/* ************************************************************************
*
* Setup the architecture
*
*/
static void __init
sbc8560_setup_arch(void)
{
struct ocp_def *def;
struct ocp_gfar_data *einfo;
bd_t *binfo = (bd_t *) __res;
unsigned int freq;
/* get the core frequency */
freq = binfo->bi_intfreq;
if (ppc_md.progress)
ppc_md.progress("sbc8560_setup_arch()", 0);
/* Set loops_per_jiffy to a half-way reasonable value,
for use until calibrate_delay gets called. */
loops_per_jiffy = freq / HZ;
#ifdef CONFIG_PCI
/* setup PCI host bridges */
mpc85xx_setup_hose();
#endif
#ifdef CONFIG_SERIAL_8250
sbc8560_early_serial_map();
#endif
#ifdef CONFIG_SERIAL_TEXT_DEBUG
/* Invalidate the entry we stole earlier the serial ports
* should be properly mapped */
invalidate_tlbcam_entry(NUM_TLBCAMS - 1);
#endif
/* Set up MAC addresses for the Ethernet devices */
def = ocp_get_one_device(OCP_VENDOR_FREESCALE, OCP_FUNC_GFAR, 0);
if (def) {
einfo = (struct ocp_gfar_data *) def->additions;
memcpy(einfo->mac_addr, binfo->bi_enetaddr, 6);
}
def = ocp_get_one_device(OCP_VENDOR_FREESCALE, OCP_FUNC_GFAR, 1);
if (def) {
einfo = (struct ocp_gfar_data *) def->additions;
memcpy(einfo->mac_addr, binfo->bi_enet1addr, 6);
}
#ifdef CONFIG_BLK_DEV_INITRD
if (initrd_start)
ROOT_DEV = Root_RAM0;
else
#endif
#ifdef CONFIG_ROOT_NFS
ROOT_DEV = Root_NFS;
#else
ROOT_DEV = Root_HDA1;
#endif
ocp_for_each_device(mpc85xx_update_paddr_ocp, &(binfo->bi_immr_base));
}
/* ************************************************************************
*
* Setup the architecture
*
*/
static void __init
sbc8560_setup_arch(void)
{
bd_t *binfo = (bd_t *) __res;
unsigned int freq;
struct gianfar_platform_data *pdata;
struct gianfar_mdio_data *mdata;
/* get the core frequency */
freq = binfo->bi_intfreq;
if (ppc_md.progress)
ppc_md.progress("sbc8560_setup_arch()", 0);
/* Set loops_per_jiffy to a half-way reasonable value,
for use until calibrate_delay gets called. */
loops_per_jiffy = freq / HZ;
#ifdef CONFIG_PCI
/* setup PCI host bridges */
mpc85xx_setup_hose();
#endif
#ifdef CONFIG_SERIAL_8250
sbc8560_early_serial_map();
#endif
#ifdef CONFIG_SERIAL_TEXT_DEBUG
/* Invalidate the entry we stole earlier the serial ports
* should be properly mapped */
invalidate_tlbcam_entry(num_tlbcam_entries - 1);
#endif
/* setup the board related info for the MDIO bus */
mdata = (struct gianfar_mdio_data *) ppc_sys_get_pdata(MPC85xx_MDIO);
mdata->irq[25] = MPC85xx_IRQ_EXT6;
mdata->irq[26] = MPC85xx_IRQ_EXT7;
mdata->irq[31] = -1;
/* setup the board related information for the enet controllers */
pdata = (struct gianfar_platform_data *) ppc_sys_get_pdata(MPC85xx_TSEC1);
if (pdata) {
pdata->board_flags = FSL_GIANFAR_BRD_HAS_PHY_INTR;
pdata->bus_id = 0;
pdata->phy_id = 25;
memcpy(pdata->mac_addr, binfo->bi_enetaddr, 6);
}
pdata = (struct gianfar_platform_data *) ppc_sys_get_pdata(MPC85xx_TSEC2);
if (pdata) {
pdata->board_flags = FSL_GIANFAR_BRD_HAS_PHY_INTR;
pdata->bus_id = 0;
pdata->phy_id = 26;
memcpy(pdata->mac_addr, binfo->bi_enet1addr, 6);
}
#ifdef CONFIG_BLK_DEV_INITRD
if (initrd_start)
ROOT_DEV = Root_RAM0;
else
#endif
#ifdef CONFIG_ROOT_NFS
ROOT_DEV = Root_NFS;
#else
ROOT_DEV = Root_HDA1;
#endif
}
