another round to deal with any initialization that might require
* full access to the environment or loading of some image (firmware)
* from a non-volatile device
*/
cpu_secondary_init_r();
/*
* Fill in missing fields of bd_info.
* We do this here, where we have "normal" access to the
* environment; we used to do this still running from ROM,
* where had to use getenv_f(), which can be pretty slow when
* the environment is in EEPROM.
*/
#if defined(CONFIG_SYS_EXTBDINFO)
#if defined(CONFIG_405GP) || defined(CONFIG_405EP)
#if defined(CONFIG_I2CFAST)
/*
* set bi_iic_fast for linux taking environment variable
* "i2cfast" into account
*/
{
if (getenv_yesno("i2cfast") == 1) {
bd->bi_iic_fast[0] = 1;
bd->bi_iic_fast[1] = 1;
}
}
#endif /* CONFIG_I2CFAST */
#endif /* CONFIG_405GP, CONFIG_405EP */
#endif /* CONFIG_SYS_EXTBDINFO */
#if defined(CONFIG_SC3)
sc3_read_eeprom();
#endif
#if defined(CONFIG_ID_EEPROM) || defined(CONFIG_SYS_I2C_MAC_OFFSET)
mac_read_from_eeprom();
#endif
#ifdef CONFIG_CMD_NET
/* kept around for legacy kernels only ... ignore the next section */
eth_getenv_enetaddr("ethaddr", bd->bi_enetaddr);
#ifdef CONFIG_HAS_ETH1
eth_getenv_enetaddr("eth1addr", bd->bi_enet1addr);
#endif
#ifdef CONFIG_HAS_ETH2
eth_getenv_enetaddr("eth2addr", bd->bi_enet2addr);
#endif
#ifdef CONFIG_HAS_ETH3
eth_getenv_enetaddr("eth3addr", bd->bi_enet3addr);
#endif
#ifdef CONFIG_HAS_ETH4
eth_getenv_enetaddr("eth4addr", bd->bi_enet4addr);
#endif
#ifdef CONFIG_HAS_ETH5
eth_getenv_enetaddr("eth5addr", bd->bi_enet5addr);
#endif
#endif /* CONFIG_CMD_NET */
WATCHDOG_RESET();
#if defined(CONFIG_PCI) && !defined(CONFIG_SYS_EARLY_PCI_INIT)
/*
* Do pci configuration
*/
pci_init();
#endif
/** leave this here (after malloc(), environment and PCI are working) **/
/* Initialize stdio devices */
stdio_init();
/* Initialize the jump table for applications */
jumptable_init();
#if defined(CONFIG_API)
/* Initialize API */
api_init();
#endif
/* Initialize the console (after the relocation and devices init) */
console_init_r();
#if defined(CONFIG_MISC_INIT_R)
/* miscellaneous platform dependent initialisations */
misc_init_r();
#endif
#if defined(CONFIG_CMD_KGDB)
WATCHDOG_RESET();
puts("KGDB: ");
kgdb_init();
#endif
debug("U-Boot relocated to %08lx\n", dest_addr);
/*
* Enable Interrupts
*/
interrupt_init();
#if defined(CONFIG_STATUS_LED) && defined(STATUS_LED_BOOT)
status_led_set(STATUS_LED_BOOT, STATUS_LED_BLINKING);
#endif
udelay(20);
/* Initialize from environment */
load_addr = getenv_ulong("loadaddr", 16, load_addr);
WATCHDOG_RESET();
#if defined(CONFIG_CMD_SCSI)
WATCHDOG_RESET();
puts("SCSI: ");
scsi_init();
#endif
#if defined(CONFIG_CMD_DOC)
WATCHDOG_RESET();
puts("DOC: ");
doc_init();
#endif
#ifdef CONFIG_BITBANGMII
bb_miiphy_init();
#endif
#if defined(CONFIG_CMD_NET)
WATCHDOG_RESET();
puts("Net: ");
eth_initialize(bd);
#endif
#if defined(CONFIG_CMD_NET) && defined(CONFIG_RESET_PHY_R)
WATCHDOG_RESET();
debug("Reset Ethernet PHY\n");
reset_phy();
#endif
#ifdef CONFIG_POST
post_run(NULL, POST_RAM | post_bootmode_get(0));
#endif
#if defined(CONFIG_CMD_PCMCIA) \
&& !defined(CONFIG_CMD_IDE)
WATCHDOG_RESET();
puts("PCMCIA:");
pcmcia_init();
#endif
#if defined(CONFIG_CMD_IDE)
WATCHDOG_RESET();
#ifdef CONFIG_IDE_8xx_PCCARD
puts("PCMCIA:");
#else
puts("IDE: ");
#endif
#if defined(CONFIG_START_IDE)
if (board_start_ide())
ide_init();
#else
ide_init();
#endif
#endif
#ifdef CONFIG_LAST_STAGE_INIT
WATCHDOG_RESET();
/*
* Some parts can be only initialized if all others (like
* Interrupts) are up and running (i.e. the PC-style ISA
* keyboard).
*/
last_stage_init();
#endif
#if defined(CONFIG_CMD_BEDBUG)
WATCHDOG_RESET();
bedbug_init();
#endif
#if defined(CONFIG_PRAM) || defined(CONFIG_LOGBUFFER)
/*
* Export available size of memory for Linux,
* taking into account the protected RAM at top of memory
*/
{
ulong pram = 0;
char memsz[32];
#ifdef CONFIG_PRAM
pram = getenv_ulong("pram", 10, CONFIG_PRAM);
#endif
#ifdef CONFIG_LOGBUFFER
#ifndef CONFIG_ALT_LB_ADDR
/* Also take the logbuffer into account (pram is in kB) */
pram += (LOGBUFF_LEN + LOGBUFF_OVERHEAD) / 1024;
#endif
#endif
sprintf(memsz, "%ldk", (ulong) (bd->bi_memsize / 1024) - pram);
setenv("mem", memsz);
}
#endif
#ifdef CONFIG_PS2KBD
puts("PS/2: ");
kbd_init();
#endif
/* Initialization complete - start the monitor */
/* main_loop() can return to retry autoboot, if so just run it again. */
for (;;) {
WATCHDOG_RESET();
main_loop();
}
/* NOTREACHED - no way out of command loop except booting */
}
