void GCS_MAVLINK_Rover::handleMessage(mavlink_message_t* msg)
{
switch (msg->msgid) {
case MAVLINK_MSG_ID_RC_CHANNELS_OVERRIDE:
{
// allow override of RC channel values for HIL
// or for complete GCS control of switch position
// and RC PWM values.
if (msg->sysid != rover.g.sysid_my_gcs) { // Only accept control from our gcs
break;
}
uint32_t tnow = AP_HAL::millis();
mavlink_rc_channels_override_t packet;
mavlink_msg_rc_channels_override_decode(msg, &packet);
RC_Channels::set_override(0, packet.chan1_raw, tnow);
RC_Channels::set_override(1, packet.chan2_raw, tnow);
RC_Channels::set_override(2, packet.chan3_raw, tnow);
RC_Channels::set_override(3, packet.chan4_raw, tnow);
RC_Channels::set_override(4, packet.chan5_raw, tnow);
RC_Channels::set_override(5, packet.chan6_raw, tnow);
RC_Channels::set_override(6, packet.chan7_raw, tnow);
RC_Channels::set_override(7, packet.chan8_raw, tnow);
break;
}
case MAVLINK_MSG_ID_MANUAL_CONTROL:
{
if (msg->sysid != rover.g.sysid_my_gcs) { // Only accept control from our gcs
break;
}
mavlink_manual_control_t packet;
mavlink_msg_manual_control_decode(msg, &packet);
if (packet.target != rover.g.sysid_this_mav) {
break; // only accept control aimed at us
}
uint32_t tnow = AP_HAL::millis();
const int16_t roll = (packet.y == INT16_MAX) ? 0 : rover.channel_steer->get_radio_min() + (rover.channel_steer->get_radio_max() - rover.channel_steer->get_radio_min()) * (packet.y + 1000) / 2000.0f;
const int16_t throttle = (packet.z == INT16_MAX) ? 0 : rover.channel_throttle->get_radio_min() + (rover.channel_throttle->get_radio_max() - rover.channel_throttle->get_radio_min()) * (packet.z + 1000) / 2000.0f;
RC_Channels::set_override(uint8_t(rover.rcmap.roll() - 1), roll, tnow);
RC_Channels::set_override(uint8_t(rover.rcmap.throttle() - 1), throttle, tnow);
break;
}
case MAVLINK_MSG_ID_HEARTBEAT:
{
// We keep track of the last time we received a heartbeat from our GCS for failsafe purposes
if (msg->sysid != rover.g.sysid_my_gcs) {
break;
}
rover.last_heartbeat_ms = AP_HAL::millis();
rover.failsafe_trigger(FAILSAFE_EVENT_GCS, false);
break;
}
case MAVLINK_MSG_ID_SET_ATTITUDE_TARGET: // MAV ID: 82
{
// decode packet
mavlink_set_attitude_target_t packet;
mavlink_msg_set_attitude_target_decode(msg, &packet);
// exit if vehicle is not in Guided mode
if (rover.control_mode != &rover.mode_guided) {
break;
}
// ensure type_mask specifies to use thrust
if ((packet.type_mask & MAVLINK_SET_ATT_TYPE_MASK_THROTTLE_IGNORE) != 0) {
break;
}
// convert thrust to ground speed
packet.thrust = constrain_float(packet.thrust, -1.0f, 1.0f);
const float target_speed = rover.control_mode->get_speed_default() * packet.thrust;
// if the body_yaw_rate field is ignored, convert quaternion to heading
if ((packet.type_mask & MAVLINK_SET_ATT_TYPE_MASK_YAW_RATE_IGNORE) != 0) {
// convert quaternion to heading
float target_heading_cd = degrees(Quaternion(packet.q[0], packet.q[1], packet.q[2], packet.q[3]).get_euler_yaw()) * 100.0f;
rover.mode_guided.set_desired_heading_and_speed(target_heading_cd, target_speed);
} else {
// use body_yaw_rate field
rover.mode_guided.set_desired_turn_rate_and_speed((RAD_TO_DEG * packet.body_yaw_rate) * 100.0f, target_speed);
}
break;
}
case MAVLINK_MSG_ID_SET_POSITION_TARGET_LOCAL_NED: // MAV ID: 84
{
// decode packet
mavlink_set_position_target_local_ned_t packet;
mavlink_msg_set_position_target_local_ned_decode(msg, &packet);
// exit if vehicle is not in Guided mode
if (rover.control_mode != &rover.mode_guided) {
break;
}
// check for supported coordinate frames
if (packet.coordinate_frame != MAV_FRAME_LOCAL_NED &&
packet.coordinate_frame != MAV_FRAME_LOCAL_OFFSET_NED &&
packet.coordinate_frame != MAV_FRAME_BODY_NED &&
packet.coordinate_frame != MAV_FRAME_BODY_OFFSET_NED) {
break;
}
bool pos_ignore = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_POS_IGNORE;
bool vel_ignore = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_VEL_IGNORE;
bool acc_ignore = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_ACC_IGNORE;
bool yaw_ignore = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_YAW_IGNORE;
bool yaw_rate_ignore = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_YAW_RATE_IGNORE;
// prepare target position
Location target_loc = rover.current_loc;
if (!pos_ignore) {
switch (packet.coordinate_frame) {
case MAV_FRAME_BODY_NED:
case MAV_FRAME_BODY_OFFSET_NED: {
// rotate from body-frame to NE frame
const float ne_x = packet.x * rover.ahrs.cos_yaw() - packet.y * rover.ahrs.sin_yaw();
const float ne_y = packet.x * rover.ahrs.sin_yaw() + packet.y * rover.ahrs.cos_yaw();
// add offset to current location
location_offset(target_loc, ne_x, ne_y);
}
break;
case MAV_FRAME_LOCAL_OFFSET_NED:
// add offset to current location
location_offset(target_loc, packet.x, packet.y);
break;
default:
// MAV_FRAME_LOCAL_NED interpret as an offset from home
target_loc = rover.ahrs.get_home();
location_offset(target_loc, packet.x, packet.y);
break;
}
}
float target_speed = 0.0f;
float target_yaw_cd = 0.0f;
// consume velocity and convert to target speed and heading
if (!vel_ignore) {
const float speed_max = rover.control_mode->get_speed_default();
// convert vector length into a speed
target_speed = constrain_float(safe_sqrt(sq(packet.vx) + sq(packet.vy)), -speed_max, speed_max);
// convert vector direction to target yaw
target_yaw_cd = degrees(atan2f(packet.vy, packet.vx)) * 100.0f;
// rotate target yaw if provided in body-frame
if (packet.coordinate_frame == MAV_FRAME_BODY_NED || packet.coordinate_frame == MAV_FRAME_BODY_OFFSET_NED) {
target_yaw_cd = wrap_180_cd(target_yaw_cd + rover.ahrs.yaw_sensor);
}
}
// consume yaw heading
if (!yaw_ignore) {
target_yaw_cd = ToDeg(packet.yaw) * 100.0f;
// rotate target yaw if provided in body-frame
if (packet.coordinate_frame == MAV_FRAME_BODY_NED || packet.coordinate_frame == MAV_FRAME_BODY_OFFSET_NED) {
target_yaw_cd = wrap_180_cd(target_yaw_cd + rover.ahrs.yaw_sensor);
}
}
// consume yaw rate
float target_turn_rate_cds = 0.0f;
if (!yaw_rate_ignore) {
target_turn_rate_cds = ToDeg(packet.yaw_rate) * 100.0f;
}
// handling case when both velocity and either yaw or yaw-rate are provided
// by default, we consider that the rover will drive forward
float speed_dir = 1.0f;
if (!vel_ignore && (!yaw_ignore || !yaw_rate_ignore)) {
// Note: we are using the x-axis velocity to determine direction even though
// the frame may have been provided in MAV_FRAME_LOCAL_OFFSET_NED or MAV_FRAME_LOCAL_NED
if (is_negative(packet.vx)) {
speed_dir = -1.0f;
}
}
// set guided mode targets
if (!pos_ignore) {
// consume position target
rover.mode_guided.set_desired_location(target_loc);
} else if (pos_ignore && !vel_ignore && acc_ignore && yaw_ignore && yaw_rate_ignore) {
// consume velocity
rover.mode_guided.set_desired_heading_and_speed(target_yaw_cd, speed_dir * target_speed);
} else if (pos_ignore && !vel_ignore && acc_ignore && yaw_ignore && !yaw_rate_ignore) {
// consume velocity and turn rate
rover.mode_guided.set_desired_turn_rate_and_speed(target_turn_rate_cds, speed_dir * target_speed);
} else if (pos_ignore && !vel_ignore && acc_ignore && !yaw_ignore && yaw_rate_ignore) {
// consume velocity
rover.mode_guided.set_desired_heading_and_speed(target_yaw_cd, speed_dir * target_speed);
} else if (pos_ignore && vel_ignore && acc_ignore && !yaw_ignore && yaw_rate_ignore) {
// consume just target heading (probably only skid steering vehicles can do this)
rover.mode_guided.set_desired_heading_and_speed(target_yaw_cd, 0.0f);
} else if (pos_ignore && vel_ignore && acc_ignore && yaw_ignore && !yaw_rate_ignore) {
// consume just turn rate(probably only skid steering vehicles can do this)
rover.mode_guided.set_desired_turn_rate_and_speed(target_turn_rate_cds, 0.0f);
}
break;
}
case MAVLINK_MSG_ID_SET_POSITION_TARGET_GLOBAL_INT: // MAV ID: 86
{
// decode packet
mavlink_set_position_target_global_int_t packet;
mavlink_msg_set_position_target_global_int_decode(msg, &packet);
// exit if vehicle is not in Guided mode
if (rover.control_mode != &rover.mode_guided) {
break;
}
// check for supported coordinate frames
if (packet.coordinate_frame != MAV_FRAME_GLOBAL &&
packet.coordinate_frame != MAV_FRAME_GLOBAL_INT &&
packet.coordinate_frame != MAV_FRAME_GLOBAL_RELATIVE_ALT &&
packet.coordinate_frame != MAV_FRAME_GLOBAL_RELATIVE_ALT_INT &&
packet.coordinate_frame != MAV_FRAME_GLOBAL_TERRAIN_ALT &&
packet.coordinate_frame != MAV_FRAME_GLOBAL_TERRAIN_ALT_INT) {
break;
}
bool pos_ignore = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_POS_IGNORE;
bool vel_ignore = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_VEL_IGNORE;
bool acc_ignore = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_ACC_IGNORE;
bool yaw_ignore = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_YAW_IGNORE;
bool yaw_rate_ignore = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_YAW_RATE_IGNORE;
// prepare target position
Location target_loc = rover.current_loc;
if (!pos_ignore) {
// sanity check location
if (!check_latlng(packet.lat_int, packet.lon_int)) {
// result = MAV_RESULT_FAILED;
break;
}
target_loc.lat = packet.lat_int;
target_loc.lng = packet.lon_int;
}
float target_speed = 0.0f;
float target_yaw_cd = 0.0f;
// consume velocity and convert to target speed and heading
if (!vel_ignore) {
const float speed_max = rover.control_mode->get_speed_default();
// convert vector length into a speed
target_speed = constrain_float(safe_sqrt(sq(packet.vx) + sq(packet.vy)), -speed_max, speed_max);
// convert vector direction to target yaw
target_yaw_cd = degrees(atan2f(packet.vy, packet.vx)) * 100.0f;
// rotate target yaw if provided in body-frame
if (packet.coordinate_frame == MAV_FRAME_BODY_NED || packet.coordinate_frame == MAV_FRAME_BODY_OFFSET_NED) {
target_yaw_cd = wrap_180_cd(target_yaw_cd + rover.ahrs.yaw_sensor);
}
}
// consume yaw heading
if (!yaw_ignore) {
target_yaw_cd = ToDeg(packet.yaw) * 100.0f;
// rotate target yaw if provided in body-frame
if (packet.coordinate_frame == MAV_FRAME_BODY_NED || packet.coordinate_frame == MAV_FRAME_BODY_OFFSET_NED) {
target_yaw_cd = wrap_180_cd(target_yaw_cd + rover.ahrs.yaw_sensor);
}
}
// consume yaw rate
float target_turn_rate_cds = 0.0f;
if (!yaw_rate_ignore) {
target_turn_rate_cds = ToDeg(packet.yaw_rate) * 100.0f;
}
// handling case when both velocity and either yaw or yaw-rate are provided
// by default, we consider that the rover will drive forward
float speed_dir = 1.0f;
if (!vel_ignore && (!yaw_ignore || !yaw_rate_ignore)) {
// Note: we are using the x-axis velocity to determine direction even though
// the frame is provided in MAV_FRAME_GLOBAL_xxx
if (is_negative(packet.vx)) {
speed_dir = -1.0f;
}
}
// set guided mode targets
if (!pos_ignore) {
// consume position target
rover.mode_guided.set_desired_location(target_loc);
} else if (pos_ignore && !vel_ignore && acc_ignore && yaw_ignore && yaw_rate_ignore) {
// consume velocity
rover.mode_guided.set_desired_heading_and_speed(target_yaw_cd, speed_dir * target_speed);
} else if (pos_ignore && !vel_ignore && acc_ignore && yaw_ignore && !yaw_rate_ignore) {
// consume velocity and turn rate
rover.mode_guided.set_desired_turn_rate_and_speed(target_turn_rate_cds, speed_dir * target_speed);
} else if (pos_ignore && !vel_ignore && acc_ignore && !yaw_ignore && yaw_rate_ignore) {
// consume velocity
rover.mode_guided.set_desired_heading_and_speed(target_yaw_cd, speed_dir * target_speed);
} else if (pos_ignore && vel_ignore && acc_ignore && !yaw_ignore && yaw_rate_ignore) {
// consume just target heading (probably only skid steering vehicles can do this)
rover.mode_guided.set_desired_heading_and_speed(target_yaw_cd, 0.0f);
} else if (pos_ignore && vel_ignore && acc_ignore && yaw_ignore && !yaw_rate_ignore) {
// consume just turn rate(probably only skid steering vehicles can do this)
rover.mode_guided.set_desired_turn_rate_and_speed(target_turn_rate_cds, 0.0f);
}
break;
}
#if HIL_MODE != HIL_MODE_DISABLED
case MAVLINK_MSG_ID_HIL_STATE:
{
mavlink_hil_state_t packet;
mavlink_msg_hil_state_decode(msg, &packet);
// sanity check location
if (!check_latlng(packet.lat, packet.lon)) {
break;
}
// set gps hil sensor
Location loc;
loc.lat = packet.lat;
loc.lng = packet.lon;
loc.alt = packet.alt/10;
Vector3f vel(packet.vx, packet.vy, packet.vz);
vel *= 0.01f;
gps.setHIL(0, AP_GPS::GPS_OK_FIX_3D,
packet.time_usec/1000,
loc, vel, 10, 0);
// rad/sec
Vector3f gyros;
gyros.x = packet.rollspeed;
gyros.y = packet.pitchspeed;
gyros.z = packet.yawspeed;
// m/s/s
Vector3f accels;
accels.x = packet.xacc * (GRAVITY_MSS/1000.0f);
accels.y = packet.yacc * (GRAVITY_MSS/1000.0f);
accels.z = packet.zacc * (GRAVITY_MSS/1000.0f);
ins.set_gyro(0, gyros);
ins.set_accel(0, accels);
compass.setHIL(0, packet.roll, packet.pitch, packet.yaw);
compass.setHIL(1, packet.roll, packet.pitch, packet.yaw);
break;
}
#endif // HIL_MODE
#if MOUNT == ENABLED
// deprecated. Use MAV_CMD_DO_MOUNT_CONFIGURE
case MAVLINK_MSG_ID_MOUNT_CONFIGURE:
{
rover.camera_mount.configure_msg(msg);
break;
}
// deprecated. Use MAV_CMD_DO_MOUNT_CONTROL
case MAVLINK_MSG_ID_MOUNT_CONTROL:
{
rover.camera_mount.control_msg(msg);
break;
}
#endif // MOUNT == ENABLED
case MAVLINK_MSG_ID_RADIO:
case MAVLINK_MSG_ID_RADIO_STATUS:
{
handle_radio_status(msg, rover.DataFlash, rover.should_log(MASK_LOG_PM));
break;
}
// send or receive fence points with GCS
case MAVLINK_MSG_ID_FENCE_POINT: // MAV ID: 160
case MAVLINK_MSG_ID_FENCE_FETCH_POINT:
rover.g2.fence.handle_msg(*this, msg);
break;
case MAVLINK_MSG_ID_DISTANCE_SENSOR:
rover.rangefinder.handle_msg(msg);
rover.g2.proximity.handle_msg(msg);
break;
default:
handle_common_message(msg);
break;
} // end switch
} // end handle mavlink
void GCS_MAVLINK_Plane::handleMessage(mavlink_message_t* msg)
{
switch (msg->msgid) {
#if GEOFENCE_ENABLED == ENABLED
// receive a fence point from GCS and store in EEPROM
case MAVLINK_MSG_ID_FENCE_POINT: {
mavlink_fence_point_t packet;
mavlink_msg_fence_point_decode(msg, &packet);
if (plane.g.fence_action != FENCE_ACTION_NONE) {
send_text(MAV_SEVERITY_WARNING,"Fencing must be disabled");
} else if (packet.count != plane.g.fence_total) {
send_text(MAV_SEVERITY_WARNING,"Bad fence point");
} else if (!check_latlng(packet.lat,packet.lng)) {
send_text(MAV_SEVERITY_WARNING,"Invalid fence point, lat or lng too large");
} else {
plane.set_fence_point_with_index(Vector2l(packet.lat*1.0e7f, packet.lng*1.0e7f), packet.idx);
}
break;
}
// send a fence point to GCS
case MAVLINK_MSG_ID_FENCE_FETCH_POINT: {
mavlink_fence_fetch_point_t packet;
mavlink_msg_fence_fetch_point_decode(msg, &packet);
if (packet.idx >= plane.g.fence_total) {
send_text(MAV_SEVERITY_WARNING,"Bad fence point");
} else {
Vector2l point = plane.get_fence_point_with_index(packet.idx);
mavlink_msg_fence_point_send_buf(msg, chan, msg->sysid, msg->compid, packet.idx, plane.g.fence_total,
point.x*1.0e-7f, point.y*1.0e-7f);
}
break;
}
#endif // GEOFENCE_ENABLED
case MAVLINK_MSG_ID_MANUAL_CONTROL:
{
if (msg->sysid != plane.g.sysid_my_gcs) {
break; // only accept control from our gcs
}
mavlink_manual_control_t packet;
mavlink_msg_manual_control_decode(msg, &packet);
if (packet.target != plane.g.sysid_this_mav) {
break; // only accept messages aimed at us
}
uint32_t tnow = AP_HAL::millis();
manual_override(plane.channel_roll, packet.y, 1000, 2000, tnow);
manual_override(plane.channel_pitch, packet.x, 1000, 2000, tnow, true);
manual_override(plane.channel_throttle, packet.z, 0, 1000, tnow);
manual_override(plane.channel_rudder, packet.r, 1000, 2000, tnow);
// a manual control message is considered to be a 'heartbeat' from the ground station for failsafe purposes
plane.failsafe.last_heartbeat_ms = tnow;
break;
}
case MAVLINK_MSG_ID_HEARTBEAT:
{
// We keep track of the last time we received a heartbeat from
// our GCS for failsafe purposes
if (msg->sysid != plane.g.sysid_my_gcs) break;
plane.failsafe.last_heartbeat_ms = AP_HAL::millis();
break;
}
case MAVLINK_MSG_ID_HIL_STATE:
{
#if HIL_SUPPORT
if (plane.g.hil_mode != 1) {
break;
}
mavlink_hil_state_t packet;
mavlink_msg_hil_state_decode(msg, &packet);
// sanity check location
if (!check_latlng(packet.lat, packet.lon)) {
break;
}
last_hil_state = packet;
// set gps hil sensor
const Location loc{packet.lat, packet.lon, packet.alt/10, Location::AltFrame::ABSOLUTE};
Vector3f vel(packet.vx, packet.vy, packet.vz);
vel *= 0.01f;
// setup airspeed pressure based on 3D speed, no wind
plane.airspeed.setHIL(sq(vel.length()) / 2.0f + 2013);
plane.gps.setHIL(0, AP_GPS::GPS_OK_FIX_3D,
packet.time_usec/1000,
loc, vel, 10, 0);
// rad/sec
Vector3f gyros;
gyros.x = packet.rollspeed;
gyros.y = packet.pitchspeed;
gyros.z = packet.yawspeed;
// m/s/s
Vector3f accels;
accels.x = packet.xacc * GRAVITY_MSS*0.001f;
accels.y = packet.yacc * GRAVITY_MSS*0.001f;
accels.z = packet.zacc * GRAVITY_MSS*0.001f;
plane.ins.set_gyro(0, gyros);
plane.ins.set_accel(0, accels);
plane.barometer.setHIL(packet.alt*0.001f);
plane.compass.setHIL(0, packet.roll, packet.pitch, packet.yaw);
plane.compass.setHIL(1, packet.roll, packet.pitch, packet.yaw);
// cope with DCM getting badly off due to HIL lag
if (plane.g.hil_err_limit > 0 &&
(fabsf(packet.roll - plane.ahrs.roll) > ToRad(plane.g.hil_err_limit) ||
fabsf(packet.pitch - plane.ahrs.pitch) > ToRad(plane.g.hil_err_limit) ||
wrap_PI(fabsf(packet.yaw - plane.ahrs.yaw)) > ToRad(plane.g.hil_err_limit))) {
plane.ahrs.reset_attitude(packet.roll, packet.pitch, packet.yaw);
}
#endif
break;
}
case MAVLINK_MSG_ID_RADIO:
case MAVLINK_MSG_ID_RADIO_STATUS:
{
handle_radio_status(msg, plane.should_log(MASK_LOG_PM));
break;
}
case MAVLINK_MSG_ID_DISTANCE_SENSOR:
plane.rangefinder.handle_msg(msg);
break;
case MAVLINK_MSG_ID_TERRAIN_DATA:
case MAVLINK_MSG_ID_TERRAIN_CHECK:
#if AP_TERRAIN_AVAILABLE
plane.terrain.handle_data(chan, msg);
#endif
break;
case MAVLINK_MSG_ID_SET_ATTITUDE_TARGET:
{
// Only allow companion computer (or other external controller) to
// control attitude in GUIDED mode. We DON'T want external control
// in e.g., RTL, CICLE. Specifying a single mode for companion
// computer control is more safe (even more so when using
// FENCE_ACTION = 4 for geofence failures).
if ((plane.control_mode != &plane.mode_guided) &&
(plane.control_mode != &plane.mode_avoidADSB)) { // don't screw up failsafes
break;
}
mavlink_set_attitude_target_t att_target;
mavlink_msg_set_attitude_target_decode(msg, &att_target);
// Mappings: If any of these bits are set, the corresponding input should be ignored.
// NOTE, when parsing the bits we invert them for easier interpretation but transport has them inverted
// bit 1: body roll rate
// bit 2: body pitch rate
// bit 3: body yaw rate
// bit 4: unknown
// bit 5: unknown
// bit 6: reserved
// bit 7: throttle
// bit 8: attitude
// if not setting all Quaternion values, use _rate flags to indicate which fields.
// Extract the Euler roll angle from the Quaternion.
Quaternion q(att_target.q[0], att_target.q[1],
att_target.q[2], att_target.q[3]);
// NOTE: att_target.type_mask is inverted for easier interpretation
att_target.type_mask = att_target.type_mask ^ 0xFF;
uint8_t attitude_mask = att_target.type_mask & 0b10000111; // q plus rpy
uint32_t now = AP_HAL::millis();
if ((attitude_mask & 0b10000001) || // partial, including roll
(attitude_mask == 0b10000000)) { // all angles
plane.guided_state.forced_rpy_cd.x = degrees(q.get_euler_roll()) * 100.0f;
// Update timer for external roll to the nav control
plane.guided_state.last_forced_rpy_ms.x = now;
}
if ((attitude_mask & 0b10000010) || // partial, including pitch
(attitude_mask == 0b10000000)) { // all angles
plane.guided_state.forced_rpy_cd.y = degrees(q.get_euler_pitch()) * 100.0f;
// Update timer for external pitch to the nav control
plane.guided_state.last_forced_rpy_ms.y = now;
}
if ((attitude_mask & 0b10000100) || // partial, including yaw
(attitude_mask == 0b10000000)) { // all angles
plane.guided_state.forced_rpy_cd.z = degrees(q.get_euler_yaw()) * 100.0f;
// Update timer for external yaw to the nav control
plane.guided_state.last_forced_rpy_ms.z = now;
}
if (att_target.type_mask & 0b01000000) { // throttle
plane.guided_state.forced_throttle = att_target.thrust * 100.0f;
// Update timer for external throttle
plane.guided_state.last_forced_throttle_ms = now;
}
break;
}
case MAVLINK_MSG_ID_SET_HOME_POSITION:
{
mavlink_set_home_position_t packet;
mavlink_msg_set_home_position_decode(msg, &packet);
Location new_home_loc {};
new_home_loc.lat = packet.latitude;
new_home_loc.lng = packet.longitude;
new_home_loc.alt = packet.altitude / 10;
if (!set_home(new_home_loc, false)) {
// silently fails...
break;
}
break;
}
case MAVLINK_MSG_ID_SET_POSITION_TARGET_LOCAL_NED:
{
// decode packet
mavlink_set_position_target_local_ned_t packet;
mavlink_msg_set_position_target_local_ned_decode(msg, &packet);
// exit if vehicle is not in Guided mode
if (plane.control_mode != &plane.mode_guided) {
break;
}
// only local moves for now
if (packet.coordinate_frame != MAV_FRAME_LOCAL_OFFSET_NED) {
break;
}
// just do altitude for now
plane.next_WP_loc.alt += -packet.z*100.0;
gcs().send_text(MAV_SEVERITY_INFO, "Change alt to %.1f",
(double)((plane.next_WP_loc.alt - plane.home.alt)*0.01));
break;
}
case MAVLINK_MSG_ID_SET_POSITION_TARGET_GLOBAL_INT:
{
// Only want to allow companion computer position control when
// in a certain mode to avoid inadvertently sending these
// kinds of commands when the autopilot is responding to problems
// in modes such as RTL, CIRCLE, etc. Specifying ONLY one mode
// for companion computer control is more safe (provided
// one uses the FENCE_ACTION = 4 (RTL) for geofence failures).
if (plane.control_mode != &plane.mode_guided && plane.control_mode != &plane.mode_avoidADSB) {
//don't screw up failsafes
break;
}
mavlink_set_position_target_global_int_t pos_target;
mavlink_msg_set_position_target_global_int_decode(msg, &pos_target);
// Unexpectedly, the mask is expecting "ones" for dimensions that should
// be IGNORNED rather than INCLUDED. See mavlink documentation of the
// SET_POSITION_TARGET_GLOBAL_INT message, type_mask field.
const uint16_t alt_mask = 0b1111111111111011; // (z mask at bit 3)
bool msg_valid = true;
AP_Mission::Mission_Command cmd = {0};
if (pos_target.type_mask & alt_mask)
{
cmd.content.location.alt = pos_target.alt * 100;
cmd.content.location.relative_alt = false;
cmd.content.location.terrain_alt = false;
switch (pos_target.coordinate_frame)
{
case MAV_FRAME_GLOBAL_INT:
break; //default to MSL altitude
case MAV_FRAME_GLOBAL_RELATIVE_ALT_INT:
cmd.content.location.relative_alt = true;
break;
case MAV_FRAME_GLOBAL_TERRAIN_ALT_INT:
cmd.content.location.relative_alt = true;
cmd.content.location.terrain_alt = true;
break;
default:
gcs().send_text(MAV_SEVERITY_WARNING, "Invalid coord frame in SET_POSTION_TARGET_GLOBAL_INT");
msg_valid = false;
break;
}
if (msg_valid) {
handle_change_alt_request(cmd);
}
} // end if alt_mask
break;
}
case MAVLINK_MSG_ID_ADSB_VEHICLE:
case MAVLINK_MSG_ID_UAVIONIX_ADSB_OUT_CFG:
case MAVLINK_MSG_ID_UAVIONIX_ADSB_OUT_DYNAMIC:
case MAVLINK_MSG_ID_UAVIONIX_ADSB_TRANSCEIVER_HEALTH_REPORT:
plane.adsb.handle_message(chan, msg);
break;
default:
handle_common_message(msg);
break;
} // end switch
} // end handle mavlink
void GCS_MAVLINK_Copter::handleMessage(mavlink_message_t* msg)
{
switch (msg->msgid) {
case MAVLINK_MSG_ID_HEARTBEAT: // MAV ID: 0
{
// We keep track of the last time we received a heartbeat from our GCS for failsafe purposes
if(msg->sysid != copter.g.sysid_my_gcs) break;
copter.failsafe.last_heartbeat_ms = AP_HAL::millis();
break;
}
case MAVLINK_MSG_ID_MANUAL_CONTROL:
{
if (msg->sysid != copter.g.sysid_my_gcs) {
break; // only accept control from our gcs
}
mavlink_manual_control_t packet;
mavlink_msg_manual_control_decode(msg, &packet);
if (packet.target != copter.g.sysid_this_mav) {
break; // only accept control aimed at us
}
if (packet.z < 0) { // Copter doesn't do negative thrust
break;
}
uint32_t tnow = AP_HAL::millis();
manual_override(copter.channel_roll, packet.y, 1000, 2000, tnow);
manual_override(copter.channel_pitch, packet.x, 1000, 2000, tnow, true);
manual_override(copter.channel_throttle, packet.z, 0, 1000, tnow);
manual_override(copter.channel_yaw, packet.r, 1000, 2000, tnow);
// a manual control message is considered to be a 'heartbeat' from the ground station for failsafe purposes
copter.failsafe.last_heartbeat_ms = tnow;
break;
}
#if MODE_GUIDED_ENABLED == ENABLED
case MAVLINK_MSG_ID_SET_ATTITUDE_TARGET: // MAV ID: 82
{
// decode packet
mavlink_set_attitude_target_t packet;
mavlink_msg_set_attitude_target_decode(msg, &packet);
// exit if vehicle is not in Guided mode or Auto-Guided mode
if (!copter.flightmode->in_guided_mode()) {
break;
}
// ensure type_mask specifies to use attitude and thrust
if ((packet.type_mask & ((1<<7)|(1<<6))) != 0) {
break;
}
// convert thrust to climb rate
packet.thrust = constrain_float(packet.thrust, 0.0f, 1.0f);
float climb_rate_cms = 0.0f;
if (is_equal(packet.thrust, 0.5f)) {
climb_rate_cms = 0.0f;
} else if (packet.thrust > 0.5f) {
// climb at up to WPNAV_SPEED_UP
climb_rate_cms = (packet.thrust - 0.5f) * 2.0f * copter.wp_nav->get_default_speed_up();
} else {
// descend at up to WPNAV_SPEED_DN
climb_rate_cms = (0.5f - packet.thrust) * 2.0f * -fabsf(copter.wp_nav->get_default_speed_down());
}
// if the body_yaw_rate field is ignored, use the commanded yaw position
// otherwise use the commanded yaw rate
bool use_yaw_rate = false;
if ((packet.type_mask & (1<<2)) == 0) {
use_yaw_rate = true;
}
copter.mode_guided.set_angle(Quaternion(packet.q[0],packet.q[1],packet.q[2],packet.q[3]),
climb_rate_cms, use_yaw_rate, packet.body_yaw_rate);
break;
}
case MAVLINK_MSG_ID_SET_POSITION_TARGET_LOCAL_NED: // MAV ID: 84
{
// decode packet
mavlink_set_position_target_local_ned_t packet;
mavlink_msg_set_position_target_local_ned_decode(msg, &packet);
// exit if vehicle is not in Guided mode or Auto-Guided mode
if (!copter.flightmode->in_guided_mode()) {
break;
}
// check for supported coordinate frames
if (packet.coordinate_frame != MAV_FRAME_LOCAL_NED &&
packet.coordinate_frame != MAV_FRAME_LOCAL_OFFSET_NED &&
packet.coordinate_frame != MAV_FRAME_BODY_NED &&
packet.coordinate_frame != MAV_FRAME_BODY_OFFSET_NED) {
break;
}
bool pos_ignore = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_POS_IGNORE;
bool vel_ignore = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_VEL_IGNORE;
bool acc_ignore = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_ACC_IGNORE;
bool yaw_ignore = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_YAW_IGNORE;
bool yaw_rate_ignore = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_YAW_RATE_IGNORE;
/*
* for future use:
* bool force = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_FORCE;
*/
// prepare position
Vector3f pos_vector;
if (!pos_ignore) {
// convert to cm
pos_vector = Vector3f(packet.x * 100.0f, packet.y * 100.0f, -packet.z * 100.0f);
// rotate to body-frame if necessary
if (packet.coordinate_frame == MAV_FRAME_BODY_NED ||
packet.coordinate_frame == MAV_FRAME_BODY_OFFSET_NED) {
copter.rotate_body_frame_to_NE(pos_vector.x, pos_vector.y);
}
// add body offset if necessary
if (packet.coordinate_frame == MAV_FRAME_LOCAL_OFFSET_NED ||
packet.coordinate_frame == MAV_FRAME_BODY_NED ||
packet.coordinate_frame == MAV_FRAME_BODY_OFFSET_NED) {
pos_vector += copter.inertial_nav.get_position();
} else {
// convert from alt-above-home to alt-above-ekf-origin
if (!AP::ahrs().home_is_set()) {
break;
}
const Location &origin = copter.inertial_nav.get_origin();
pos_vector.z += AP::ahrs().get_home().alt;
pos_vector.z -= origin.alt;
}
}
// prepare velocity
Vector3f vel_vector;
if (!vel_ignore) {
// convert to cm
vel_vector = Vector3f(packet.vx * 100.0f, packet.vy * 100.0f, -packet.vz * 100.0f);
// rotate to body-frame if necessary
if (packet.coordinate_frame == MAV_FRAME_BODY_NED || packet.coordinate_frame == MAV_FRAME_BODY_OFFSET_NED) {
copter.rotate_body_frame_to_NE(vel_vector.x, vel_vector.y);
}
}
// prepare yaw
float yaw_cd = 0.0f;
bool yaw_relative = false;
float yaw_rate_cds = 0.0f;
if (!yaw_ignore) {
yaw_cd = ToDeg(packet.yaw) * 100.0f;
yaw_relative = packet.coordinate_frame == MAV_FRAME_BODY_NED || packet.coordinate_frame == MAV_FRAME_BODY_OFFSET_NED;
}
if (!yaw_rate_ignore) {
yaw_rate_cds = ToDeg(packet.yaw_rate) * 100.0f;
}
// send request
if (!pos_ignore && !vel_ignore && acc_ignore) {
copter.mode_guided.set_destination_posvel(pos_vector, vel_vector, !yaw_ignore, yaw_cd, !yaw_rate_ignore, yaw_rate_cds, yaw_relative);
} else if (pos_ignore && !vel_ignore && acc_ignore) {
copter.mode_guided.set_velocity(vel_vector, !yaw_ignore, yaw_cd, !yaw_rate_ignore, yaw_rate_cds, yaw_relative);
} else if (!pos_ignore && vel_ignore && acc_ignore) {
copter.mode_guided.set_destination(pos_vector, !yaw_ignore, yaw_cd, !yaw_rate_ignore, yaw_rate_cds, yaw_relative);
}
break;
}
case MAVLINK_MSG_ID_SET_POSITION_TARGET_GLOBAL_INT: // MAV ID: 86
{
// decode packet
mavlink_set_position_target_global_int_t packet;
mavlink_msg_set_position_target_global_int_decode(msg, &packet);
// exit if vehicle is not in Guided mode or Auto-Guided mode
if (!copter.flightmode->in_guided_mode()) {
break;
}
bool pos_ignore = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_POS_IGNORE;
bool vel_ignore = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_VEL_IGNORE;
bool acc_ignore = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_ACC_IGNORE;
bool yaw_ignore = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_YAW_IGNORE;
bool yaw_rate_ignore = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_YAW_RATE_IGNORE;
/*
* for future use:
* bool force = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_FORCE;
*/
Vector3f pos_neu_cm; // position (North, East, Up coordinates) in centimeters
if(!pos_ignore) {
// sanity check location
if (!check_latlng(packet.lat_int, packet.lon_int)) {
break;
}
Location::AltFrame frame;
if (!mavlink_coordinate_frame_to_location_alt_frame(packet.coordinate_frame, frame)) {
// unknown coordinate frame
break;
}
const Location loc{
packet.lat_int,
packet.lon_int,
int32_t(packet.alt*100),
frame,
};
if (!loc.get_vector_from_origin_NEU(pos_neu_cm)) {
break;
}
}
// prepare yaw
float yaw_cd = 0.0f;
bool yaw_relative = false;
float yaw_rate_cds = 0.0f;
if (!yaw_ignore) {
yaw_cd = ToDeg(packet.yaw) * 100.0f;
yaw_relative = packet.coordinate_frame == MAV_FRAME_BODY_NED || packet.coordinate_frame == MAV_FRAME_BODY_OFFSET_NED;
}
if (!yaw_rate_ignore) {
yaw_rate_cds = ToDeg(packet.yaw_rate) * 100.0f;
}
if (!pos_ignore && !vel_ignore && acc_ignore) {
copter.mode_guided.set_destination_posvel(pos_neu_cm, Vector3f(packet.vx * 100.0f, packet.vy * 100.0f, -packet.vz * 100.0f), !yaw_ignore, yaw_cd, !yaw_rate_ignore, yaw_rate_cds, yaw_relative);
} else if (pos_ignore && !vel_ignore && acc_ignore) {
copter.mode_guided.set_velocity(Vector3f(packet.vx * 100.0f, packet.vy * 100.0f, -packet.vz * 100.0f), !yaw_ignore, yaw_cd, !yaw_rate_ignore, yaw_rate_cds, yaw_relative);
} else if (!pos_ignore && vel_ignore && acc_ignore) {
copter.mode_guided.set_destination(pos_neu_cm, !yaw_ignore, yaw_cd, !yaw_rate_ignore, yaw_rate_cds, yaw_relative);
}
break;
}
#endif
case MAVLINK_MSG_ID_DISTANCE_SENSOR:
{
copter.rangefinder.handle_msg(msg);
#if PROXIMITY_ENABLED == ENABLED
copter.g2.proximity.handle_msg(msg);
#endif
break;
}
case MAVLINK_MSG_ID_OBSTACLE_DISTANCE:
{
#if PROXIMITY_ENABLED == ENABLED
copter.g2.proximity.handle_msg(msg);
#endif
break;
}
#if HIL_MODE != HIL_MODE_DISABLED
case MAVLINK_MSG_ID_HIL_STATE: // MAV ID: 90
{
mavlink_hil_state_t packet;
mavlink_msg_hil_state_decode(msg, &packet);
// sanity check location
if (!check_latlng(packet.lat, packet.lon)) {
break;
}
// set gps hil sensor
Location loc;
loc.lat = packet.lat;
loc.lng = packet.lon;
loc.alt = packet.alt/10;
Vector3f vel(packet.vx, packet.vy, packet.vz);
vel *= 0.01f;
gps.setHIL(0, AP_GPS::GPS_OK_FIX_3D,
packet.time_usec/1000,
loc, vel, 10, 0);
// rad/sec
Vector3f gyros;
gyros.x = packet.rollspeed;
gyros.y = packet.pitchspeed;
gyros.z = packet.yawspeed;
// m/s/s
Vector3f accels;
accels.x = packet.xacc * (GRAVITY_MSS/1000.0f);
accels.y = packet.yacc * (GRAVITY_MSS/1000.0f);
accels.z = packet.zacc * (GRAVITY_MSS/1000.0f);
ins.set_gyro(0, gyros);
ins.set_accel(0, accels);
AP::baro().setHIL(packet.alt*0.001f);
copter.compass.setHIL(0, packet.roll, packet.pitch, packet.yaw);
copter.compass.setHIL(1, packet.roll, packet.pitch, packet.yaw);
break;
}
#endif // HIL_MODE != HIL_MODE_DISABLED
case MAVLINK_MSG_ID_RADIO:
case MAVLINK_MSG_ID_RADIO_STATUS: // MAV ID: 109
{
handle_radio_status(msg, copter.should_log(MASK_LOG_PM));
break;
}
#if PRECISION_LANDING == ENABLED
case MAVLINK_MSG_ID_LANDING_TARGET:
copter.precland.handle_msg(msg);
break;
#endif
case MAVLINK_MSG_ID_TERRAIN_DATA:
case MAVLINK_MSG_ID_TERRAIN_CHECK:
#if AP_TERRAIN_AVAILABLE && AC_TERRAIN
copter.terrain.handle_data(chan, msg);
#endif
break;
case MAVLINK_MSG_ID_SET_HOME_POSITION:
{
mavlink_set_home_position_t packet;
mavlink_msg_set_home_position_decode(msg, &packet);
if((packet.latitude == 0) && (packet.longitude == 0) && (packet.altitude == 0)) {
if (!copter.set_home_to_current_location(true)) {
// silently ignored
}
} else {
Location new_home_loc;
new_home_loc.lat = packet.latitude;
new_home_loc.lng = packet.longitude;
new_home_loc.alt = packet.altitude / 10;
if (!copter.set_home(new_home_loc, true)) {
// silently ignored
}
}
break;
}
case MAVLINK_MSG_ID_ADSB_VEHICLE:
case MAVLINK_MSG_ID_UAVIONIX_ADSB_OUT_CFG:
case MAVLINK_MSG_ID_UAVIONIX_ADSB_OUT_DYNAMIC:
case MAVLINK_MSG_ID_UAVIONIX_ADSB_TRANSCEIVER_HEALTH_REPORT:
#if ADSB_ENABLED == ENABLED
copter.adsb.handle_message(chan, msg);
#endif
break;
#if TOY_MODE_ENABLED == ENABLED
case MAVLINK_MSG_ID_NAMED_VALUE_INT:
copter.g2.toy_mode.handle_message(msg);
break;
#endif
default:
handle_common_message(msg);
break;
} // end switch
} // end handle mavlink
void GCS_MAVLINK_Rover::handleMessage(mavlink_message_t* msg)
{
switch (msg->msgid) {
case MAVLINK_MSG_ID_REQUEST_DATA_STREAM:
{
handle_request_data_stream(msg, true);
break;
}
case MAVLINK_MSG_ID_COMMAND_INT: {
// decode packet
mavlink_command_int_t packet;
mavlink_msg_command_int_decode(msg, &packet);
MAV_RESULT result = MAV_RESULT_UNSUPPORTED;
switch (packet.command) {
case MAV_CMD_DO_SET_HOME: {
// assume failure
result = MAV_RESULT_FAILED;
if (is_equal(packet.param1, 1.0f)) {
// if param1 is 1, use current location
if (rover.set_home_to_current_location(true)) {
result = MAV_RESULT_ACCEPTED;
}
break;
}
// ensure param1 is zero
if (!is_zero(packet.param1)) {
break;
}
// check frame type is supported
if (packet.frame != MAV_FRAME_GLOBAL &&
packet.frame != MAV_FRAME_GLOBAL_INT &&
packet.frame != MAV_FRAME_GLOBAL_RELATIVE_ALT &&
packet.frame != MAV_FRAME_GLOBAL_RELATIVE_ALT_INT) {
break;
}
// sanity check location
if (!check_latlng(packet.x, packet.y)) {
break;
}
Location new_home_loc {};
new_home_loc.lat = packet.x;
new_home_loc.lng = packet.y;
new_home_loc.alt = packet.z * 100;
// handle relative altitude
if (packet.frame == MAV_FRAME_GLOBAL_RELATIVE_ALT || packet.frame == MAV_FRAME_GLOBAL_RELATIVE_ALT_INT) {
if (!rover.ahrs.home_is_set()) {
// cannot use relative altitude if home is not set
break;
}
new_home_loc.alt += rover.ahrs.get_home().alt;
}
if (rover.set_home(new_home_loc, true)) {
result = MAV_RESULT_ACCEPTED;
}
break;
}
#if MOUNT == ENABLED
case MAV_CMD_DO_SET_ROI: {
// param1 : /* Region of interest mode (not used)*/
// param2 : /* MISSION index/ target ID (not used)*/
// param3 : /* ROI index (not used)*/
// param4 : /* empty */
// x : lat
// y : lon
// z : alt
// sanity check location
if (!check_latlng(packet.x, packet.y)) {
break;
}
Location roi_loc;
roi_loc.lat = packet.x;
roi_loc.lng = packet.y;
roi_loc.alt = (int32_t)(packet.z * 100.0f);
if (roi_loc.lat == 0 && roi_loc.lng == 0 && roi_loc.alt == 0) {
// switch off the camera tracking if enabled
if (rover.camera_mount.get_mode() == MAV_MOUNT_MODE_GPS_POINT) {
rover.camera_mount.set_mode_to_default();
}
} else {
// send the command to the camera mount
rover.camera_mount.set_roi_target(roi_loc);
}
result = MAV_RESULT_ACCEPTED;
break;
}
#endif
default:
result = MAV_RESULT_UNSUPPORTED;
break;
}
// send ACK or NAK
mavlink_msg_command_ack_send_buf(msg, chan, packet.command, result);
break;
}
case MAVLINK_MSG_ID_COMMAND_LONG:
{
// decode
mavlink_command_long_t packet;
mavlink_msg_command_long_decode(msg, &packet);
MAV_RESULT result = MAV_RESULT_UNSUPPORTED;
// do command
switch (packet.command) {
case MAV_CMD_NAV_RETURN_TO_LAUNCH:
rover.set_mode(rover.mode_rtl, MODE_REASON_GCS_COMMAND);
result = MAV_RESULT_ACCEPTED;
break;
#if MOUNT == ENABLED
// Sets the region of interest (ROI) for the camera
case MAV_CMD_DO_SET_ROI:
// sanity check location
if (!check_latlng(packet.param5, packet.param6)) {
break;
}
Location roi_loc;
roi_loc.lat = (int32_t)(packet.param5 * 1.0e7f);
roi_loc.lng = (int32_t)(packet.param6 * 1.0e7f);
roi_loc.alt = (int32_t)(packet.param7 * 100.0f);
if (roi_loc.lat == 0 && roi_loc.lng == 0 && roi_loc.alt == 0) {
// switch off the camera tracking if enabled
if (rover.camera_mount.get_mode() == MAV_MOUNT_MODE_GPS_POINT) {
rover.camera_mount.set_mode_to_default();
}
} else {
// send the command to the camera mount
rover.camera_mount.set_roi_target(roi_loc);
}
result = MAV_RESULT_ACCEPTED;
break;
#endif
case MAV_CMD_DO_MOUNT_CONTROL:
#if MOUNT == ENABLED
rover.camera_mount.control(packet.param1, packet.param2, packet.param3, (MAV_MOUNT_MODE) packet.param7);
result = MAV_RESULT_ACCEPTED;
#endif
break;
case MAV_CMD_MISSION_START:
rover.set_mode(rover.mode_auto, MODE_REASON_GCS_COMMAND);
result = MAV_RESULT_ACCEPTED;
break;
case MAV_CMD_PREFLIGHT_REBOOT_SHUTDOWN:
if (is_equal(packet.param1, 1.0f) || is_equal(packet.param1, 3.0f)) {
// when packet.param1 == 3 we reboot to hold in bootloader
hal.scheduler->reboot(is_equal(packet.param1, 3.0f));
result = MAV_RESULT_ACCEPTED;
}
break;
case MAV_CMD_COMPONENT_ARM_DISARM:
if (is_equal(packet.param1, 1.0f)) {
// run pre_arm_checks and arm_checks and display failures
if (rover.arm_motors(AP_Arming::MAVLINK)) {
result = MAV_RESULT_ACCEPTED;
} else {
result = MAV_RESULT_FAILED;
}
} else if (is_zero(packet.param1)) {
if (rover.disarm_motors()) {
result = MAV_RESULT_ACCEPTED;
} else {
result = MAV_RESULT_FAILED;
}
} else {
result = MAV_RESULT_UNSUPPORTED;
}
break;
case MAV_CMD_DO_FENCE_ENABLE:
result = MAV_RESULT_ACCEPTED;
switch ((uint16_t)packet.param1) {
case 0:
rover.g2.fence.enable(false);
break;
case 1:
rover.g2.fence.enable(true);
break;
default:
result = MAV_RESULT_FAILED;
break;
}
break;
case MAV_CMD_DO_SET_HOME:
{
// param1 : use current (1=use current location, 0=use specified location)
// param5 : latitude
// param6 : longitude
// param7 : altitude
result = MAV_RESULT_FAILED; // assume failure
if (is_equal(packet.param1, 1.0f)) {
if (rover.set_home_to_current_location(true)) {
result = MAV_RESULT_ACCEPTED;
}
} else {
// ensure param1 is zero
if (!is_zero(packet.param1)) {
break;
}
Location new_home_loc {};
new_home_loc.lat = static_cast<int32_t>(packet.param5 * 1.0e7f);
new_home_loc.lng = static_cast<int32_t>(packet.param6 * 1.0e7f);
new_home_loc.alt = static_cast<int32_t>(packet.param7 * 100.0f);
if (rover.set_home(new_home_loc, true)) {
result = MAV_RESULT_ACCEPTED;
}
}
break;
}
case MAV_CMD_NAV_SET_YAW_SPEED:
{
// param1 : yaw angle to adjust direction by in centidegress
// param2 : Speed - normalized to 0 .. 1
// exit if vehicle is not in Guided mode
if (rover.control_mode != &rover.mode_guided) {
break;
}
// send yaw change and target speed to guided mode controller
const float speed_max = rover.control_mode->get_speed_default();
const float target_speed = constrain_float(packet.param2 * speed_max, -speed_max, speed_max);
rover.mode_guided.set_desired_heading_delta_and_speed(packet.param1, target_speed);
result = MAV_RESULT_ACCEPTED;
break;
}
case MAV_CMD_ACCELCAL_VEHICLE_POS:
result = MAV_RESULT_FAILED;
if (rover.ins.get_acal()->gcs_vehicle_position(packet.param1)) {
result = MAV_RESULT_ACCEPTED;
}
break;
case MAV_CMD_DO_MOTOR_TEST:
// param1 : motor sequence number (a number from 1 to max number of motors on the vehicle)
// param2 : throttle type (0=throttle percentage, 1=PWM, 2=pilot throttle channel pass-through. See MOTOR_TEST_THROTTLE_TYPE enum)
// param3 : throttle (range depends upon param2)
// param4 : timeout (in seconds)
result = rover.mavlink_motor_test_start(chan, static_cast<uint8_t>(packet.param1),
static_cast<uint8_t>(packet.param2),
static_cast<int16_t>(packet.param3),
packet.param4);
break;
default:
result = handle_command_long_message(packet);
break;
}
mavlink_msg_command_ack_send_buf(
msg,
chan,
packet.command,
result);
break;
}
case MAVLINK_MSG_ID_RC_CHANNELS_OVERRIDE:
{
// allow override of RC channel values for HIL
// or for complete GCS control of switch position
// and RC PWM values.
if (msg->sysid != rover.g.sysid_my_gcs) { // Only accept control from our gcs
break;
}
mavlink_rc_channels_override_t packet;
mavlink_msg_rc_channels_override_decode(msg, &packet);
RC_Channels::set_override(0, packet.chan1_raw);
RC_Channels::set_override(1, packet.chan2_raw);
RC_Channels::set_override(2, packet.chan3_raw);
RC_Channels::set_override(3, packet.chan4_raw);
RC_Channels::set_override(4, packet.chan5_raw);
RC_Channels::set_override(5, packet.chan6_raw);
RC_Channels::set_override(6, packet.chan7_raw);
RC_Channels::set_override(7, packet.chan8_raw);
rover.failsafe.rc_override_timer = AP_HAL::millis();
rover.failsafe_trigger(FAILSAFE_EVENT_RC, false);
break;
}
case MAVLINK_MSG_ID_MANUAL_CONTROL:
{
if (msg->sysid != rover.g.sysid_my_gcs) { // Only accept control from our gcs
break;
}
mavlink_manual_control_t packet;
mavlink_msg_manual_control_decode(msg, &packet);
if (packet.target != rover.g.sysid_this_mav) {
break; // only accept control aimed at us
}
const int16_t roll = (packet.y == INT16_MAX) ? 0 : rover.channel_steer->get_radio_min() + (rover.channel_steer->get_radio_max() - rover.channel_steer->get_radio_min()) * (packet.y + 1000) / 2000.0f;
const int16_t throttle = (packet.z == INT16_MAX) ? 0 : rover.channel_throttle->get_radio_min() + (rover.channel_throttle->get_radio_max() - rover.channel_throttle->get_radio_min()) * (packet.z + 1000) / 2000.0f;
RC_Channels::set_override(uint8_t(rover.rcmap.roll() - 1), roll);
RC_Channels::set_override(uint8_t(rover.rcmap.throttle() - 1), throttle);
rover.failsafe.rc_override_timer = AP_HAL::millis();
rover.failsafe_trigger(FAILSAFE_EVENT_RC, false);
break;
}
case MAVLINK_MSG_ID_HEARTBEAT:
{
// We keep track of the last time we received a heartbeat from our GCS for failsafe purposes
if (msg->sysid != rover.g.sysid_my_gcs) {
break;
}
rover.last_heartbeat_ms = rover.failsafe.rc_override_timer = AP_HAL::millis();
rover.failsafe_trigger(FAILSAFE_EVENT_GCS, false);
break;
}
case MAVLINK_MSG_ID_SET_ATTITUDE_TARGET: // MAV ID: 82
{
// decode packet
mavlink_set_attitude_target_t packet;
mavlink_msg_set_attitude_target_decode(msg, &packet);
// exit if vehicle is not in Guided mode
if (rover.control_mode != &rover.mode_guided) {
break;
}
// ensure type_mask specifies to use thrust
if ((packet.type_mask & MAVLINK_SET_ATT_TYPE_MASK_THROTTLE_IGNORE) != 0) {
break;
}
// convert thrust to ground speed
packet.thrust = constrain_float(packet.thrust, -1.0f, 1.0f);
const float target_speed = rover.control_mode->get_speed_default() * packet.thrust;
// if the body_yaw_rate field is ignored, convert quaternion to heading
if ((packet.type_mask & MAVLINK_SET_ATT_TYPE_MASK_YAW_RATE_IGNORE) != 0) {
// convert quaternion to heading
float target_heading_cd = degrees(Quaternion(packet.q[0], packet.q[1], packet.q[2], packet.q[3]).get_euler_yaw()) * 100.0f;
rover.mode_guided.set_desired_heading_and_speed(target_heading_cd, target_speed);
} else {
// use body_yaw_rate field
rover.mode_guided.set_desired_turn_rate_and_speed((RAD_TO_DEG * packet.body_yaw_rate) * 100.0f, target_speed);
}
break;
}
case MAVLINK_MSG_ID_SET_POSITION_TARGET_LOCAL_NED: // MAV ID: 84
{
// decode packet
mavlink_set_position_target_local_ned_t packet;
mavlink_msg_set_position_target_local_ned_decode(msg, &packet);
// exit if vehicle is not in Guided mode
if (rover.control_mode != &rover.mode_guided) {
break;
}
// check for supported coordinate frames
if (packet.coordinate_frame != MAV_FRAME_LOCAL_NED &&
packet.coordinate_frame != MAV_FRAME_LOCAL_OFFSET_NED &&
packet.coordinate_frame != MAV_FRAME_BODY_NED &&
packet.coordinate_frame != MAV_FRAME_BODY_OFFSET_NED) {
break;
}
bool pos_ignore = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_POS_IGNORE;
bool vel_ignore = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_VEL_IGNORE;
bool acc_ignore = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_ACC_IGNORE;
bool yaw_ignore = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_YAW_IGNORE;
bool yaw_rate_ignore = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_YAW_RATE_IGNORE;
// prepare target position
Location target_loc = rover.current_loc;
if (!pos_ignore) {
switch (packet.coordinate_frame) {
case MAV_FRAME_BODY_NED:
case MAV_FRAME_BODY_OFFSET_NED: {
// rotate from body-frame to NE frame
const float ne_x = packet.x * rover.ahrs.cos_yaw() - packet.y * rover.ahrs.sin_yaw();
const float ne_y = packet.x * rover.ahrs.sin_yaw() + packet.y * rover.ahrs.cos_yaw();
// add offset to current location
location_offset(target_loc, ne_x, ne_y);
}
break;
case MAV_FRAME_LOCAL_OFFSET_NED:
// add offset to current location
location_offset(target_loc, packet.x, packet.y);
break;
default:
// MAV_FRAME_LOCAL_NED interpret as an offset from home
target_loc = rover.ahrs.get_home();
location_offset(target_loc, packet.x, packet.y);
break;
}
}
float target_speed = 0.0f;
float target_yaw_cd = 0.0f;
// consume velocity and convert to target speed and heading
if (!vel_ignore) {
const float speed_max = rover.control_mode->get_speed_default();
// convert vector length into a speed
target_speed = constrain_float(safe_sqrt(sq(packet.vx) + sq(packet.vy)), -speed_max, speed_max);
// convert vector direction to target yaw
target_yaw_cd = degrees(atan2f(packet.vy, packet.vx)) * 100.0f;
// rotate target yaw if provided in body-frame
if (packet.coordinate_frame == MAV_FRAME_BODY_NED || packet.coordinate_frame == MAV_FRAME_BODY_OFFSET_NED) {
target_yaw_cd = wrap_180_cd(target_yaw_cd + rover.ahrs.yaw_sensor);
}
}
// consume yaw heading
if (!yaw_ignore) {
target_yaw_cd = ToDeg(packet.yaw) * 100.0f;
// rotate target yaw if provided in body-frame
if (packet.coordinate_frame == MAV_FRAME_BODY_NED || packet.coordinate_frame == MAV_FRAME_BODY_OFFSET_NED) {
target_yaw_cd = wrap_180_cd(target_yaw_cd + rover.ahrs.yaw_sensor);
}
}
// consume yaw rate
float target_turn_rate_cds = 0.0f;
if (!yaw_rate_ignore) {
target_turn_rate_cds = ToDeg(packet.yaw_rate) * 100.0f;
}
// handling case when both velocity and either yaw or yaw-rate are provided
// by default, we consider that the rover will drive forward
float speed_dir = 1.0f;
if (!vel_ignore && (!yaw_ignore || !yaw_rate_ignore)) {
// Note: we are using the x-axis velocity to determine direction even though
// the frame may have been provided in MAV_FRAME_LOCAL_OFFSET_NED or MAV_FRAME_LOCAL_NED
if (is_negative(packet.vx)) {
speed_dir = -1.0f;
}
}
// set guided mode targets
if (!pos_ignore && vel_ignore && acc_ignore && yaw_ignore && yaw_rate_ignore) {
// consume position target
rover.mode_guided.set_desired_location(target_loc);
} else if (pos_ignore && !vel_ignore && acc_ignore && yaw_ignore && yaw_rate_ignore) {
// consume velocity
rover.mode_guided.set_desired_heading_and_speed(target_yaw_cd, speed_dir * target_speed);
} else if (pos_ignore && !vel_ignore && acc_ignore && yaw_ignore && !yaw_rate_ignore) {
// consume velocity and turn rate
rover.mode_guided.set_desired_turn_rate_and_speed(target_turn_rate_cds, speed_dir * target_speed);
} else if (pos_ignore && !vel_ignore && acc_ignore && !yaw_ignore && yaw_rate_ignore) {
// consume velocity
rover.mode_guided.set_desired_heading_and_speed(target_yaw_cd, speed_dir * target_speed);
} else if (pos_ignore && vel_ignore && acc_ignore && !yaw_ignore && yaw_rate_ignore) {
// consume just target heading (probably only skid steering vehicles can do this)
rover.mode_guided.set_desired_heading_and_speed(target_yaw_cd, 0.0f);
} else if (pos_ignore && vel_ignore && acc_ignore && yaw_ignore && !yaw_rate_ignore) {
// consume just turn rate(probably only skid steering vehicles can do this)
rover.mode_guided.set_desired_turn_rate_and_speed(target_turn_rate_cds, 0.0f);
}
break;
}
case MAVLINK_MSG_ID_SET_POSITION_TARGET_GLOBAL_INT: // MAV ID: 86
{
// decode packet
mavlink_set_position_target_global_int_t packet;
mavlink_msg_set_position_target_global_int_decode(msg, &packet);
// exit if vehicle is not in Guided mode
if (rover.control_mode != &rover.mode_guided) {
break;
}
// check for supported coordinate frames
if (packet.coordinate_frame != MAV_FRAME_GLOBAL &&
packet.coordinate_frame != MAV_FRAME_GLOBAL_INT &&
packet.coordinate_frame != MAV_FRAME_GLOBAL_RELATIVE_ALT &&
packet.coordinate_frame != MAV_FRAME_GLOBAL_RELATIVE_ALT_INT &&
packet.coordinate_frame != MAV_FRAME_GLOBAL_TERRAIN_ALT &&
packet.coordinate_frame != MAV_FRAME_GLOBAL_TERRAIN_ALT_INT) {
break;
}
bool pos_ignore = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_POS_IGNORE;
bool vel_ignore = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_VEL_IGNORE;
bool acc_ignore = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_ACC_IGNORE;
bool yaw_ignore = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_YAW_IGNORE;
bool yaw_rate_ignore = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_YAW_RATE_IGNORE;
// prepare target position
Location target_loc = rover.current_loc;
if (!pos_ignore) {
// sanity check location
if (!check_latlng(packet.lat_int, packet.lon_int)) {
// result = MAV_RESULT_FAILED;
break;
}
target_loc.lat = packet.lat_int;
target_loc.lng = packet.lon_int;
}
float target_speed = 0.0f;
float target_yaw_cd = 0.0f;
// consume velocity and convert to target speed and heading
if (!vel_ignore) {
const float speed_max = rover.control_mode->get_speed_default();
// convert vector length into a speed
target_speed = constrain_float(safe_sqrt(sq(packet.vx) + sq(packet.vy)), -speed_max, speed_max);
// convert vector direction to target yaw
target_yaw_cd = degrees(atan2f(packet.vy, packet.vx)) * 100.0f;
// rotate target yaw if provided in body-frame
if (packet.coordinate_frame == MAV_FRAME_BODY_NED || packet.coordinate_frame == MAV_FRAME_BODY_OFFSET_NED) {
target_yaw_cd = wrap_180_cd(target_yaw_cd + rover.ahrs.yaw_sensor);
}
}
// consume yaw heading
if (!yaw_ignore) {
target_yaw_cd = ToDeg(packet.yaw) * 100.0f;
// rotate target yaw if provided in body-frame
if (packet.coordinate_frame == MAV_FRAME_BODY_NED || packet.coordinate_frame == MAV_FRAME_BODY_OFFSET_NED) {
target_yaw_cd = wrap_180_cd(target_yaw_cd + rover.ahrs.yaw_sensor);
}
}
// consume yaw rate
float target_turn_rate_cds = 0.0f;
if (!yaw_rate_ignore) {
target_turn_rate_cds = ToDeg(packet.yaw_rate) * 100.0f;
}
// handling case when both velocity and either yaw or yaw-rate are provided
// by default, we consider that the rover will drive forward
float speed_dir = 1.0f;
if (!vel_ignore && (!yaw_ignore || !yaw_rate_ignore)) {
// Note: we are using the x-axis velocity to determine direction even though
// the frame is provided in MAV_FRAME_GLOBAL_xxx
if (is_negative(packet.vx)) {
speed_dir = -1.0f;
}
}
// set guided mode targets
if (!pos_ignore && vel_ignore && acc_ignore && yaw_ignore && yaw_rate_ignore) {
// consume position target
rover.mode_guided.set_desired_location(target_loc);
} else if (pos_ignore && !vel_ignore && acc_ignore && yaw_ignore && yaw_rate_ignore) {
// consume velocity
rover.mode_guided.set_desired_heading_and_speed(target_yaw_cd, speed_dir * target_speed);
} else if (pos_ignore && !vel_ignore && acc_ignore && yaw_ignore && !yaw_rate_ignore) {
// consume velocity and turn rate
rover.mode_guided.set_desired_turn_rate_and_speed(target_turn_rate_cds, speed_dir * target_speed);
} else if (pos_ignore && !vel_ignore && acc_ignore && !yaw_ignore && yaw_rate_ignore) {
// consume velocity
rover.mode_guided.set_desired_heading_and_speed(target_yaw_cd, speed_dir * target_speed);
} else if (pos_ignore && vel_ignore && acc_ignore && !yaw_ignore && yaw_rate_ignore) {
// consume just target heading (probably only skid steering vehicles can do this)
rover.mode_guided.set_desired_heading_and_speed(target_yaw_cd, 0.0f);
} else if (pos_ignore && vel_ignore && acc_ignore && yaw_ignore && !yaw_rate_ignore) {
// consume just turn rate(probably only skid steering vehicles can do this)
rover.mode_guided.set_desired_turn_rate_and_speed(target_turn_rate_cds, 0.0f);
}
break;
}
#if HIL_MODE != HIL_MODE_DISABLED
case MAVLINK_MSG_ID_HIL_STATE:
{
mavlink_hil_state_t packet;
mavlink_msg_hil_state_decode(msg, &packet);
// sanity check location
if (!check_latlng(packet.lat, packet.lon)) {
break;
}
// set gps hil sensor
Location loc;
loc.lat = packet.lat;
loc.lng = packet.lon;
loc.alt = packet.alt/10;
Vector3f vel(packet.vx, packet.vy, packet.vz);
vel *= 0.01f;
gps.setHIL(0, AP_GPS::GPS_OK_FIX_3D,
packet.time_usec/1000,
loc, vel, 10, 0);
// rad/sec
Vector3f gyros;
gyros.x = packet.rollspeed;
gyros.y = packet.pitchspeed;
gyros.z = packet.yawspeed;
// m/s/s
Vector3f accels;
accels.x = packet.xacc * (GRAVITY_MSS/1000.0f);
accels.y = packet.yacc * (GRAVITY_MSS/1000.0f);
accels.z = packet.zacc * (GRAVITY_MSS/1000.0f);
ins.set_gyro(0, gyros);
ins.set_accel(0, accels);
compass.setHIL(0, packet.roll, packet.pitch, packet.yaw);
compass.setHIL(1, packet.roll, packet.pitch, packet.yaw);
break;
}
#endif // HIL_MODE
#if MOUNT == ENABLED
// deprecated. Use MAV_CMD_DO_MOUNT_CONFIGURE
case MAVLINK_MSG_ID_MOUNT_CONFIGURE:
{
rover.camera_mount.configure_msg(msg);
break;
}
// deprecated. Use MAV_CMD_DO_MOUNT_CONTROL
case MAVLINK_MSG_ID_MOUNT_CONTROL:
{
rover.camera_mount.control_msg(msg);
break;
}
#endif // MOUNT == ENABLED
case MAVLINK_MSG_ID_RADIO:
case MAVLINK_MSG_ID_RADIO_STATUS:
{
handle_radio_status(msg, rover.DataFlash, rover.should_log(MASK_LOG_PM));
break;
}
// send or receive fence points with GCS
case MAVLINK_MSG_ID_FENCE_POINT: // MAV ID: 160
case MAVLINK_MSG_ID_FENCE_FETCH_POINT:
rover.g2.fence.handle_msg(*this, msg);
break;
case MAVLINK_MSG_ID_DISTANCE_SENSOR:
rover.rangefinder.handle_msg(msg);
rover.g2.proximity.handle_msg(msg);
break;
default:
handle_common_message(msg);
break;
} // end switch
} // end handle mavlink
void GCS_MAVLINK_Sub::handleMessage(mavlink_message_t* msg)
{
switch (msg->msgid) {
case MAVLINK_MSG_ID_HEARTBEAT: { // MAV ID: 0
// We keep track of the last time we received a heartbeat from our GCS for failsafe purposes
if (msg->sysid != sub.g.sysid_my_gcs) {
break;
}
sub.failsafe.last_heartbeat_ms = AP_HAL::millis();
break;
}
case MAVLINK_MSG_ID_MANUAL_CONTROL: { // MAV ID: 69
if (msg->sysid != sub.g.sysid_my_gcs) {
break; // Only accept control from our gcs
}
mavlink_manual_control_t packet;
mavlink_msg_manual_control_decode(msg, &packet);
if (packet.target != sub.g.sysid_this_mav) {
break; // only accept control aimed at us
}
sub.transform_manual_control_to_rc_override(packet.x,packet.y,packet.z,packet.r,packet.buttons);
sub.failsafe.last_pilot_input_ms = AP_HAL::millis();
// a RC override message is considered to be a 'heartbeat' from the ground station for failsafe purposes
sub.failsafe.last_heartbeat_ms = AP_HAL::millis();
break;
}
case MAVLINK_MSG_ID_RC_CHANNELS_OVERRIDE: { // MAV ID: 70
// allow override of RC input
if (msg->sysid != sub.g.sysid_my_gcs) {
break; // Only accept control from our gcs
}
uint32_t tnow = AP_HAL::millis();
mavlink_rc_channels_override_t packet;
mavlink_msg_rc_channels_override_decode(msg, &packet);
RC_Channels::set_override(0, packet.chan1_raw, tnow);
RC_Channels::set_override(1, packet.chan2_raw, tnow);
RC_Channels::set_override(2, packet.chan3_raw, tnow);
RC_Channels::set_override(3, packet.chan4_raw, tnow);
RC_Channels::set_override(4, packet.chan5_raw, tnow);
RC_Channels::set_override(5, packet.chan6_raw, tnow);
RC_Channels::set_override(6, packet.chan7_raw, tnow);
RC_Channels::set_override(7, packet.chan8_raw, tnow);
sub.failsafe.last_pilot_input_ms = tnow;
// a RC override message is considered to be a 'heartbeat' from the ground station for failsafe purposes
sub.failsafe.last_heartbeat_ms = tnow;
break;
}
case MAVLINK_MSG_ID_SET_ATTITUDE_TARGET: { // MAV ID: 82
// decode packet
mavlink_set_attitude_target_t packet;
mavlink_msg_set_attitude_target_decode(msg, &packet);
// ensure type_mask specifies to use attitude
// the thrust can be used from the altitude hold
if (packet.type_mask & (1<<6)) {
sub.set_attitude_target_no_gps = {AP_HAL::millis(), packet};
}
// ensure type_mask specifies to use attitude and thrust
if ((packet.type_mask & ((1<<7)|(1<<6))) != 0) {
break;
}
// convert thrust to climb rate
packet.thrust = constrain_float(packet.thrust, 0.0f, 1.0f);
float climb_rate_cms = 0.0f;
if (is_equal(packet.thrust, 0.5f)) {
climb_rate_cms = 0.0f;
} else if (packet.thrust > 0.5f) {
// climb at up to WPNAV_SPEED_UP
climb_rate_cms = (packet.thrust - 0.5f) * 2.0f * sub.wp_nav.get_default_speed_up();
} else {
// descend at up to WPNAV_SPEED_DN
climb_rate_cms = (packet.thrust - 0.5f) * 2.0f * fabsf(sub.wp_nav.get_default_speed_down());
}
sub.guided_set_angle(Quaternion(packet.q[0],packet.q[1],packet.q[2],packet.q[3]), climb_rate_cms);
break;
}
case MAVLINK_MSG_ID_SET_POSITION_TARGET_LOCAL_NED: { // MAV ID: 84
// decode packet
mavlink_set_position_target_local_ned_t packet;
mavlink_msg_set_position_target_local_ned_decode(msg, &packet);
// exit if vehicle is not in Guided mode or Auto-Guided mode
if ((sub.control_mode != GUIDED) && !(sub.control_mode == AUTO && sub.auto_mode == Auto_NavGuided)) {
break;
}
// check for supported coordinate frames
if (packet.coordinate_frame != MAV_FRAME_LOCAL_NED &&
packet.coordinate_frame != MAV_FRAME_LOCAL_OFFSET_NED &&
packet.coordinate_frame != MAV_FRAME_BODY_NED &&
packet.coordinate_frame != MAV_FRAME_BODY_OFFSET_NED) {
break;
}
bool pos_ignore = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_POS_IGNORE;
bool vel_ignore = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_VEL_IGNORE;
bool acc_ignore = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_ACC_IGNORE;
/*
* for future use:
* bool force = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_FORCE;
* bool yaw_ignore = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_YAW_IGNORE;
* bool yaw_rate_ignore = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_YAW_RATE_IGNORE;
*/
// prepare position
Vector3f pos_vector;
if (!pos_ignore) {
// convert to cm
pos_vector = Vector3f(packet.x * 100.0f, packet.y * 100.0f, -packet.z * 100.0f);
// rotate to body-frame if necessary
if (packet.coordinate_frame == MAV_FRAME_BODY_NED ||
packet.coordinate_frame == MAV_FRAME_BODY_OFFSET_NED) {
sub.rotate_body_frame_to_NE(pos_vector.x, pos_vector.y);
}
// add body offset if necessary
if (packet.coordinate_frame == MAV_FRAME_LOCAL_OFFSET_NED ||
packet.coordinate_frame == MAV_FRAME_BODY_NED ||
packet.coordinate_frame == MAV_FRAME_BODY_OFFSET_NED) {
pos_vector += sub.inertial_nav.get_position();
} else {
// convert from alt-above-home to alt-above-ekf-origin
pos_vector.z = sub.pv_alt_above_origin(pos_vector.z);
}
}
// prepare velocity
Vector3f vel_vector;
if (!vel_ignore) {
// convert to cm
vel_vector = Vector3f(packet.vx * 100.0f, packet.vy * 100.0f, -packet.vz * 100.0f);
// rotate to body-frame if necessary
if (packet.coordinate_frame == MAV_FRAME_BODY_NED || packet.coordinate_frame == MAV_FRAME_BODY_OFFSET_NED) {
sub.rotate_body_frame_to_NE(vel_vector.x, vel_vector.y);
}
}
// send request
if (!pos_ignore && !vel_ignore && acc_ignore) {
sub.guided_set_destination_posvel(pos_vector, vel_vector);
} else if (pos_ignore && !vel_ignore && acc_ignore) {
sub.guided_set_velocity(vel_vector);
} else if (!pos_ignore && vel_ignore && acc_ignore) {
sub.guided_set_destination(pos_vector);
}
break;
}
case MAVLINK_MSG_ID_SET_POSITION_TARGET_GLOBAL_INT: { // MAV ID: 86
// decode packet
mavlink_set_position_target_global_int_t packet;
mavlink_msg_set_position_target_global_int_decode(msg, &packet);
// exit if vehicle is not in Guided mode or Auto-Guided mode
if ((sub.control_mode != GUIDED) && !(sub.control_mode == AUTO && sub.auto_mode == Auto_NavGuided)) {
break;
}
// check for supported coordinate frames
if (packet.coordinate_frame != MAV_FRAME_GLOBAL &&
packet.coordinate_frame != MAV_FRAME_GLOBAL_INT &&
packet.coordinate_frame != MAV_FRAME_GLOBAL_RELATIVE_ALT && // solo shot manager incorrectly sends RELATIVE_ALT instead of RELATIVE_ALT_INT
packet.coordinate_frame != MAV_FRAME_GLOBAL_RELATIVE_ALT_INT &&
packet.coordinate_frame != MAV_FRAME_GLOBAL_TERRAIN_ALT &&
packet.coordinate_frame != MAV_FRAME_GLOBAL_TERRAIN_ALT_INT) {
break;
}
bool pos_ignore = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_POS_IGNORE;
bool vel_ignore = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_VEL_IGNORE;
bool acc_ignore = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_ACC_IGNORE;
/*
* for future use:
* bool force = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_FORCE;
* bool yaw_ignore = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_YAW_IGNORE;
* bool yaw_rate_ignore = packet.type_mask & MAVLINK_SET_POS_TYPE_MASK_YAW_RATE_IGNORE;
*/
Vector3f pos_neu_cm; // position (North, East, Up coordinates) in centimeters
if (!pos_ignore) {
// sanity check location
if (!check_latlng(packet.lat_int, packet.lon_int)) {
break;
}
Location loc;
loc.lat = packet.lat_int;
loc.lng = packet.lon_int;
loc.alt = packet.alt*100;
switch (packet.coordinate_frame) {
case MAV_FRAME_GLOBAL_RELATIVE_ALT: // solo shot manager incorrectly sends RELATIVE_ALT instead of RELATIVE_ALT_INT
case MAV_FRAME_GLOBAL_RELATIVE_ALT_INT:
loc.relative_alt = true;
loc.terrain_alt = false;
break;
case MAV_FRAME_GLOBAL_TERRAIN_ALT:
case MAV_FRAME_GLOBAL_TERRAIN_ALT_INT:
loc.relative_alt = true;
loc.terrain_alt = true;
break;
case MAV_FRAME_GLOBAL:
case MAV_FRAME_GLOBAL_INT:
default:
loc.relative_alt = false;
loc.terrain_alt = false;
break;
}
pos_neu_cm = sub.pv_location_to_vector(loc);
}
if (!pos_ignore && !vel_ignore && acc_ignore) {
sub.guided_set_destination_posvel(pos_neu_cm, Vector3f(packet.vx * 100.0f, packet.vy * 100.0f, -packet.vz * 100.0f));
} else if (pos_ignore && !vel_ignore && acc_ignore) {
sub.guided_set_velocity(Vector3f(packet.vx * 100.0f, packet.vy * 100.0f, -packet.vz * 100.0f));
} else if (!pos_ignore && vel_ignore && acc_ignore) {
sub.guided_set_destination(pos_neu_cm);
}
break;
}
case MAVLINK_MSG_ID_DISTANCE_SENSOR: {
sub.rangefinder.handle_msg(msg);
break;
}
#if AC_FENCE == ENABLED
// send or receive fence points with GCS
case MAVLINK_MSG_ID_FENCE_POINT: // MAV ID: 160
case MAVLINK_MSG_ID_FENCE_FETCH_POINT:
sub.fence.handle_msg(*this, msg);
break;
#endif // AC_FENCE == ENABLED
case MAVLINK_MSG_ID_TERRAIN_DATA:
case MAVLINK_MSG_ID_TERRAIN_CHECK:
#if AP_TERRAIN_AVAILABLE && AC_TERRAIN
sub.terrain.handle_data(chan, msg);
#endif
break;
case MAVLINK_MSG_ID_SET_HOME_POSITION: {
mavlink_set_home_position_t packet;
mavlink_msg_set_home_position_decode(msg, &packet);
if ((packet.latitude == 0) && (packet.longitude == 0) && (packet.altitude == 0)) {
sub.set_home_to_current_location(true);
} else {
// sanity check location
if (!check_latlng(packet.latitude, packet.longitude)) {
break;
}
Location new_home_loc;
new_home_loc.lat = packet.latitude;
new_home_loc.lng = packet.longitude;
new_home_loc.alt = packet.altitude / 10;
if (sub.far_from_EKF_origin(new_home_loc)) {
break;
}
sub.set_home(new_home_loc, true);
}
break;
}
// This adds support for leak detectors in a separate enclosure
// connected to a mavlink enabled subsystem
case MAVLINK_MSG_ID_SYS_STATUS: {
uint32_t MAV_SENSOR_WATER = 0x20000000;
mavlink_sys_status_t packet;
mavlink_msg_sys_status_decode(msg, &packet);
if ((packet.onboard_control_sensors_enabled & MAV_SENSOR_WATER) && !(packet.onboard_control_sensors_health & MAV_SENSOR_WATER)) {
sub.leak_detector.set_detect();
}
}
break;
default:
handle_common_message(msg);
break;
} // end switch
} // end handle mavlink
