/**
* \brief Application entry point for PWM PDC example.
*
* \return Unused (ANSI-C compatibility).
*/
int main(void)
{
uint32_t i;
uint8_t uc_key;
uint8_t c_numkey;
/* Initialize the SAM system */
sysclk_init();
board_init();
/* Configure the console uart for debug infomation */
configure_console();
/* Output example information */
puts(STRING_HEADER);
/* Enable PWM peripheral clock */
pmc_enable_periph_clk(ID_PWM);
/* Disable PWM channel of LED1 and LED0 */
pwm_channel_disable(PWM, PIN_PWM_LED0_CHANNEL);
pwm_channel_disable(PWM, PIN_PWM_LED1_CHANNEL);
/*
* In PWM synchronisation mode the channel0 is used as reference channel,
* so it is necessary to disable, configure and enable it.
*/
if (PIN_PWM_LED0_CHANNEL && PIN_PWM_LED1_CHANNEL) {
pwm_channel_disable(PWM, 0);
}
/* Set PWM clock A as PWM_FREQUENCY*PERIOD_VALUE (clock B is not used) */
pwm_clock_t clock_setting = {
.ul_clka = PWM_FREQUENCY * PERIOD_VALUE,
.ul_clkb = 0,
.ul_mck = sysclk_get_cpu_hz()
};
pwm_init(PWM, &clock_setting);
/* Initialize PWM channels outputs */
pwm_output_t channel_output = {
/* Disable override PWMH outputs */
.b_override_pwmh = false,
/* Disable override PWML outputs */
.b_override_pwml = false,
/* Set override PWMH output level as HIGH */
.override_level_pwmh = PWM_HIGH,
/* Set override PWML output level as LOW */
.override_level_pwml = PWM_LOW
};
/* Initialize PWM synchronous channels */
pwm_channel_t sync_channel = {
/* Use PWM clock A as source clock */
.ul_prescaler = PWM_CMR_CPRE_CLKA,
/* Period value of output waveform */
.ul_period = PERIOD_VALUE,
/* Duty cycle value of output waveform */
.ul_duty = INIT_DUTY_VALUE,
/* Set it as a synchronous channel */
.b_sync_ch = true,
/* Enable dead-time generator */
.b_deadtime_generator = true,
/* Dead-time value for PWMH output */
.us_deadtime_pwmh = INIT_DEAD_TIME,
/* Dead-time value for PWML output */
.us_deadtime_pwml = INIT_DEAD_TIME,
/* Disable override PWMH outputs */
.output_selection.b_override_pwmh = false,
/* Disable override PWML outputs */
.output_selection.b_override_pwml = false
};
/*
* In PWM synchronisation mode the channel0 is used as reference channel,
* so it is necessary to disable, configure and enable it.
*/
if (PIN_PWM_LED0_CHANNEL && PIN_PWM_LED1_CHANNEL) {
sync_channel.channel = 0;
pwm_channel_init(PWM, &sync_channel);
}
/* Initialize PWM channel of LED1 */
sync_channel.channel = PIN_PWM_LED1_CHANNEL;
pwm_channel_init(PWM, &sync_channel);
/* Initialize PWM channel of LED2 */
sync_channel.channel = PIN_PWM_LED0_CHANNEL;
pwm_channel_init(PWM, &sync_channel);
/*
* Initialize PWM synchronous channels
* Synchronous Update Mode: Automatic update duty cycle value by the PDC
* and automatic update of synchronous channels. The update occurs when
* the Update Period elapses (MODE 2).
* Synchronous Update Period = MAX_SYNC_UPDATE_PERIOD.
*/
pwm_sync_init(PWM, PWM_SYNC_UPDATE_MODE_2, MAX_SYNC_UPDATE_PERIOD);
/*
* Request PDC transfer as soon as the synchronous update period elapses
* (comparison unit is ignored).
*/
pwm_pdc_set_request_mode(PWM, PWM_PDC_UPDATE_PERIOD_ELAPSED, (1 << 0));
/* Configure interrupt for PDC transfer */
NVIC_DisableIRQ(PWM_IRQn);
NVIC_ClearPendingIRQ(PWM_IRQn);
NVIC_SetPriority(PWM_IRQn, 0);
NVIC_EnableIRQ(PWM_IRQn);
pwm_pdc_enable_interrupt(PWM, PWM_PDC_TX_END);
/* Fill duty cycle buffer for channel #0 and #1 */
/*
* For PWM channel 0 and 1, duty cycle ranges from
* MIN_DUTY_CYCLE to MAX_DUTY_CYCLE
*/
for (i = 0; i < (DUTY_BUFFER_LENGTH / 3); i++) {
g_us_duty_buffer[i * 3] = (i + INIT_DUTY_VALUE);
g_us_duty_buffer[i * 3 + 1] = (i + INIT_DUTY_VALUE);
g_us_duty_buffer[i * 3 + 2] = (i + INIT_DUTY_VALUE);
}
/* Configure the PDC transfer packet and enable PDC transfer */
g_pdc_tx_packet.ul_addr = (uint32_t) (&(g_us_duty_buffer[0]));
g_pdc_tx_packet.ul_size = DUTY_BUFFER_LENGTH;
pdc_tx_init(PDC_PWM, &g_pdc_tx_packet, 0);
pdc_enable_transfer(PDC_PWM, PERIPH_PTCR_TXTEN);
/* Enable all synchronous channels by enabling channel 0 */
/*
* In PWM synchronisation mode the channel0 is used as reference channel,
* so it is necessary to disable, configure and enable it.
*/
if (PIN_PWM_LED0_CHANNEL && PIN_PWM_LED1_CHANNEL) {
pwm_channel_enable(PWM, 0);
}
pwm_channel_enable(PWM, PIN_PWM_LED0_CHANNEL);
pwm_channel_enable(PWM, PIN_PWM_LED1_CHANNEL);
while (1) {
display_menu();
while (uart_read(CONSOLE_UART, &uc_key));
switch (uc_key) {
case 'u':
case 'U':
printf("Input update period must be between 0 and %d.\r\n",
(int)MAX_SYNC_UPDATE_PERIOD);
c_numkey = get_num_value();
if (c_numkey <= MAX_SYNC_UPDATE_PERIOD) {
/* Set new synchronous update period value */
pwm_sync_change_period(PWM, c_numkey);
printf("Synchronous update period has been changed to %d.\r\n", (int)c_numkey);
} else {
printf("Wrong value, expected value must be one of 0 to %d!\r\n", (int)MAX_SYNC_UPDATE_PERIOD);
}
break;
case 'd':
case 'D':
printf("Input dead time for channel #0 must be between %d and %d.\r\n", INIT_DUTY_VALUE, PERIOD_VALUE);
c_numkey = get_num_value();
if (c_numkey <= PERIOD_VALUE) {
/* Set new dead time value for channel 0 */
pwm_channel_update_dead_time(PWM, &sync_channel,
c_numkey, c_numkey);
/* Update all synchronous channels */
pwm_sync_unlock_update(PWM);
printf("Dead time has been changed to %d.\r\n", (int)c_numkey);
} else {
printf("Wrong value, expected value must be one of %d to %d!\r\n", INIT_DUTY_VALUE, PERIOD_VALUE);
}
break;
case 'o':
case 'O':
if (channel_output.b_override_pwmh
&& channel_output.b_override_pwml) {
/* Disable override outputs of channel 0 synchronously */
channel_output.b_override_pwmh = false;
channel_output.b_override_pwml = false;
pwm_channel_update_output(PWM, &sync_channel,
&channel_output, true);
puts("PWM Channel #0 output override has been disabled.\r\n");
}
else {
/* Enable override outputs of channel 0 synchronously */
channel_output.b_override_pwmh = true;
channel_output.b_override_pwml = true;
pwm_channel_update_output(PWM, &sync_channel,
&channel_output, true);
puts("PWM Channel #0 output has been overridden.\r\n");
}
break;
default:
puts("Unknown input!\r\n");
break;
}
}
}
/**
* \brief Application entry point for PWM PDC example.
*
* \return Unused (ANSI-C compatibility).
*/
int main(void)
{
/* Initialize the SAM system */
sysclk_init();
board_init();
/* Configure the console uart for debug infomation */
configure_console();
/* Output example information */
puts(STRING_HEADER);
/* Enable PWM peripheral clock */
pmc_enable_periph_clk(ID_PWM);
/*A Disable PWM channels
- Register: PWM_DIS (PWM Disable)
- Kanal 0: Motor1_X
- Kanal 1: Motor1_Y
- Kanal 2: Motor1_Z
- Kanal 3: Referenzsignals
*/
pwm_channel_disable(PWM, PWM_CHANNEL_0);
pwm_channel_disable(PWM, PWM_CHANNEL_1);
pwm_channel_disable(PWM, PWM_CHANNEL_2);
pwm_channel_disable(PWM, PWM_CHANNEL_3);
/*A PWM-Leitungen (C.2 - C.9) im Prozessor vom
PIO-Controller trennen und auf peripheral Funktion B setzen */
for (int pinId = 2; pinId <= 9; pinId++) {
pio_set_peripheral(PIOC, PIO_TYPE_PIO_PERIPH_B, (1u << pinId));
}
/*A Clock einstellen
- Set PWM clock A for all channels, clock B not used
*/
pwm_clock_t clock_setting = {
.ul_clka = PWM_FREQUENCY * PERIOD_VALUE,
.ul_clkb = 0,
.ul_mck = sysclk_get_cpu_hz() // diese Funktion gibt 84 Mhz zurück!
};
pwm_init(PWM, &clock_setting);
/*A Kanäle 0,1,2 als synchron festlegen
*/
// zunächst die generellen Eigenschaften der synchronen Channels initialisieren
pwm_channel_t sync_channel = {
/* die Motor Kanäle sollen alle Center aligned sein */
.alignment = PWM_ALIGN_CENTER,
/* die Motor Kanäle sollen mit Low Polarität starten */
.polarity = PWM_LOW,
/* Alle Motor Kanäle sollen Clock A verwenden, da sie mit doppelter Basisfrequenz getaktet werden müssen wegen Center aligned */
.ul_prescaler = PWM_CMR_CPRE_CLKA,
/* Periode einstellen */
.ul_period = PERIOD_VALUE,
/* Duty cycle initial setzen */
.ul_duty = INIT_DUTY_VALUE,
/* der channel soll synchron sein */
.b_sync_ch = true,
.b_deadtime_generator = true,
.us_deadtime_pwmh = 1,
.us_deadtime_pwml = 1
};
/* als erstes dann den Channel 0 initialisieren, indem nur das Channel Attribut in der Struktur von oben neu gesetzt wird,
der REst bleibt gleich...
*/
sync_channel.channel = PWM_CHANNEL_0;
pwm_channel_init(PWM, &sync_channel);
// das gleiche dann mit den beiden anderen zu synchronisierenden Channels
sync_channel.channel = PWM_CHANNEL_1;
pwm_channel_init(PWM, &sync_channel);
sync_channel.channel = PWM_CHANNEL_2;
pwm_channel_init(PWM, &sync_channel);
/*
* Initialize PWM synchronous channels
* Synchronous Update Mode: Automatic update duty cycle value by the PDC
* and automatic update of synchronous channels. The update occurs when
* the Update Period elapses (MODE 2 --> Vorsicht vor Verwirrung: dies entspricht der "Methode 3" aus dem Datasheet!).
* Synchronous Update Period = MAX_SYNC_UPDATE_PERIOD.
*/
pwm_sync_init(PWM, PWM_SYNC_UPDATE_MODE_2, MAX_SYNC_UPDATE_PERIOD);
/*
* Request PDC transfer as soon as the synchronous update period elapses
*/
pwm_pdc_set_request_mode(PWM, PWM_PDC_UPDATE_PERIOD_ELAPSED, (1 << 0));
/* Aktiviere alle synchronen channel durch aktivieren von channel 0, channel 1 und 2 werden automatisch synchron mit gestartet
zusätzlich noch den Refernzchannel "synchron" mitstarten
die ASF funktion channel_enable erlaubt leider nur die Übergabe eines Kanals, also müssen wir hier wohl mit direktem Zugriff auf das Register arbeiten */
pwm_channel_enable(PWM, PWM_CHANNEL_0);
// ref channel funktioniert noch nicht, muss noch debugged werden pwm_channel_enable(PWM, PWM_CHANNEL_3);
pmc_enable_periph_clk(ID_PIOA);
pio_set_output(PIOA, PIO_PA23, LOW, DISABLE, ENABLE);
int angle = 0;
int up = 1;
float sinus = 0;
float a;
while (1) {
pio_set(PIOA, PIO_PA23);
for (int i = 0; i < 1000; i++)
{
sinus = sin(0.343543);
a = sinus;
}
pio_clear(PIOA, PIO_PA23);
delay_us(4);
/*display_menu();
uint32_t angle = get_num_value();
struct SV pwm = get_vector_for_angle(angle);
SVPWM(pwm.u, pwm.v, pwm.w);
printf("The angle is %i degrees.", angle);
for (int i = 0; i <= 360; i++) {
struct SV pwm = get_vector_for_angle(i);
SVPWM(pwm.u, pwm.v, pwm.w);
printf("%i Grad\r\n", i);
delay_ms(40);
}
for (int i = 360; i >= 0; i--) {
struct SV pwm = get_vector_for_angle(i);
SVPWM(pwm.u, pwm.v, pwm.w);
printf("%i Grad\r\n", i);
delay_ms(40);
}*/
}
}
