C++ (Cpp) rockchip_timer_init Examples

Example #1

File: rk3288-board-tpl.c Project: axxia/axxia_u-boot

void board_init_f(ulong dummy)
{
	struct udevice *dev;
	int ret;

	/* Example code showing how to enable the debug UART on RK3288 */
	/* Enable early UART on the RK3288 */
	struct rk3288_grf * const grf = (void *)GRF_BASE;

	rk_clrsetreg(&grf->gpio7ch_iomux, GPIO7C7_MASK << GPIO7C7_SHIFT |
		     GPIO7C6_MASK << GPIO7C6_SHIFT,
		     GPIO7C7_UART2DBG_SOUT << GPIO7C7_SHIFT |
		     GPIO7C6_UART2DBG_SIN << GPIO7C6_SHIFT);
	/*
	 * Debug UART can be used from here if required:
	 *
	 * debug_uart_init();
	 * printch('a');
	 * printhex8(0x1234);
	 * printascii("string");
	 */
	debug_uart_init();

	ret = spl_early_init();
	if (ret) {
		debug("spl_early_init() failed: %d\n", ret);
		hang();
	}

	rockchip_timer_init();
	configure_l2ctlr();

	ret = rockchip_get_clk(&dev);
	if (ret) {
		debug("CLK init failed: %d\n", ret);
		return;
	}

	ret = uclass_get_device(UCLASS_RAM, 0, &dev);
	if (ret) {
		debug("DRAM init failed: %d\n", ret);
		return;
	}
}

Example #2

File: rk3036-board-spl.c Project: 01hyang/u-boot

void board_init_f(ulong dummy)
{
#ifdef EARLY_DEBUG
	/*
	 * NOTE: sd card and debug uart use same iomux in rk3036,
	 * so if you enable uart,
	 * you can not boot from sdcard
	 */
	rk_clrsetreg(&grf->gpio1c_iomux,
		     GPIO1C3_MASK << GPIO1C3_SHIFT |
		     GPIO1C2_MASK << GPIO1C2_SHIFT,
		     GPIO1C3_UART2_SOUT << GPIO1C3_SHIFT |
		     GPIO1C2_UART2_SIN << GPIO1C2_SHIFT);
	debug_uart_init();
#endif
	rockchip_timer_init();
	sdram_init();

	/* return to maskrom */
	back_to_bootrom();
}

Example #3

File: rk3188-board-spl.c Project: bradfa/u-boot

void board_init_f(ulong dummy)
{
	struct udevice *pinctrl, *dev;
	struct rk3188_pmu *pmu;
	int ret;

	/* Example code showing how to enable the debug UART on RK3188 */
#ifdef EARLY_UART
#include <asm/arch/grf_rk3188.h>
	/* Enable early UART on the RK3188 */
#define GRF_BASE	0x20008000
	struct rk3188_grf * const grf = (void *)GRF_BASE;

	rk_clrsetreg(&grf->gpio1b_iomux,
		     GPIO1B1_MASK << GPIO1B1_SHIFT |
		     GPIO1B0_MASK << GPIO1B0_SHIFT,
		     GPIO1B1_UART2_SOUT << GPIO1B1_SHIFT |
		     GPIO1B0_UART2_SIN << GPIO1B0_SHIFT);
	/*
	 * Debug UART can be used from here if required:
	 *
	 * debug_uart_init();
	 * printch('a');
	 * printhex8(0x1234);
	 * printascii("string");
	 */
	debug_uart_init();
	printch('s');
	printch('p');
	printch('l');
	printch('\n');
#endif

	ret = spl_early_init();
	if (ret) {
		debug("spl_early_init() failed: %d\n", ret);
		hang();
	}

	rockchip_timer_init();

	ret = rockchip_get_clk(&dev);
	if (ret) {
		debug("CLK init failed: %d\n", ret);
		return;
	}

	/*
	 * Recover the bootrom's stackpointer.
	 * For whatever reason needs to run after rockchip_get_clk.
	 */
	pmu = syscon_get_first_range(ROCKCHIP_SYSCON_PMU);
	if (IS_ERR(pmu))
		error("pmu syscon returned %ld\n", PTR_ERR(pmu));
	SAVE_SP_ADDR = readl(&pmu->sys_reg[2]);

	ret = uclass_get_device(UCLASS_PINCTRL, 0, &pinctrl);
	if (ret) {
		debug("Pinctrl init failed: %d\n", ret);
		return;
	}

	ret = uclass_get_device(UCLASS_RAM, 0, &dev);
	if (ret) {
		debug("DRAM init failed: %d\n", ret);
		return;
	}

	setup_arm_clock();

#if defined(CONFIG_ROCKCHIP_SPL_BACK_TO_BROM) && !defined(CONFIG_SPL_BOARD_INIT)
	back_to_bootrom();
#endif
}

Example #4

File: rk3288-board-spl.c Project: analogdevicesinc/u-boot-xlnx

void board_init_f(ulong dummy)
{
	struct udevice *pinctrl;
	struct udevice *dev;
	int ret;

	/* Example code showing how to enable the debug UART on RK3288 */
#include <asm/arch/grf_rk3288.h>
	/* Enable early UART on the RK3288 */
#define GRF_BASE	0xff770000
	struct rk3288_grf * const grf = (void *)GRF_BASE;

	rk_clrsetreg(&grf->gpio7ch_iomux, GPIO7C7_MASK << GPIO7C7_SHIFT |
		     GPIO7C6_MASK << GPIO7C6_SHIFT,
		     GPIO7C7_UART2DBG_SOUT << GPIO7C7_SHIFT |
		     GPIO7C6_UART2DBG_SIN << GPIO7C6_SHIFT);
	/*
	 * Debug UART can be used from here if required:
	 *
	 * debug_uart_init();
	 * printch('a');
	 * printhex8(0x1234);
	 * printascii("string");
	 */
	debug_uart_init();
	debug("\nspl:debug uart enabled in %s\n", __func__);
	ret = spl_early_init();
	if (ret) {
		debug("spl_early_init() failed: %d\n", ret);
		hang();
	}

	rockchip_timer_init();
	configure_l2ctlr();

	ret = rockchip_get_clk(&dev);
	if (ret) {
		debug("CLK init failed: %d\n", ret);
		return;
	}

	ret = uclass_get_device(UCLASS_PINCTRL, 0, &pinctrl);
	if (ret) {
		debug("Pinctrl init failed: %d\n", ret);
		return;
	}

#if !defined(CONFIG_SPL_OF_PLATDATA)
	if (of_machine_is_compatible("phytec,rk3288-phycore-som")) {
		ret = phycore_init();
		if (ret) {
			debug("Failed to set up phycore power settings: %d\n",
			      ret);
			return;
		}
	}
#endif

#if !defined(CONFIG_SUPPORT_TPL)
	debug("\nspl:init dram\n");
	ret = uclass_get_device(UCLASS_RAM, 0, &dev);
	if (ret) {
		debug("DRAM init failed: %d\n", ret);
		return;
	}
#endif

#if CONFIG_IS_ENABLED(ROCKCHIP_BACK_TO_BROM) && !defined(CONFIG_SPL_BOARD_INIT)
	back_to_bootrom(BROM_BOOT_NEXTSTAGE);
#endif
}