static int pci_arbiter_enabled(void)
{
#if defined(CONFIG_405GP)
return (mfdcr(strap) & PSR_PCI_ARBIT_EN);
#endif
#if defined(CONFIG_405EP)
return (mfdcr(cpc0_pci) & CPC0_PCI_ARBIT_EN);
#endif
#if defined(CONFIG_440GP)
return (mfdcr(cpc0_strp1) & CPC0_STRP1_PAE_MASK);
#endif
#if defined(CONFIG_440GX) || defined(CONFIG_440SP) || defined(CONFIG_440SPE)
unsigned long val;
mfsdr(sdr_xcr, val);
return (val & 0x80000000);
#endif
#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \
defined(CONFIG_440EPX) || defined(CONFIG_440GRX)
unsigned long val;
mfsdr(sdr_pci0, val);
return (val & 0x80000000);
#endif
}
int misc_init_r(void)
{
u32 sdr0_srst1 = 0;
u32 eth_cfg;
/*
* Set EMAC mode/configuration (GMII, SGMII, RGMII...).
* This is board specific, so let's do it here.
*/
mfsdr(SDR0_ETH_CFG, eth_cfg);
/* disable SGMII mode */
eth_cfg &= ~(SDR0_ETH_CFG_SGMII2_ENABLE |
SDR0_ETH_CFG_SGMII1_ENABLE |
SDR0_ETH_CFG_SGMII0_ENABLE);
/* Set the for 2 RGMII mode */
/* GMC0 EMAC4_0, GMC0 EMAC4_1, RGMII Bridge 0 */
eth_cfg &= ~SDR0_ETH_CFG_GMC0_BRIDGE_SEL;
eth_cfg |= SDR0_ETH_CFG_GMC1_BRIDGE_SEL;
mtsdr(SDR0_ETH_CFG, eth_cfg);
/*
* The AHB Bridge core is held in reset after power-on or reset
* so enable it now
*/
mfsdr(SDR0_SRST1, sdr0_srst1);
sdr0_srst1 &= ~SDR0_SRST1_AHB;
mtsdr(SDR0_SRST1, sdr0_srst1);
return 0;
}
int pci_arbiter_enabled(void)
{
#if defined(CONFIG_405GP)
return (mfdcr(CPC0_PSR) & PSR_PCI_ARBIT_EN);
#endif
#if defined(CONFIG_405EP)
return (mfdcr(CPC0_PCI) & CPC0_PCI_ARBIT_EN);
#endif
#if defined(CONFIG_440GP)
return (mfdcr(CPC0_STRP1) & CPC0_STRP1_PAE_MASK);
#endif
#if defined(CONFIG_440GX) || defined(CONFIG_440SP) || defined(CONFIG_440SPE)
unsigned long val;
mfsdr(SDR0_XCR, val);
return (val & 0x80000000);
#endif
#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \
defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \
defined(CONFIG_460EX) || defined(CONFIG_460GT)
unsigned long val;
mfsdr(SDR0_PCI0, val);
return (val & 0x80000000);
#endif
}
/*
* pci_pre_init
*
* This routine is called just prior to registering the hose and gives
* the board the opportunity to check things. Returning a value of zero
* indicates that things are bad & PCI initialization should be aborted.
*
* Different boards may wish to customize the pci controller structure
* (add regions, override default access routines, etc) or perform
* certain pre-initialization actions.
*
*/
int pci_pre_init(struct pci_controller *hose)
{
unsigned long addr;
if (!board_with_pci()) { return 0; }
/*
* Set priority for all PLB3 devices to 0.
* Set PLB3 arbiter to fair mode.
*/
mfsdr(SD0_AMP1, addr);
mtsdr(SD0_AMP1, (addr & 0x000000FF) | 0x0000FF00);
addr = mfdcr(PLB3_ACR);
mtdcr(PLB3_ACR, addr | 0x80000000); /* Sequoia */
/*
* Set priority for all PLB4 devices to 0.
*/
mfsdr(SD0_AMP0, addr);
mtsdr(SD0_AMP0, (addr & 0x000000FF) | 0x0000FF00);
addr = mfdcr(PLB4_ACR) | 0xa0000000; /* Was 0x8---- */
mtdcr(PLB4_ACR, addr); /* Sequoia */
/*
* As of errata version 0.4, CHIP_8: Incorrect Write to DDR SDRAM.
* Workaround: Disable write pipelining to DDR SDRAM by setting
* PLB0_ACR[WRP] = 0.
*/
mtdcr(PLB0_ACR, 0); /* PATCH HAB: WRITE PIPELINING OFF */
/* Segment1 */
mtdcr(PLB1_ACR, 0); /* PATCH HAB: WRITE PIPELINING OFF */
return board_with_pci();
}
int pci_pre_init(struct pci_controller *hose)
{
unsigned long strap;
unsigned long addr;
/*--------------------------------------------------------------------------+
* Bamboo is always configured as the host & requires the
* PCI arbiter to be enabled.
*--------------------------------------------------------------------------*/
mfsdr(sdr_sdstp1, strap);
if ((strap & SDR0_SDSTP1_PAE_MASK) == 0) {
printf("PCI: SDR0_STRP1[PAE] not set.\n");
printf("PCI: Configuration aborted.\n");
return 0;
}
/*-------------------------------------------------------------------------+
| Set priority for all PLB3 devices to 0.
| Set PLB3 arbiter to fair mode.
+-------------------------------------------------------------------------*/
mfsdr(sdr_amp1, addr);
mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00);
addr = mfdcr(plb3_acr);
mtdcr(plb3_acr, addr | 0x80000000);
/*-------------------------------------------------------------------------+
| Set priority for all PLB4 devices to 0.
+-------------------------------------------------------------------------*/
mfsdr(sdr_amp0, addr);
mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00);
addr = mfdcr(plb4_acr) | 0xa0000000; /* Was 0x8---- */
mtdcr(plb4_acr, addr);
/*-------------------------------------------------------------------------+
| Set Nebula PLB4 arbiter to fair mode.
+-------------------------------------------------------------------------*/
/* Segment0 */
addr = (mfdcr(plb0_acr) & ~plb0_acr_ppm_mask) | plb0_acr_ppm_fair;
addr = (addr & ~plb0_acr_hbu_mask) | plb0_acr_hbu_enabled;
addr = (addr & ~plb0_acr_rdp_mask) | plb0_acr_rdp_4deep;
addr = (addr & ~plb0_acr_wrp_mask) | plb0_acr_wrp_2deep;
mtdcr(plb0_acr, addr);
/* Segment1 */
addr = (mfdcr(plb1_acr) & ~plb1_acr_ppm_mask) | plb1_acr_ppm_fair;
addr = (addr & ~plb1_acr_hbu_mask) | plb1_acr_hbu_enabled;
addr = (addr & ~plb1_acr_rdp_mask) | plb1_acr_rdp_4deep;
addr = (addr & ~plb1_acr_wrp_mask) | plb1_acr_wrp_2deep;
mtdcr(plb1_acr, addr);
return 1;
}
phys_size_t initdram(int board_type)
{
#if defined(CONFIG_NAND_SPL)
u32 reg;
/* don't reinit PLL when booting via I2C bootstrap option */
mfsdr(SDR_PINSTP, reg);
if (reg != 0xf0000000)
board_pll_init_f();
#endif
#if !defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
int i;
u32 val;
/* 1. EBC need to program READY, CLK, ADV for ASync mode */
gpio_config(CONFIG_SYS_GPIO_CRAM_CLK, GPIO_OUT, GPIO_SEL, GPIO_OUT_0);
gpio_config(CONFIG_SYS_GPIO_CRAM_ADV, GPIO_OUT, GPIO_SEL, GPIO_OUT_0);
gpio_config(CONFIG_SYS_GPIO_CRAM_CRE, GPIO_OUT, GPIO_SEL, GPIO_OUT_0);
gpio_config(CONFIG_SYS_GPIO_CRAM_WAIT, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG);
/* 2. EBC in Async mode */
mtebc(pb1ap, 0x078F1EC0);
mtebc(pb2ap, 0x078F1EC0);
mtebc(pb1cr, 0x000BC000);
mtebc(pb2cr, 0x020BC000);
/* 3. Set CRAM in Sync mode */
cram_bcr_write(0x7012); /* CRAM burst setting */
/* 4. EBC in Sync mode */
mtebc(pb1ap, 0x9C0201C0);
mtebc(pb2ap, 0x9C0201C0);
/* Set GPIO pins back to alternate function */
gpio_config(CONFIG_SYS_GPIO_CRAM_CLK, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG);
gpio_config(CONFIG_SYS_GPIO_CRAM_ADV, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG);
/* Config EBC to use RDY */
mfsdr(sdrultra0, val);
mtsdr(sdrultra0, val | SDR_ULTRA0_EBCRDYEN);
/* Wait a short while, since for NAND booting this is too fast */
for (i=0; i<200000; i++)
;
#endif
return (CONFIG_SYS_MBYTES_RAM << 20);
}
/*************************************************************************
* int board_early_init_f()
*
************************************************************************/
int board_early_init_f(void)
{
u32 mfr;
mtebc( PB0AP, 0x03800000 ); /* set chip selects */
mtebc( PB0CR, 0xffc58000 ); /* ebc0_b0cr, 4MB at 0xffc00000 CS0 */
mtebc( PB1AP, 0x03800000 );
mtebc( PB1CR, 0xff018000 ); /* ebc0_b1cr, 1MB at 0xff000000 CS1 */
mtebc( PB2AP, 0x03800000 );
mtebc( PB2CR, 0xff838000 ); /* ebc0_b2cr, 2MB at 0xff800000 CS2 */
mtdcr( UIC1SR, 0xffffffff ); /* Clear all interrupts */
mtdcr( UIC1ER, 0x00000000 ); /* disable all interrupts */
mtdcr( UIC1CR, 0x00000000 ); /* Set Critical / Non Critical interrupts */
mtdcr( UIC1PR, 0x7fff83ff ); /* Set Interrupt Polarities */
mtdcr( UIC1TR, 0x001f8000 ); /* Set Interrupt Trigger Levels */
mtdcr( UIC1VR, 0x00000001 ); /* Set Vect base=0,INT31 Highest priority */
mtdcr( UIC1SR, 0x00000000 ); /* clear all interrupts */
mtdcr( UIC1SR, 0xffffffff );
mtdcr( UIC0SR, 0xffffffff ); /* Clear all interrupts */
mtdcr( UIC0ER, 0x00000000 ); /* disable all interrupts excepted cascade */
mtdcr( UIC0CR, 0x00000001 ); /* Set Critical / Non Critical interrupts */
mtdcr( UIC0PR, 0xffffffff ); /* Set Interrupt Polarities */
mtdcr( UIC0TR, 0x01000004 ); /* Set Interrupt Trigger Levels */
mtdcr( UIC0VR, 0x00000001 ); /* Set Vect base=0,INT31 Highest priority */
mtdcr( UIC0SR, 0x00000000 ); /* clear all interrupts */
mtdcr( UIC0SR, 0xffffffff );
mfsdr(SDR0_MFR, mfr);
mfr |= SDR0_MFR_FIXD; /* Workaround for PCI/DMA */
mtsdr(SDR0_MFR, mfr);
return 0;
}
int board_with_pci(void)
{
u32 reg;
mfsdr(SDR0_PCI0, reg);
return (reg & SDR0_XCR_PAE_MASK);
}
/*************************************************************************
* int board_early_init_f()
*
************************************************************************/
int board_early_init_f(void)
{
u32 mfr;
mtebc( pb0ap, 0x03800000 ); /* set chip selects */
mtebc( pb0cr, 0xffc58000 ); /* ebc0_b0cr, 4MB at 0xffc00000 CS0 */
mtebc( pb1ap, 0x03800000 );
mtebc( pb1cr, 0xff018000 ); /* ebc0_b1cr, 1MB at 0xff000000 CS1 */
mtebc( pb2ap, 0x03800000 );
mtebc( pb2cr, 0xff838000 ); /* ebc0_b2cr, 2MB at 0xff800000 CS2 */
mtdcr( uic1sr, 0xffffffff ); /* Clear all interrupts */
mtdcr( uic1er, 0x00000000 ); /* disable all interrupts */
mtdcr( uic1cr, 0x00000000 ); /* Set Critical / Non Critical interrupts */
mtdcr( uic1pr, 0x7fff83ff ); /* Set Interrupt Polarities */
mtdcr( uic1tr, 0x001f8000 ); /* Set Interrupt Trigger Levels */
mtdcr( uic1vr, 0x00000001 ); /* Set Vect base=0,INT31 Highest priority */
mtdcr( uic1sr, 0x00000000 ); /* clear all interrupts */
mtdcr( uic1sr, 0xffffffff );
mtdcr( uic0sr, 0xffffffff ); /* Clear all interrupts */
mtdcr( uic0er, 0x00000000 ); /* disable all interrupts excepted cascade */
mtdcr( uic0cr, 0x00000001 ); /* Set Critical / Non Critical interrupts */
mtdcr( uic0pr, 0xffffffff ); /* Set Interrupt Polarities */
mtdcr( uic0tr, 0x01000004 ); /* Set Interrupt Trigger Levels */
mtdcr( uic0vr, 0x00000001 ); /* Set Vect base=0,INT31 Highest priority */
mtdcr( uic0sr, 0x00000000 ); /* clear all interrupts */
mtdcr( uic0sr, 0xffffffff );
mfsdr(sdr_mfr, mfr);
mfr |= SDR0_MFR_FIXD; /* Workaround for PCI/DMA */
mtsdr(sdr_mfr, mfr);
return 0;
}
static int bootstrap_option(void)
{
unsigned long val;
mfsdr(SDR_PINSTP, val);
return ((val & 0xf0000000) >> SDR0_PINSTP_SHIFT);
}
void ClockOn(const rtems_irq_connect_data* unused)
{
uint32_t iocr, r;
ppc_cpu_id_t cpu;
Clock_driver_ticks = 0;
cpu = get_ppc_cpu_type();
if (cpu==PPC_405GP) {
iocr = mfdcr(CPC0_CR1);
if (bsp_timer_internal_clock) iocr &= ~CR1_CETE ;/* timer clocked from system clock */
else iocr |= CR1_CETE; /* select external timer clock */
mtdcr(CPC0_CR1,iocr);
} else if (cpu==PPC_405EX) {
mfsdr(SDR0_C405,iocr);
if (bsp_timer_internal_clock) iocr &= ~SDR_CETE ;/* timer clocked from system clock */
else iocr |= SDR_CETE; /* select external timer clock */
mtsdr(SDR0_C405,iocr);
} else {
printk("clock.c:unrecognised CPU");
rtems_fatal_error_occurred(1);
}
pit_value = rtems_configuration_get_microseconds_per_tick() * bsp_clicks_per_usec;
mtspr(PIT,pit_value);
tick_time = mfspr(TBL) + pit_value;
r = mfspr(TCR);
mtspr(TCR, r | PIE | ARE);
}
int pci_pre_init(struct pci_controller * hose )
{
unsigned long strap;
/* See if we're supposed to setup the pci */
mfsdr(sdr_sdstp1, strap);
if ((strap & 0x00010000) == 0) {
return (0);
}
#if defined(CFG_PCI_FORCE_PCI_CONV)
/* Setup System Device Register PCIX0_XCR */
mfsdr(sdr_xcr, strap);
strap &= 0x0f000000;
mtsdr(sdr_xcr, strap);
#endif
return 1;
}
static void
InitUARTClock(void)
{
uint32_t reg;
mfsdr(SDR0_UART0,reg);
reg &= ~0x008000FF;
reg |= 0x00800001; /* Ext clock, div 1 */
mtsdr(SDR0_UART0,reg);
}
int checkboard(void)
{
u16 *hwVersReg = (u16 *) HCU_HW_VERSION_REGISTER;
u16 *boardVersReg = (u16 *) HCU_CPLD_VERSION_REGISTER;
u16 generation = in_be16(boardVersReg) & 0xf0;
u16 index = in_be16(boardVersReg) & 0x0f;
u32 ecid0, ecid1, ecid2, ecid3;
nm_show_print(generation, index, in_be16(hwVersReg) & 0xff);
mfsdr(SDR0_ECID0, ecid0);
mfsdr(SDR0_ECID1, ecid1);
mfsdr(SDR0_ECID2, ecid2);
mfsdr(SDR0_ECID3, ecid3);
printf("Chip ID 0x%x 0x%x 0x%x 0x%x\n", ecid0, ecid1, ecid2, ecid3);
return 0;
}
int pci_pre_init(struct pci_controller * hose)
{
unsigned long strap;
/* See if we're supposed to setup the pci */
mfsdr(SDR0_SDSTP1, strap);
if ((strap & 0x00010000) == 0)
return 0;
#if defined(CONFIG_SYS_PCI_FORCE_PCI_CONV)
/* Setup System Device Register PCIL0_XCR */
mfsdr(SDR0_XCR, strap);
strap &= 0x0f000000;
mtsdr(SDR0_XCR, strap);
#endif
return 1;
}
/*
* pci_pre_init
*
* This routine is called just prior to registering the hose and gives
* the board the opportunity to check things. Returning a value of zero
* indicates that things are bad & PCI initialization should be aborted.
*
* Different boards may wish to customize the pci controller structure
* (add regions, override default access routines, etc) or perform
* certain pre-initialization actions.
*
*/
int __pci_pre_init(struct pci_controller *hose)
{
u32 reg;
/*
* Set priority for all PLB3 devices to 0.
* Set PLB3 arbiter to fair mode.
*/
mfsdr(SDR0_AMP1, reg);
mtsdr(SDR0_AMP1, (reg & 0x000000FF) | 0x0000FF00);
reg = mfdcr(PLB3A0_ACR);
mtdcr(PLB3A0_ACR, reg | 0x80000000);
/*
* Set priority for all PLB4 devices to 0.
*/
mfsdr(SDR0_AMP0, reg);
mtsdr(SDR0_AMP0, (reg & 0x000000FF) | 0x0000FF00);
reg = mfdcr(PLB4A0_ACR) | 0xa0000000;
mtdcr(PLB4A0_ACR, reg);
/*
* Set Nebula PLB4 arbiter to fair mode.
*/
/* Segment0 */
reg = (mfdcr(PLB4A0_ACR) & ~PLB4Ax_ACR_PPM_MASK) | PLB4Ax_ACR_PPM_FAIR;
reg = (reg & ~PLB4Ax_ACR_HBU_MASK) | PLB4Ax_ACR_HBU_ENABLED;
reg = (reg & ~PLB4Ax_ACR_RDP_MASK) | PLB4Ax_ACR_RDP_4DEEP;
reg = (reg & ~PLB4Ax_ACR_WRP_MASK) | PLB4Ax_ACR_WRP_2DEEP;
mtdcr(PLB4A0_ACR, reg);
/* Segment1 */
reg = (mfdcr(PLB4A1_ACR) & ~PLB4Ax_ACR_PPM_MASK) | PLB4Ax_ACR_PPM_FAIR;
reg = (reg & ~PLB4Ax_ACR_HBU_MASK) | PLB4Ax_ACR_HBU_ENABLED;
reg = (reg & ~PLB4Ax_ACR_RDP_MASK) | PLB4Ax_ACR_RDP_4DEEP;
reg = (reg & ~PLB4Ax_ACR_WRP_MASK) | PLB4Ax_ACR_WRP_2DEEP;
mtdcr(PLB4A1_ACR, reg);
#if defined(CONFIG_SYS_PCI_BOARD_FIXUP_IRQ)
hose->fixup_irq = board_pci_fixup_irq;
#endif
return 1;
}
static int i2c_bootrom_enabled(void)
{
#if defined(CONFIG_405EP)
return (mfdcr(cpc0_boot) & CPC0_BOOT_SEP);
#else
unsigned long val;
mfsdr(sdr_sdcs, val);
return (val & SDR0_SDCS_SDD);
#endif
}
int pci_pre_init(struct pci_controller *hose)
{
unsigned long addr;
/*-------------------------------------------------------------------------+
| Set priority for all PLB3 devices to 0.
| Set PLB3 arbiter to fair mode.
+-------------------------------------------------------------------------*/
mfsdr(sdr_amp1, addr);
mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00);
addr = mfdcr(plb3_acr);
mtdcr(plb3_acr, addr | 0x80000000);
/*-------------------------------------------------------------------------+
| Set priority for all PLB4 devices to 0.
+-------------------------------------------------------------------------*/
mfsdr(sdr_amp0, addr);
mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00);
addr = mfdcr(plb4_acr) | 0xa0000000; /* Was 0x8---- */
mtdcr(plb4_acr, addr);
/*-------------------------------------------------------------------------+
| Set Nebula PLB4 arbiter to fair mode.
+-------------------------------------------------------------------------*/
/* Segment0 */
addr = (mfdcr(plb0_acr) & ~plb0_acr_ppm_mask) | plb0_acr_ppm_fair;
addr = (addr & ~plb0_acr_hbu_mask) | plb0_acr_hbu_enabled;
addr = (addr & ~plb0_acr_rdp_mask) | plb0_acr_rdp_4deep;
addr = (addr & ~plb0_acr_wrp_mask) | plb0_acr_wrp_2deep;
mtdcr(plb0_acr, addr);
/* Segment1 */
addr = (mfdcr(plb1_acr) & ~plb1_acr_ppm_mask) | plb1_acr_ppm_fair;
addr = (addr & ~plb1_acr_hbu_mask) | plb1_acr_hbu_enabled;
addr = (addr & ~plb1_acr_rdp_mask) | plb1_acr_rdp_4deep;
addr = (addr & ~plb1_acr_wrp_mask) | plb1_acr_wrp_2deep;
mtdcr(plb1_acr, addr);
return 1;
}
void get_sys_info (sys_info_t *sysInfo)
{
unsigned long temp;
unsigned long reg;
unsigned long lfdiv;
unsigned long m;
unsigned long prbdv0;
/*
WARNING: ASSUMES the following:
ENG=1
PRADV0=1
PRBDV0=1
*/
/* Decode CPR0_PLLD0 for divisors */
mfclk(clk_plld, reg);
temp = (reg & PLLD_FWDVA_MASK) >> 16;
sysInfo->pllFwdDivA = temp ? temp : 16;
temp = (reg & PLLD_FWDVB_MASK) >> 8;
sysInfo->pllFwdDivB = temp ? temp: 8 ;
temp = (reg & PLLD_FBDV_MASK) >> 24;
sysInfo->pllFbkDiv = temp ? temp : 32;
lfdiv = reg & PLLD_LFBDV_MASK;
mfclk(clk_opbd, reg);
temp = (reg & OPBDDV_MASK) >> 24;
sysInfo->pllOpbDiv = temp ? temp : 4;
mfclk(clk_perd, reg);
temp = (reg & PERDV_MASK) >> 24;
sysInfo->pllExtBusDiv = temp ? temp : 8;
mfclk(clk_primbd, reg);
temp = (reg & PRBDV_MASK) >> 24;
prbdv0 = temp ? temp : 8;
mfclk(clk_spcid, reg);
temp = (reg & SPCID_MASK) >> 24;
sysInfo->pllPciDiv = temp ? temp : 4;
/* Calculate 'M' based on feedback source */
mfsdr(sdr_sdstp0, reg);
temp = (reg & PLLSYS0_SEL_MASK) >> 27;
if (temp == 0) { /* PLL output */
/* Figure which pll to use */
mfclk(clk_pllc, reg);
temp = (reg & PLLC_SRC_MASK) >> 29;
if (!temp) /* PLLOUTA */
m = sysInfo->pllFbkDiv * lfdiv * sysInfo->pllFwdDivA;
else /* PLLOUTB */
m = sysInfo->pllFbkDiv * lfdiv * sysInfo->pllFwdDivB;
}
static int pci_async_enabled(void)
{
#if defined(CONFIG_405GP)
return (mfdcr(strap) & PSR_PCI_ASYNC_EN);
#endif
#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \
defined(CONFIG_440EPX) || defined(CONFIG_440GRX)
unsigned long val;
mfsdr(sdr_sdstp1, val);
return (val & SDR0_SDSTP1_PAME_MASK);
#endif
}
static void
dwctwo_plb_attach(device_t parent, device_t self, void *aux)
{
struct dwc2_softc *sc = device_private(self);
struct plb_attach_args *paa = aux;
prop_dictionary_t dict = device_properties(self);
uint32_t srst0;
sc->sc_dev = self;
/* get core parameters */
if (!prop_dictionary_get_uint32(dict, "params",
(uint32_t *)&sc->sc_params)) {
aprint_error("struct dwc2_core_params not found\n");
return;
}
dwctwo_tag.pbs_base = paa->plb_addr;
dwctwo_tag.pbs_limit += paa->plb_addr;
if (bus_space_init(&dwctwo_tag, "dwctwotag", ex_storage,
sizeof(ex_storage)))
panic("dwctwo_attach: Failed to initialise opb_tag");
sc->sc_iot = &dwctwo_tag;
bus_space_map(sc->sc_iot, paa->plb_addr, DWCTWO_SIZE, 0, &sc->sc_ioh);
sc->sc_bus.dmatag = paa->plb_dmat;
intr_establish(paa->plb_irq, IST_LEVEL, IPL_SCHED, dwc2_intr, sc);
/* Enable the USB interface. */
mtsdr(DCR_SDR0_PFC1, mfsdr(DCR_SDR0_PFC1) | SDR0_PFC1_USBEN);
srst0 = mfsdr(DCR_SDR0_SRST0);
mtsdr(DCR_SDR0_SRST0, srst0 | SDR0_SRST0_UPRST | SDR0_SRST0_AHB);
delay(200 * 1000); /* XXXX */
mtsdr(DCR_SDR0_SRST0, srst0);
config_defer(self, dwctwo_plb_deferred);
}
int misc_init_f (void)
{
uint reg;
out16(FPGA_REG10, (in16(FPGA_REG10) &
~(FPGA_REG10_AUTO_NEG_DIS|FPGA_REG10_RESET_ETH)) |
FPGA_REG10_10MHZ_ENABLE |
FPGA_REG10_100MHZ_ENABLE |
FPGA_REG10_GIGABIT_ENABLE |
FPGA_REG10_FULL_DUPLEX );
udelay(10000); /* wait 10ms */
out16(FPGA_REG10, (in16(FPGA_REG10) | FPGA_REG10_RESET_ETH));
/* minimal init for PCIe */
/* pci express 0 Endpoint Mode */
mfsdr(SDRN_PESDR_DLPSET(0), reg);
reg &= (~0x00400000);
mtsdr(SDRN_PESDR_DLPSET(0), reg);
/* pci express 1 Rootpoint Mode */
mfsdr(SDRN_PESDR_DLPSET(1), reg);
reg |= 0x00400000;
mtsdr(SDRN_PESDR_DLPSET(1), reg);
/* pci express 2 Rootpoint Mode */
mfsdr(SDRN_PESDR_DLPSET(2), reg);
reg |= 0x00400000;
mtsdr(SDRN_PESDR_DLPSET(2), reg);
out16(FPGA_REG1C,(in16 (FPGA_REG1C) &
~FPGA_REG1C_PE0_ROOTPOINT &
~FPGA_REG1C_PE1_ENDPOINT &
~FPGA_REG1C_PE2_ENDPOINT));
return 0;
}
int board_early_init_f(void)
{
unsigned int reg;
#if !defined(CONFIG_NAND_U_BOOT)
/* don't reinit PLL when booting via I2C bootstrap option */
mfsdr(SDR_PINSTP, reg);
if (reg != 0xf0000000)
board_pll_init_f();
#endif
acadia_gpio_init();
/* Configure 405EZ for NAND usage */
mtsdr(sdrnand0, SDR_NAND0_NDEN | SDR_NAND0_NDAREN | SDR_NAND0_NDRBEN);
mfsdr(sdrultra0, reg);
reg &= ~SDR_ULTRA0_CSN_MASK;
reg |= (SDR_ULTRA0_CSNSEL0 >> CONFIG_SYS_NAND_CS) |
SDR_ULTRA0_NDGPIOBP |
SDR_ULTRA0_EBCRDYEN |
SDR_ULTRA0_NFSRSTEN;
mtsdr(sdrultra0, reg);
/* USB Host core needs this bit set */
mfsdr(sdrultra1, reg);
mtsdr(sdrultra1, reg | SDR_ULTRA1_LEDNENABLE);
mtdcr(uicsr, 0xFFFFFFFF); /* clear all ints */
mtdcr(uicer, 0x00000000); /* disable all ints */
mtdcr(uiccr, 0x00000010);
mtdcr(uicpr, 0xFE7FFFF0); /* set int polarities */
mtdcr(uictr, 0x00000010); /* set int trigger levels */
mtdcr(uicsr, 0xFFFFFFFF); /* clear all ints */
return 0;
}
int pci_pre_init(struct pci_controller * hose )
{
unsigned long strap;
/*-------------------------------------------------------------------+
* The yucca board is always configured as the host & requires the
* PCI arbiter to be enabled.
*-------------------------------------------------------------------*/
mfsdr(sdr_sdstp1, strap);
if( (strap & SDR0_SDSTP1_PAE_MASK) == 0 ) {
printf("PCI: SDR0_STRP1[%08lX] - PCI Arbiter disabled.\n",strap);
return 0;
}
return 1;
}
int board_early_init_f(void)
{
register uint reg;
set_leds(0); /* display boot info counter */
/*--------------------------------------------------------------------
* Setup the external bus controller/chip selects
*-------------------------------------------------------------------*/
mtdcr(ebccfga, xbcfg);
reg = mfdcr(ebccfgd);
mtdcr(ebccfgd, reg | 0x04000000); /* Set ATC */
/*--------------------------------------------------------------------
* GPIO's are alreay setup in cpu/ppc4xx/cpu_init.c
* via define from board config file.
*-------------------------------------------------------------------*/
/*--------------------------------------------------------------------
* Setup the interrupt controller polarities, triggers, etc.
*-------------------------------------------------------------------*/
mtdcr(uic0sr, 0xffffffff); /* clear all */
mtdcr(uic0er, 0x00000000); /* disable all */
mtdcr(uic0cr, 0x00000001); /* UIC1 crit is critical */
mtdcr(uic0pr, 0xfffffe1f); /* per ref-board manual */
mtdcr(uic0tr, 0x01c00000); /* per ref-board manual */
mtdcr(uic0vr, 0x00000001); /* int31 highest, base=0x000 */
mtdcr(uic0sr, 0xffffffff); /* clear all */
mtdcr(uic1sr, 0xffffffff); /* clear all */
mtdcr(uic1er, 0x00000000); /* disable all */
mtdcr(uic1cr, 0x00000000); /* all non-critical */
mtdcr(uic1pr, 0xffffe0ff); /* per ref-board manual */
mtdcr(uic1tr, 0x00ffc000); /* per ref-board manual */
mtdcr(uic1vr, 0x00000001); /* int31 highest, base=0x000 */
mtdcr(uic1sr, 0xffffffff); /* clear all */
/*--------------------------------------------------------------------
* Setup other serial configuration
*-------------------------------------------------------------------*/
mfsdr(sdr_pci0, reg);
mtsdr(sdr_pci0, 0x80000000 | reg); /* PCI arbiter enabled */
mtsdr(sdr_pfc0, 0x00000100); /* Pin function: enable GPIO49-63 */
mtsdr(sdr_pfc1, 0x00048000); /* Pin function: UART0 has 4 pins, select IRQ5 */
return 0;
}
phys_size_t initdram(int board_type)
{
int i;
u32 val;
/* 1. EBC need to program READY, CLK, ADV for ASync mode */
gpio_config(CONFIG_SYS_GPIO_CRAM_CLK, GPIO_OUT, GPIO_SEL, GPIO_OUT_0);
gpio_config(CONFIG_SYS_GPIO_CRAM_ADV, GPIO_OUT, GPIO_SEL, GPIO_OUT_0);
gpio_config(CONFIG_SYS_GPIO_CRAM_CRE, GPIO_OUT, GPIO_SEL, GPIO_OUT_0);
gpio_config(CONFIG_SYS_GPIO_CRAM_WAIT, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG);
/* 2. EBC in Async mode */
mtebc(PB1AP, 0x078F1EC0);
mtebc(PB2AP, 0x078F1EC0);
mtebc(PB1CR, 0x000BC000);
mtebc(PB2CR, 0x020BC000);
/* 3. Set CRAM in Sync mode */
cram_bcr_write(0x7012); /* CRAM burst setting */
/* 4. EBC in Sync mode */
mtebc(PB1AP, 0x9C0201C0);
mtebc(PB2AP, 0x9C0201C0);
/* Set GPIO pins back to alternate function */
gpio_config(CONFIG_SYS_GPIO_CRAM_CLK, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG);
gpio_config(CONFIG_SYS_GPIO_CRAM_ADV, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG);
/* Config EBC to use RDY */
mfsdr(SDR0_ULTRA0, val);
mtsdr(SDR0_ULTRA0, val | SDR_ULTRA0_EBCRDYEN);
/* Wait a short while, since for NAND booting this is too fast */
for (i=0; i<200000; i++)
;
return (CONFIG_SYS_MBYTES_RAM << 20);
}
int board_early_init_f (void)
{
unsigned long mfr;
unsigned char *fpga_base = (unsigned char *) CONFIG_SYS_FPGA_BASE;
unsigned char switch_status;
unsigned long cs0_base;
unsigned long cs0_size;
unsigned long cs0_twt;
unsigned long cs2_base;
unsigned long cs2_size;
unsigned long cs2_twt;
/*-------------------------------------------------------------------------+
| Initialize EBC CONFIG
+-------------------------------------------------------------------------*/
mtebc(EBC0_CFG, EBC_CFG_LE_UNLOCK |
EBC_CFG_PTD_ENABLE | EBC_CFG_RTC_64PERCLK |
EBC_CFG_ATC_PREVIOUS | EBC_CFG_DTC_PREVIOUS |
EBC_CFG_CTC_PREVIOUS | EBC_CFG_EMC_NONDEFAULT |
EBC_CFG_PME_DISABLE | EBC_CFG_PR_32);
/*-------------------------------------------------------------------------+
| FPGA. Initialize bank 7 with default values.
+-------------------------------------------------------------------------*/
mtebc(PB7AP, EBC_BXAP_BME_DISABLED|EBC_BXAP_TWT_ENCODE(7)|
EBC_BXAP_BCE_DISABLE|
EBC_BXAP_CSN_ENCODE(1)|EBC_BXAP_OEN_ENCODE(1)|
EBC_BXAP_WBN_ENCODE(1)|EBC_BXAP_WBF_ENCODE(1)|
EBC_BXAP_TH_ENCODE(1)|EBC_BXAP_RE_DISABLED|
EBC_BXAP_BEM_WRITEONLY|
EBC_BXAP_PEN_DISABLED);
mtebc(PB7CR, EBC_BXCR_BAS_ENCODE(0x48300000)|
EBC_BXCR_BS_1MB|EBC_BXCR_BU_RW|EBC_BXCR_BW_8BIT);
/* read FPGA base register FPGA_REG0 */
switch_status = *fpga_base;
if (switch_status & 0x40) {
cs0_base = 0xFFE00000;
cs0_size = EBC_BXCR_BS_2MB;
cs0_twt = 8;
cs2_base = 0xFF800000;
cs2_size = EBC_BXCR_BS_4MB;
cs2_twt = 10;
} else {
cs0_base = 0xFFC00000;
cs0_size = EBC_BXCR_BS_4MB;
cs0_twt = 10;
cs2_base = 0xFF800000;
cs2_size = EBC_BXCR_BS_2MB;
cs2_twt = 8;
}
/*-------------------------------------------------------------------------+
| 1 MB FLASH / 1 MB SRAM. Initialize bank 0 with default values.
+-------------------------------------------------------------------------*/
mtebc(PB0AP, EBC_BXAP_BME_DISABLED|EBC_BXAP_TWT_ENCODE(cs0_twt)|
EBC_BXAP_BCE_DISABLE|
EBC_BXAP_CSN_ENCODE(1)|EBC_BXAP_OEN_ENCODE(1)|
EBC_BXAP_WBN_ENCODE(1)|EBC_BXAP_WBF_ENCODE(1)|
EBC_BXAP_TH_ENCODE(1)|EBC_BXAP_RE_DISABLED|
EBC_BXAP_BEM_WRITEONLY|
EBC_BXAP_PEN_DISABLED);
mtebc(PB0CR, EBC_BXCR_BAS_ENCODE(cs0_base)|
cs0_size|EBC_BXCR_BU_RW|EBC_BXCR_BW_8BIT);
/*-------------------------------------------------------------------------+
| 8KB NVRAM/RTC. Initialize bank 1 with default values.
+-------------------------------------------------------------------------*/
mtebc(PB1AP, EBC_BXAP_BME_DISABLED|EBC_BXAP_TWT_ENCODE(10)|
EBC_BXAP_BCE_DISABLE|
EBC_BXAP_CSN_ENCODE(1)|EBC_BXAP_OEN_ENCODE(1)|
EBC_BXAP_WBN_ENCODE(1)|EBC_BXAP_WBF_ENCODE(1)|
EBC_BXAP_TH_ENCODE(1)|EBC_BXAP_RE_DISABLED|
EBC_BXAP_BEM_WRITEONLY|
EBC_BXAP_PEN_DISABLED);
mtebc(PB1CR, EBC_BXCR_BAS_ENCODE(0x48000000)|
EBC_BXCR_BS_1MB|EBC_BXCR_BU_RW|EBC_BXCR_BW_8BIT);
/*-------------------------------------------------------------------------+
| 4 MB FLASH. Initialize bank 2 with default values.
+-------------------------------------------------------------------------*/
mtebc(PB2AP, EBC_BXAP_BME_DISABLED|EBC_BXAP_TWT_ENCODE(cs2_twt)|
EBC_BXAP_BCE_DISABLE|
EBC_BXAP_CSN_ENCODE(1)|EBC_BXAP_OEN_ENCODE(1)|
EBC_BXAP_WBN_ENCODE(1)|EBC_BXAP_WBF_ENCODE(1)|
EBC_BXAP_TH_ENCODE(1)|EBC_BXAP_RE_DISABLED|
EBC_BXAP_BEM_WRITEONLY|
EBC_BXAP_PEN_DISABLED);
mtebc(PB2CR, EBC_BXCR_BAS_ENCODE(cs2_base)|
cs2_size|EBC_BXCR_BU_RW|EBC_BXCR_BW_8BIT);
/*-------------------------------------------------------------------------+
| FPGA. Initialize bank 7 with default values.
+-------------------------------------------------------------------------*/
mtebc(PB7AP, EBC_BXAP_BME_DISABLED|EBC_BXAP_TWT_ENCODE(7)|
EBC_BXAP_BCE_DISABLE|
EBC_BXAP_CSN_ENCODE(1)|EBC_BXAP_OEN_ENCODE(1)|
EBC_BXAP_WBN_ENCODE(1)|EBC_BXAP_WBF_ENCODE(1)|
EBC_BXAP_TH_ENCODE(1)|EBC_BXAP_RE_DISABLED|
EBC_BXAP_BEM_WRITEONLY|
EBC_BXAP_PEN_DISABLED);
mtebc(PB7CR, EBC_BXCR_BAS_ENCODE(0x48300000)|
EBC_BXCR_BS_1MB|EBC_BXCR_BU_RW|EBC_BXCR_BW_8BIT);
/*--------------------------------------------------------------------
* Setup the interrupt controller polarities, triggers, etc.
*-------------------------------------------------------------------*/
/*
* Because of the interrupt handling rework to handle 440GX interrupts
* with the common code, we needed to change names of the UIC registers.
* Here the new relationship:
*
* U-Boot name 440GX name
* -----------------------
* UIC0 UICB0
* UIC1 UIC0
* UIC2 UIC1
* UIC3 UIC2
*/
mtdcr (UIC1SR, 0xffffffff); /* clear all */
mtdcr (UIC1ER, 0x00000000); /* disable all */
mtdcr (UIC1CR, 0x00000009); /* SMI & UIC1 crit are critical */
mtdcr (UIC1PR, 0xfffffe13); /* per ref-board manual */
mtdcr (UIC1TR, 0x01c00008); /* per ref-board manual */
mtdcr (UIC1VR, 0x00000001); /* int31 highest, base=0x000 */
mtdcr (UIC1SR, 0xffffffff); /* clear all */
mtdcr (UIC2SR, 0xffffffff); /* clear all */
mtdcr (UIC2ER, 0x00000000); /* disable all */
mtdcr (UIC2CR, 0x00000000); /* all non-critical */
mtdcr (UIC2PR, 0xffffe0ff); /* per ref-board manual */
mtdcr (UIC2TR, 0x00ffc000); /* per ref-board manual */
mtdcr (UIC2VR, 0x00000001); /* int31 highest, base=0x000 */
mtdcr (UIC2SR, 0xffffffff); /* clear all */
mtdcr (UIC3SR, 0xffffffff); /* clear all */
mtdcr (UIC3ER, 0x00000000); /* disable all */
mtdcr (UIC3CR, 0x00000000); /* all non-critical */
mtdcr (UIC3PR, 0xffffffff); /* per ref-board manual */
mtdcr (UIC3TR, 0x00ff8c0f); /* per ref-board manual */
mtdcr (UIC3VR, 0x00000001); /* int31 highest, base=0x000 */
mtdcr (UIC3SR, 0xffffffff); /* clear all */
mtdcr (UIC0SR, 0xfc000000); /* clear all */
mtdcr (UIC0ER, 0x00000000); /* disable all */
mtdcr (UIC0CR, 0x00000000); /* all non-critical */
mtdcr (UIC0PR, 0xfc000000); /* */
mtdcr (UIC0TR, 0x00000000); /* */
mtdcr (UIC0VR, 0x00000001); /* */
mfsdr (SDR0_MFR, mfr);
mfr &= ~SDR0_MFR_ECS_MASK;
/* mtsdr(SDR0_MFR, mfr); */
fpga_init();
return 0;
}
void fpga_init(void)
{
unsigned long group;
unsigned long sdr0_pfc0;
unsigned long sdr0_pfc1;
unsigned long sdr0_cust0;
unsigned long pvr;
mfsdr (SDR0_PFC0, sdr0_pfc0);
mfsdr (SDR0_PFC1, sdr0_pfc1);
group = SDR0_PFC1_EPS_DECODE(sdr0_pfc1);
pvr = get_pvr ();
sdr0_pfc0 = (sdr0_pfc0 & ~SDR0_PFC0_GEIE_MASK) | SDR0_PFC0_GEIE_TRE;
if ( ((pvr == PVR_440GX_RA) || (pvr == PVR_440GX_RB)) && ((group == 4) || (group == 5))) {
sdr0_pfc0 = (sdr0_pfc0 & ~SDR0_PFC0_TRE_MASK) | SDR0_PFC0_TRE_DISABLE;
sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_CTEMS_MASK) | SDR0_PFC1_CTEMS_EMS;
out8(FPGA_REG2, (in8(FPGA_REG2) & ~FPGA_REG2_EXT_INTFACE_MASK) |
FPGA_REG2_EXT_INTFACE_ENABLE);
mtsdr (SDR0_PFC0, sdr0_pfc0);
mtsdr (SDR0_PFC1, sdr0_pfc1);
} else {
sdr0_pfc0 = (sdr0_pfc0 & ~SDR0_PFC0_TRE_MASK) | SDR0_PFC0_TRE_ENABLE;
switch (group)
{
case 0:
case 1:
case 2:
/* CPU trace A */
out8(FPGA_REG2, (in8(FPGA_REG2) & ~FPGA_REG2_EXT_INTFACE_MASK) |
FPGA_REG2_EXT_INTFACE_ENABLE);
sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_CTEMS_MASK) | SDR0_PFC1_CTEMS_EMS;
mtsdr (SDR0_PFC0, sdr0_pfc0);
mtsdr (SDR0_PFC1, sdr0_pfc1);
break;
case 3:
case 4:
case 5:
case 6:
/* CPU trace B - Over EBMI */
sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_CTEMS_MASK) | SDR0_PFC1_CTEMS_CPUTRACE;
mtsdr (SDR0_PFC0, sdr0_pfc0);
mtsdr (SDR0_PFC1, sdr0_pfc1);
out8(FPGA_REG2, (in8(FPGA_REG2) & ~FPGA_REG2_EXT_INTFACE_MASK) |
FPGA_REG2_EXT_INTFACE_DISABLE);
break;
}
}
/* Initialize the ethernet specific functions in the fpga */
mfsdr(SDR0_PFC1, sdr0_pfc1);
mfsdr(SDR0_CUST0, sdr0_cust0);
if ( (SDR0_PFC1_EPS_DECODE(sdr0_pfc1) == 4) &&
((SDR0_CUST0_RGMII2_DECODE(sdr0_cust0) == RGMII_FER_GMII) ||
(SDR0_CUST0_RGMII2_DECODE(sdr0_cust0) == RGMII_FER_TBI)))
{
if ((in8(FPGA_REG0) & FPGA_REG0_ECLS_MASK) == FPGA_REG0_ECLS_VER1)
{
out8(FPGA_REG3, (in8(FPGA_REG3) & ~FPGA_REG3_ENET_MASK1) |
FPGA_REG3_ENET_GROUP7);
}
else
{
if (SDR0_CUST0_RGMII2_DECODE(sdr0_cust0) == RGMII_FER_GMII)
{
out8(FPGA_REG3, (in8(FPGA_REG3) & ~FPGA_REG3_ENET_MASK2) |
FPGA_REG3_ENET_GROUP7);
}
else
{
out8(FPGA_REG3, (in8(FPGA_REG3) & ~FPGA_REG3_ENET_MASK2) |
FPGA_REG3_ENET_GROUP8);
}
}
}
else
{
if ((in8(FPGA_REG0) & FPGA_REG0_ECLS_MASK) == FPGA_REG0_ECLS_VER1)
{
out8(FPGA_REG3, (in8(FPGA_REG3) & ~FPGA_REG3_ENET_MASK1) |
FPGA_REG3_ENET_ENCODE1(SDR0_PFC1_EPS_DECODE(sdr0_pfc1)));
}
else
{
out8(FPGA_REG3, (in8(FPGA_REG3) & ~FPGA_REG3_ENET_MASK2) |
FPGA_REG3_ENET_ENCODE2(SDR0_PFC1_EPS_DECODE(sdr0_pfc1)));
}
}
out8(FPGA_REG4, FPGA_REG4_GPHY_MODE10 |
FPGA_REG4_GPHY_MODE100 | FPGA_REG4_GPHY_MODE1000 |
FPGA_REG4_GPHY_FRC_DPLX | FPGA_REG4_CONNECT_PHYS);
/* reset the gigabyte phy if necessary */
if (SDR0_PFC1_EPS_DECODE(sdr0_pfc1) >= 3)
{
if ((in8(FPGA_REG0) & FPGA_REG0_ECLS_MASK) == FPGA_REG0_ECLS_VER1)
{
out8(FPGA_REG3, in8(FPGA_REG3) & ~FPGA_REG3_GIGABIT_RESET_DISABLE);
udelay(10000);
out8(FPGA_REG3, in8(FPGA_REG3) | FPGA_REG3_GIGABIT_RESET_DISABLE);
}
else
{
out8(FPGA_REG2, in8(FPGA_REG2) & ~FPGA_REG2_GIGABIT_RESET_DISABLE);
udelay(10000);
out8(FPGA_REG2, in8(FPGA_REG2) | FPGA_REG2_GIGABIT_RESET_DISABLE);
}
}
/*
* new Ocotea with Rev. F (pass 3) chips has SMII PHY reset
*/
if ((in8(FPGA_REG0) & FPGA_REG0_ECLS_MASK) == FPGA_REG0_ECLS_VER2) {
out8(FPGA_REG2, in8(FPGA_REG2) & ~FPGA_REG2_SMII_RESET_DISABLE);
udelay(10000);
out8(FPGA_REG2, in8(FPGA_REG2) | FPGA_REG2_SMII_RESET_DISABLE);
}
/* Turn off the LED's */
out8(FPGA_REG3, (in8(FPGA_REG3) & ~FPGA_REG3_STAT_MASK) |
FPGA_REG3_STAT_LED8_DISAB | FPGA_REG3_STAT_LED4_DISAB |
FPGA_REG3_STAT_LED2_DISAB | FPGA_REG3_STAT_LED1_DISAB);
return;
}
/*
* misc_init_r.
*/
int misc_init_r(void)
{
unsigned long usb2d0cr = 0;
unsigned long usb2phy0cr, usb2h0cr = 0;
unsigned long sdr0_pfc1;
#ifdef CONFIG_ENV_IS_IN_FLASH
/* Monitor protection ON by default */
(void)flash_protect(FLAG_PROTECT_SET,
-CONFIG_SYS_MONITOR_LEN,
0xffffffff,
&flash_info[0]);
#ifdef CONFIG_ENV_ADDR_REDUND
/* Env protection ON by default */
(void)flash_protect(FLAG_PROTECT_SET,
CONFIG_ENV_ADDR_REDUND,
CONFIG_ENV_ADDR_REDUND + 2*CONFIG_ENV_SECT_SIZE - 1,
&flash_info[0]);
#endif
#endif
/*
* USB stuff...
*/
/* SDR Setting */
mfsdr(SDR0_PFC1, sdr0_pfc1);
mfsdr(SDR0_USB2D0CR, usb2d0cr);
mfsdr(SDR0_USB2PHY0CR, usb2phy0cr);
mfsdr(SDR0_USB2H0CR, usb2h0cr);
usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_XOCLK_MASK;
usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_XOCLK_EXTERNAL; /*0*/
usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_WDINT_MASK;
usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_WDINT_16BIT_30MHZ; /*1*/
usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DVBUS_MASK;
usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DVBUS_PURDIS; /*0*/
usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DWNSTR_MASK;
usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DWNSTR_HOST; /*1*/
usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_UTMICN_MASK;
usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_UTMICN_HOST; /*1*/
/* An 8-bit/60MHz interface is the only possible alternative
* when connecting the Device to the PHY
*/
usb2h0cr = usb2h0cr &~SDR0_USB2H0CR_WDINT_MASK;
usb2h0cr = usb2h0cr | SDR0_USB2H0CR_WDINT_16BIT_30MHZ; /*1*/
/* To enable the USB 2.0 Device function through the UTMI interface */
usb2d0cr = usb2d0cr &~SDR0_USB2D0CR_USB2DEV_EBC_SEL_MASK;
usb2d0cr = usb2d0cr | SDR0_USB2D0CR_USB2DEV_SELECTION; /*1*/
sdr0_pfc1 = sdr0_pfc1 &~SDR0_PFC1_UES_MASK;
sdr0_pfc1 = sdr0_pfc1 | SDR0_PFC1_UES_USB2D_SEL; /*0*/
mtsdr(SDR0_PFC1, sdr0_pfc1);
mtsdr(SDR0_USB2D0CR, usb2d0cr);
mtsdr(SDR0_USB2PHY0CR, usb2phy0cr);
mtsdr(SDR0_USB2H0CR, usb2h0cr);
/*clear resets*/
udelay(1000);
mtsdr(SDR0_SRST1, 0x00000000);
udelay(1000);
mtsdr(SDR0_SRST0, 0x00000000);
printf("USB: Host(int phy) Device(ext phy)\n");
common_misc_init_r();
set_params_for_sw_install( sys_install_requested(), "hcu5" );
/* We cannot easily enable trace before, as there are other
* routines messing around with sdr0_pfc1. And I do not need it.
*/
if (mfspr(SPRN_DBCR0) & 0x80000000) {
/* External debugger alive
* enable trace facilty for Lauterbach
* CCR0[DTB]=0 Enable broadcast of trace information
* SDR0_PFC0[TRE] Trace signals are enabled instead of
* GPIO49-63
*/
mtspr(SPRN_CCR0, mfspr(SPRN_CCR0) &~ (CCR0_DTB));
mtsdr(SDR0_PFC0, sdr0_pfc1 | SDR0_PFC0_TRE_ENABLE);
}
return 0;
}
int board_early_init_f (void)
{
/*----------------------------------------------------------------------------+
| Define Boot devices
+----------------------------------------------------------------------------*/
#define BOOT_FROM_SMALL_FLASH 0x00
#define BOOT_FROM_LARGE_FLASH_OR_SRAM 0x01
#define BOOT_FROM_PCI 0x02
#define BOOT_DEVICE_UNKNOWN 0x03
/*----------------------------------------------------------------------------+
| EBC Devices Characteristics
| Peripheral Bank Access Parameters - EBC_BxAP
| Peripheral Bank Configuration Register - EBC_BxCR
+----------------------------------------------------------------------------*/
/*
* Small Flash and FRAM
* BU Value
* BxAP : 0x03800000 - 0 00000111 0 00 00 00 00 00 000 0 0 0 0 00000
* B0CR : 0xff098000 - BAS = ff0 - 100 11 00 0000000000000
* B2CR : 0xe7098000 - BAS = e70 - 100 11 00 0000000000000
*/
#define EBC_BXAP_SMALL_FLASH EBC_BXAP_BME_DISABLED | \
EBC_BXAP_TWT_ENCODE(7) | \
EBC_BXAP_BCE_DISABLE | \
EBC_BXAP_BCT_2TRANS | \
EBC_BXAP_CSN_ENCODE(0) | \
EBC_BXAP_OEN_ENCODE(0) | \
EBC_BXAP_WBN_ENCODE(0) | \
EBC_BXAP_WBF_ENCODE(0) | \
EBC_BXAP_TH_ENCODE(0) | \
EBC_BXAP_RE_DISABLED | \
EBC_BXAP_SOR_DELAYED | \
EBC_BXAP_BEM_WRITEONLY | \
EBC_BXAP_PEN_DISABLED
#define EBC_BXCR_SMALL_FLASH_CS0 EBC_BXCR_BAS_ENCODE(0xFF000000) | \
EBC_BXCR_BS_16MB | \
EBC_BXCR_BU_RW | \
EBC_BXCR_BW_8BIT
#define EBC_BXCR_SMALL_FLASH_CS2 EBC_BXCR_BAS_ENCODE(0xe7000000) | \
EBC_BXCR_BS_16MB | \
EBC_BXCR_BU_RW | \
EBC_BXCR_BW_8BIT
/*
* Large Flash and SRAM
* BU Value
* BxAP : 0x048ff240 - 0 00000111 0 00 00 00 00 00 000 0 0 0 0 00000
* B0CR : 0xff09a000 - BAS = ff0 - 100 11 01 0000000000000
* B2CR : 0xe709a000 - BAS = e70 - 100 11 01 0000000000000
*/
#define EBC_BXAP_LARGE_FLASH EBC_BXAP_BME_DISABLED | \
EBC_BXAP_TWT_ENCODE(7) | \
EBC_BXAP_BCE_DISABLE | \
EBC_BXAP_BCT_2TRANS | \
EBC_BXAP_CSN_ENCODE(0) | \
EBC_BXAP_OEN_ENCODE(0) | \
EBC_BXAP_WBN_ENCODE(0) | \
EBC_BXAP_WBF_ENCODE(0) | \
EBC_BXAP_TH_ENCODE(0) | \
EBC_BXAP_RE_DISABLED | \
EBC_BXAP_SOR_DELAYED | \
EBC_BXAP_BEM_WRITEONLY | \
EBC_BXAP_PEN_DISABLED
#define EBC_BXCR_LARGE_FLASH_CS0 EBC_BXCR_BAS_ENCODE(0xFF000000) | \
EBC_BXCR_BS_16MB | \
EBC_BXCR_BU_RW | \
EBC_BXCR_BW_16BIT
#define EBC_BXCR_LARGE_FLASH_CS2 EBC_BXCR_BAS_ENCODE(0xE7000000) | \
EBC_BXCR_BS_16MB | \
EBC_BXCR_BU_RW | \
EBC_BXCR_BW_16BIT
/*
* FPGA
* BU value :
* B1AP = 0x05895240 - 0 00001011 0 00 10 01 01 01 001 0 0 1 0 00000
* B1CR = 0xe201a000 - BAS = e20 - 000 11 01 00000000000000
*/
#define EBC_BXAP_FPGA EBC_BXAP_BME_DISABLED | \
EBC_BXAP_TWT_ENCODE(11) | \
EBC_BXAP_BCE_DISABLE | \
EBC_BXAP_BCT_2TRANS | \
EBC_BXAP_CSN_ENCODE(10) | \
EBC_BXAP_OEN_ENCODE(1) | \
EBC_BXAP_WBN_ENCODE(1) | \
EBC_BXAP_WBF_ENCODE(1) | \
EBC_BXAP_TH_ENCODE(1) | \
EBC_BXAP_RE_DISABLED | \
EBC_BXAP_SOR_DELAYED | \
EBC_BXAP_BEM_RW | \
EBC_BXAP_PEN_DISABLED
#define EBC_BXCR_FPGA_CS1 EBC_BXCR_BAS_ENCODE(0xe2000000) | \
EBC_BXCR_BS_1MB | \
EBC_BXCR_BU_RW | \
EBC_BXCR_BW_16BIT
unsigned long mfr;
/*
* Define Variables for EBC initialization depending on BOOTSTRAP option
*/
unsigned long sdr0_pinstp, sdr0_sdstp1 ;
unsigned long bootstrap_settings, ebc_data_width, boot_selection;
int computed_boot_device = BOOT_DEVICE_UNKNOWN;
/*-------------------------------------------------------------------+
| Initialize EBC CONFIG -
| Keep the Default value, but the bit PDT which has to be set to 1 ?TBC
| default value :
| 0x07C00000 - 0 0 000 1 1 1 1 1 0000 0 00000 000000000000
|
+-------------------------------------------------------------------*/
mtebc(EBC0_CFG, EBC_CFG_LE_UNLOCK |
EBC_CFG_PTD_ENABLE |
EBC_CFG_RTC_16PERCLK |
EBC_CFG_ATC_PREVIOUS |
EBC_CFG_DTC_PREVIOUS |
EBC_CFG_CTC_PREVIOUS |
EBC_CFG_OEO_PREVIOUS |
EBC_CFG_EMC_DEFAULT |
EBC_CFG_PME_DISABLE |
EBC_CFG_PR_16);
/*-------------------------------------------------------------------+
|
| PART 1 : Initialize EBC Bank 1
| ==============================
| Bank1 is always associated to the EPLD.
| It has to be initialized prior to other banks settings computation
| since some board registers values may be needed to determine the
| boot type
|
+-------------------------------------------------------------------*/
mtebc(PB1AP, EBC_BXAP_FPGA);
mtebc(PB1CR, EBC_BXCR_FPGA_CS1);
/*-------------------------------------------------------------------+
|
| PART 2 : Determine which boot device was selected
| =================================================
|
| Read Pin Strap Register in PPC440SPe
| Result can either be :
| - Boot strap = boot from EBC 8bits => Small Flash
| - Boot strap = boot from PCI
| - Boot strap = IIC
| In case of boot from IIC, read Serial Device Strap Register1
|
| Result can either be :
| - Boot from EBC - EBC Bus Width = 8bits => Small Flash
| - Boot from EBC - EBC Bus Width = 16bits => Large Flash or SRAM
| - Boot from PCI
|
+-------------------------------------------------------------------*/
/* Read Pin Strap Register in PPC440SP */
mfsdr(SDR0_PINSTP, sdr0_pinstp);
bootstrap_settings = sdr0_pinstp & SDR0_PINSTP_BOOTSTRAP_MASK;
switch (bootstrap_settings) {
case SDR0_PINSTP_BOOTSTRAP_SETTINGS0:
/*
* Strapping Option A
* Boot from EBC - 8 bits , Small Flash
*/
computed_boot_device = BOOT_FROM_SMALL_FLASH;
break;
case SDR0_PINSTP_BOOTSTRAP_SETTINGS1:
/*
* Strappping Option B
* Boot from PCI
*/
computed_boot_device = BOOT_FROM_PCI;
break;
case SDR0_PINSTP_BOOTSTRAP_IIC_50_EN:
case SDR0_PINSTP_BOOTSTRAP_IIC_54_EN:
/*
* Strapping Option C or D
* Boot Settings in IIC EEprom address 0x50 or 0x54
* Read Serial Device Strap Register1 in PPC440SPe
*/
mfsdr(SDR0_SDSTP1, sdr0_sdstp1);
boot_selection = sdr0_sdstp1 & SDR0_SDSTP1_ERPN_MASK;
ebc_data_width = sdr0_sdstp1 & SDR0_SDSTP1_EBCW_MASK;
switch (boot_selection) {
case SDR0_SDSTP1_ERPN_EBC:
switch (ebc_data_width) {
case SDR0_SDSTP1_EBCW_16_BITS:
computed_boot_device =
BOOT_FROM_LARGE_FLASH_OR_SRAM;
break;
case SDR0_SDSTP1_EBCW_8_BITS :
computed_boot_device = BOOT_FROM_SMALL_FLASH;
break;
}
break;
case SDR0_SDSTP1_ERPN_PCI:
computed_boot_device = BOOT_FROM_PCI;
break;
default:
/* should not occure */
computed_boot_device = BOOT_DEVICE_UNKNOWN;
}
break;
default:
/* should not be */
computed_boot_device = BOOT_DEVICE_UNKNOWN;
break;
}
/*-------------------------------------------------------------------+
|
| PART 3 : Compute EBC settings depending on selected boot device
| ====== ======================================================
|
| Resulting EBC init will be among following configurations :
|
| - Boot from EBC 8bits => boot from Small Flash selected
| EBC-CS0 = Small Flash
| EBC-CS2 = Large Flash and SRAM
|
| - Boot from EBC 16bits => boot from Large Flash or SRAM
| EBC-CS0 = Large Flash or SRAM
| EBC-CS2 = Small Flash
|
| - Boot from PCI
| EBC-CS0 = not initialized to avoid address contention
| EBC-CS2 = same as boot from Small Flash selected
|
+-------------------------------------------------------------------*/
unsigned long ebc0_cs0_bxap_value = 0, ebc0_cs0_bxcr_value = 0;
unsigned long ebc0_cs2_bxap_value = 0, ebc0_cs2_bxcr_value = 0;
switch (computed_boot_device) {
/*-------------------------------------------------------------------*/
case BOOT_FROM_PCI:
/*-------------------------------------------------------------------*/
/*
* By Default CS2 is affected to LARGE Flash
* do not initialize SMALL FLASH to avoid address contention
* Large Flash
*/
ebc0_cs2_bxap_value = EBC_BXAP_LARGE_FLASH;
ebc0_cs2_bxcr_value = EBC_BXCR_LARGE_FLASH_CS2;
break;
/*-------------------------------------------------------------------*/
case BOOT_FROM_SMALL_FLASH:
/*-------------------------------------------------------------------*/
ebc0_cs0_bxap_value = EBC_BXAP_SMALL_FLASH;
ebc0_cs0_bxcr_value = EBC_BXCR_SMALL_FLASH_CS0;
/*
* Large Flash or SRAM
*/
/* ebc0_cs2_bxap_value = EBC_BXAP_LARGE_FLASH; */
ebc0_cs2_bxap_value = 0x048ff240;
ebc0_cs2_bxcr_value = EBC_BXCR_LARGE_FLASH_CS2;
break;
/*-------------------------------------------------------------------*/
case BOOT_FROM_LARGE_FLASH_OR_SRAM:
/*-------------------------------------------------------------------*/
ebc0_cs0_bxap_value = EBC_BXAP_LARGE_FLASH;
ebc0_cs0_bxcr_value = EBC_BXCR_LARGE_FLASH_CS0;
/* Small flash */
ebc0_cs2_bxap_value = EBC_BXAP_SMALL_FLASH;
ebc0_cs2_bxcr_value = EBC_BXCR_SMALL_FLASH_CS2;
break;
/*-------------------------------------------------------------------*/
default:
/*-------------------------------------------------------------------*/
/* BOOT_DEVICE_UNKNOWN */
break;
}
mtebc(PB0AP, ebc0_cs0_bxap_value);
mtebc(PB0CR, ebc0_cs0_bxcr_value);
mtebc(PB2AP, ebc0_cs2_bxap_value);
mtebc(PB2CR, ebc0_cs2_bxcr_value);
/*--------------------------------------------------------------------+
| Interrupt controller setup for the AMCC 440SPe Evaluation board.
+--------------------------------------------------------------------+
+---------------------------------------------------------------------+
|Interrupt| Source | Pol. | Sensi.| Crit. |
+---------+-----------------------------------+-------+-------+-------+
| IRQ 00 | UART0 | High | Level | Non |
| IRQ 01 | UART1 | High | Level | Non |
| IRQ 02 | IIC0 | High | Level | Non |
| IRQ 03 | IIC1 | High | Level | Non |
| IRQ 04 | PCI0X0 MSG IN | High | Level | Non |
| IRQ 05 | PCI0X0 CMD Write | High | Level | Non |
| IRQ 06 | PCI0X0 Power Mgt | High | Level | Non |
| IRQ 07 | PCI0X0 VPD Access | Rising| Edge | Non |
| IRQ 08 | PCI0X0 MSI level 0 | High | Lvl/ed| Non |
| IRQ 09 | External IRQ 15 - (PCI-Express) | pgm H | Pgm | Non |
| IRQ 10 | UIC2 Non-critical Int. | NA | NA | Non |
| IRQ 11 | UIC2 Critical Interrupt | NA | NA | Crit |
| IRQ 12 | PCI Express MSI Level 0 | Rising| Edge | Non |
| IRQ 13 | PCI Express MSI Level 1 | Rising| Edge | Non |
| IRQ 14 | PCI Express MSI Level 2 | Rising| Edge | Non |
| IRQ 15 | PCI Express MSI Level 3 | Rising| Edge | Non |
| IRQ 16 | UIC3 Non-critical Int. | NA | NA | Non |
| IRQ 17 | UIC3 Critical Interrupt | NA | NA | Crit |
| IRQ 18 | External IRQ 14 - (PCI-Express) | Pgm | Pgm | Non |
| IRQ 19 | DMA Channel 0 FIFO Full | High | Level | Non |
| IRQ 20 | DMA Channel 0 Stat FIFO | High | Level | Non |
| IRQ 21 | DMA Channel 1 FIFO Full | High | Level | Non |
| IRQ 22 | DMA Channel 1 Stat FIFO | High | Level | Non |
| IRQ 23 | I2O Inbound Doorbell | High | Level | Non |
| IRQ 24 | Inbound Post List FIFO Not Empt | High | Level | Non |
| IRQ 25 | I2O Region 0 LL PLB Write | High | Level | Non |
| IRQ 26 | I2O Region 1 LL PLB Write | High | Level | Non |
| IRQ 27 | I2O Region 0 HB PLB Write | High | Level | Non |
| IRQ 28 | I2O Region 1 HB PLB Write | High | Level | Non |
| IRQ 29 | GPT Down Count Timer | Rising| Edge | Non |
| IRQ 30 | UIC1 Non-critical Int. | NA | NA | Non |
| IRQ 31 | UIC1 Critical Interrupt | NA | NA | Crit. |
|----------------------------------------------------------------------
| IRQ 32 | Ext. IRQ 13 - (PCI-Express) |pgm (H)|pgm/Lvl| Non |
| IRQ 33 | MAL Serr | High | Level | Non |
| IRQ 34 | MAL Txde | High | Level | Non |
| IRQ 35 | MAL Rxde | High | Level | Non |
| IRQ 36 | DMC CE or DMC UE | High | Level | Non |
| IRQ 37 | EBC or UART2 | High |Lvl Edg| Non |
| IRQ 38 | MAL TX EOB | High | Level | Non |
| IRQ 39 | MAL RX EOB | High | Level | Non |
| IRQ 40 | PCIX0 MSI Level 1 | High |Lvl Edg| Non |
| IRQ 41 | PCIX0 MSI level 2 | High |Lvl Edg| Non |
| IRQ 42 | PCIX0 MSI level 3 | High |Lvl Edg| Non |
| IRQ 43 | L2 Cache | Risin | Edge | Non |
| IRQ 44 | GPT Compare Timer 0 | Risin | Edge | Non |
| IRQ 45 | GPT Compare Timer 1 | Risin | Edge | Non |
| IRQ 46 | GPT Compare Timer 2 | Risin | Edge | Non |
| IRQ 47 | GPT Compare Timer 3 | Risin | Edge | Non |
| IRQ 48 | GPT Compare Timer 4 | Risin | Edge | Non |
| IRQ 49 | Ext. IRQ 12 - PCI-X |pgm/Fal|pgm/Lvl| Non |
| IRQ 50 | Ext. IRQ 11 - |pgm (H)|pgm/Lvl| Non |
| IRQ 51 | Ext. IRQ 10 - |pgm (H)|pgm/Lvl| Non |
| IRQ 52 | Ext. IRQ 9 |pgm (H)|pgm/Lvl| Non |
| IRQ 53 | Ext. IRQ 8 |pgm (H)|pgm/Lvl| Non |
| IRQ 54 | DMA Error | High | Level | Non |
| IRQ 55 | DMA I2O Error | High | Level | Non |
| IRQ 56 | Serial ROM | High | Level | Non |
| IRQ 57 | PCIX0 Error | High | Edge | Non |
| IRQ 58 | Ext. IRQ 7- |pgm (H)|pgm/Lvl| Non |
| IRQ 59 | Ext. IRQ 6- |pgm (H)|pgm/Lvl| Non |
| IRQ 60 | EMAC0 Interrupt | High | Level | Non |
| IRQ 61 | EMAC0 Wake-up | High | Level | Non |
| IRQ 62 | Reserved | High | Level | Non |
| IRQ 63 | XOR | High | Level | Non |
|----------------------------------------------------------------------
| IRQ 64 | PE0 AL | High | Level | Non |
| IRQ 65 | PE0 VPD Access | Risin | Edge | Non |
| IRQ 66 | PE0 Hot Reset Request | Risin | Edge | Non |
| IRQ 67 | PE0 Hot Reset Request | Falli | Edge | Non |
| IRQ 68 | PE0 TCR | High | Level | Non |
| IRQ 69 | PE0 BusMaster VCO | Falli | Edge | Non |
| IRQ 70 | PE0 DCR Error | High | Level | Non |
| IRQ 71 | Reserved | N/A | N/A | Non |
| IRQ 72 | PE1 AL | High | Level | Non |
| IRQ 73 | PE1 VPD Access | Risin | Edge | Non |
| IRQ 74 | PE1 Hot Reset Request | Risin | Edge | Non |
| IRQ 75 | PE1 Hot Reset Request | Falli | Edge | Non |
| IRQ 76 | PE1 TCR | High | Level | Non |
| IRQ 77 | PE1 BusMaster VCO | Falli | Edge | Non |
| IRQ 78 | PE1 DCR Error | High | Level | Non |
| IRQ 79 | Reserved | N/A | N/A | Non |
| IRQ 80 | PE2 AL | High | Level | Non |
| IRQ 81 | PE2 VPD Access | Risin | Edge | Non |
| IRQ 82 | PE2 Hot Reset Request | Risin | Edge | Non |
| IRQ 83 | PE2 Hot Reset Request | Falli | Edge | Non |
| IRQ 84 | PE2 TCR | High | Level | Non |
| IRQ 85 | PE2 BusMaster VCO | Falli | Edge | Non |
| IRQ 86 | PE2 DCR Error | High | Level | Non |
| IRQ 87 | Reserved | N/A | N/A | Non |
| IRQ 88 | External IRQ(5) | Progr | Progr | Non |
| IRQ 89 | External IRQ 4 - Ethernet | Progr | Progr | Non |
| IRQ 90 | External IRQ 3 - PCI-X | Progr | Progr | Non |
| IRQ 91 | External IRQ 2 - PCI-X | Progr | Progr | Non |
| IRQ 92 | External IRQ 1 - PCI-X | Progr | Progr | Non |
| IRQ 93 | External IRQ 0 - PCI-X | Progr | Progr | Non |
| IRQ 94 | Reserved | N/A | N/A | Non |
| IRQ 95 | Reserved | N/A | N/A | Non |
|---------------------------------------------------------------------
| IRQ 96 | PE0 INTA | High | Level | Non |
| IRQ 97 | PE0 INTB | High | Level | Non |
| IRQ 98 | PE0 INTC | High | Level | Non |
| IRQ 99 | PE0 INTD | High | Level | Non |
| IRQ 100 | PE1 INTA | High | Level | Non |
| IRQ 101 | PE1 INTB | High | Level | Non |
| IRQ 102 | PE1 INTC | High | Level | Non |
| IRQ 103 | PE1 INTD | High | Level | Non |
| IRQ 104 | PE2 INTA | High | Level | Non |
| IRQ 105 | PE2 INTB | High | Level | Non |
| IRQ 106 | PE2 INTC | High | Level | Non |
| IRQ 107 | PE2 INTD | Risin | Edge | Non |
| IRQ 108 | PCI Express MSI Level 4 | Risin | Edge | Non |
| IRQ 109 | PCI Express MSI Level 5 | Risin | Edge | Non |
| IRQ 110 | PCI Express MSI Level 6 | Risin | Edge | Non |
| IRQ 111 | PCI Express MSI Level 7 | Risin | Edge | Non |
| IRQ 116 | PCI Express MSI Level 12 | Risin | Edge | Non |
| IRQ 112 | PCI Express MSI Level 8 | Risin | Edge | Non |
| IRQ 113 | PCI Express MSI Level 9 | Risin | Edge | Non |
| IRQ 114 | PCI Express MSI Level 10 | Risin | Edge | Non |
| IRQ 115 | PCI Express MSI Level 11 | Risin | Edge | Non |
| IRQ 117 | PCI Express MSI Level 13 | Risin | Edge | Non |
| IRQ 118 | PCI Express MSI Level 14 | Risin | Edge | Non |
| IRQ 119 | PCI Express MSI Level 15 | Risin | Edge | Non |
| IRQ 120 | PCI Express MSI Level 16 | Risin | Edge | Non |
| IRQ 121 | PCI Express MSI Level 17 | Risin | Edge | Non |
| IRQ 122 | PCI Express MSI Level 18 | Risin | Edge | Non |
| IRQ 123 | PCI Express MSI Level 19 | Risin | Edge | Non |
| IRQ 124 | PCI Express MSI Level 20 | Risin | Edge | Non |
| IRQ 125 | PCI Express MSI Level 21 | Risin | Edge | Non |
| IRQ 126 | PCI Express MSI Level 22 | Risin | Edge | Non |
| IRQ 127 | PCI Express MSI Level 23 | Risin | Edge | Non |
+---------+-----------------------------------+-------+-------+------*/
/*--------------------------------------------------------------------+
| Put UICs in PowerPC440SPemode.
| Initialise UIC registers. Clear all interrupts. Disable all
| interrupts.
| Set critical interrupt values. Set interrupt polarities. Set
| interrupt trigger levels. Make bit 0 High priority. Clear all
| interrupts again.
+-------------------------------------------------------------------*/
mtdcr (UIC3SR, 0xffffffff); /* Clear all interrupts */
mtdcr (UIC3ER, 0x00000000); /* disable all interrupts */
mtdcr (UIC3CR, 0x00000000); /* Set Critical / Non Critical
* interrupts */
mtdcr (UIC3PR, 0xffffffff); /* Set Interrupt Polarities */
mtdcr (UIC3TR, 0x001fffff); /* Set Interrupt Trigger Levels */
mtdcr (UIC3VR, 0x00000001); /* Set Vect base=0,INT31 Highest
* priority */
mtdcr (UIC3SR, 0x00000000); /* clear all interrupts */
mtdcr (UIC3SR, 0xffffffff); /* clear all interrupts */
mtdcr (UIC2SR, 0xffffffff); /* Clear all interrupts */
mtdcr (UIC2ER, 0x00000000); /* disable all interrupts */
mtdcr (UIC2CR, 0x00000000); /* Set Critical / Non Critical
* interrupts */
mtdcr (UIC2PR, 0xebebebff); /* Set Interrupt Polarities */
mtdcr (UIC2TR, 0x74747400); /* Set Interrupt Trigger Levels */
mtdcr (UIC2VR, 0x00000001); /* Set Vect base=0,INT31 Highest
* priority */
mtdcr (UIC2SR, 0x00000000); /* clear all interrupts */
mtdcr (UIC2SR, 0xffffffff); /* clear all interrupts */
mtdcr (UIC1SR, 0xffffffff); /* Clear all interrupts */
mtdcr (UIC1ER, 0x00000000); /* disable all interrupts */
mtdcr (UIC1CR, 0x00000000); /* Set Critical / Non Critical
* interrupts */
mtdcr (UIC1PR, 0xffffffff); /* Set Interrupt Polarities */
mtdcr (UIC1TR, 0x001f8040); /* Set Interrupt Trigger Levels */
mtdcr (UIC1VR, 0x00000001); /* Set Vect base=0,INT31 Highest
* priority */
mtdcr (UIC1SR, 0x00000000); /* clear all interrupts */
mtdcr (UIC1SR, 0xffffffff); /* clear all interrupts */
mtdcr (UIC0SR, 0xffffffff); /* Clear all interrupts */
mtdcr (UIC0ER, 0x00000000); /* disable all interrupts excepted
* cascade to be checked */
mtdcr (UIC0CR, 0x00104001); /* Set Critical / Non Critical
* interrupts */
mtdcr (UIC0PR, 0xffffffff); /* Set Interrupt Polarities */
mtdcr (UIC0TR, 0x010f0004); /* Set Interrupt Trigger Levels */
mtdcr (UIC0VR, 0x00000001); /* Set Vect base=0,INT31 Highest
* priority */
mtdcr (UIC0SR, 0x00000000); /* clear all interrupts */
mtdcr (UIC0SR, 0xffffffff); /* clear all interrupts */
mfsdr(SDR0_MFR, mfr);
mfr |= SDR0_MFR_FIXD; /* Workaround for PCI/DMA */
mtsdr(SDR0_MFR, mfr);
fpga_init();
return 0;
}
