static void tulip_down (/*RTnet*/struct rtnet_device *rtdev)
{
long ioaddr = rtdev->base_addr;
struct tulip_private *tp = (struct tulip_private *) rtdev->priv;
rtdm_irq_disable(&tp->irq_handle);
rtdm_lock_get(&tp->lock); /* sync with IRQ handler on other cpu -JK- */
/* Disable interrupts by clearing the interrupt mask. */
outl (0x00000000, ioaddr + CSR7);
/* Stop the Tx and Rx processes. */
tulip_stop_rxtx(tp);
/* prepare receive buffers */
tulip_refill_rx(rtdev);
/* release any unconsumed transmit buffers */
tulip_clean_tx_ring(tp);
/* 21040 -- Leave the card in 10baseT state. */
if (tp->chip_id == DC21040)
outl (0x00000004, ioaddr + CSR13);
if (inl (ioaddr + CSR6) != 0xffffffff)
tp->stats.rx_missed_errors += inl (ioaddr + CSR8) & 0xffff;
rtdm_lock_put(&tp->lock);
rtdm_irq_enable(&tp->irq_handle);
rtdev->if_port = tp->saved_if_port;
/* Leave the driver in snooze, not sleep, mode. */
tulip_set_power_state (tp, 0, 1);
}
static int demo_interrupt(rtdm_irq_t *irq_context)
{
struct demodrv_context *ctx;
int dev_id;
// timestamp, if needed, can be obtained list this:
// u64 timestamp = rtdm_clock_read();
int ret = RTDM_IRQ_HANDLED; // usual return value
ctx = rtdm_irq_get_arg(irq_context, struct demodrv_context);
dev_id = ctx->dev_id;
rtdm_lock_get(&ctx->lock);
// do stuff
#ifdef TIMERINT
if (events > EVENT_SIGNAL_COUNT) {
rtdm_event_signal(&ctx->irq_event);
events = 0;
}
#else
rtdm_event_signal(&ctx->irq_event);
#endif
events++;
rtdm_lock_put(&ctx->lock);
// those return values were dropped from the RTDM
// ret = RTDM_IRQ_ENABLE | RTDM_IRQ_PROPAGATE;
#ifdef TIMERINT
// Only propagate the timer interrupt, so that linux sees it.
// Forwarding interrupts to the non-realtime domain is not a common
// use-case of realtime device drivers, so usually DON'T DO THIS.
// But here we grab the important timer interrupt, so we need to propagate it.
return XN_ISR_PROPAGATE;
#else
// signal interrupt is handled and don't propagate the interrupt to linux
return RTDM_IRQ_HANDLED;
#endif
}
static int tulip_rx(/*RTnet*/struct rtnet_device *rtdev, nanosecs_t *time_stamp)
{
struct tulip_private *tp = (struct tulip_private *)rtdev->priv;
int entry = tp->cur_rx % RX_RING_SIZE;
int rx_work_limit = tp->dirty_rx + RX_RING_SIZE - tp->cur_rx;
int received = 0;
if (tulip_debug > 4)
/*RTnet*/rtdm_printk(KERN_DEBUG " In tulip_rx(), entry %d %8.8x.\n", entry,
tp->rx_ring[entry].status);
/* If we own the next entry, it is a new packet. Send it up. */
while ( ! (tp->rx_ring[entry].status & cpu_to_le32(DescOwned))) {
s32 status = le32_to_cpu(tp->rx_ring[entry].status);
if (tulip_debug > 5)
/*RTnet*/rtdm_printk(KERN_DEBUG "%s: In tulip_rx(), entry %d %8.8x.\n",
rtdev->name, entry, status);
if (--rx_work_limit < 0)
break;
if ((status & 0x38008300) != 0x0300) {
if ((status & 0x38000300) != 0x0300) {
/* Ingore earlier buffers. */
if ((status & 0xffff) != 0x7fff) {
if (tulip_debug > 1)
/*RTnet*/rtdm_printk(KERN_WARNING "%s: Oversized Ethernet frame "
"spanned multiple buffers, status %8.8x!\n",
rtdev->name, status);
tp->stats.rx_length_errors++;
}
} else if (status & RxDescFatalErr) {
/* There was a fatal error. */
if (tulip_debug > 2)
/*RTnet*/rtdm_printk(KERN_DEBUG "%s: Receive error, Rx status %8.8x.\n",
rtdev->name, status);
tp->stats.rx_errors++; /* end of a packet.*/
if (status & 0x0890) tp->stats.rx_length_errors++;
if (status & 0x0004) tp->stats.rx_frame_errors++;
if (status & 0x0002) tp->stats.rx_crc_errors++;
if (status & 0x0001) tp->stats.rx_fifo_errors++;
}
} else {
/* Omit the four octet CRC from the length. */
short pkt_len = ((status >> 16) & 0x7ff) - 4;
struct /*RTnet*/rtskb *skb;
#ifndef final_version
if (pkt_len > 1518) {
/*RTnet*/rtdm_printk(KERN_WARNING "%s: Bogus packet size of %d (%#x).\n",
rtdev->name, pkt_len, pkt_len);
pkt_len = 1518;
tp->stats.rx_length_errors++;
}
#endif
#if 0 /*RTnet*/
/* Check if the packet is long enough to accept without copying
to a minimally-sized skbuff. */
if (pkt_len < tulip_rx_copybreak
&& (skb = /*RTnet*/dev_alloc_rtskb(pkt_len + 2)) != NULL) {
skb->rtdev = rtdev;
/*RTnet*/rtskb_reserve(skb, 2); /* 16 byte align the IP header */
pci_dma_sync_single(tp->pdev,
tp->rx_buffers[entry].mapping,
pkt_len, PCI_DMA_FROMDEVICE);
#if ! defined(__alpha__)
//eth_copy_and_sum(skb, tp->rx_buffers[entry].skb->tail,
// pkt_len, 0);
memcpy(rtskb_put(skb, pkt_len),
tp->rx_buffers[entry].skb->tail,
pkt_len);
#else
memcpy(/*RTnet*/rtskb_put(skb, pkt_len),
tp->rx_buffers[entry].skb->tail,
pkt_len);
#endif
} else { /* Pass up the skb already on the Rx ring. */
#endif /*RTnet*/
{
char *temp = /*RTnet*/rtskb_put(skb = tp->rx_buffers[entry].skb,
pkt_len);
#ifndef final_version
if (tp->rx_buffers[entry].mapping !=
le32_to_cpu(tp->rx_ring[entry].buffer1)) {
/*RTnet*/rtdm_printk(KERN_ERR "%s: Internal fault: The skbuff addresses "
"do not match in tulip_rx: %08x vs. %08x ? / %p.\n",
rtdev->name,
le32_to_cpu(tp->rx_ring[entry].buffer1),
tp->rx_buffers[entry].mapping,
temp);/*RTnet*/
}
#endif
pci_unmap_single(tp->pdev, tp->rx_buffers[entry].mapping,
PKT_BUF_SZ, PCI_DMA_FROMDEVICE);
tp->rx_buffers[entry].skb = NULL;
tp->rx_buffers[entry].mapping = 0;
}
skb->protocol = /*RTnet*/rt_eth_type_trans(skb, rtdev);
skb->time_stamp = *time_stamp;
/*RTnet*/rtnetif_rx(skb);
tp->stats.rx_packets++;
tp->stats.rx_bytes += pkt_len;
}
received++;
entry = (++tp->cur_rx) % RX_RING_SIZE;
}
return received;
}
/* The interrupt handler does all of the Rx thread work and cleans up
after the Tx thread. */
int tulip_interrupt(rtdm_irq_t *irq_handle)
{
nanosecs_t time_stamp = rtdm_clock_read();/*RTnet*/
struct rtnet_device *rtdev =
rtdm_irq_get_arg(irq_handle, struct rtnet_device);/*RTnet*/
struct tulip_private *tp = (struct tulip_private *)rtdev->priv;
long ioaddr = rtdev->base_addr;
unsigned int csr5;
int entry;
int missed;
int rx = 0;
int tx = 0;
int oi = 0;
int maxrx = RX_RING_SIZE;
int maxtx = TX_RING_SIZE;
int maxoi = TX_RING_SIZE;
unsigned int work_count = tulip_max_interrupt_work;
/* Let's see whether the interrupt really is for us */
csr5 = inl(ioaddr + CSR5);
if ((csr5 & (NormalIntr|AbnormalIntr)) == 0) {
rtdm_printk("%s: unexpected IRQ!\n",rtdev->name);
return 0;
}
tp->nir++;
do {
/* Acknowledge all of the current interrupt sources ASAP. */
outl(csr5 & 0x0001ffff, ioaddr + CSR5);
if (tulip_debug > 4)
/*RTnet*/rtdm_printk(KERN_DEBUG "%s: interrupt csr5=%#8.8x new csr5=%#8.8x.\n",
rtdev->name, csr5, inl(rtdev->base_addr + CSR5));
if (csr5 & (RxIntr | RxNoBuf)) {
rx += tulip_rx(rtdev, &time_stamp);
tulip_refill_rx(rtdev);
}
if (csr5 & (TxNoBuf | TxDied | TxIntr | TimerInt)) {
unsigned int dirty_tx;
rtdm_lock_get(&tp->lock);
for (dirty_tx = tp->dirty_tx; tp->cur_tx - dirty_tx > 0;
dirty_tx++) {
int entry = dirty_tx % TX_RING_SIZE;
int status = le32_to_cpu(tp->tx_ring[entry].status);
if (status < 0)
break; /* It still has not been Txed */
/* Check for Rx filter setup frames. */
if (tp->tx_buffers[entry].skb == NULL) {
/* test because dummy frames not mapped */
if (tp->tx_buffers[entry].mapping)
pci_unmap_single(tp->pdev,
tp->tx_buffers[entry].mapping,
sizeof(tp->setup_frame),
PCI_DMA_TODEVICE);
continue;
}
if (status & 0x8000) {
/* There was an major error, log it. */
#ifndef final_version
if (tulip_debug > 1)
/*RTnet*/rtdm_printk(KERN_DEBUG "%s: Transmit error, Tx status %8.8x.\n",
rtdev->name, status);
#endif
tp->stats.tx_errors++;
if (status & 0x4104) tp->stats.tx_aborted_errors++;
if (status & 0x0C00) tp->stats.tx_carrier_errors++;
if (status & 0x0200) tp->stats.tx_window_errors++;
if (status & 0x0002) tp->stats.tx_fifo_errors++;
if ((status & 0x0080) && tp->full_duplex == 0)
tp->stats.tx_heartbeat_errors++;
} else {
tp->stats.tx_bytes +=
tp->tx_buffers[entry].skb->len;
tp->stats.collisions += (status >> 3) & 15;
tp->stats.tx_packets++;
}
pci_unmap_single(tp->pdev, tp->tx_buffers[entry].mapping,
tp->tx_buffers[entry].skb->len,
PCI_DMA_TODEVICE);
/* Free the original skb. */
/*RTnet*/dev_kfree_rtskb(tp->tx_buffers[entry].skb);
tp->tx_buffers[entry].skb = NULL;
tp->tx_buffers[entry].mapping = 0;
tx++;
rtnetif_tx(rtdev);
}
#ifndef final_version
if (tp->cur_tx - dirty_tx > TX_RING_SIZE) {
/*RTnet*/rtdm_printk(KERN_ERR "%s: Out-of-sync dirty pointer, %d vs. %d.\n",
rtdev->name, dirty_tx, tp->cur_tx);
dirty_tx += TX_RING_SIZE;
}
#endif
if (tp->cur_tx - dirty_tx < TX_RING_SIZE - 2)
/*RTnet*/rtnetif_wake_queue(rtdev);
tp->dirty_tx = dirty_tx;
if (csr5 & TxDied) {
if (tulip_debug > 2)
/*RTnet*/rtdm_printk(KERN_WARNING "%s: The transmitter stopped."
" CSR5 is %x, CSR6 %x, new CSR6 %x.\n",
rtdev->name, csr5, inl(ioaddr + CSR6), tp->csr6);
tulip_restart_rxtx(tp);
}
rtdm_lock_put(&tp->lock);
}
/* Log errors. */
if (csr5 & AbnormalIntr) { /* Abnormal error summary bit. */
if (csr5 == 0xffffffff)
break;
#if 0 /*RTnet*/
if (csr5 & TxJabber) tp->stats.tx_errors++;
if (csr5 & TxFIFOUnderflow) {
if ((tp->csr6 & 0xC000) != 0xC000)
tp->csr6 += 0x4000; /* Bump up the Tx threshold */
else
tp->csr6 |= 0x00200000; /* Store-n-forward. */
/* Restart the transmit process. */
tulip_restart_rxtx(tp);
outl(0, ioaddr + CSR1);
}
if (csr5 & (RxDied | RxNoBuf)) {
if (tp->flags & COMET_MAC_ADDR) {
outl(tp->mc_filter[0], ioaddr + 0xAC);
outl(tp->mc_filter[1], ioaddr + 0xB0);
}
}
if (csr5 & RxDied) { /* Missed a Rx frame. */
tp->stats.rx_missed_errors += inl(ioaddr + CSR8) & 0xffff;
tp->stats.rx_errors++;
tulip_start_rxtx(tp);
}
/*
* NB: t21142_lnk_change() does a del_timer_sync(), so be careful if this
* call is ever done under the spinlock
*/
if (csr5 & (TPLnkPass | TPLnkFail | 0x08000000)) {
if (tp->link_change)
(tp->link_change)(rtdev, csr5);
}
if (csr5 & SytemError) {
int error = (csr5 >> 23) & 7;
/* oops, we hit a PCI error. The code produced corresponds
* to the reason:
* 0 - parity error
* 1 - master abort
* 2 - target abort
* Note that on parity error, we should do a software reset
* of the chip to get it back into a sane state (according
* to the 21142/3 docs that is).
* -- rmk
*/
/*RTnet*/rtdm_printk(KERN_ERR "%s: (%lu) System Error occured (%d)\n",
rtdev->name, tp->nir, error);
}
#endif /*RTnet*/
/*RTnet*/rtdm_printk(KERN_ERR "%s: Error detected, "
"device may not work any more (csr5=%08x)!\n", rtdev->name, csr5);
/* Clear all error sources, included undocumented ones! */
outl(0x0800f7ba, ioaddr + CSR5);
oi++;
}
/* The interrupt handler.
* This is called from the CPM handler, not the MPC core interrupt.
*/
static int scc_enet_interrupt(rtdm_irq_t *irq_handle)
{
struct rtnet_device *rtdev = rtdm_irq_get_arg(irq_handle, struct rtnet_device);
int packets = 0;
struct scc_enet_private *cep;
volatile cbd_t *bdp;
ushort int_events;
int must_restart;
nanosecs_abs_t time_stamp = rtdm_clock_read();
cep = (struct scc_enet_private *)rtdev->priv;
/* Get the interrupt events that caused us to be here.
*/
int_events = cep->sccp->scc_scce;
cep->sccp->scc_scce = int_events;
must_restart = 0;
/* Handle receive event in its own function.
*/
if (int_events & SCCE_ENET_RXF) {
scc_enet_rx(rtdev, &packets, &time_stamp);
}
/* Check for a transmit error. The manual is a little unclear
* about this, so the debug code until I get it figured out. It
* appears that if TXE is set, then TXB is not set. However,
* if carrier sense is lost during frame transmission, the TXE
* bit is set, "and continues the buffer transmission normally."
* I don't know if "normally" implies TXB is set when the buffer
* descriptor is closed.....trial and error :-).
*/
/* Transmit OK, or non-fatal error. Update the buffer descriptors.
*/
if (int_events & (SCCE_ENET_TXE | SCCE_ENET_TXB)) {
rtdm_lock_get(&cep->lock);
bdp = cep->dirty_tx;
while ((bdp->cbd_sc&BD_ENET_TX_READY)==0) {
RT_DEBUG(__FUNCTION__": Tx ok\n");
if ((bdp==cep->cur_tx) && (cep->tx_full == 0))
break;
if (bdp->cbd_sc & BD_ENET_TX_HB) /* No heartbeat */
cep->stats.tx_heartbeat_errors++;
if (bdp->cbd_sc & BD_ENET_TX_LC) /* Late collision */
cep->stats.tx_window_errors++;
if (bdp->cbd_sc & BD_ENET_TX_RL) /* Retrans limit */
cep->stats.tx_aborted_errors++;
if (bdp->cbd_sc & BD_ENET_TX_UN) /* Underrun */
cep->stats.tx_fifo_errors++;
if (bdp->cbd_sc & BD_ENET_TX_CSL) /* Carrier lost */
cep->stats.tx_carrier_errors++;
/* No heartbeat or Lost carrier are not really bad errors.
* The others require a restart transmit command.
*/
if (bdp->cbd_sc &
(BD_ENET_TX_LC | BD_ENET_TX_RL | BD_ENET_TX_UN)) {
must_restart = 1;
cep->stats.tx_errors++;
}
cep->stats.tx_packets++;
/* Deferred means some collisions occurred during transmit,
* but we eventually sent the packet OK.
*/
if (bdp->cbd_sc & BD_ENET_TX_DEF)
cep->stats.collisions++;
/* Free the sk buffer associated with this last transmit.
*/
dev_kfree_rtskb(cep->tx_skbuff[cep->skb_dirty]);
cep->skb_dirty = (cep->skb_dirty + 1) & TX_RING_MOD_MASK;
/* Update pointer to next buffer descriptor to be transmitted.
*/
if (bdp->cbd_sc & BD_ENET_TX_WRAP)
bdp = cep->tx_bd_base;
else
bdp++;
/* I don't know if we can be held off from processing these
* interrupts for more than one frame time. I really hope
* not. In such a case, we would now want to check the
* currently available BD (cur_tx) and determine if any
* buffers between the dirty_tx and cur_tx have also been
* sent. We would want to process anything in between that
* does not have BD_ENET_TX_READY set.
*/
/* Since we have freed up a buffer, the ring is no longer
* full.
*/
if (cep->tx_full) {
cep->tx_full = 0;
if (rtnetif_queue_stopped(rtdev))
rtnetif_wake_queue(rtdev);
}
cep->dirty_tx = (cbd_t *)bdp;
}
if (must_restart) {
volatile cpm8xx_t *cp;
/* Some transmit errors cause the transmitter to shut
* down. We now issue a restart transmit. Since the
* errors close the BD and update the pointers, the restart
* _should_ pick up without having to reset any of our
* pointers either.
*/
cp = cpmp;
cp->cp_cpcr =
mk_cr_cmd(CPM_CR_ENET, CPM_CR_RESTART_TX) | CPM_CR_FLG;
while (cp->cp_cpcr & CPM_CR_FLG);
}
rtdm_lock_put(&cep->lock);
}
/* Check for receive busy, i.e. packets coming but no place to
* put them. This "can't happen" because the receive interrupt
* is tossing previous frames.
*/
if (int_events & SCCE_ENET_BSY) {
cep->stats.rx_dropped++;
rtdm_printk("CPM ENET: BSY can't happen.\n");
}
if (packets > 0)
rt_mark_stack_mgr(rtdev);
return RTDM_IRQ_HANDLED;
}
static int
scc_enet_start_xmit(struct rtskb *skb, struct rtnet_device *rtdev)
{
struct scc_enet_private *cep = (struct scc_enet_private *)rtdev->priv;
volatile cbd_t *bdp;
rtdm_lockctx_t context;
RT_DEBUG(__FUNCTION__": ...\n");
/* Fill in a Tx ring entry */
bdp = cep->cur_tx;
#ifndef final_version
if (bdp->cbd_sc & BD_ENET_TX_READY) {
/* Ooops. All transmit buffers are full. Bail out.
* This should not happen, since cep->tx_busy should be set.
*/
rtdm_printk("%s: tx queue full!.\n", rtdev->name);
return 1;
}
#endif
/* Clear all of the status flags.
*/
bdp->cbd_sc &= ~BD_ENET_TX_STATS;
/* If the frame is short, tell CPM to pad it.
*/
if (skb->len <= ETH_ZLEN)
bdp->cbd_sc |= BD_ENET_TX_PAD;
else
bdp->cbd_sc &= ~BD_ENET_TX_PAD;
/* Set buffer length and buffer pointer.
*/
bdp->cbd_datlen = skb->len;
bdp->cbd_bufaddr = __pa(skb->data);
/* Save skb pointer.
*/
cep->tx_skbuff[cep->skb_cur] = skb;
cep->stats.tx_bytes += skb->len;
cep->skb_cur = (cep->skb_cur+1) & TX_RING_MOD_MASK;
/* Prevent interrupts from changing the Tx ring from underneath us. */
// *** RTnet ***
#if 0
rtdm_irq_disable(&cep->irq_handle);
rtdm_lock_get(&cep->lock);
#else
rtdm_lock_get_irqsave(&cep->lock, context);
#endif
/* Get and patch time stamp just before the transmission */
if (skb->xmit_stamp)
*skb->xmit_stamp = cpu_to_be64(rtdm_clock_read() + *skb->xmit_stamp);
/* Push the data cache so the CPM does not get stale memory
* data.
*/
flush_dcache_range((unsigned long)(skb->data),
(unsigned long)(skb->data + skb->len));
/* Send it on its way. Tell CPM its ready, interrupt when done,
* its the last BD of the frame, and to put the CRC on the end.
*/
bdp->cbd_sc |= (BD_ENET_TX_READY | BD_ENET_TX_INTR | BD_ENET_TX_LAST | BD_ENET_TX_TC);
#if 0
dev->trans_start = jiffies;
#endif
/* If this was the last BD in the ring, start at the beginning again.
*/
if (bdp->cbd_sc & BD_ENET_TX_WRAP)
bdp = cep->tx_bd_base;
else
bdp++;
if (bdp->cbd_sc & BD_ENET_TX_READY) {
rtnetif_stop_queue(rtdev);
cep->tx_full = 1;
}
cep->cur_tx = (cbd_t *)bdp;
// *** RTnet ***
#if 0
rtdm_lock_put(&cep->lock);
rtdm_irq_enable(&cep->irq_handle);
#else
rtdm_lock_put_irqrestore(&cep->lock, context);
#endif
return 0;
}
/* During a receive, the cur_rx points to the current incoming buffer.
* When we update through the ring, if the next incoming buffer has
* not been given to the system, we just set the empty indicator,
* effectively tossing the packet.
*/
static void
fec_enet_rx(struct rtnet_device *ndev, int *packets, nanosecs_abs_t *time_stamp)
{
struct fec_enet_private *fep = rtnetdev_priv(ndev);
const struct platform_device_id *id_entry =
platform_get_device_id(fep->pdev);
struct bufdesc *bdp;
unsigned short status;
struct rtskb *skb;
ushort pkt_len;
__u8 *data;
#ifdef CONFIG_M532x
flush_cache_all();
#endif
rtdm_lock_get(&fep->hw_lock);
/* First, grab all of the stats for the incoming packet.
* These get messed up if we get called due to a busy condition.
*/
bdp = fep->cur_rx;
while (!((status = bdp->cbd_sc) & BD_ENET_RX_EMPTY)) {
/* Since we have allocated space to hold a complete frame,
* the last indicator should be set.
*/
if ((status & BD_ENET_RX_LAST) == 0)
printk("FEC ENET: rcv is not +last\n");
if (!fep->opened)
goto rx_processing_done;
/* Check for errors. */
if (status & (BD_ENET_RX_LG | BD_ENET_RX_SH | BD_ENET_RX_NO |
BD_ENET_RX_CR | BD_ENET_RX_OV)) {
fep->stats.rx_errors++;
if (status & (BD_ENET_RX_LG | BD_ENET_RX_SH)) {
/* Frame too long or too short. */
fep->stats.rx_length_errors++;
}
if (status & BD_ENET_RX_NO) /* Frame alignment */
fep->stats.rx_frame_errors++;
if (status & BD_ENET_RX_CR) /* CRC Error */
fep->stats.rx_crc_errors++;
if (status & BD_ENET_RX_OV) /* FIFO overrun */
fep->stats.rx_fifo_errors++;
}
/* Report late collisions as a frame error.
* On this error, the BD is closed, but we don't know what we
* have in the buffer. So, just drop this frame on the floor.
*/
if (status & BD_ENET_RX_CL) {
fep->stats.rx_errors++;
fep->stats.rx_frame_errors++;
goto rx_processing_done;
}
/* Process the incoming frame. */
fep->stats.rx_packets++;
pkt_len = bdp->cbd_datlen;
fep->stats.rx_bytes += pkt_len;
data = (__u8*)__va(bdp->cbd_bufaddr);
dma_unmap_single(&fep->pdev->dev, bdp->cbd_bufaddr,
FEC_ENET_TX_FRSIZE, DMA_FROM_DEVICE);
if (id_entry->driver_data & FEC_QUIRK_SWAP_FRAME)
swap_buffer(data, pkt_len);
/* This does 16 byte alignment, exactly what we need.
* The packet length includes FCS, but we don't want to
* include that when passing upstream as it messes up
* bridging applications.
*/
skb = dev_alloc_rtskb(pkt_len - 4 + NET_IP_ALIGN,
&fep->skb_pool); /* RTnet */
if (unlikely(!skb)) {
printk("%s: Memory squeeze, dropping packet.\n",
ndev->name);
fep->stats.rx_dropped++;
} else {
rtskb_reserve(skb, NET_IP_ALIGN);
rtskb_put(skb, pkt_len - 4); /* Make room */
memcpy(skb->data, data, pkt_len - 4);
skb->protocol = rt_eth_type_trans(skb, ndev);
skb->rtdev = ndev;
skb->time_stamp = *time_stamp;
rtnetif_rx(skb);
(*packets)++; /* RTnet */
}
bdp->cbd_bufaddr = dma_map_single(&fep->pdev->dev, data,
FEC_ENET_TX_FRSIZE, DMA_FROM_DEVICE);
rx_processing_done:
/* Clear the status flags for this buffer */
status &= ~BD_ENET_RX_STATS;
/* Mark the buffer empty */
status |= BD_ENET_RX_EMPTY;
bdp->cbd_sc = status;
/* Update BD pointer to next entry */
if (status & BD_ENET_RX_WRAP)
bdp = fep->rx_bd_base;
else
bdp++;
/* Doing this here will keep the FEC running while we process
* incoming frames. On a heavily loaded network, we should be
* able to keep up at the expense of system resources.
*/
writel(0, fep->hwp + FEC_R_DES_ACTIVE);
}
fep->cur_rx = bdp;
rtdm_lock_put(&fep->hw_lock);
}
static void
fec_enet_tx(struct rtnet_device *ndev)
{
struct fec_enet_private *fep;
struct bufdesc *bdp;
unsigned short status;
struct rtskb *skb;
fep = rtnetdev_priv(ndev);
rtdm_lock_get(&fep->hw_lock);
bdp = fep->dirty_tx;
while (((status = bdp->cbd_sc) & BD_ENET_TX_READY) == 0) {
if (bdp == fep->cur_tx && fep->tx_full == 0)
break;
dma_unmap_single(&fep->pdev->dev, bdp->cbd_bufaddr,
FEC_ENET_TX_FRSIZE, DMA_TO_DEVICE);
bdp->cbd_bufaddr = 0;
skb = fep->tx_skbuff[fep->skb_dirty];
/* Check for errors. */
if (status & (BD_ENET_TX_HB | BD_ENET_TX_LC |
BD_ENET_TX_RL | BD_ENET_TX_UN |
BD_ENET_TX_CSL)) {
fep->stats.tx_errors++;
if (status & BD_ENET_TX_HB) /* No heartbeat */
fep->stats.tx_heartbeat_errors++;
if (status & BD_ENET_TX_LC) /* Late collision */
fep->stats.tx_window_errors++;
if (status & BD_ENET_TX_RL) /* Retrans limit */
fep->stats.tx_aborted_errors++;
if (status & BD_ENET_TX_UN) /* Underrun */
fep->stats.tx_fifo_errors++;
if (status & BD_ENET_TX_CSL) /* Carrier lost */
fep->stats.tx_carrier_errors++;
} else {
fep->stats.tx_packets++;
}
if (status & BD_ENET_TX_READY)
printk("HEY! Enet xmit interrupt and TX_READY.\n");
/* Deferred means some collisions occurred during transmit,
* but we eventually sent the packet OK.
*/
if (status & BD_ENET_TX_DEF)
fep->stats.collisions++;
/* Free the sk buffer associated with this last transmit */
dev_kfree_rtskb(skb); /* RTnet */
fep->tx_skbuff[fep->skb_dirty] = NULL;
fep->skb_dirty = (fep->skb_dirty + 1) & TX_RING_MOD_MASK;
/* Update pointer to next buffer descriptor to be transmitted */
if (status & BD_ENET_TX_WRAP)
bdp = fep->tx_bd_base;
else
bdp++;
/* Since we have freed up a buffer, the ring is no longer full
*/
if (fep->tx_full) {
fep->tx_full = 0;
if (rtnetif_queue_stopped(ndev))
rtnetif_wake_queue(ndev);
}
}
fep->dirty_tx = bdp;
rtdm_lock_put(&fep->hw_lock);
}
