int main ()
{
uint8_t ds;
nrk_setup_ports ();
nrk_setup_uart (UART_BAUDRATE_115K2);
ds=nrk_eeprom_read_byte(EEPROM_SLEEP_STATE_ADDR);
if(ds==1) deep_sleep_button();
nrk_init ();
nrk_led_clr (0);
nrk_led_clr (1);
nrk_led_clr (2);
nrk_led_clr (3);
nrk_time_set (0, 0);
tdma_set_error_callback(&tdma_error);
tdma_task_config();
nrk_register_drivers();
nrk_create_taskset ();
nrk_start ();
return 0;
}
int main ()
{
uint16_t div;
nrk_int_disable();
// Configure relay port directions
DDRE |= 0x10;
socket_0_enable();
// Configure led port directions
DDRE |= 0x0c;
DDRD |= 0x00;
PORTD |= 0xff;
DDRF = 0;
socket_0_active=nrk_eeprom_read_byte(EEPROM_STATE_ADDR);
// turn outlet on if active or throttled for testing
if(socket_0_active==1 || socket_0_active==2)
{
socket_0_enable();
plug_led_green_set();
} else
{
socket_0_disable();
plug_led_green_clr();
}
// If PUD value set, then we expect it wasn't a clean reboot (unexpected restart).
// Try to force a proper watchdog reboot
if((MCUCR&0x10)!=0 )
{
//nrk_watchdog_enable();
nrk_int_disable();
MCUSR &= ~(1<<WDRF);
WDTCSR |= (1<<WDCE) | (1<<WDE);
WDTCSR = (1<<WDE) | (1<<WDP2) | (1<<WDP0);
// Disable interrupts to stop pending timers etc
while(1);
}
nrk_setup_uart (UART_BAUDRATE_115K2);
MCUCR |= BM(PUD);
nrk_init ();
nrk_time_set (0, 0);
tdma_set_error_callback(&tdma_error);
tdma_task_config();
nrk_create_taskset ();
nrk_start ();
return 0;
}
int main ()
{
uint16_t div;
// Configure relay port directions
DDRE |= 0x10;
socket_0_enable();
// Configure led port directions
DDRE |= 0x0c;
DDRD |= 0x00;
PORTD |= 0xff;
DDRF = 0;
socket_0_active=nrk_eeprom_read_byte(EEPROM_STATE_ADDR);
if(socket_0_active==1)
{
socket_0_enable();
plug_led_green_set();
} else
{
socket_0_disable();
plug_led_green_clr();
}
MCUCR |= BM(PUD);
nrk_setup_uart (UART_BAUDRATE_115K2);
nrk_init ();
nrk_time_set (0, 0);
tdma_set_error_callback(&tdma_error);
tdma_task_config();
nrk_create_taskset ();
nrk_start ();
return 0;
}
void tx_task ()
{
uint8_t j, i, val, cnt;
int8_t len;
int8_t v;
nrk_sig_t tx_done_signal;
nrk_sig_mask_t ret;
send_ack=0;
cal_done=0;
printf ("tx_task PID=%d\r\n", nrk_get_pid ());
// Wait until the tx_task starts up bmac
// This should be called by all tasks using bmac that
power_init ();
#ifndef DISABLE_BUTTON
nrk_gpio_direction(NRK_BUTTON,NRK_PIN_INPUT );
nrk_ext_int_configure(NRK_EXT_INT_0, NRK_FALLING_EDGE, &button_handler );
nrk_ext_int_enable(NRK_EXT_INT_0);
#endif
v_center=((uint16_t)nrk_eeprom_read_byte(EEPROM_CAL_V_MSB_ADDR))<<8 | (uint16_t)nrk_eeprom_read_byte(EEPROM_CAL_V_LSB_ADDR);
c_center=((uint16_t)nrk_eeprom_read_byte(EEPROM_CAL_C1_MSB_ADDR))<<8 | (uint16_t)nrk_eeprom_read_byte(EEPROM_CAL_C1_LSB_ADDR);
c2_center=((uint16_t)nrk_eeprom_read_byte(EEPROM_CAL_C2_MSB_ADDR))<<8 | (uint16_t)nrk_eeprom_read_byte(EEPROM_CAL_C2_LSB_ADDR);
if(((PIND & 0x1) == 0) || (v_center==0xffff) || (v_center==0x0) )
{
// Get v_center and c_centers enough to grab calibration values
v_center=512;
c_center=512;
c2_center=512;
power_socket_enable(0);
socket_0_disable();
plug_led_green_clr();
plug_led_red_clr();
for(i=0; i<3; i++ ) {
plug_led_green_set();
nrk_wait_until_next_period();
plug_led_green_clr();
nrk_wait_until_next_period();
}
plug_led_green_clr();
plug_led_red_clr();
for(i=0; i<5; i++ )
nrk_wait_until_next_period();
v_center=(v_p2p_high+v_p2p_low)/2;
c_center=(c_p2p_high+c_p2p_low)/2;
c2_center=(c_p2p_high2+c_p2p_low2)/2;
nrk_eeprom_write_byte(EEPROM_CAL_V_MSB_ADDR, (uint8_t)(v_center>>8));
nrk_eeprom_write_byte(EEPROM_CAL_V_LSB_ADDR, (uint8_t)v_center&0xff);
nrk_eeprom_write_byte(EEPROM_CAL_C1_MSB_ADDR, (uint8_t)(c_center>>8));
nrk_eeprom_write_byte(EEPROM_CAL_C1_LSB_ADDR, (uint8_t)c_center&0xff);
nrk_eeprom_write_byte(EEPROM_CAL_C2_MSB_ADDR, (uint8_t)(c2_center>>8));
nrk_eeprom_write_byte(EEPROM_CAL_C2_LSB_ADDR, (uint8_t)c2_center&0xff);
nrk_eeprom_write_byte(EEPROM_ENERGY1_0_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY1_1_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY1_2_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY1_3_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY1_4_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY1_5_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY1_6_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY1_7_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY2_0_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY2_1_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY2_2_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY2_3_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY2_4_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY2_5_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY2_6_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY2_7_ADDR, 0);
//plug_led_green_set();
//socket_0_enable();
//power_socket_enable(0);
// Set default power threshold
set_power_thresh(DEFAULT_POWER_THRESH);
power_socket_disable(0);
socket_0_disable();
}
nrk_eeprom_write_byte(EEPROM_ENERGY2_3_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY2_4_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY2_5_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY2_6_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY2_7_ADDR, 0);
//plug_led_green_set();
//socket_0_enable();
//power_socket_enable(0);
// Set default power threshold
set_power_thresh(DEFAULT_POWER_THRESH);
power_socket_disable(0);
socket_0_disable();
}
cummulative_energy.byte[0]=nrk_eeprom_read_byte(EEPROM_ENERGY1_0_ADDR);
cummulative_energy.byte[1]=nrk_eeprom_read_byte(EEPROM_ENERGY1_1_ADDR);
cummulative_energy.byte[2]=nrk_eeprom_read_byte(EEPROM_ENERGY1_2_ADDR);
cummulative_energy.byte[3]=nrk_eeprom_read_byte(EEPROM_ENERGY1_3_ADDR);
cummulative_energy.byte[4]=nrk_eeprom_read_byte(EEPROM_ENERGY1_4_ADDR);
cummulative_energy.byte[5]=nrk_eeprom_read_byte(EEPROM_ENERGY1_5_ADDR);
cummulative_energy.byte[6]=nrk_eeprom_read_byte(EEPROM_ENERGY1_6_ADDR);
cummulative_energy.byte[7]=nrk_eeprom_read_byte(EEPROM_ENERGY1_7_ADDR);
cummulative_energy2.byte[0]=nrk_eeprom_read_byte(EEPROM_ENERGY2_0_ADDR);
cummulative_energy2.byte[1]=nrk_eeprom_read_byte(EEPROM_ENERGY2_1_ADDR);
cummulative_energy2.byte[2]=nrk_eeprom_read_byte(EEPROM_ENERGY2_2_ADDR);
cummulative_energy2.byte[3]=nrk_eeprom_read_byte(EEPROM_ENERGY2_3_ADDR);
cummulative_energy2.byte[4]=nrk_eeprom_read_byte(EEPROM_ENERGY2_4_ADDR);
cummulative_energy2.byte[5]=nrk_eeprom_read_byte(EEPROM_ENERGY2_5_ADDR);
cummulative_energy2.byte[6]=nrk_eeprom_read_byte(EEPROM_ENERGY2_6_ADDR);
cummulative_energy2.byte[7]=nrk_eeprom_read_byte(EEPROM_ENERGY2_7_ADDR);
void tx_task ()
{
uint8_t j, i, val, cnt;
int8_t len;
int8_t v;
nrk_sig_t tx_done_signal;
nrk_sig_mask_t ret;
cal_done=0;
printf ("tx_task PID=%d\r\n", nrk_get_pid ());
// Wait until the tx_task starts up bmac
// This should be called by all tasks using bmac that
power_init ();
v_center=((uint16_t)nrk_eeprom_read_byte(EEPROM_CAL_V_MSB_ADDR))<<8 | (uint16_t)nrk_eeprom_read_byte(EEPROM_CAL_V_LSB_ADDR);
c_center=((uint16_t)nrk_eeprom_read_byte(EEPROM_CAL_C1_MSB_ADDR))<<8 | (uint16_t)nrk_eeprom_read_byte(EEPROM_CAL_C1_LSB_ADDR);
c2_center=((uint16_t)nrk_eeprom_read_byte(EEPROM_CAL_C2_MSB_ADDR))<<8 | (uint16_t)nrk_eeprom_read_byte(EEPROM_CAL_C2_LSB_ADDR);
if(((PIND & 0x1) == 0) || (v_center==0xffff) || (v_center==0x0) )
{
// Get v_center and c_centers enough to grab calibration values
v_center=512;
c_center=512;
c2_center=512;
power_socket_enable(0);
socket_0_disable();
plug_led_green_clr();
plug_led_red_clr();
for(i=0; i<3; i++ ) {
plug_led_green_set();
nrk_wait_until_next_period();
plug_led_green_clr();
nrk_wait_until_next_period();
}
plug_led_green_clr();
plug_led_red_clr();
for(i=0; i<5; i++ )
nrk_wait_until_next_period();
v_center=(v_p2p_high+v_p2p_low)/2;
c_center=(c_p2p_high+c_p2p_low)/2;
c2_center=(c_p2p_high2+c_p2p_low2)/2;
nrk_eeprom_write_byte(EEPROM_CAL_V_MSB_ADDR, (uint8_t)(v_center>>8));
nrk_eeprom_write_byte(EEPROM_CAL_V_LSB_ADDR, (uint8_t)v_center&0xff);
nrk_eeprom_write_byte(EEPROM_CAL_C1_MSB_ADDR, (uint8_t)(c_center>>8));
nrk_eeprom_write_byte(EEPROM_CAL_C1_LSB_ADDR, (uint8_t)c_center&0xff);
nrk_eeprom_write_byte(EEPROM_CAL_C2_MSB_ADDR, (uint8_t)(c2_center>>8));
nrk_eeprom_write_byte(EEPROM_CAL_C2_LSB_ADDR, (uint8_t)c2_center&0xff);
nrk_eeprom_write_byte(EEPROM_ENERGY1_0_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY1_1_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY1_2_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY1_3_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY1_4_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY1_5_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY1_6_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY1_7_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY2_0_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY2_1_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY2_2_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY2_3_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY2_4_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY2_5_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY2_6_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY2_7_ADDR, 0);
plug_led_green_set();
socket_0_enable();
power_socket_enable(0);
}
nrk_eeprom_write_byte(EEPROM_ENERGY1_5_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY1_6_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY1_7_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY2_0_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY2_1_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY2_2_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY2_3_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY2_4_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY2_5_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY2_6_ADDR, 0);
nrk_eeprom_write_byte(EEPROM_ENERGY2_7_ADDR, 0);
plug_led_green_set();
socket_0_enable();
power_socket_enable(0);
}
cummulative_energy.byte[0]=nrk_eeprom_read_byte(EEPROM_ENERGY1_0_ADDR);
cummulative_energy.byte[1]=nrk_eeprom_read_byte(EEPROM_ENERGY1_1_ADDR);
cummulative_energy.byte[2]=nrk_eeprom_read_byte(EEPROM_ENERGY1_2_ADDR);
cummulative_energy.byte[3]=nrk_eeprom_read_byte(EEPROM_ENERGY1_3_ADDR);
cummulative_energy.byte[4]=nrk_eeprom_read_byte(EEPROM_ENERGY1_4_ADDR);
cummulative_energy.byte[5]=nrk_eeprom_read_byte(EEPROM_ENERGY1_5_ADDR);
cummulative_energy.byte[6]=nrk_eeprom_read_byte(EEPROM_ENERGY1_6_ADDR);
cummulative_energy.byte[7]=nrk_eeprom_read_byte(EEPROM_ENERGY1_7_ADDR);
cummulative_energy2.byte[0]=nrk_eeprom_read_byte(EEPROM_ENERGY2_0_ADDR);
cummulative_energy2.byte[1]=nrk_eeprom_read_byte(EEPROM_ENERGY2_1_ADDR);
cummulative_energy2.byte[2]=nrk_eeprom_read_byte(EEPROM_ENERGY2_2_ADDR);
cummulative_energy2.byte[3]=nrk_eeprom_read_byte(EEPROM_ENERGY2_3_ADDR);
cummulative_energy2.byte[4]=nrk_eeprom_read_byte(EEPROM_ENERGY2_4_ADDR);
cummulative_energy2.byte[5]=nrk_eeprom_read_byte(EEPROM_ENERGY2_5_ADDR);
cummulative_energy2.byte[6]=nrk_eeprom_read_byte(EEPROM_ENERGY2_6_ADDR);
cummulative_energy2.byte[7]=nrk_eeprom_read_byte(EEPROM_ENERGY2_7_ADDR);
