void up_disable_irq(int irq)
{
irqstate_t flags;
if (irq < SAM_IRQ_NINT)
{
/* These operations must be atomic */
flags = irqsave();
/* Select the register set associated with this irq */
putreg32(irq, SAM_AIC_SSR);
/* Disable the interrupt */
putreg32(AIC_IDCR_INTD, SAM_AIC_IDCR);
sam_dumpaic("disable", irq);
irqrestore(flags);
}
#ifdef CONFIG_SAMA5_PIO_IRQ
else
{
/* Maybe it is a (derived) PIO IRQ */
sam_pioirqdisable(irq);
}
#endif
sam_dumpaic("disable", irq);
}
int sam_ajoy_initialization(void)
{
int ret;
int fd;
int i;
/* NOTE: The ADC driver was initialized earlier in the bring-up sequence. */
/* Open the ADC driver for reading. */
fd = open("/dev/adc0", O_RDONLY);
if (fd < 0)
{
int errcode = get_errno();
ierr("ERROR: Failed to open /dev/adc0: %d\n", errcode);
return -errcode;
}
/* Detach the file structure from the file descriptor so that it can be
* used on any thread.
*/
ret = file_detach(fd, &g_adcfile);
if (ret < 0)
{
ierr("ERROR: Failed to detach from file descriptor: %d\n", ret);
(void)close(fd);
return ret;
}
/* Configure the GPIO pins as interrupting inputs. */
for (i = 0; i < AJOY_NGPIOS; i++)
{
/* Configure the PIO as an input */
sam_configpio(g_joypio[i]);
/* Configure PIO interrupts, attach the interrupt handler, but leave
* the interrupt disabled.
*/
sam_pioirq(g_joypio[i]);
(void)irq_attach(g_joyirq[i], ajoy_interrupt);
sam_pioirqdisable(g_joyirq[i]);
}
/* Register the joystick device as /dev/ajoy0 */
ret = ajoy_register("/dev/ajoy0", &g_ajoylower);
if (ret < 0)
{
ierr("ERROR: ajoy_register failed: %d\n", ret);
file_close_detached(&g_adcfile);
}
return ret;
}
static void sam_gmac_phy_enable(bool enable)
{
phydbg("IRQ%d: enable=%d\n", IRQ_INT_ETH0, enable);
if (enable)
{
sam_pioirqenable(IRQ_INT_ETH0);
}
else
{
sam_pioirqdisable(IRQ_INT_ETH0);
}
}
static void sam_emac1_phy_enable(bool enable)
{
phyinfo("IRQ%d: enable=%d\n", IRQ_INT_ETH1, enable);
if (enable)
{
sam_pioirqenable(IRQ_INT_ETH1);
}
else
{
sam_pioirqdisable(IRQ_INT_ETH1);
}
}
xcpt_t board_button_irq(int id, xcpt_t irqhandler)
{
xcpt_t oldhandler = NULL;
if (id == BUTTON_USER)
{
irqstate_t flags;
/* Disable interrupts until we are done. This guarantees that the
* following operations are atomic.
*/
flags = irqsave();
/* Get the old button interrupt handler and save the new one */
oldhandler = g_irquser1;
g_irquser1 = irqhandler;
/* Are we attaching or detaching? */
if (irqhandler != NULL)
{
/* Configure the interrupt */
sam_pioirq(PIO_BTN_USER);
(void)irq_attach(IRQ_BTN_USER, irqhandler);
sam_pioirqenable(IRQ_BTN_USER);
}
else
{
/* Disable and detach the interrupt */
sam_pioirqdisable(IRQ_BTN_USER);
(void)irq_detach(IRQ_BTN_USER);
}
irqrestore(flags);
}
/* Return the old button handler (so that it can be restored) */
return oldhandler;
}
static void ajoy_disable(void)
{
irqstate_t flags;
int i;
/* Disable each joystick interrupt */
flags = enter_critical_section();
for (i = 0; i < AJOY_NGPIOS; i++)
{
sam_pioirqdisable(g_joyirq[i]);
}
leave_critical_section(flags);
/* Nullify the handler and argument */
g_ajoyhandler = NULL;
g_ajoyarg = NULL;
}
xcpt_t arch_phy_irq(FAR const char *intf, xcpt_t handler, phy_enable_t *enable)
{
irqstate_t flags;
xcpt_t *phandler;
xcpt_t oldhandler;
pio_pinset_t pinset;
phy_enable_t enabler;
int irq;
DEBUGASSERT(intf);
nvdbg("%s: handler=%p\n", intf, handler);
#ifdef CONFIG_SAMA5_EMACA
phydbg("EMAC: devname=%s\n", SAMA5_EMAC_DEVNAME);
#endif
#ifdef CONFIG_SAMA5_GMAC
phydbg("GMAC: devname=%s\n", SAMA5_GMAC_DEVNAME);
#endif
#ifdef CONFIG_SAMA5_EMACA
if (strcmp(intf, SAMA5_EMAC_DEVNAME) == 0)
{
phydbg("Select EMAC\n");
phandler = &g_emac_handler;
pinset = PIO_INT_ETH1;
irq = IRQ_INT_ETH1;
enabler = sam_emac_phy_enable;
}
else
#endif
#ifdef CONFIG_SAMA5_GMAC
if (strcmp(intf, SAMA5_GMAC_DEVNAME) == 0)
{
phydbg("Select GMAC\n");
phandler = &g_gmac_handler;
pinset = PIO_INT_ETH0;
irq = IRQ_INT_ETH0;
enabler = sam_gmac_phy_enable;
}
else
#endif
{
ndbg("Unsupported interface: %s\n", intf);
return NULL;
}
/* Disable interrupts until we are done. This guarantees that the
* following operations are atomic.
*/
flags = irqsave();
/* Get the old interrupt handler and save the new one */
oldhandler = *phandler;
*phandler = handler;
/* Configure the interrupt */
if (handler)
{
phydbg("Configure pin: %08x\n", pinset);
sam_pioirq(pinset);
phydbg("Attach IRQ%d\n", irq);
(void)irq_attach(irq, handler);
}
else
{
phydbg("Detach IRQ%d\n", irq);
(void)irq_detach(irq);
enabler = NULL;
}
/* Return with the interrupt disabled in either case */
sam_pioirqdisable(irq);
/* Return the enabling function pointer */
if (enable)
{
*enable = enabler;
}
/* Return the old handler (so that it can be restored) */
irqrestore(flags);
return oldhandler;
}
