/************ PROCEDURES ********************/
void step (unsigned char data, unsigned char motorNumber) {
data = data & 0x0F; // make sure only the LS-nibble will be overwritten
unsigned int lectura;
switch (motorNumber) {
case 1:
lectura = mPORTDRead() & (~(0xF << 4));
mPORTDWrite(lectura | (data << 4));
break;
case 2:
lectura = mPORTCRead() & (~(0xF << 1));
mPORTCWrite(lectura | (data << 1));
break;
case 3:
case 4:
motorNumber -= 3;
lectura = mPORTERead() & (~(0xF << motorNumber*4));
mPORTEWrite(lectura | (data << motorNumber*4));
break;
}
}
//********************************
//********************************
//********** INITIALISE **********
//********************************
//********************************
void initialise (void)
{
BYTE data;
//##### GENERAL NOTE ABOUT PIC32'S #####
//Try and use the peripheral libraries instead of special function registers for everything (literally everything!) to avoid
//bugs that can be caused by the pipeline and interrupts.
//---------------------------------
//----- CONFIGURE PERFORMANCE -----
//---------------------------------
//----- SETUP EVERYTHING FOR OPTIMUM PERFORMANCE -----
SYSTEMConfigPerformance(80000000ul); //Note this sets peripheral bus to '1' max speed (regardless of configuration bit setting)
//Use PBCLK divider of 1:1 to calculate UART baud, timer tick etc
//----- SET PERIPHERAL BUS DIVISOR -----
//To minimize dynamic power the PB divisor should be chosen to run the peripherals at the lowest frequency that provides acceptable system performance
mOSCSetPBDIV(OSC_PB_DIV_2); //OSC_PB_DIV_1, OSC_PB_DIV_2, OSC_PB_DIV_4, OSC_PB_DIV_8,
//----- SETUP INTERRUPTS -----
INTEnableSystemMultiVectoredInt();
//-------------------------
//----- SETUP IO PINS -----
//-------------------------
//(Device will powerup with all IO pins as inputs)
//----- TURN OFF THE JTAG PORT -----
//(JTAG is on by default)
//mJTAGPortEnable(0); //Must be on for Microchip Multimedia Development board
#define PORTA_IO 0xc2ff //Setup the IO pin type (0 = output, 1 = input)
mPORTAWrite(0xc033); //Set initial ouput pin states
mPORTASetPinsDigitalIn(PORTA_IO); //(Sets high bits as input)
mPORTASetPinsDigitalOut(~PORTA_IO); //(Sets high bits as output)
#define PORTB_IO 0xfbff //Setup the IO pin type (0 = output, 1 = input)
mPORTBWrite(0x6d13); //Set initial ouput pin states
mPORTBSetPinsDigitalIn(PORTB_IO); //(Sets high bits as input)
mPORTBSetPinsDigitalOut(~PORTB_IO); //(Sets high bits as output)
mPORTBSetPinsDigitalIn(BIT_0 | BIT_1 | BIT_3 | BIT_4 | BIT_15); //Joystick inputs
#define PORTC_IO 0xf01e //Setup the IO pin type (0 = output, 1 = input)
mPORTCWrite(0x3018); //Set initial ouput pin states
mPORTCSetPinsDigitalIn(PORTC_IO); //(Sets high bits as input)
mPORTCSetPinsDigitalOut(~PORTC_IO); //(Sets high bits as output)
#define PORTD_IO 0x7bfe //Setup the IO pin type (0 = output, 1 = input)
mPORTDWrite(0xbdaf); //Set initial ouput pin states
mPORTDSetPinsDigitalIn(PORTD_IO); //(Sets high bits as input)
mPORTDSetPinsDigitalOut(~PORTD_IO); //(Sets high bits as output)
mPORTDSetPinsDigitalOut(BIT_2 | BIT_1); //LED's 2 and 3
mPORTDSetPinsDigitalIn(BIT_9);
#define PORTE_IO 0x03ff //Setup the IO pin type (0 = output, 1 = input)
mPORTEWrite(0x02a2); //Set initial ouput pin states
mPORTESetPinsDigitalIn(PORTE_IO); //(Sets high bits as input)
mPORTESetPinsDigitalOut(~PORTE_IO); //(Sets high bits as output)
#define PORTF_IO 0x111f //Setup the IO pin type (0 = output, 1 = input)
mPORTFWrite(0x0039); //Set initial ouput pin states
mPORTFSetPinsDigitalIn(PORTF_IO); //(Sets high bits as input)
mPORTFSetPinsDigitalOut(~PORTF_IO); //(Sets high bits as output)
#define PORTG_IO 0xd3cf //Setup the IO pin type (0 = output, 1 = input)
mPORTGWrite(0xf203); //Set initial ouput pin states
mPORTGSetPinsDigitalIn(PORTG_IO); //(Sets high bits as input)
mPORTGSetPinsDigitalOut(~PORTG_IO); //(Sets high bits as output)
//Read pins using:
// mPORTAReadBits(BIT_0);
//Write pins using:
// mPORTAClearBits(BIT_0);
// mPORTASetBits(BIT_0);
// mPORTAToggleBits(BIT_0);
//----- INPUT CHANGE NOTIFICATION CONFIGURATION -----
//EnableCN0();
ConfigCNPullups(CN2_PULLUP_ENABLE | CN3_PULLUP_ENABLE | CN5_PULLUP_ENABLE | CN6_PULLUP_ENABLE | CN12_PULLUP_ENABLE); //Joystick pins
//----- SETUP THE A TO D PINS -----
ENABLE_ALL_DIG;
//---------------------
//----- SETUP USB -----
//---------------------
//The USB specifications require that USB peripheral devices must never source current onto the Vbus pin. Additionally, USB peripherals should not source
//current on D+ or D- when the host/hub is not actively powering the Vbus line. When designing a self powered (as opposed to bus powered) USB peripheral
//device, the firmware should make sure not to turn on the USB module and D+ or D- pull up resistor unless Vbus is actively powered. Therefore, the
//firmware needs some means to detect when Vbus is being powered by the host. A 5V tolerant I/O pin can be connected to Vbus (through a resistor), and
//can be used to detect when Vbus is high (host actively powering), or low (host is shut down or otherwise not supplying power). The USB firmware
//can then periodically poll this I/O pin to know when it is okay to turn on the USB module/D+/D- pull up resistor. When designing a purely bus powered
//peripheral device, it is not possible to source current on D+ or D- when the host is not actively providing power on Vbus. Therefore, implementing this
//bus sense feature is optional. This firmware can be made to use this bus sense feature by making sure "USE_USB_BUS_SENSE_IO" has been defined in the
//HardwareProfile.h file.
// #if defined(USE_USB_BUS_SENSE_IO)
// tris_usb_bus_sense = INPUT_PIN; // See HardwareProfile.h
// #endif
//If the host PC sends a GetStatus (device) request, the firmware must respond and let the host know if the USB peripheral device is currently bus powered
//or self powered. See chapter 9 in the official USB specifications for details regarding this request. If the peripheral device is capable of being both
//self and bus powered, it should not return a hard coded value for this request. Instead, firmware should check if it is currently self or bus powered, and
//respond accordingly. If the hardware has been configured like demonstrated on the PICDEM FS USB Demo Board, an I/O pin can be polled to determine the
//currently selected power source. On the PICDEM FS USB Demo Board, "RA2" is used for this purpose. If using this feature, make sure "USE_SELF_POWER_SENSE_IO"
//has been defined in HardwareProfile.h, and that an appropriate I/O pin has been mapped to it in HardwareProfile.h.
// #if defined(USE_SELF_POWER_SENSE_IO)
// tris_self_power = INPUT_PIN; // See HardwareProfile.h
// #endif
//Enable the USB port now - we will check to see if Vbus is powered at the end of init and disable it if not.
//USBDeviceInit(); //usb_device.c. Initializes USB module SFRs and firmware variables to known states.
//------------------------
//----- SETUP TIMERS -----
//------------------------
//(INCLUDE THE USAGE OF ALL TIMERS HERE EVEN IF NOT SETUP HERE SO THIS IS THE ONE POINT OF
//REFERENCE TO KNOW WHICH TIMERS ARE IN USE AND FOR WHAT).
//----- SETUP TIMER 1 -----
//Used for: Available
//OpenTimer1((T1_ON | T1_IDLE_CON | T1_GATE_OFF | T1_PS_1_4 | T1_SOURCE_INT), 20000);
//----- SETUP TIMER 2 -----
//Used for:
//OpenTimer2((T2_ON | T2_IDLE_CON | T2_GATE_OFF | T2_PS_1_1 | T2_SOURCE_INT), 0xffff); //0xffff = 305Hz
//----- SETUP TIMER 3 -----
//Used for:
//OpenTimer3((T3_ON | T3_IDLE_CON | T3_GATE_OFF | T3_PS_1_1 | T3_SOURCE_INT), PIEZO_TIMER_PERIOD);
//----- SETUP TIMER 4 -----
//Used for:
//OpenTimer4((T4_ON | T4_IDLE_CON | T4_GATE_OFF | T4_PS_1_1 | T4_SOURCE_INT), 20000);
//----- SETUP TIMER 5 -----
//Used for: Heartbeat
OpenTimer5((T5_ON | T5_IDLE_CON | T5_GATE_OFF | T5_PS_1_1 | T5_SOURCE_INT), 40000); //1mS with 80MHz osc and PB_DIV_2
ConfigIntTimer5(T5_INT_ON | T5_INT_PRIOR_7); //1=lowest priority to 7=highest priority. ISR function must specify same value
//---------------------------------
//----- SETUP EVAL BOARD CPLD -----
//---------------------------------
//Graphics bus width = 16
mPORTGSetPinsDigitalOut(BIT_14);
mPORTGSetBits(BIT_14);
//SPI source select = SPI3 (not used)
mPORTGSetPinsDigitalOut(BIT_12);
mPORTGClearBits(BIT_12);
//SPI peripheral destination select = Expansion Slot (not used)
mPORTASetPinsDigitalOut(BIT_7 | BIT_6);
mPORTASetBits(BIT_7);
mPORTAClearBits(BIT_6);
//--------------------------------------
//----- PARALLEL MASTER PORT SETUP -----
//--------------------------------------
PMMODE = 0;
PMAEN = 0;
PMCON = 0;
PMMODE = 0x0610;
PMCONbits.PTRDEN = 1; //Enable RD line
PMCONbits.PTWREN = 1; //Enable WR line
PMCONbits.PMPEN = 1; //Enable PMP
//------------------------------
//----- INITIALISE DISPLAY -----
//------------------------------
display_initialise();
display_test();
//LOAD OUR GLOBAL HTML STYLES FILE READY FOR DISPLAY HTML PAGES
BYTE dummy_styles_count;
DWORD file_size;
if (display_html_setup_read_file(global_css, 0, &file_size))
{
dummy_styles_count = 0;
display_html_read_styles(&file_size, &dummy_styles_count, 1); //1 = this is global styles file
}
}
