static int pic32_eth_start(struct udevice *dev)
{
struct eth_pdata *pdata = dev_get_platdata(dev);
struct pic32eth_dev *priv = dev_get_priv(dev);
/* controller */
pic32_ctrl_reset(priv);
/* reset MAC */
pic32_mac_reset(priv);
/* configure PHY */
phy_config(priv->phydev);
/* initialize MAC */
pic32_mac_init(priv, &pdata->enetaddr[0]);
/* init RX descriptor; TX descriptors are handled in xmit */
pic32_rx_desc_init(priv);
/* Start up & update link status of PHY */
phy_startup(priv->phydev);
/* adjust mac with phy link status */
return pic32_mac_adjust_link(priv);
}
void ls2085a_handle_phy_interface_sgmii(int dpmac_id)
{
int lane, slot;
struct mii_dev *bus;
struct ccsr_gur __iomem *gur = (void *)CONFIG_SYS_FSL_GUTS_ADDR;
int serdes1_prtcl = (in_le32(&gur->rcwsr[28]) &
FSL_CHASSIS3_RCWSR28_SRDS1_PRTCL_MASK)
>> FSL_CHASSIS3_RCWSR28_SRDS1_PRTCL_SHIFT;
int serdes2_prtcl = (in_le32(&gur->rcwsr[28]) &
FSL_CHASSIS3_RCWSR28_SRDS2_PRTCL_MASK)
>> FSL_CHASSIS3_RCWSR28_SRDS2_PRTCL_SHIFT;
switch (serdes1_prtcl) {
}
switch (serdes2_prtcl) {
case 0x07:
case 0x08:
case 0x49:
lane = serdes_get_first_lane(FSL_SRDS_2, SGMII9 +
(dpmac_id - 9));
slot = lane_to_slot_fsm2[lane];
switch (++slot) {
case 1:
break;
case 3:
break;
case 4:
/* Slot housing a SGMII riser card? */
wriop_set_phy_address(dpmac_id,
riser_phy_addr[dpmac_id - 9]);
dpmac_info[dpmac_id].board_mux = EMI1_SLOT4;
bus = mii_dev_for_muxval(EMI1_SLOT4);
wriop_set_mdio(dpmac_id, bus);
dpmac_info[dpmac_id].phydev = phy_connect(
dpmac_info[dpmac_id].bus,
dpmac_info[dpmac_id].phy_addr,
NULL,
dpmac_info[dpmac_id].enet_if);
phy_config(dpmac_info[dpmac_id].phydev);
break;
case 5:
break;
case 6:
/* Slot housing a SGMII riser card? */
wriop_set_phy_address(dpmac_id,
riser_phy_addr[dpmac_id - 13]);
dpmac_info[dpmac_id].board_mux = EMI1_SLOT6;
bus = mii_dev_for_muxval(EMI1_SLOT6);
wriop_set_mdio(dpmac_id, bus);
break;
}
break;
default:
printf("qds: WRIOP: Unsupported SerDes Protocol 0x%02x\n",
serdes2_prtcl);
break;
}
}
/*
* This function initializes the EMAC hardware.
*/
int keystone2_emac_initialize(struct eth_priv_t *eth_priv)
{
int res;
struct eth_device *dev;
struct phy_device *phy_dev;
dev = malloc(sizeof(struct eth_device));
if (dev == NULL)
return -1;
memset(dev, 0, sizeof(struct eth_device));
strcpy(dev->name, eth_priv->int_name);
dev->priv = eth_priv;
keystone2_eth_read_mac_addr(dev);
dev->iobase = 0;
dev->init = keystone2_eth_open;
dev->halt = keystone2_eth_close;
dev->send = keystone2_eth_send_packet;
dev->recv = keystone2_eth_rcv_packet;
#ifdef CONFIG_MCAST_TFTP
dev->mcast = keystone2_eth_bcast_addr;
#endif
eth_register(dev);
/* Register MDIO bus if it's not registered yet */
if (!mdio_bus) {
mdio_bus = mdio_alloc();
mdio_bus->read = keystone2_mdio_read;
mdio_bus->write = keystone2_mdio_write;
mdio_bus->reset = keystone2_mdio_reset;
mdio_bus->priv = (void *)EMAC_MDIO_BASE_ADDR;
sprintf(mdio_bus->name, "ethernet-mdio");
res = mdio_register(mdio_bus);
if (res)
return res;
}
#ifndef CONFIG_SOC_K2G
keystone2_net_serdes_setup();
#endif
/* Create phy device and bind it with driver */
#ifdef CONFIG_KSNET_MDIO_PHY_CONFIG_ENABLE
phy_dev = phy_connect(mdio_bus, eth_priv->phy_addr,
dev, eth_priv->phy_if);
phy_config(phy_dev);
#else
phy_dev = phy_find_by_mask(mdio_bus, 1 << eth_priv->phy_addr,
eth_priv->phy_if);
phy_dev->dev = dev;
#endif
eth_priv->phy_dev = phy_dev;
return 0;
}
/* Discover which PHY is attached to the device, and configure it
* properly. If the PHY is not recognized, then return 0
* (failure). Otherwise, return 1
*/
static int init_phy(struct eth_device *dev)
{
struct tsec_private *priv = (struct tsec_private *)dev->priv;
struct phy_device *phydev;
tsec_t *regs = priv->regs;
u32 supported = (SUPPORTED_10baseT_Half |
SUPPORTED_10baseT_Full |
SUPPORTED_100baseT_Half |
SUPPORTED_100baseT_Full);
if (priv->flags & TSEC_GIGABIT)
supported |= SUPPORTED_1000baseT_Full;
/* Assign a Physical address to the TBI */
out_be32(®s->tbipa, CONFIG_SYS_TBIPA_VALUE);
priv->interface = tsec_get_interface(priv);
if (priv->interface == PHY_INTERFACE_MODE_SGMII)
tsec_configure_serdes(priv);
phydev = phy_connect(priv->bus, priv->phyaddr, dev, priv->interface);
phydev->supported &= supported;
phydev->advertising = phydev->supported;
priv->phydev = phydev;
phy_config(phydev);
return 1;
}
static int bcm_sf2_eth_init(struct eth_device *dev)
{
struct eth_info *eth = (struct eth_info *)(dev->priv);
struct eth_dma *dma = &(eth->dma);
struct phy_device *phydev;
int rc = 0;
int i;
rc = eth->mac_init(dev);
if (rc) {
error("%s: Couldn't cofigure MAC!\n", __func__);
return rc;
}
/* disable DMA */
dma->disable_dma(dma, MAC_DMA_RX);
dma->disable_dma(dma, MAC_DMA_TX);
eth->port_num = 0;
debug("Connecting PHY 0...\n");
phydev = phy_connect(miiphy_get_dev_by_name(dev->name),
0, dev, eth->phy_interface);
if (phydev != NULL) {
eth->port[0] = phydev;
eth->port_num += 1;
} else {
debug("No PHY found for port 0\n");
}
for (i = 0; i < eth->port_num; i++)
phy_config(eth->port[i]);
return rc;
}
static int zynq_phy_init(struct udevice *dev)
{
int ret;
struct zynq_gem_priv *priv = dev_get_priv(dev);
struct zynq_gem_regs *regs = priv->iobase;
const u32 supported = SUPPORTED_10baseT_Half |
SUPPORTED_10baseT_Full |
SUPPORTED_100baseT_Half |
SUPPORTED_100baseT_Full |
SUPPORTED_1000baseT_Half |
SUPPORTED_1000baseT_Full;
/* Enable only MDIO bus */
writel(ZYNQ_GEM_NWCTRL_MDEN_MASK, ®s->nwctrl);
if (priv->interface != PHY_INTERFACE_MODE_SGMII) {
ret = phy_detection(dev);
if (ret) {
printf("GEM PHY init failed\n");
return ret;
}
}
priv->phydev = phy_connect(priv->bus, priv->phyaddr, dev,
priv->interface);
if (!priv->phydev)
return -ENODEV;
priv->phydev->supported = supported | ADVERTISED_Pause |
ADVERTISED_Asym_Pause;
priv->phydev->advertising = priv->phydev->supported;
phy_config(priv->phydev);
return 0;
}
static int mvneta_start(struct udevice *dev)
{
struct mvneta_port *pp = dev_get_priv(dev);
struct phy_device *phydev;
mvneta_port_power_up(pp, pp->phy_interface);
if (!pp->init || pp->link == 0) {
/* Set phy address of the port */
mvreg_write(pp, MVNETA_PHY_ADDR, pp->phyaddr);
phydev = phy_connect(pp->bus, pp->phyaddr, dev,
pp->phy_interface);
pp->phydev = phydev;
phy_config(phydev);
phy_startup(phydev);
if (!phydev->link) {
printf("%s: No link.\n", phydev->dev->name);
return -1;
}
/* Full init on first call */
mvneta_init(dev);
pp->init = 1;
} else {
/* Upon all following calls, this is enough */
mvneta_port_up(pp);
mvneta_port_enable(pp);
}
return 0;
}
static void fec_eth_phy_config(struct eth_device *dev)
{
#ifdef CONFIG_PHYLIB
struct fec_priv *fec = (struct fec_priv *)dev->priv;
struct phy_device *phydev;
phydev = phy_connect(fec->bus, fec->phy_id, dev,
PHY_INTERFACE_MODE_RGMII);
if (phydev) {
fec->phydev = phydev;
phy_config(phydev);
}
#endif
}
void init_host_phys(struct mii_dev *bus)
{
uint k;
for (k = 0; k < 2; ++k) {
struct phy_device *phydev;
phydev = phy_find_by_mask(bus, 1 << k,
PHY_INTERFACE_MODE_SGMII);
if (phydev)
phy_config(phydev);
}
}
static int sh_eth_phy_config(struct sh_eth_dev *eth)
{
int port = eth->port, ret = 0;
struct sh_eth_info *port_info = ð->port_info[port];
struct eth_device *dev = port_info->dev;
struct phy_device *phydev;
phydev = phy_connect(miiphy_get_dev_by_name(dev->name),
port_info->phy_addr, dev, PHY_INTERFACE_MODE_MII);
port_info->phydev = phydev;
phy_config(phydev);
return ret;
}
static int init_phy(struct eth_device *dev)
{
struct fm_eth *fm_eth = dev->priv;
#ifdef CONFIG_PHYLIB
struct phy_device *phydev = NULL;
u32 supported;
#endif
if (fm_eth->type == FM_ETH_1G_E)
dtsec_init_phy(dev);
#ifdef CONFIG_PHYLIB
if (fm_eth->bus) {
phydev = phy_connect(fm_eth->bus, fm_eth->phyaddr, dev,
fm_eth->enet_if);
if (!phydev) {
printf("Failed to connect\n");
return -1;
}
} else {
return 0;
}
if (fm_eth->type == FM_ETH_1G_E) {
supported = (SUPPORTED_10baseT_Half |
SUPPORTED_10baseT_Full |
SUPPORTED_100baseT_Half |
SUPPORTED_100baseT_Full |
SUPPORTED_1000baseT_Full);
} else {
supported = SUPPORTED_10000baseT_Full;
if (tgec_is_fibre(dev))
phydev->port = PORT_FIBRE;
}
phydev->supported &= supported;
phydev->advertising = phydev->supported;
fm_eth->phydev = phydev;
phy_config(phydev);
#endif
return 0;
}
/*
* Discover which PHY is attached to the device, and configure it
* properly. If the PHY is not recognized, then return 0
* (failure). Otherwise, return 1
*/
static int ll_temac_phy_init(struct eth_device *dev)
{
struct ll_temac *ll_temac = dev->priv;
struct phy_device *phydev;
unsigned int supported = PHY_GBIT_FEATURES;
/* interface - look at driver/net/tsec.c */
phydev = phy_connect(ll_temac->bus, ll_temac->phyaddr,
dev, PHY_INTERFACE_MODE_NONE);
phydev->supported &= supported;
phydev->advertising = phydev->supported;
ll_temac->phydev = phydev;
phy_config(phydev);
return 1;
}
static int axiemac_phy_init(struct udevice *dev)
{
u16 phyreg;
u32 i, ret;
struct axidma_priv *priv = dev_get_priv(dev);
struct axi_regs *regs = priv->iobase;
struct phy_device *phydev;
u32 supported = SUPPORTED_10baseT_Half |
SUPPORTED_10baseT_Full |
SUPPORTED_100baseT_Half |
SUPPORTED_100baseT_Full |
SUPPORTED_1000baseT_Half |
SUPPORTED_1000baseT_Full;
/* Set default MDIO divisor */
writel(XAE_MDIO_DIV_DFT | XAE_MDIO_MC_MDIOEN_MASK, ®s->mdio_mc);
if (priv->phyaddr == -1) {
/* Detect the PHY address */
for (i = 31; i >= 0; i--) {
ret = phyread(priv, i, PHY_DETECT_REG, &phyreg);
if (!ret && (phyreg != 0xFFFF) &&
((phyreg & PHY_DETECT_MASK) == PHY_DETECT_MASK)) {
/* Found a valid PHY address */
priv->phyaddr = i;
debug("axiemac: Found valid phy address, %x\n",
i);
break;
}
}
}
/* Interface - look at tsec */
phydev = phy_connect(priv->bus, priv->phyaddr, dev, priv->interface);
phydev->supported &= supported;
phydev->advertising = phydev->supported;
priv->phydev = phydev;
phy_config(phydev);
return 0;
}
static int fec_phy_init(struct fec_priv *priv, struct udevice *dev)
{
struct phy_device *phydev;
int mask = 0xffffffff;
#ifdef CONFIG_PHYLIB
mask = 1 << CONFIG_FEC_MXC_PHYADDR;
#endif
phydev = phy_find_by_mask(priv->bus, mask, priv->interface);
if (!phydev)
return -ENODEV;
phy_connect_dev(phydev, dev);
priv->phydev = phydev;
phy_config(phydev);
return 0;
}
static int init_phy(struct eth_device *dev)
{
struct ldpaa_eth_priv *priv = (struct ldpaa_eth_priv *)dev->priv;
struct phy_device *phydev = NULL;
struct mii_dev *bus;
bus = wriop_get_mdio(priv->dpmac_id);
if (bus == NULL)
return 0;
phydev = phy_connect(bus, wriop_get_phy_address(priv->dpmac_id),
dev, wriop_get_enet_if(priv->dpmac_id));
if (!phydev) {
printf("Failed to connect\n");
return -1;
}
priv->phydev = phydev;
return phy_config(phydev);
}
static int tse_phy_init(struct altera_tse_priv *priv, void *dev)
{
struct phy_device *phydev;
unsigned int mask = 0xffffffff;
if (priv->phyaddr)
mask = 1 << priv->phyaddr;
phydev = phy_find_by_mask(priv->bus, mask, priv->interface);
if (!phydev)
return -ENODEV;
phy_connect_dev(phydev, dev);
phydev->supported &= PHY_GBIT_FEATURES;
phydev->advertising = phydev->supported;
priv->phydev = phydev;
phy_config(phydev);
return 0;
}
static int ftgmac100_phy_init(struct udevice *dev)
{
struct ftgmac100_data *priv = dev_get_priv(dev);
struct phy_device *phydev;
int ret;
phydev = phy_connect(priv->bus, priv->phy_addr, dev, priv->phy_mode);
if (!phydev)
return -ENODEV;
phydev->supported &= PHY_GBIT_FEATURES;
if (priv->max_speed) {
ret = phy_set_supported(phydev, priv->max_speed);
if (ret)
return ret;
}
phydev->advertising = phydev->supported;
priv->phydev = phydev;
phy_config(phydev);
return 0;
}
static int pch_gbe_phy_init(struct eth_device *dev)
{
struct pch_gbe_priv *priv = dev->priv;
struct phy_device *phydev;
int mask = 0xffffffff;
phydev = phy_find_by_mask(priv->bus, mask, priv->interface);
if (!phydev) {
printf("pch_gbe: cannot find the phy\n");
return -1;
}
phy_connect_dev(phydev, dev);
phydev->supported &= PHY_GBIT_FEATURES;
phydev->advertising = phydev->supported;
priv->phydev = phydev;
phy_config(phydev);
return 1;
}
int mvgbe_phylib_init(struct eth_device *dev, int phyid)
{
struct mii_dev *bus;
struct phy_device *phydev;
int ret;
bus = mdio_alloc();
if (!bus) {
printf("mdio_alloc failed\n");
return -ENOMEM;
}
bus->read = mvgbe_phy_read;
bus->write = mvgbe_phy_write;
sprintf(bus->name, dev->name);
ret = mdio_register(bus);
if (ret) {
printf("mdio_register failed\n");
free(bus);
return -ENOMEM;
}
/* Set phy address of the port */
mvgbe_phy_write(bus, MV_PHY_ADR_REQUEST, 0, MV_PHY_ADR_REQUEST, phyid);
phydev = phy_connect(bus, phyid, dev, PHY_INTERFACE_MODE_RGMII);
if (!phydev) {
printf("phy_connect failed\n");
return -ENODEV;
}
phy_config(phydev);
phy_startup(phydev);
return 0;
}
static int fec_probe(bd_t *bd, int dev_id, uint32_t base_addr,
struct mii_dev *bus, int phy_id)
#endif
{
struct eth_device *edev;
struct fec_priv *fec;
unsigned char ethaddr[6];
uint32_t start;
int ret = 0;
/* create and fill edev struct */
edev = (struct eth_device *)malloc(sizeof(struct eth_device));
if (!edev) {
puts("fec_mxc: not enough malloc memory for eth_device\n");
ret = -ENOMEM;
goto err1;
}
fec = (struct fec_priv *)malloc(sizeof(struct fec_priv));
if (!fec) {
puts("fec_mxc: not enough malloc memory for fec_priv\n");
ret = -ENOMEM;
goto err2;
}
memset(edev, 0, sizeof(*edev));
memset(fec, 0, sizeof(*fec));
ret = fec_alloc_descs(fec);
if (ret)
goto err3;
edev->priv = fec;
edev->init = fec_init;
edev->send = fec_send;
edev->recv = fec_recv;
edev->halt = fec_halt;
edev->write_hwaddr = fec_set_hwaddr;
fec->eth = (struct ethernet_regs *)base_addr;
fec->bd = bd;
fec->xcv_type = CONFIG_FEC_XCV_TYPE;
/* Reset chip. */
writel(readl(&fec->eth->ecntrl) | FEC_ECNTRL_RESET, &fec->eth->ecntrl);
start = get_timer(0);
while (readl(&fec->eth->ecntrl) & FEC_ECNTRL_RESET) {
if (get_timer(start) > (CONFIG_SYS_HZ * 5)) {
printf("FEC MXC: Timeout reseting chip\n");
goto err4;
}
udelay(10);
}
fec_reg_setup(fec);
fec_set_dev_name(edev->name, dev_id);
fec->dev_id = (dev_id == -1) ? 0 : dev_id;
fec->bus = bus;
fec_mii_setspeed(bus->priv);
#ifdef CONFIG_PHYLIB
fec->phydev = phydev;
phy_connect_dev(phydev, edev);
/* Configure phy */
phy_config(phydev);
#else
fec->phy_id = phy_id;
#endif
eth_register(edev);
if (fec_get_hwaddr(edev, dev_id, ethaddr) == 0) {
debug("got MAC%d address from fuse: %pM\n", dev_id, ethaddr);
memcpy(edev->enetaddr, ethaddr, 6);
if (!getenv("ethaddr"))
eth_setenv_enetaddr("ethaddr", ethaddr);
}
return ret;
err4:
fec_free_descs(fec);
err3:
free(fec);
err2:
free(edev);
err1:
return ret;
}
static int setup_phy(struct udevice *dev)
{
int i, ret;
u16 phyreg;
struct xemaclite *emaclite = dev_get_priv(dev);
struct phy_device *phydev;
u32 supported = SUPPORTED_10baseT_Half |
SUPPORTED_10baseT_Full |
SUPPORTED_100baseT_Half |
SUPPORTED_100baseT_Full;
if (emaclite->phyaddr != -1) {
phyread(emaclite, emaclite->phyaddr, PHY_DETECT_REG, &phyreg);
if ((phyreg != 0xFFFF) &&
((phyreg & PHY_DETECT_MASK) == PHY_DETECT_MASK)) {
/* Found a valid PHY address */
debug("Default phy address %d is valid\n",
emaclite->phyaddr);
} else {
debug("PHY address is not setup correctly %d\n",
emaclite->phyaddr);
emaclite->phyaddr = -1;
}
}
if (emaclite->phyaddr == -1) {
/* detect the PHY address */
for (i = 31; i >= 0; i--) {
phyread(emaclite, i, PHY_DETECT_REG, &phyreg);
if ((phyreg != 0xFFFF) &&
((phyreg & PHY_DETECT_MASK) == PHY_DETECT_MASK)) {
/* Found a valid PHY address */
emaclite->phyaddr = i;
debug("emaclite: Found valid phy address, %d\n",
i);
break;
}
}
}
/* interface - look at tsec */
phydev = phy_connect(emaclite->bus, emaclite->phyaddr, dev,
PHY_INTERFACE_MODE_MII);
/*
* Phy can support 1000baseT but device NOT that's why phydev->supported
* must be setup for 1000baseT. phydev->advertising setups what speeds
* will be used for autonegotiation where 1000baseT must be disabled.
*/
phydev->supported = supported | SUPPORTED_1000baseT_Half |
SUPPORTED_1000baseT_Full;
phydev->advertising = supported;
emaclite->phydev = phydev;
phy_config(phydev);
ret = phy_startup(phydev);
if (ret)
return ret;
if (!phydev->link) {
printf("%s: No link.\n", phydev->dev->name);
return 0;
}
/* Do not setup anything */
return 1;
}
static int macb_phy_init(struct macb_device *macb, const char *name)
#endif
{
#ifdef CONFIG_DM_ETH
struct macb_device *macb = dev_get_priv(dev);
#endif
u32 ncfgr;
u16 phy_id, status, adv, lpa;
int media, speed, duplex;
int i;
arch_get_mdio_control(name);
/* Auto-detect phy_addr */
if (!macb_phy_find(macb, name))
return 0;
/* Check if the PHY is up to snuff... */
phy_id = macb_mdio_read(macb, MII_PHYSID1);
if (phy_id == 0xffff) {
printf("%s: No PHY present\n", name);
return 0;
}
#ifdef CONFIG_PHYLIB
#ifdef CONFIG_DM_ETH
macb->phydev = phy_connect(macb->bus, macb->phy_addr, dev,
macb->phy_interface);
#else
/* need to consider other phy interface mode */
macb->phydev = phy_connect(macb->bus, macb->phy_addr, &macb->netdev,
PHY_INTERFACE_MODE_RGMII);
#endif
if (!macb->phydev) {
printf("phy_connect failed\n");
return -ENODEV;
}
phy_config(macb->phydev);
#endif
status = macb_mdio_read(macb, MII_BMSR);
if (!(status & BMSR_LSTATUS)) {
/* Try to re-negotiate if we don't have link already. */
macb_phy_reset(macb, name);
for (i = 0; i < MACB_AUTONEG_TIMEOUT / 100; i++) {
status = macb_mdio_read(macb, MII_BMSR);
if (status & BMSR_LSTATUS)
break;
udelay(100);
}
}
if (!(status & BMSR_LSTATUS)) {
printf("%s: link down (status: 0x%04x)\n",
name, status);
return 0;
}
/* First check for GMAC and that it is GiB capable */
if (gem_is_gigabit_capable(macb)) {
lpa = macb_mdio_read(macb, MII_STAT1000);
if (lpa & (LPA_1000FULL | LPA_1000HALF)) {
duplex = ((lpa & LPA_1000FULL) ? 1 : 0);
printf("%s: link up, 1000Mbps %s-duplex (lpa: 0x%04x)\n",
name,
duplex ? "full" : "half",
lpa);
ncfgr = macb_readl(macb, NCFGR);
ncfgr &= ~(MACB_BIT(SPD) | MACB_BIT(FD));
ncfgr |= GEM_BIT(GBE);
if (duplex)
ncfgr |= MACB_BIT(FD);
macb_writel(macb, NCFGR, ncfgr);
return 1;
}
}
/* fall back for EMAC checking */
adv = macb_mdio_read(macb, MII_ADVERTISE);
lpa = macb_mdio_read(macb, MII_LPA);
media = mii_nway_result(lpa & adv);
speed = (media & (ADVERTISE_100FULL | ADVERTISE_100HALF)
? 1 : 0);
duplex = (media & ADVERTISE_FULL) ? 1 : 0;
printf("%s: link up, %sMbps %s-duplex (lpa: 0x%04x)\n",
name,
speed ? "100" : "10",
duplex ? "full" : "half",
lpa);
ncfgr = macb_readl(macb, NCFGR);
ncfgr &= ~(MACB_BIT(SPD) | MACB_BIT(FD) | GEM_BIT(GBE));
if (speed)
ncfgr |= MACB_BIT(SPD);
if (duplex)
ncfgr |= MACB_BIT(FD);
macb_writel(macb, NCFGR, ncfgr);
return 1;
}
/* Setting axi emac and phy to proper setting */
static int setup_phy(struct eth_device *dev)
{
u16 phyreg;
u32 i, speed, emmc_reg, ret;
struct axidma_priv *priv = dev->priv;
struct axi_regs *regs = (struct axi_regs *)dev->iobase;
struct phy_device *phydev;
u32 supported = SUPPORTED_10baseT_Half |
SUPPORTED_10baseT_Full |
SUPPORTED_100baseT_Half |
SUPPORTED_100baseT_Full |
SUPPORTED_1000baseT_Half |
SUPPORTED_1000baseT_Full;
if (priv->phyaddr == -1) {
/* Detect the PHY address */
for (i = 31; i >= 0; i--) {
ret = phyread(dev, i, PHY_DETECT_REG, &phyreg);
if (!ret && (phyreg != 0xFFFF) &&
((phyreg & PHY_DETECT_MASK) == PHY_DETECT_MASK)) {
/* Found a valid PHY address */
priv->phyaddr = i;
debug("axiemac: Found valid phy address, %x\n",
phyreg);
break;
}
}
}
/* Interface - look at tsec */
phydev = phy_connect(priv->bus, priv->phyaddr, dev, 0);
phydev->supported &= supported;
phydev->advertising = phydev->supported;
priv->phydev = phydev;
phy_config(phydev);
if (phy_startup(phydev)) {
printf("axiemac: could not initialize PHY %s\n",
phydev->dev->name);
return 0;
}
switch (phydev->speed) {
case 1000:
speed = XAE_EMMC_LINKSPD_1000;
break;
case 100:
speed = XAE_EMMC_LINKSPD_100;
break;
case 10:
speed = XAE_EMMC_LINKSPD_10;
break;
default:
return 0;
}
/* Setup the emac for the phy speed */
emmc_reg = in_be32(®s->emmc);
emmc_reg &= ~XAE_EMMC_LINKSPEED_MASK;
emmc_reg |= speed;
/* Write new speed setting out to Axi Ethernet */
out_be32(®s->emmc, emmc_reg);
/*
* Setting the operating speed of the MAC needs a delay. There
* doesn't seem to be register to poll, so please consider this
* during your application design.
*/
udelay(1);
return 1;
}
static int macb_phy_init(struct macb_device *macb)
{
struct eth_device *netdev = &macb->netdev;
#ifdef CONFIG_PHYLIB
struct phy_device *phydev;
#endif
u32 ncfgr;
u16 phy_id, status, adv, lpa;
int media, speed, duplex;
int i;
arch_get_mdio_control(netdev->name);
#ifdef CONFIG_MACB_SEARCH_PHY
/* Auto-detect phy_addr */
if (!macb_phy_find(macb)) {
return 0;
}
#endif /* CONFIG_MACB_SEARCH_PHY */
/* Check if the PHY is up to snuff... */
phy_id = macb_mdio_read(macb, MII_PHYSID1);
if (phy_id == 0xffff) {
printf("%s: No PHY present\n", netdev->name);
return 0;
}
#ifdef CONFIG_PHYLIB
phydev->bus = macb->bus;
phydev->dev = netdev;
phydev->addr = macb->phy_addr;
phy_config(phydev);
#endif
status = macb_mdio_read(macb, MII_BMSR);
if (!(status & BMSR_LSTATUS)) {
/* Try to re-negotiate if we don't have link already. */
macb_phy_reset(macb);
for (i = 0; i < CONFIG_SYS_MACB_AUTONEG_TIMEOUT / 100; i++) {
status = macb_mdio_read(macb, MII_BMSR);
if (status & BMSR_LSTATUS)
break;
udelay(100);
}
}
if (!(status & BMSR_LSTATUS)) {
printf("%s: link down (status: 0x%04x)\n",
netdev->name, status);
return 0;
}
/* First check for GMAC */
if (macb_is_gem(macb)) {
lpa = macb_mdio_read(macb, MII_STAT1000);
if (lpa & (1 << 11)) {
speed = 1000;
duplex = 1;
} else {
if (lpa & (1 << 10)) {
speed = 1000;
duplex = 1;
} else {
speed = 0;
}
}
if (speed == 1000) {
printf("%s: link up, %dMbps %s-duplex (lpa: 0x%04x)\n",
netdev->name,
speed,
duplex ? "full" : "half",
lpa);
ncfgr = macb_readl(macb, NCFGR);
ncfgr &= ~(GEM_BIT(GBE) | MACB_BIT(SPD) | MACB_BIT(FD));
if (speed)
ncfgr |= GEM_BIT(GBE);
if (duplex)
ncfgr |= MACB_BIT(FD);
macb_writel(macb, NCFGR, ncfgr);
return 1;
}
}
/* fall back for EMAC checking */
adv = macb_mdio_read(macb, MII_ADVERTISE);
lpa = macb_mdio_read(macb, MII_LPA);
media = mii_nway_result(lpa & adv);
speed = (media & (ADVERTISE_100FULL | ADVERTISE_100HALF)
? 1 : 0);
duplex = (media & ADVERTISE_FULL) ? 1 : 0;
printf("%s: link up, %sMbps %s-duplex (lpa: 0x%04x)\n",
netdev->name,
speed ? "100" : "10",
duplex ? "full" : "half",
lpa);
ncfgr = macb_readl(macb, NCFGR);
ncfgr &= ~(MACB_BIT(SPD) | MACB_BIT(FD));
if (speed)
ncfgr |= MACB_BIT(SPD);
if (duplex)
ncfgr |= MACB_BIT(FD);
macb_writel(macb, NCFGR, ncfgr);
return 1;
}
static int ks2_eth_probe(struct udevice *dev)
{
struct ks2_eth_priv *priv = dev_get_priv(dev);
struct mii_dev *mdio_bus;
int ret;
priv->dev = dev;
/* These clock enables has to be moved to common location */
if (cpu_is_k2g())
writel(KS2_ETHERNET_RGMII, KS2_ETHERNET_CFG);
/* By default, select PA PLL clock as PA clock source */
#ifndef CONFIG_SOC_K2G
if (psc_enable_module(KS2_LPSC_PA))
return -EACCES;
#endif
if (psc_enable_module(KS2_LPSC_CPGMAC))
return -EACCES;
if (psc_enable_module(KS2_LPSC_CRYPTO))
return -EACCES;
if (cpu_is_k2e() || cpu_is_k2l())
pll_pa_clk_sel();
priv->net_rx_buffs.buff_ptr = rx_buffs;
priv->net_rx_buffs.num_buffs = RX_BUFF_NUMS;
priv->net_rx_buffs.buff_len = RX_BUFF_LEN;
if (priv->slave_port == 1) {
/*
* Register MDIO bus for slave 0 only, other slave have
* to re-use the same
*/
mdio_bus = mdio_alloc();
if (!mdio_bus) {
error("MDIO alloc failed\n");
return -ENOMEM;
}
priv->mdio_bus = mdio_bus;
mdio_bus->read = keystone2_mdio_read;
mdio_bus->write = keystone2_mdio_write;
mdio_bus->reset = keystone2_mdio_reset;
mdio_bus->priv = priv->mdio_base;
sprintf(mdio_bus->name, "ethernet-mdio");
ret = mdio_register(mdio_bus);
if (ret) {
error("MDIO bus register failed\n");
return ret;
}
} else {
/* Get the MDIO bus from slave 0 device */
struct ks2_eth_priv *parent_priv;
parent_priv = dev_get_priv(dev->parent);
priv->mdio_bus = parent_priv->mdio_bus;
}
#ifndef CONFIG_SOC_K2G
keystone2_net_serdes_setup();
#endif
priv->netcp_pktdma = &netcp_pktdma;
if (priv->has_mdio) {
priv->phydev = phy_connect(priv->mdio_bus, priv->phy_addr,
dev, priv->phy_if);
phy_config(priv->phydev);
}
return 0;
}
void ls2080a_handle_phy_interface_sgmii(int dpmac_id)
{
int lane, slot;
struct mii_dev *bus;
struct ccsr_gur __iomem *gur = (void *)CONFIG_SYS_FSL_GUTS_ADDR;
int serdes1_prtcl = (in_le32(&gur->rcwsr[28]) &
FSL_CHASSIS3_RCWSR28_SRDS1_PRTCL_MASK)
>> FSL_CHASSIS3_RCWSR28_SRDS1_PRTCL_SHIFT;
int serdes2_prtcl = (in_le32(&gur->rcwsr[28]) &
FSL_CHASSIS3_RCWSR28_SRDS2_PRTCL_MASK)
>> FSL_CHASSIS3_RCWSR28_SRDS2_PRTCL_SHIFT;
int *riser_phy_addr;
char *env_hwconfig = getenv("hwconfig");
if (hwconfig_f("xqsgmii", env_hwconfig))
riser_phy_addr = &xqsgii_riser_phy_addr[0];
else
riser_phy_addr = &sgmii_riser_phy_addr[0];
if (dpmac_id > WRIOP1_DPMAC9)
goto serdes2;
switch (serdes1_prtcl) {
case 0x07:
lane = serdes_get_first_lane(FSL_SRDS_1, SGMII1 + dpmac_id);
slot = lane_to_slot_fsm1[lane];
switch (++slot) {
case 1:
/* Slot housing a SGMII riser card? */
wriop_set_phy_address(dpmac_id,
riser_phy_addr[dpmac_id - 1]);
dpmac_info[dpmac_id].board_mux = EMI1_SLOT1;
bus = mii_dev_for_muxval(EMI1_SLOT1);
wriop_set_mdio(dpmac_id, bus);
dpmac_info[dpmac_id].phydev = phy_connect(
dpmac_info[dpmac_id].bus,
dpmac_info[dpmac_id].phy_addr,
NULL,
dpmac_info[dpmac_id].enet_if);
phy_config(dpmac_info[dpmac_id].phydev);
break;
case 2:
/* Slot housing a SGMII riser card? */
wriop_set_phy_address(dpmac_id,
riser_phy_addr[dpmac_id - 1]);
dpmac_info[dpmac_id].board_mux = EMI1_SLOT2;
bus = mii_dev_for_muxval(EMI1_SLOT2);
wriop_set_mdio(dpmac_id, bus);
dpmac_info[dpmac_id].phydev = phy_connect(
dpmac_info[dpmac_id].bus,
dpmac_info[dpmac_id].phy_addr,
NULL,
dpmac_info[dpmac_id].enet_if);
phy_config(dpmac_info[dpmac_id].phydev);
break;
case 3:
break;
case 4:
break;
case 5:
break;
case 6:
break;
}
break;
default:
printf("%s qds: WRIOP: Unsupported SerDes1 Protocol 0x%02x\n",
__func__ , serdes1_prtcl);
break;
}
serdes2:
switch (serdes2_prtcl) {
case 0x07:
case 0x08:
case 0x49:
lane = serdes_get_first_lane(FSL_SRDS_2, SGMII9 +
(dpmac_id - 9));
slot = lane_to_slot_fsm2[lane];
switch (++slot) {
case 1:
break;
case 3:
break;
case 4:
/* Slot housing a SGMII riser card? */
wriop_set_phy_address(dpmac_id,
riser_phy_addr[dpmac_id - 9]);
dpmac_info[dpmac_id].board_mux = EMI1_SLOT4;
bus = mii_dev_for_muxval(EMI1_SLOT4);
wriop_set_mdio(dpmac_id, bus);
dpmac_info[dpmac_id].phydev = phy_connect(
dpmac_info[dpmac_id].bus,
dpmac_info[dpmac_id].phy_addr,
NULL,
dpmac_info[dpmac_id].enet_if);
phy_config(dpmac_info[dpmac_id].phydev);
break;
case 5:
break;
case 6:
/* Slot housing a SGMII riser card? */
wriop_set_phy_address(dpmac_id,
riser_phy_addr[dpmac_id - 13]);
dpmac_info[dpmac_id].board_mux = EMI1_SLOT6;
bus = mii_dev_for_muxval(EMI1_SLOT6);
wriop_set_mdio(dpmac_id, bus);
break;
}
break;
default:
printf("%s qds: WRIOP: Unsupported SerDes2 Protocol 0x%02x\n",
__func__, serdes2_prtcl);
break;
}
}
void ls2080a_handle_phy_interface_qsgmii(int dpmac_id)
{
int lane = 0, slot;
struct mii_dev *bus;
struct ccsr_gur __iomem *gur = (void *)CONFIG_SYS_FSL_GUTS_ADDR;
int serdes1_prtcl = (in_le32(&gur->rcwsr[28]) &
FSL_CHASSIS3_RCWSR28_SRDS1_PRTCL_MASK)
>> FSL_CHASSIS3_RCWSR28_SRDS1_PRTCL_SHIFT;
switch (serdes1_prtcl) {
case 0x33:
switch (dpmac_id) {
case 1:
case 2:
case 3:
case 4:
lane = serdes_get_first_lane(FSL_SRDS_1, QSGMII_A);
break;
case 5:
case 6:
case 7:
case 8:
lane = serdes_get_first_lane(FSL_SRDS_1, QSGMII_B);
break;
case 9:
case 10:
case 11:
case 12:
lane = serdes_get_first_lane(FSL_SRDS_1, QSGMII_C);
break;
case 13:
case 14:
case 15:
case 16:
lane = serdes_get_first_lane(FSL_SRDS_1, QSGMII_D);
break;
}
slot = lane_to_slot_fsm1[lane];
switch (++slot) {
case 1:
/* Slot housing a QSGMII riser card? */
wriop_set_phy_address(dpmac_id, dpmac_id - 1);
dpmac_info[dpmac_id].board_mux = EMI1_SLOT1;
bus = mii_dev_for_muxval(EMI1_SLOT1);
wriop_set_mdio(dpmac_id, bus);
dpmac_info[dpmac_id].phydev = phy_connect(
dpmac_info[dpmac_id].bus,
dpmac_info[dpmac_id].phy_addr,
NULL,
dpmac_info[dpmac_id].enet_if);
phy_config(dpmac_info[dpmac_id].phydev);
break;
case 3:
break;
case 4:
break;
case 5:
break;
case 6:
break;
}
break;
default:
printf("qds: WRIOP: Unsupported SerDes Protocol 0x%02x\n",
serdes1_prtcl);
break;
}
qsgmii_configure_repeater(dpmac_id);
}
static int zynq_gem_init(struct eth_device *dev, bd_t * bis)
{
u32 i;
unsigned long __maybe_unused clk_rate = 0;
struct phy_device *phydev;
struct zynq_gem_regs *regs = (struct zynq_gem_regs *)dev->iobase;
struct zynq_gem_priv *priv = dev->priv;
struct emac_bd *dummy_tx_bd = &priv->tx_bd[4];
struct emac_bd *dummy_rx_bd = &priv->tx_bd[6];
const u32 supported = SUPPORTED_10baseT_Half |
SUPPORTED_10baseT_Full |
SUPPORTED_100baseT_Half |
SUPPORTED_100baseT_Full |
SUPPORTED_1000baseT_Half |
SUPPORTED_1000baseT_Full;
if (!priv->init) {
/* Disable all interrupts */
writel(0xFFFFFFFF, ®s->idr);
/* Disable the receiver & transmitter */
writel(0, ®s->nwctrl);
writel(0, ®s->txsr);
writel(0, ®s->rxsr);
writel(0, ®s->phymntnc);
/* Clear the Hash registers for the mac address
* pointed by AddressPtr
*/
writel(0x0, ®s->hashl);
/* Write bits [63:32] in TOP */
writel(0x0, ®s->hashh);
/* Clear all counters */
for (i = 0; i < STAT_SIZE; i++)
readl(®s->stat[i]);
/* Setup RxBD space */
memset(priv->rx_bd, 0, RX_BUF * sizeof(struct emac_bd));
for (i = 0; i < RX_BUF; i++) {
priv->rx_bd[i].status = 0xF0000000;
priv->rx_bd[i].addr =
((unsigned long)(priv->rxbuffers) +
(i * PKTSIZE_ALIGN));
}
/* WRAP bit to last BD */
priv->rx_bd[--i].addr |= ZYNQ_GEM_RXBUF_WRAP_MASK;
/* Write RxBDs to IP */
writel((unsigned long)priv->rx_bd, ®s->rxqbase);
/* Setup for DMA Configuration register */
writel(ZYNQ_GEM_DMACR_INIT, ®s->dmacr);
/* Setup for Network Control register, MDIO, Rx and Tx enable */
setbits_le32(®s->nwctrl, ZYNQ_GEM_NWCTRL_MDEN_MASK);
/*
* Disable the second priority queue.
* FIXME: Consider GEMs with more than 2 queues.
*/
dummy_tx_bd->addr = 0;
dummy_tx_bd->status = ZYNQ_GEM_TXBUF_WRAP_MASK |
ZYNQ_GEM_TXBUF_LAST_MASK|
ZYNQ_GEM_TXBUF_USED_MASK;
dummy_rx_bd->addr = ZYNQ_GEM_RXBUF_WRAP_MASK |
ZYNQ_GEM_RXBUF_NEW_MASK;
dummy_rx_bd->status = 0;
flush_dcache_range((ulong)&dummy_tx_bd, (ulong)&dummy_tx_bd +
sizeof(dummy_tx_bd));
flush_dcache_range((ulong)&dummy_rx_bd, (ulong)&dummy_rx_bd +
sizeof(dummy_rx_bd));
writel((unsigned long)dummy_tx_bd, ®s->transmit_q1_ptr);
writel((unsigned long)dummy_rx_bd, ®s->receive_q1_ptr);
priv->init++;
}
phy_detection(dev);
/* interface - look at tsec */
phydev = phy_connect(priv->bus, priv->phyaddr, dev,
priv->interface);
phydev->supported = supported | ADVERTISED_Pause |
ADVERTISED_Asym_Pause;
phydev->advertising = phydev->supported;
priv->phydev = phydev;
phy_config(phydev);
phy_startup(phydev);
phydev->speed = SPEED_1000;
if (!phydev->link) {
printf("%s: No link.\n", phydev->dev->name);
return -1;
}
switch (phydev->speed) {
case SPEED_1000:
writel(ZYNQ_GEM_NWCFG_INIT | ZYNQ_GEM_NWCFG_SPEED1000,
®s->nwcfg);
clk_rate = ZYNQ_GEM_FREQUENCY_1000;
break;
case SPEED_100:
writel(ZYNQ_GEM_NWCFG_INIT | ZYNQ_GEM_NWCFG_SPEED100,
®s->nwcfg);
clk_rate = ZYNQ_GEM_FREQUENCY_100;
break;
case SPEED_10:
clk_rate = ZYNQ_GEM_FREQUENCY_10;
break;
}
/* Change the rclk and clk only not using EMIO interface */
if (!priv->emio)
zynq_slcr_gem_clk_setup(dev->iobase !=
ZYNQ_GEM_BASEADDR0, clk_rate);
/* set hardware address because of ... */
if (!is_valid_ethaddr(dev->enetaddr)) {
printf("%s: mac address is not valid\n", dev->name);
return -1;
}
zynq_gem_setup_mac(dev);
setbits_le32(®s->nwctrl, ZYNQ_GEM_NWCTRL_RXEN_MASK |
ZYNQ_GEM_NWCTRL_TXEN_MASK);
return 0;
}
