void usb_stor_invoke_transport(struct scsi_cmnd *srb, struct us_data *us)
{
int need_auto_sense;
int result;
scsi_set_resid(srb, 0);
result = us->transport(srb, us);
if (test_bit(US_FLIDX_TIMED_OUT, &us->dflags)) {
US_DEBUGP("-- command was aborted\n");
srb->result = DID_ABORT << 16;
goto Handle_Errors;
}
if (result == USB_STOR_TRANSPORT_ERROR) {
US_DEBUGP("-- transport indicates error, resetting\n");
srb->result = DID_ERROR << 16;
goto Handle_Errors;
}
if (result == USB_STOR_TRANSPORT_NO_SENSE) {
srb->result = SAM_STAT_CHECK_CONDITION;
last_sector_hacks(us, srb);
return;
}
srb->result = SAM_STAT_GOOD;
need_auto_sense = 0;
if ((us->protocol == USB_PR_CB || us->protocol == USB_PR_DPCM_USB) &&
srb->sc_data_direction != DMA_FROM_DEVICE) {
US_DEBUGP("-- CB transport device requiring auto-sense\n");
need_auto_sense = 1;
}
if (result == USB_STOR_TRANSPORT_FAILED) {
US_DEBUGP("-- transport indicates command failure\n");
need_auto_sense = 1;
}
if (unlikely((srb->cmnd[0] == ATA_16 || srb->cmnd[0] == ATA_12) &&
result == USB_STOR_TRANSPORT_GOOD &&
!(us->fflags & US_FL_SANE_SENSE) &&
!(us->fflags & US_FL_BAD_SENSE) &&
!(srb->cmnd[2] & 0x20))) {
US_DEBUGP("-- SAT supported, increasing auto-sense\n");
us->fflags |= US_FL_SANE_SENSE;
}
if ((scsi_get_resid(srb) > 0) &&
!((srb->cmnd[0] == REQUEST_SENSE) ||
(srb->cmnd[0] == INQUIRY) ||
(srb->cmnd[0] == MODE_SENSE) ||
(srb->cmnd[0] == LOG_SENSE) ||
(srb->cmnd[0] == MODE_SENSE_10))) {
US_DEBUGP("-- unexpectedly short transfer\n");
}
if (need_auto_sense) {
int temp_result;
struct scsi_eh_save ses;
int sense_size = US_SENSE_SIZE;
struct scsi_sense_hdr sshdr;
const u8 *scdd;
u8 fm_ili;
if (us->fflags & US_FL_SANE_SENSE)
sense_size = ~0;
Retry_Sense:
US_DEBUGP("Issuing auto-REQUEST_SENSE\n");
scsi_eh_prep_cmnd(srb, &ses, NULL, 0, sense_size);
if (us->subclass == USB_SC_RBC || us->subclass == USB_SC_SCSI ||
us->subclass == USB_SC_CYP_ATACB)
srb->cmd_len = 6;
else
srb->cmd_len = 12;
scsi_set_resid(srb, 0);
temp_result = us->transport(us->srb, us);
scsi_eh_restore_cmnd(srb, &ses);
if (test_bit(US_FLIDX_TIMED_OUT, &us->dflags)) {
US_DEBUGP("-- auto-sense aborted\n");
srb->result = DID_ABORT << 16;
if (sense_size != US_SENSE_SIZE) {
us->fflags &= ~US_FL_SANE_SENSE;
us->fflags |= US_FL_BAD_SENSE;
}
goto Handle_Errors;
}
if (temp_result == USB_STOR_TRANSPORT_FAILED &&
sense_size != US_SENSE_SIZE) {
US_DEBUGP("-- auto-sense failure, retry small sense\n");
sense_size = US_SENSE_SIZE;
us->fflags &= ~US_FL_SANE_SENSE;
us->fflags |= US_FL_BAD_SENSE;
goto Retry_Sense;
}
if (temp_result != USB_STOR_TRANSPORT_GOOD) {
US_DEBUGP("-- auto-sense failure\n");
srb->result = DID_ERROR << 16;
if (!(us->fflags & US_FL_SCM_MULT_TARG))
goto Handle_Errors;
return;
}
if (srb->sense_buffer[7] > (US_SENSE_SIZE - 8) &&
!(us->fflags & US_FL_SANE_SENSE) &&
!(us->fflags & US_FL_BAD_SENSE) &&
(srb->sense_buffer[0] & 0x7C) == 0x70) {
US_DEBUGP("-- SANE_SENSE support enabled\n");
us->fflags |= US_FL_SANE_SENSE;
US_DEBUGP("-- Sense data truncated to %i from %i\n",
US_SENSE_SIZE,
srb->sense_buffer[7] + 8);
srb->sense_buffer[7] = (US_SENSE_SIZE - 8);
}
scsi_normalize_sense(srb->sense_buffer, SCSI_SENSE_BUFFERSIZE,
&sshdr);
US_DEBUGP("-- Result from auto-sense is %d\n", temp_result);
US_DEBUGP("-- code: 0x%x, key: 0x%x, ASC: 0x%x, ASCQ: 0x%x\n",
sshdr.response_code, sshdr.sense_key,
sshdr.asc, sshdr.ascq);
#ifdef CONFIG_USB_STORAGE_DEBUG
usb_stor_show_sense(sshdr.sense_key, sshdr.asc, sshdr.ascq);
#endif
srb->result = SAM_STAT_CHECK_CONDITION;
scdd = scsi_sense_desc_find(srb->sense_buffer,
SCSI_SENSE_BUFFERSIZE, 4);
fm_ili = (scdd ? scdd[3] : srb->sense_buffer[2]) & 0xA0;
if (sshdr.sense_key == 0 && sshdr.asc == 0 && sshdr.ascq == 0 &&
fm_ili == 0) {
if (result == USB_STOR_TRANSPORT_GOOD) {
srb->result = SAM_STAT_GOOD;
srb->sense_buffer[0] = 0x0;
} else {
srb->result = DID_ERROR << 16;
if ((sshdr.response_code & 0x72) == 0x72)
srb->sense_buffer[1] = HARDWARE_ERROR;
else
srb->sense_buffer[2] = HARDWARE_ERROR;
}
}
}
if (unlikely((us->fflags & US_FL_INITIAL_READ10) &&
srb->cmnd[0] == READ_10)) {
if (srb->result == SAM_STAT_GOOD) {
set_bit(US_FLIDX_READ10_WORKED, &us->dflags);
} else if (test_bit(US_FLIDX_READ10_WORKED, &us->dflags)) {
clear_bit(US_FLIDX_READ10_WORKED, &us->dflags);
set_bit(US_FLIDX_REDO_READ10, &us->dflags);
}
if (test_bit(US_FLIDX_REDO_READ10, &us->dflags)) {
clear_bit(US_FLIDX_REDO_READ10, &us->dflags);
srb->result = DID_IMM_RETRY << 16;
srb->sense_buffer[0] = 0;
}
}
if ((srb->result == SAM_STAT_GOOD || srb->sense_buffer[2] == 0) &&
scsi_bufflen(srb) - scsi_get_resid(srb) < srb->underflow)
srb->result = DID_ERROR << 16;
last_sector_hacks(us, srb);
return;
Handle_Errors:
scsi_lock(us_to_host(us));
set_bit(US_FLIDX_RESETTING, &us->dflags);
clear_bit(US_FLIDX_ABORTING, &us->dflags);
scsi_unlock(us_to_host(us));
mutex_unlock(&us->dev_mutex);
result = usb_stor_port_reset(us);
mutex_lock(&us->dev_mutex);
if (result < 0) {
scsi_lock(us_to_host(us));
usb_stor_report_device_reset(us);
scsi_unlock(us_to_host(us));
us->transport_reset(us);
}
clear_bit(US_FLIDX_RESETTING, &us->dflags);
last_sector_hacks(us, srb);
}
/* Invoke the transport and basic error-handling/recovery methods
*
* This is used by the protocol layers to actually send the message to
* the device and receive the response.
*/
void usb_stor_invoke_transport(struct scsi_cmnd *srb, struct us_data *us)
{
int need_auto_sense;
int result;
/* send the command to the transport layer */
srb->resid = 0;
result = us->transport(srb, us);
/* if the command gets aborted by the higher layers, we need to
* short-circuit all other processing
*/
if (test_bit(US_FLIDX_TIMED_OUT, &us->flags)) {
_VMKLNX_USB_STOR_MSG("-- command was aborted\n", srb);
US_DEBUGP("-- command was aborted\n");
srb->result = DID_ABORT << 16;
goto Handle_Errors;
}
#if defined(__VMKLNX__)
if (unlikely(scsi_dump_active(srb))) {
/* can't do much in panic */
if (result != USB_STOR_TRANSPORT_GOOD) {
srb->result = DID_ABORT << 16;
goto Handle_Errors;
}
}
#endif
/* if there is a transport error, reset and don't auto-sense */
if (result == USB_STOR_TRANSPORT_ERROR) {
_VMKLNX_USB_STOR_WARN("-- transport indicates error, resetting\n", srb);
US_DEBUGP("-- transport indicates error, resetting\n");
srb->result = DID_ERROR << 16;
goto Handle_Errors;
}
/* if the transport provided its own sense data, don't auto-sense */
if (result == USB_STOR_TRANSPORT_NO_SENSE) {
#if defined(__VMKLNX__)
BUG_ON(srb->sense_buffer[0] == 0);
#endif
srb->result = SAM_STAT_CHECK_CONDITION;
return;
}
srb->result = SAM_STAT_GOOD;
/* Determine if we need to auto-sense
*
* I normally don't use a flag like this, but it's almost impossible
* to understand what's going on here if I don't.
*/
need_auto_sense = 0;
/*
* If we're running the CB transport, which is incapable
* of determining status on its own, we will auto-sense
* unless the operation involved a data-in transfer. Devices
* can signal most data-in errors by stalling the bulk-in pipe.
*/
if ((us->protocol == US_PR_CB || us->protocol == US_PR_DPCM_USB) &&
srb->sc_data_direction != DMA_FROM_DEVICE) {
_VMKLNX_USB_STOR_MSG("-- CB transport device requiring auto-sense\n", srb);
US_DEBUGP("-- CB transport device requiring auto-sense\n");
need_auto_sense = 1;
}
/*
* If we have a failure, we're going to do a REQUEST_SENSE
* automatically. Note that we differentiate between a command
* "failure" and an "error" in the transport mechanism.
*/
if (result == USB_STOR_TRANSPORT_FAILED) {
_VMKLNX_USB_STOR_MSG("-- transport indicates command failure\n", srb);
US_DEBUGP("-- transport indicates command failure\n");
need_auto_sense = 1;
}
/*
* A short transfer on a command where we don't expect it
* is unusual, but it doesn't mean we need to auto-sense.
*/
if ((srb->resid > 0) &&
!((srb->cmnd[0] == REQUEST_SENSE) ||
(srb->cmnd[0] == INQUIRY) ||
(srb->cmnd[0] == MODE_SENSE) ||
(srb->cmnd[0] == LOG_SENSE) ||
(srb->cmnd[0] == MODE_SENSE_10))) {
_VMKLNX_USB_STOR_MSG("-- unexpectedly short transfer\n", srb);
US_DEBUGP("-- unexpectedly short transfer\n");
}
/* Now, if we need to do the auto-sense, let's do it */
if (need_auto_sense) {
int temp_result;
struct scsi_eh_save ses;
US_DEBUGP("Issuing auto-REQUEST_SENSE\n");
#if defined(__VMKLNX__)
/* use us->senebuf to get sense data; srb->sense_buffer might be above 4G,
* yet device's dma_mask is set to 32-bit */
usb_stor_prep_cmd(srb, &ses, us->sensebuf);
#else
scsi_eh_prep_cmnd(srb, &ses, NULL, 0, US_SENSE_SIZE);
#endif
/* FIXME: we must do the protocol translation here */
if (us->subclass == US_SC_RBC || us->subclass == US_SC_SCSI)
srb->cmd_len = 6;
else
srb->cmd_len = 12;
/* issue the auto-sense command */
srb->resid = 0;
temp_result = us->transport(us->srb, us);
/* let's clean up right away */
#if defined(__VMKLNX__)
usb_stor_restore_cmnd(srb, &ses);
#else
scsi_eh_restore_cmnd(srb, &ses);
#endif
if (test_bit(US_FLIDX_TIMED_OUT, &us->flags)) {
US_DEBUGP("-- auto-sense aborted\n");
srb->result = DID_ABORT << 16;
goto Handle_Errors;
}
if (temp_result != USB_STOR_TRANSPORT_GOOD) {
US_DEBUGP("-- auto-sense failure\n");
/* we skip the reset if this happens to be a
* multi-target device, since failure of an
* auto-sense is perfectly valid
*/
srb->result = DID_ERROR << 16;
if (!(us->flags & US_FL_SCM_MULT_TARG))
goto Handle_Errors;
return;
}
US_DEBUGP("-- Result from auto-sense is %d\n", temp_result);
US_DEBUGP("-- code: 0x%x, key: 0x%x, ASC: 0x%x, ASCQ: 0x%x\n",
srb->sense_buffer[0],
srb->sense_buffer[2] & 0xf,
srb->sense_buffer[12],
srb->sense_buffer[13]);
#ifdef CONFIG_USB_STORAGE_DEBUG
usb_stor_show_sense(
srb->sense_buffer[2] & 0xf,
srb->sense_buffer[12],
srb->sense_buffer[13]);
#endif
/* set the result so the higher layers expect this data */
srb->result = SAM_STAT_CHECK_CONDITION;
#if defined(__VMKLNX__)
if (unlikely(srb->sense_buffer[0] == 0))
_VMKLNX_USB_STOR_MSG("srb->sense_buffer[0] unexpectedly 0 for srb %p\n", srb, srb);
BUG_ON(srb->sense_buffer[0] == 0);
#endif
/* If things are really okay, then let's show that. Zero
* out the sense buffer so the higher layers won't realize
* we did an unsolicited auto-sense. */
if (result == USB_STOR_TRANSPORT_GOOD &&
/* Filemark 0, ignore EOM, ILI 0, no sense */
(srb->sense_buffer[2] & 0xaf) == 0 &&
/* No ASC or ASCQ */
srb->sense_buffer[12] == 0 &&
srb->sense_buffer[13] == 0) {
srb->result = SAM_STAT_GOOD;
srb->sense_buffer[0] = 0x0;
}
}
/* Did we transfer less than the minimum amount required? */
if (srb->result == SAM_STAT_GOOD &&
srb->request_bufflen - srb->resid < srb->underflow)
srb->result = (DID_ERROR << 16) | (SUGGEST_RETRY << 24);
return;
/* Error and abort processing: try to resynchronize with the device
* by issuing a port reset. If that fails, try a class-specific
* device reset. */
Handle_Errors:
/* Set the RESETTING bit, and clear the ABORTING bit so that
* the reset may proceed. */
scsi_lock(us_to_host(us));
set_bit(US_FLIDX_RESETTING, &us->flags);
clear_bit(US_FLIDX_ABORTING, &us->flags);
scsi_unlock(us_to_host(us));
/* We must release the device lock because the pre_reset routine
* will want to acquire it. */
mutex_unlock(&us->dev_mutex);
result = usb_stor_port_reset(us);
mutex_lock(&us->dev_mutex);
if (result < 0) {
scsi_lock(us_to_host(us));
usb_stor_report_device_reset(us);
scsi_unlock(us_to_host(us));
us->transport_reset(us);
}
clear_bit(US_FLIDX_RESETTING, &us->flags);
}
/*
* usb_stor_invoke_transport()
*/
void usb_stor_invoke_transport(struct scsi_cmnd *srb, struct us_data *us)
{
int need_auto_sense;
int result;
/* pr_info("transport --- usb_stor_invoke_transport\n"); */
usb_stor_print_cmd(srb);
/* send the command to the transport layer */
scsi_set_resid(srb, 0);
result = us->transport(srb, us); /* usb_stor_Bulk_transport; */
/* if the command gets aborted by the higher layers,
we need to short-circuit all other processing */
if (test_bit(US_FLIDX_TIMED_OUT, &us->dflags)) {
/* pr_info("-- command was aborted\n"); */
srb->result = DID_ABORT << 16;
goto Handle_Errors;
}
/* if there is a transport error, reset and don't auto-sense */
if (result == USB_STOR_TRANSPORT_ERROR) {
/* pr_info("-- transport indicates error, resetting\n"); */
srb->result = DID_ERROR << 16;
goto Handle_Errors;
}
/* if the transport provided its own sense data, don't auto-sense */
if (result == USB_STOR_TRANSPORT_NO_SENSE) {
srb->result = SAM_STAT_CHECK_CONDITION;
return;
}
srb->result = SAM_STAT_GOOD;
/* Determine if we need to auto-sense */
need_auto_sense = 0;
if ((us->protocol == USB_PR_CB || us->protocol == USB_PR_DPCM_USB) &&
srb->sc_data_direction != DMA_FROM_DEVICE) {
/* pr_info("-- CB transport device requiring auto-sense\n"); */
need_auto_sense = 1;
}
if (result == USB_STOR_TRANSPORT_FAILED) {
/* pr_info("-- transport indicates command failure\n"); */
need_auto_sense = 1;
}
/* Now, if we need to do the auto-sense, let's do it */
if (need_auto_sense) {
int temp_result;
struct scsi_eh_save ses;
pr_info("Issuing auto-REQUEST_SENSE\n");
scsi_eh_prep_cmnd(srb, &ses, NULL, 0, US_SENSE_SIZE);
/* we must do the protocol translation here */
if (us->subclass == USB_SC_RBC ||
us->subclass == USB_SC_SCSI ||
us->subclass == USB_SC_CYP_ATACB) {
srb->cmd_len = 6;
} else {
srb->cmd_len = 12;
}
/* issue the auto-sense command */
scsi_set_resid(srb, 0);
temp_result = us->transport(us->srb, us);
/* let's clean up right away */
scsi_eh_restore_cmnd(srb, &ses);
if (test_bit(US_FLIDX_TIMED_OUT, &us->dflags)) {
/* pr_info("-- auto-sense aborted\n"); */
srb->result = DID_ABORT << 16;
goto Handle_Errors;
}
if (temp_result != USB_STOR_TRANSPORT_GOOD) {
/* pr_info("-- auto-sense failure\n"); */
srb->result = DID_ERROR << 16;
if (!(us->fflags & US_FL_SCM_MULT_TARG))
goto Handle_Errors;
return;
}
/* set the result so the higher layers expect this data */
srb->result = SAM_STAT_CHECK_CONDITION;
if (result == USB_STOR_TRANSPORT_GOOD &&
(srb->sense_buffer[2] & 0xaf) == 0 &&
srb->sense_buffer[12] == 0 &&
srb->sense_buffer[13] == 0) {
srb->result = SAM_STAT_GOOD;
srb->sense_buffer[0] = 0x0;
}
}
/* Did we transfer less than the minimum amount required? */
if (srb->result == SAM_STAT_GOOD && scsi_bufflen(srb) -
scsi_get_resid(srb) < srb->underflow)
srb->result = (DID_ERROR << 16);
/* v02 | (SUGGEST_RETRY << 24); */
return;
Handle_Errors:
scsi_lock(us_to_host(us));
set_bit(US_FLIDX_RESETTING, &us->dflags);
clear_bit(US_FLIDX_ABORTING, &us->dflags);
scsi_unlock(us_to_host(us));
mutex_unlock(&us->dev_mutex);
result = usb_stor_port_reset(us);
mutex_lock(&us->dev_mutex);
if (result < 0) {
scsi_lock(us_to_host(us));
usb_stor_report_device_reset(us);
scsi_unlock(us_to_host(us));
us->transport_reset(us);
}
clear_bit(US_FLIDX_RESETTING, &us->dflags);
}
/* Invoke the transport and basic error-handling/recovery methods
*
* This is used by the protocol layers to actually send the message to
* the device and receive the response.
*/
void usb_stor_invoke_transport(struct scsi_cmnd *srb, struct us_data *us)
{
int need_auto_sense;
int result;
/* send the command to the transport layer */
scsi_set_resid(srb, 0);
result = us->transport(srb, us);
/* if the command gets aborted by the higher layers, we need to
* short-circuit all other processing
*/
if (test_bit(US_FLIDX_TIMED_OUT, &us->dflags)) {
US_DEBUGP("-- command was aborted\n");
srb->result = DID_ABORT << 16;
goto Handle_Errors;
}
/* if there is a transport error, reset and don't auto-sense */
if (result == USB_STOR_TRANSPORT_ERROR) {
US_DEBUGP("-- transport indicates error, resetting\n");
srb->result = DID_ERROR << 16;
goto Handle_Errors;
}
/* if the transport provided its own sense data, don't auto-sense */
if (result == USB_STOR_TRANSPORT_NO_SENSE) {
srb->result = SAM_STAT_CHECK_CONDITION;
last_sector_hacks(us, srb);
return;
}
srb->result = SAM_STAT_GOOD;
/* Determine if we need to auto-sense
*
* I normally don't use a flag like this, but it's almost impossible
* to understand what's going on here if I don't.
*/
need_auto_sense = 0;
/*
* If we're running the CB transport, which is incapable
* of determining status on its own, we will auto-sense
* unless the operation involved a data-in transfer. Devices
* can signal most data-in errors by stalling the bulk-in pipe.
*/
if ((us->protocol == USB_PR_CB || us->protocol == USB_PR_DPCM_USB) &&
srb->sc_data_direction != DMA_FROM_DEVICE) {
US_DEBUGP("-- CB transport device requiring auto-sense\n");
need_auto_sense = 1;
}
/*
* If we have a failure, we're going to do a REQUEST_SENSE
* automatically. Note that we differentiate between a command
* "failure" and an "error" in the transport mechanism.
*/
if (result == USB_STOR_TRANSPORT_FAILED) {
US_DEBUGP("-- transport indicates command failure\n");
need_auto_sense = 1;
}
/*
* Determine if this device is SAT by seeing if the
* command executed successfully. Otherwise we'll have
* to wait for at least one CHECK_CONDITION to determine
* SANE_SENSE support
*/
if (unlikely((srb->cmnd[0] == ATA_16 || srb->cmnd[0] == ATA_12) &&
result == USB_STOR_TRANSPORT_GOOD &&
!(us->fflags & US_FL_SANE_SENSE) &&
!(us->fflags & US_FL_BAD_SENSE) &&
!(srb->cmnd[2] & 0x20))) {
US_DEBUGP("-- SAT supported, increasing auto-sense\n");
us->fflags |= US_FL_SANE_SENSE;
}
/*
* A short transfer on a command where we don't expect it
* is unusual, but it doesn't mean we need to auto-sense.
*/
if ((scsi_get_resid(srb) > 0) &&
!((srb->cmnd[0] == REQUEST_SENSE) ||
(srb->cmnd[0] == INQUIRY) ||
(srb->cmnd[0] == MODE_SENSE) ||
(srb->cmnd[0] == LOG_SENSE) ||
(srb->cmnd[0] == MODE_SENSE_10))) {
US_DEBUGP("-- unexpectedly short transfer\n");
}
/* Now, if we need to do the auto-sense, let's do it */
if (need_auto_sense) {
int temp_result;
struct scsi_eh_save ses;
int sense_size = US_SENSE_SIZE;
struct scsi_sense_hdr sshdr;
const u8 *scdd;
u8 fm_ili;
/* device supports and needs bigger sense buffer */
if (us->fflags & US_FL_SANE_SENSE)
sense_size = ~0;
Retry_Sense:
US_DEBUGP("Issuing auto-REQUEST_SENSE\n");
scsi_eh_prep_cmnd(srb, &ses, NULL, 0, sense_size);
/* FIXME: we must do the protocol translation here */
if (us->subclass == USB_SC_RBC || us->subclass == USB_SC_SCSI ||
us->subclass == USB_SC_CYP_ATACB)
srb->cmd_len = 6;
else
srb->cmd_len = 12;
/* issue the auto-sense command */
scsi_set_resid(srb, 0);
temp_result = us->transport(us->srb, us);
/* let's clean up right away */
scsi_eh_restore_cmnd(srb, &ses);
if (test_bit(US_FLIDX_TIMED_OUT, &us->dflags)) {
US_DEBUGP("-- auto-sense aborted\n");
srb->result = DID_ABORT << 16;
/* If SANE_SENSE caused this problem, disable it */
if (sense_size != US_SENSE_SIZE) {
us->fflags &= ~US_FL_SANE_SENSE;
us->fflags |= US_FL_BAD_SENSE;
}
goto Handle_Errors;
}
/* Some devices claim to support larger sense but fail when
* trying to request it. When a transport failure happens
* using US_FS_SANE_SENSE, we always retry with a standard
* (small) sense request. This fixes some USB GSM modems
*/
if (temp_result == USB_STOR_TRANSPORT_FAILED &&
sense_size != US_SENSE_SIZE) {
US_DEBUGP("-- auto-sense failure, retry small sense\n");
sense_size = US_SENSE_SIZE;
us->fflags &= ~US_FL_SANE_SENSE;
us->fflags |= US_FL_BAD_SENSE;
goto Retry_Sense;
}
/* Other failures */
if (temp_result != USB_STOR_TRANSPORT_GOOD) {
US_DEBUGP("-- auto-sense failure\n");
/* we skip the reset if this happens to be a
* multi-target device, since failure of an
* auto-sense is perfectly valid
*/
srb->result = DID_ERROR << 16;
if (!(us->fflags & US_FL_SCM_MULT_TARG))
goto Handle_Errors;
return;
}
/* If the sense data returned is larger than 18-bytes then we
* assume this device supports requesting more in the future.
* The response code must be 70h through 73h inclusive.
*/
if (srb->sense_buffer[7] > (US_SENSE_SIZE - 8) &&
!(us->fflags & US_FL_SANE_SENSE) &&
!(us->fflags & US_FL_BAD_SENSE) &&
(srb->sense_buffer[0] & 0x7C) == 0x70) {
US_DEBUGP("-- SANE_SENSE support enabled\n");
us->fflags |= US_FL_SANE_SENSE;
/* Indicate to the user that we truncated their sense
* because we didn't know it supported larger sense.
*/
US_DEBUGP("-- Sense data truncated to %i from %i\n",
US_SENSE_SIZE,
srb->sense_buffer[7] + 8);
srb->sense_buffer[7] = (US_SENSE_SIZE - 8);
}
scsi_normalize_sense(srb->sense_buffer, SCSI_SENSE_BUFFERSIZE,
&sshdr);
US_DEBUGP("-- Result from auto-sense is %d\n", temp_result);
US_DEBUGP("-- code: 0x%x, key: 0x%x, ASC: 0x%x, ASCQ: 0x%x\n",
sshdr.response_code, sshdr.sense_key,
sshdr.asc, sshdr.ascq);
#ifdef CONFIG_USB_STORAGE_DEBUG
usb_stor_show_sense(sshdr.sense_key, sshdr.asc, sshdr.ascq);
#endif
/* set the result so the higher layers expect this data */
srb->result = SAM_STAT_CHECK_CONDITION;
scdd = scsi_sense_desc_find(srb->sense_buffer,
SCSI_SENSE_BUFFERSIZE, 4);
fm_ili = (scdd ? scdd[3] : srb->sense_buffer[2]) & 0xA0;
/* We often get empty sense data. This could indicate that
* everything worked or that there was an unspecified
* problem. We have to decide which.
*/
if (sshdr.sense_key == 0 && sshdr.asc == 0 && sshdr.ascq == 0 &&
fm_ili == 0) {
/* If things are really okay, then let's show that.
* Zero out the sense buffer so the higher layers
* won't realize we did an unsolicited auto-sense.
*/
if (result == USB_STOR_TRANSPORT_GOOD) {
srb->result = SAM_STAT_GOOD;
srb->sense_buffer[0] = 0x0;
/* If there was a problem, report an unspecified
* hardware error to prevent the higher layers from
* entering an infinite retry loop.
*/
} else {
srb->result = DID_ERROR << 16;
if ((sshdr.response_code & 0x72) == 0x72)
srb->sense_buffer[1] = HARDWARE_ERROR;
else
srb->sense_buffer[2] = HARDWARE_ERROR;
}
}
}
/*
* Some devices don't work or return incorrect data the first
* time they get a READ(10) command, or for the first READ(10)
* after a media change. If the INITIAL_READ10 flag is set,
* keep track of whether READ(10) commands succeed. If the
* previous one succeeded and this one failed, set the REDO_READ10
* flag to force a retry.
*/
if (unlikely((us->fflags & US_FL_INITIAL_READ10) &&
srb->cmnd[0] == READ_10)) {
if (srb->result == SAM_STAT_GOOD) {
set_bit(US_FLIDX_READ10_WORKED, &us->dflags);
} else if (test_bit(US_FLIDX_READ10_WORKED, &us->dflags)) {
clear_bit(US_FLIDX_READ10_WORKED, &us->dflags);
set_bit(US_FLIDX_REDO_READ10, &us->dflags);
}
/*
* Next, if the REDO_READ10 flag is set, return a result
* code that will cause the SCSI core to retry the READ(10)
* command immediately.
*/
if (test_bit(US_FLIDX_REDO_READ10, &us->dflags)) {
clear_bit(US_FLIDX_REDO_READ10, &us->dflags);
srb->result = DID_IMM_RETRY << 16;
srb->sense_buffer[0] = 0;
}
}
/* Did we transfer less than the minimum amount required? */
if ((srb->result == SAM_STAT_GOOD || srb->sense_buffer[2] == 0) &&
scsi_bufflen(srb) - scsi_get_resid(srb) < srb->underflow)
srb->result = DID_ERROR << 16;
last_sector_hacks(us, srb);
return;
/* Error and abort processing: try to resynchronize with the device
* by issuing a port reset. If that fails, try a class-specific
* device reset. */
Handle_Errors:
/* Set the RESETTING bit, and clear the ABORTING bit so that
* the reset may proceed. */
scsi_lock(us_to_host(us));
set_bit(US_FLIDX_RESETTING, &us->dflags);
clear_bit(US_FLIDX_ABORTING, &us->dflags);
scsi_unlock(us_to_host(us));
/* We must release the device lock because the pre_reset routine
* will want to acquire it. */
mutex_unlock(&us->dev_mutex);
result = usb_stor_port_reset(us);
mutex_lock(&us->dev_mutex);
if (result < 0) {
scsi_lock(us_to_host(us));
usb_stor_report_device_reset(us);
scsi_unlock(us_to_host(us));
us->transport_reset(us);
}
clear_bit(US_FLIDX_RESETTING, &us->dflags);
last_sector_hacks(us, srb);
}
/* Invoke the transport and basic error-handling/recovery methods
*
* This is used by the protocol layers to actually send the message to
* the device and receive the response.
*/
void usb_stor_invoke_transport(struct scsi_cmnd *srb, struct us_data *us)
{
int need_auto_sense;
int result;
/* send the command to the transport layer */
scsi_set_resid(srb, 0);
result = us->transport(srb, us);
/* if the command gets aborted by the higher layers, we need to
* short-circuit all other processing
*/
if (test_bit(US_FLIDX_TIMED_OUT, &us->dflags)) {
US_DEBUGP("-- command was aborted\n");
srb->result = DID_ABORT << 16;
goto Handle_Errors;
}
/* if there is a transport error, reset and don't auto-sense */
if (result == USB_STOR_TRANSPORT_ERROR) {
US_DEBUGP("-- transport indicates error, resetting\n");
srb->result = DID_ERROR << 16;
goto Handle_Errors;
}
/* if the transport provided its own sense data, don't auto-sense */
if (result == USB_STOR_TRANSPORT_NO_SENSE) {
srb->result = SAM_STAT_CHECK_CONDITION;
last_sector_hacks(us, srb);
return;
}
srb->result = SAM_STAT_GOOD;
/* Determine if we need to auto-sense
*
* I normally don't use a flag like this, but it's almost impossible
* to understand what's going on here if I don't.
*/
need_auto_sense = 0;
/*
* If we're running the CB transport, which is incapable
* of determining status on its own, we will auto-sense
* unless the operation involved a data-in transfer. Devices
* can signal most data-in errors by stalling the bulk-in pipe.
*/
if ((us->protocol == US_PR_CB || us->protocol == US_PR_DPCM_USB) &&
srb->sc_data_direction != DMA_FROM_DEVICE) {
US_DEBUGP("-- CB transport device requiring auto-sense\n");
need_auto_sense = 1;
}
/*
* If we have a failure, we're going to do a REQUEST_SENSE
* automatically. Note that we differentiate between a command
* "failure" and an "error" in the transport mechanism.
*/
if (result == USB_STOR_TRANSPORT_FAILED) {
US_DEBUGP("-- transport indicates command failure\n");
need_auto_sense = 1;
}
/*
* Determine if this device is SAT by seeing if the
* command executed successfully. Otherwise we'll have
* to wait for at least one CHECK_CONDITION to determine
* SANE_SENSE support
*/
if ((srb->cmnd[0] == ATA_16 || srb->cmnd[0] == ATA_12) &&
result == USB_STOR_TRANSPORT_GOOD &&
!(us->fflags & US_FL_SANE_SENSE) &&
!(srb->cmnd[2] & 0x20)) {
US_DEBUGP("-- SAT supported, increasing auto-sense\n");
us->fflags |= US_FL_SANE_SENSE;
}
/*
* A short transfer on a command where we don't expect it
* is unusual, but it doesn't mean we need to auto-sense.
*/
if ((scsi_get_resid(srb) > 0) &&
!((srb->cmnd[0] == REQUEST_SENSE) ||
(srb->cmnd[0] == INQUIRY) ||
(srb->cmnd[0] == MODE_SENSE) ||
(srb->cmnd[0] == LOG_SENSE) ||
(srb->cmnd[0] == MODE_SENSE_10))) {
US_DEBUGP("-- unexpectedly short transfer\n");
}
/* Now, if we need to do the auto-sense, let's do it */
if (need_auto_sense) {
int temp_result;
struct scsi_eh_save ses;
int sense_size = US_SENSE_SIZE;
/* device supports and needs bigger sense buffer */
if (us->fflags & US_FL_SANE_SENSE)
sense_size = ~0;
US_DEBUGP("Issuing auto-REQUEST_SENSE\n");
scsi_eh_prep_cmnd(srb, &ses, NULL, 0, sense_size);
/* FIXME: we must do the protocol translation here */
if (us->subclass == US_SC_RBC || us->subclass == US_SC_SCSI ||
us->subclass == US_SC_CYP_ATACB)
srb->cmd_len = 6;
else
srb->cmd_len = 12;
/* issue the auto-sense command */
scsi_set_resid(srb, 0);
temp_result = us->transport(us->srb, us);
/* let's clean up right away */
scsi_eh_restore_cmnd(srb, &ses);
if (test_bit(US_FLIDX_TIMED_OUT, &us->dflags)) {
US_DEBUGP("-- auto-sense aborted\n");
srb->result = DID_ABORT << 16;
goto Handle_Errors;
}
if (temp_result != USB_STOR_TRANSPORT_GOOD) {
US_DEBUGP("-- auto-sense failure\n");
/* we skip the reset if this happens to be a
* multi-target device, since failure of an
* auto-sense is perfectly valid
*/
srb->result = DID_ERROR << 16;
if (!(us->fflags & US_FL_SCM_MULT_TARG))
goto Handle_Errors;
return;
}
/* If the sense data returned is larger than 18-bytes then we
* assume this device supports requesting more in the future.
* The response code must be 70h through 73h inclusive.
*/
if (srb->sense_buffer[7] > (US_SENSE_SIZE - 8) &&
!(us->fflags & US_FL_SANE_SENSE) &&
(srb->sense_buffer[0] & 0x7C) == 0x70) {
US_DEBUGP("-- SANE_SENSE support enabled\n");
us->fflags |= US_FL_SANE_SENSE;
/* Indicate to the user that we truncated their sense
* because we didn't know it supported larger sense.
*/
US_DEBUGP("-- Sense data truncated to %i from %i\n",
US_SENSE_SIZE,
srb->sense_buffer[7] + 8);
srb->sense_buffer[7] = (US_SENSE_SIZE - 8);
}
US_DEBUGP("-- Result from auto-sense is %d\n", temp_result);
US_DEBUGP("-- code: 0x%x, key: 0x%x, ASC: 0x%x, ASCQ: 0x%x\n",
srb->sense_buffer[0],
srb->sense_buffer[2] & 0xf,
srb->sense_buffer[12],
srb->sense_buffer[13]);
#ifdef CONFIG_USB_STORAGE_DEBUG
usb_stor_show_sense(
srb->sense_buffer[2] & 0xf,
srb->sense_buffer[12],
srb->sense_buffer[13]);
#endif
/* set the result so the higher layers expect this data */
srb->result = SAM_STAT_CHECK_CONDITION;
/* If things are really okay, then let's show that. Zero
* out the sense buffer so the higher layers won't realize
* we did an unsolicited auto-sense. */
if (result == USB_STOR_TRANSPORT_GOOD &&
/* Filemark 0, ignore EOM, ILI 0, no sense */
(srb->sense_buffer[2] & 0xaf) == 0 &&
/* No ASC or ASCQ */
srb->sense_buffer[12] == 0 &&
srb->sense_buffer[13] == 0) {
srb->result = SAM_STAT_GOOD;
srb->sense_buffer[0] = 0x0;
}
}
/* Did we transfer less than the minimum amount required? */
if ((srb->result == SAM_STAT_GOOD || srb->sense_buffer[2] == 0) &&
scsi_bufflen(srb) - scsi_get_resid(srb) < srb->underflow)
srb->result = DID_ERROR << 16;
last_sector_hacks(us, srb);
return;
/* Error and abort processing: try to resynchronize with the device
* by issuing a port reset. If that fails, try a class-specific
* device reset. */
Handle_Errors:
/* Set the RESETTING bit, and clear the ABORTING bit so that
* the reset may proceed. */
scsi_lock(us_to_host(us));
set_bit(US_FLIDX_RESETTING, &us->dflags);
clear_bit(US_FLIDX_ABORTING, &us->dflags);
scsi_unlock(us_to_host(us));
/* We must release the device lock because the pre_reset routine
* will want to acquire it. */
mutex_unlock(&us->dev_mutex);
result = usb_stor_port_reset(us);
mutex_lock(&us->dev_mutex);
if (result < 0) {
scsi_lock(us_to_host(us));
usb_stor_report_device_reset(us);
scsi_unlock(us_to_host(us));
us->transport_reset(us);
}
clear_bit(US_FLIDX_RESETTING, &us->dflags);
last_sector_hacks(us, srb);
}
