static void setDefaultAspireMaps(DECLARE_ENGINE_PARAMETER_SIGNATURE) {
setFuelLoadBin(1.2, 4.4 PASS_CONFIG_PARAMETER_SUFFIX);
setFuelRpmBin(800, 7000 PASS_CONFIG_PARAMETER_SUFFIX);
setTimingLoadBin(1.2, 4.4 PASS_CONFIG_PARAMETER_SUFFIX);
setTimingRpmBin(800, 7000 PASS_CONFIG_PARAMETER_SUFFIX);
copyFuelTable(default_aspire_fuel_table, config->fuelTable);
copyTimingTable(default_aspire_timing_table, config->ignitionTable);
}
static void setDefaultCustomMaps(DECLARE_CONFIG_PARAMETER_SIGNATURE) {
setFuelLoadBin(0,100 PASS_CONFIG_PARAMETER_SUFFIX);
setFuelRpmBin(0, 7000 PASS_CONFIG_PARAMETER_SUFFIX);
setTimingLoadBin(0,100 PASS_CONFIG_PARAMETER_SUFFIX);
setTimingRpmBin(0,7000 PASS_CONFIG_PARAMETER_SUFFIX);
copyFuelTable(default_custom_fuel_table, config->fuelTable);
copyFuelTable(default_custom_fuel_table, config->veTable);
copyTimingTable(default_custom_timing_table, config->ignitionTable);
}
void setVwAba(DECLARE_ENGINE_PARAMETER_SIGNATURE) {
setCustomEngineConfiguration(PASS_ENGINE_PARAMETER_SIGNATURE);
setWholeTimingTable_d(20 PASS_CONFIG_PARAMETER_SUFFIX);
engineConfiguration->cranking.baseFuel = 12;
// set cranking_timing_angle 10
engineConfiguration->crankingTimingAngle = 10;
engineConfiguration->isCylinderCleanupEnabled = true;
// set_whole_fuel_map 12
setWholeFuelMap(12 PASS_CONFIG_PARAMETER_SUFFIX);
// set global_trigger_offset_angle 93
engineConfiguration->globalTriggerAngleOffset = 93;
setOperationMode(engineConfiguration, FOUR_STROKE_CRANK_SENSOR);
// engineConfiguration->trigger.type = TT_TOOTHED_WHEEL_60_2;
engineConfiguration->trigger.type = TT_60_2_VW;
engineConfiguration->mafAdcChannel = EFI_ADC_1;
//Base engine setting
engineConfiguration->specs.cylindersCount = 4;
engineConfiguration->specs.displacement = 2.0;
engineConfiguration->injector.flow = 320; // 30lb/h
// set algorithm 3
setAlgorithm(LM_SPEED_DENSITY PASS_CONFIG_PARAMETER_SUFFIX);
engineConfiguration->map.sensor.type = MT_GM_3_BAR;
engineConfiguration->ignitionMode = IM_ONE_COIL;
boardConfiguration->ignitionPins[0] = GPIOE_14; // Frankenso high side - pin 1G
boardConfiguration->ignitionPins[1] = GPIO_UNASSIGNED;
boardConfiguration->ignitionPins[2] = GPIO_UNASSIGNED;
boardConfiguration->ignitionPins[3] = GPIO_UNASSIGNED;
boardConfiguration->ignitionPinMode = OM_DEFAULT;
float mapRange = 110;
setEgoSensor(ES_PLX PASS_ENGINE_PARAMETER_SUFFIX);
setFuelTablesLoadBin(20, mapRange PASS_CONFIG_PARAMETER_SUFFIX);
setTimingLoadBin(20, mapRange PASS_CONFIG_PARAMETER_SUFFIX);
boardConfiguration->isSdCardEnabled = false;
engineConfiguration->tpsMin = 740;
engineConfiguration->tpsMax = 135;
}
static void setDefaultMaps(engine_configuration_s *engineConfiguration) {
setFuelLoadBin(engineConfiguration, 1.2, 4.4);
setFuelRpmBin(engineConfiguration, 800, 7000);
setTimingLoadBin(engineConfiguration, 1.2, 4.4);
setTimingRpmBin(engineConfiguration, 800, 7000);
for (int k = 0; k < FUEL_LOAD_COUNT; k++) {
for (int r = 0; r < FUEL_RPM_COUNT; r++) {
engineConfiguration->fuelTable[k][r] = default_fuel_table[k][r];
}
}
for (int k = 0; k < AD_LOAD_COUNT; k++) {
for (int r = 0; r < AD_RPM_COUNT; r++) {
engineConfiguration->ignitionTable[k][r] = default_timing_table[k][r];
}
}
}
static void setDefaultAspireMaps(engine_configuration_s *engineConfiguration) {
setFuelLoadBin(engineConfiguration, 1.2, 4.4);
setFuelRpmBin(engineConfiguration, 800, 7000);
setTimingLoadBin(engineConfiguration, 1.2, 4.4);
setTimingRpmBin(engineConfiguration, 800, 7000);
// todo: extract an array16x16 type? extract a method?
for (int k = 0; k < FUEL_LOAD_COUNT; k++) {
for (int r = 0; r < FUEL_RPM_COUNT; r++) {
engineConfiguration->fuelTable[k][r] = default_aspire_fuel_table[k][r];
}
}
// todo: extract an array16x16 type? extract a method?
for (int k = 0; k < AD_LOAD_COUNT; k++) {
for (int r = 0; r < AD_RPM_COUNT; r++) {
engineConfiguration->ignitionTable[k][r] = default_aspire_timing_table[k][r];
}
}
}
void setDodgeNeonNGCEngineConfiguration(DECLARE_ENGINE_PARAMETER_F) {
board_configuration_s * boardConfiguration = &engineConfiguration->bc;
engineConfiguration->trigger.type = TT_DODGE_NEON_2003;
setFrankenso_01_LCD(boardConfiguration);
setFrankenso0_1_joystick(engineConfiguration);
// set_global_trigger_offset_angle 50
engineConfiguration->globalTriggerAngleOffset = 50;
// set_injection_offset 0
engineConfiguration->injectionAngle = 0;
engineConfiguration->crankingInjectionMode = IM_SIMULTANEOUS;
engineConfiguration->injectionMode = IM_SEQUENTIAL;
engineConfiguration->ignitionMode = IM_WASTED_SPARK;
engineConfiguration->specs.displacement = 1.996;
engineConfiguration->specs.cylindersCount = 4;
/**
* that's NGC config
*
* set_cranking_fuel 5
*/
engineConfiguration->cranking.baseFuel = 5;
/**
* 77C
* 1200 rpm
* fuel 3
*
* 88C
* fuel 2.8
*
* set_whole_fuel_map 12
*/
//setWholeFuelMap(12 PASS_ENGINE_PARAMETER);
copyFuelTable(alphaNfuel, config->fuelTable);
//setWholeTimingTable(12 PASS_ENGINE_PARAMETER);
copyTimingTable(fromDyno, config->ignitionTable);
// set_cranking_charge_angle 70
engineConfiguration->crankingChargeAngle = 70;
// set_cranking_timing_angle 710
engineConfiguration->crankingTimingAngle = -710;
/**
* bosch 4G1139
* http://forum.2gn.org/viewtopic.php?t=21657
*/
engineConfiguration->injector.flow = 199;
// I want to start with a simple Alpha-N
engineConfiguration->algorithm = LM_ALPHA_N;
// engineConfiguration->algorithm = LM_SPEED_DENSITY;
setFuelLoadBin(0, 100 PASS_ENGINE_PARAMETER);
setTimingLoadBin(0, 100 PASS_ENGINE_PARAMETER);
boardConfiguration->malfunctionIndicatorPin = GPIO_UNASSIGNED;
/**
* PA4 Wideband O2 Sensor
*/
engineConfiguration->afr.hwChannel = EFI_ADC_4;
commonFrankensoAnalogInputs(engineConfiguration);
engineConfiguration->vbattDividerCoeff = ((float) (8.2 + 33)) / 8.2 * 2;
/**
* http://rusefi.com/wiki/index.php?title=Manual:Hardware_Frankenso_board
*/
// Frankenso low out #1: PE6 main relay
// Frankenso low out #2: PE5 alternator field control
// Frankenso low out #3: PD7 coolant fan relay
// Frankenso low out #4: PC13 idle valve solenoid
// Frankenso low out #5: PE3 fuel pump relay
// Frankenso low out #6: PE4
// Frankenso low out #7: PE1 (do not use with discovery!)
// Frankenso low out #8: PE2 injector #3
// Frankenso low out #9: PB9 injector #2
// Frankenso low out #10: PE0 (do not use with discovery!)
// Frankenso low out #11: PB8 injector #1
// Frankenso low out #12: PB7 injector #4
boardConfiguration->fanPin = GPIOD_7;
boardConfiguration->injectionPins[0] = GPIOB_8;
boardConfiguration->injectionPins[1] = GPIOB_9;
boardConfiguration->injectionPins[2] = GPIOE_2;
boardConfiguration->injectionPins[3] = GPIOB_7;
boardConfiguration->ignitionPins[0] = GPIOC_9;
boardConfiguration->ignitionPins[1] = GPIO_UNASSIGNED;
boardConfiguration->ignitionPins[2] = GPIOE_8;
boardConfiguration->ignitionPins[3] = GPIO_UNASSIGNED;
boardConfiguration->mainRelayPin = GPIOE_6;
boardConfiguration->idle.solenoidPin = GPIOC_13;
boardConfiguration->idle.solenoidFrequency = 300;
boardConfiguration->fuelPumpPin = GPIOE_3;
boardConfiguration->fuelPumpPinMode = OM_DEFAULT;
boardConfiguration->triggerInputPins[0] = GPIOA_5;
boardConfiguration->triggerInputPins[1] = GPIOC_6;
/**
* Frankenso analog #1 PC2 ADC12 CLT
* Frankenso analog #2 PC1 ADC11 IAT
* Frankenso analog #3 PA0 ADC0
* Frankenso analog #4 PC3 ADC13
* Frankenso analog #5 PA2 ADC2
* Frankenso analog #6 PA1 ADC1
* Frankenso analog #7 PA4 ADC4 WBO AFR
* Frankenso analog #8 PA3 ADC3
* Frankenso analog #9 PA7 ADC7
* Frankenso analog #10 PA6 ADC6 MAP
* Frankenso analog #11 PC5 ADC15 TPS
* Frankenso analog #12 PC4 ADC14 VBatt
*/
setThermistorConfiguration(&engineConfiguration->clt, 0, 32500, 30, 7550, 100, 700);
engineConfiguration->clt.bias_resistor = 10000;
setThermistorConfiguration(&engineConfiguration->iat, 0, 32500, 30, 7550, 100, 700);
engineConfiguration->iat.bias_resistor = 10000;
/**
* MAP PA6
*/
engineConfiguration->map.sensor.hwChannel = EFI_ADC_6;
boardConfiguration->adcHwChannelEnabled[0] = ADC_SLOW; // ADC0 - PA0
boardConfiguration->adcHwChannelEnabled[1] = ADC_SLOW; // just for test
boardConfiguration->adcHwChannelEnabled[2] = ADC_SLOW; // just for test
boardConfiguration->adcHwChannelEnabled[3] = ADC_SLOW; // just for test
boardConfiguration->adcHwChannelEnabled[4] = ADC_SLOW;
boardConfiguration->adcHwChannelEnabled[5] = ADC_OFF;
boardConfiguration->adcHwChannelEnabled[6] = ADC_FAST;
boardConfiguration->adcHwChannelEnabled[7] = ADC_SLOW; // just for test
boardConfiguration->adcHwChannelEnabled[8] = ADC_OFF;
boardConfiguration->adcHwChannelEnabled[9] = ADC_OFF;
boardConfiguration->adcHwChannelEnabled[10] = ADC_OFF;
boardConfiguration->adcHwChannelEnabled[11] = ADC_SLOW; // IAT
boardConfiguration->adcHwChannelEnabled[12] = ADC_SLOW; // CLT
boardConfiguration->adcHwChannelEnabled[13] = ADC_SLOW; // AFR
boardConfiguration->adcHwChannelEnabled[14] = ADC_SLOW; // VBatt
boardConfiguration->adcHwChannelEnabled[15] = ADC_FAST; // TPS
/**
* TPS
*/
engineConfiguration->tpsAdcChannel = EFI_ADC_15;
engineConfiguration->tpsMin = 125; // convert 12to10 bit (ADC/4)
engineConfiguration->tpsMax = 625; // convert 12to10 bit (ADC/4)
/**
* IAT D15/W7
*/
engineConfiguration->iatAdcChannel = EFI_ADC_11;
/**
* CLT D13/W9
*/
engineConfiguration->cltAdcChannel = EFI_ADC_12;
boardConfiguration->analogChartMode = AC_MAP;
boardConfiguration->isFastAdcEnabled = true;
engineConfiguration->map.sensor.type = MT_DODGE_NEON_2003;
#if EFI_HIP_9011 || defined(__DOXYGEN__)
setHip9011FrankensoPinout();
#endif
engineConfiguration->cylinderBore = 87.5;
// boardConfiguration->clutchDownPin = GPIOC_12;
boardConfiguration->clutchDownPinMode = PI_PULLUP;
boardConfiguration->clutchUpPin = GPIOD_3;
boardConfiguration->clutchUpPinMode = PI_PULLUP;
// alt GPIOC_12
/**
* set_fsio_setting 0 0.11
*/
engineConfiguration->bc.fsio_setting[0] = 0.2;
#if EFI_FSIO || defined(__DOXYGEN__)
boardConfiguration->fsio_setting[0] = 0.55;
setFsioExt(0, GPIOE_5, "0 fsio_setting", 400 PASS_ENGINE_PARAMETER);
#endif
boardConfiguration->vehicleSpeedSensorInputPin = GPIOA_8;
engineConfiguration->hasVehicleSpeedSensor = true;
engineConfiguration->fanOnTemperature = 85;
engineConfiguration->fanOffTemperature = 80;
// boardConfiguration->tunerStudioSerialSpeed = 9600;
boardConfiguration->tunerStudioSerialSpeed = 38400;
engineConfiguration->algorithm = LM_SPEED_DENSITY;
boardConfiguration->alternatorControlPin = GPIOD_5;
engineConfiguration->alternatorControlPFactor = 22;
// engineConfiguration->isCanEnabled = true;
boardConfiguration->canTxPin = GPIOB_6;
boardConfiguration->canRxPin = GPIOB_12;
engineConfiguration->canWriteEnabled = true;
engineConfiguration->canReadEnabled = false;
engineConfiguration->canNbcType = CAN_BUS_NBC_BMW;
// engineConfiguration->canNbcType = CAN_BUS_MAZDA_RX8;
boardConfiguration->idle.stepperDirectionPin = GPIOE_10;
boardConfiguration->idle.stepperStepPin = GPIOE_12;
engineConfiguration->mapAccelLength = 12;
}
/**
* @brief Global default engine configuration
* This method sets the global engine configuration defaults. These default values are then
* overridden by engine-specific defaults and the settings are saved in flash memory.
*
* This method is invoked only when new configuration is needed:
* * recently re-flashed chip
* * flash version of configuration failed CRC check or appears to be older then FLASH_DATA_VERSION
* * 'rewriteconfig' command
* * 'set_engine_type X' command
*/
void setDefaultConfiguration(DECLARE_ENGINE_PARAMETER_F) {
#if (! EFI_UNIT_TEST) || defined(__DOXYGEN__)
memset(&persistentState.persistentConfiguration, 0, sizeof(persistentState.persistentConfiguration));
#endif
prepareVoidConfiguration(engineConfiguration);
boardConfiguration->mafSensorType = Bosch0280218037;
setBosch0280218037(config);
engineConfiguration->injector.lag = 1.0;
engineConfiguration->acCutoffLowRpm = 700;
engineConfiguration->acCutoffHighRpm = 5000;
initTemperatureCurve(IAT_CURVE_SIZE, config->iatFuelCorrBins, config->iatFuelCorr);
initTemperatureCurve(CLT_CURVE_SIZE, config->cltFuelCorrBins, config->cltFuelCorr);
initTemperatureCurve(CLT_CURVE_SIZE, config->cltIdleCorrBins, config->cltIdleCorr);
engineConfiguration->tachPulseDuractionMs = 4;
engineConfiguration->tachPulseTriggerIndex = 4;
setTableValue(config->cltIdleCorrBins, config->cltIdleCorr, CLT_CURVE_SIZE, -40, 1.5);
setTableValue(config->cltIdleCorrBins, config->cltIdleCorr, CLT_CURVE_SIZE, -30, 1.5);
setTableValue(config->cltIdleCorrBins, config->cltIdleCorr, CLT_CURVE_SIZE, -20, 1.42);
setTableValue(config->cltIdleCorrBins, config->cltIdleCorr, CLT_CURVE_SIZE, -10, 1.36);
setTableValue(config->cltIdleCorrBins, config->cltIdleCorr, CLT_CURVE_SIZE, 0, 1.28);
setTableValue(config->cltIdleCorrBins, config->cltIdleCorr, CLT_CURVE_SIZE, 10, 1.19);
setTableValue(config->cltIdleCorrBins, config->cltIdleCorr, CLT_CURVE_SIZE, 20, 1.12);
setTableValue(config->cltIdleCorrBins, config->cltIdleCorr, CLT_CURVE_SIZE, 30, 1.10);
setTableValue(config->cltIdleCorrBins, config->cltIdleCorr, CLT_CURVE_SIZE, 40, 1.06);
setTableValue(config->cltIdleCorrBins, config->cltIdleCorr, CLT_CURVE_SIZE, 50, 1.06);
setTableValue(config->cltIdleCorrBins, config->cltIdleCorr, CLT_CURVE_SIZE, 60, 1.03);
setTableValue(config->cltIdleCorrBins, config->cltIdleCorr, CLT_CURVE_SIZE, 70, 1.01);
setTableValue(config->cltFuelCorrBins, config->cltFuelCorr, CLT_CURVE_SIZE, -40, 1.5);
setTableValue(config->cltFuelCorrBins, config->cltFuelCorr, CLT_CURVE_SIZE, -30, 1.5);
setTableValue(config->cltFuelCorrBins, config->cltFuelCorr, CLT_CURVE_SIZE, -20, 1.42);
setTableValue(config->cltFuelCorrBins, config->cltFuelCorr, CLT_CURVE_SIZE, -10, 1.36);
setTableValue(config->cltFuelCorrBins, config->cltFuelCorr, CLT_CURVE_SIZE, 0, 1.28);
setTableValue(config->cltFuelCorrBins, config->cltFuelCorr, CLT_CURVE_SIZE, 10, 1.19);
setTableValue(config->cltFuelCorrBins, config->cltFuelCorr, CLT_CURVE_SIZE, 20, 1.12);
setTableValue(config->cltFuelCorrBins, config->cltFuelCorr, CLT_CURVE_SIZE, 30, 1.10);
setTableValue(config->cltFuelCorrBins, config->cltFuelCorr, CLT_CURVE_SIZE, 40, 1.06);
setTableValue(config->cltFuelCorrBins, config->cltFuelCorr, CLT_CURVE_SIZE, 50, 1.06);
setTableValue(config->cltFuelCorrBins, config->cltFuelCorr, CLT_CURVE_SIZE, 60, 1.03);
setTableValue(config->cltFuelCorrBins, config->cltFuelCorr, CLT_CURVE_SIZE, 70, 1.01);
for (int i = 0; i < VBAT_INJECTOR_CURVE_SIZE; i++) {
engineConfiguration->injector.battLagCorrBins[i] = 12 - VBAT_INJECTOR_CURVE_SIZE / 2 + i;
engineConfiguration->injector.battLagCorr[i] = 0; // zero extra time by default
}
setConstantDwell(4 PASS_ENGINE_PARAMETER); // 4ms is global default dwell
engineConfiguration->useConstantDwellDuringCranking = false;
setFuelLoadBin(1.2, 4.4 PASS_ENGINE_PARAMETER);
setFuelRpmBin(800, 7000 PASS_ENGINE_PARAMETER);
setTimingLoadBin(1.2, 4.4 PASS_ENGINE_PARAMETER);
setTimingRpmBin(800, 7000 PASS_ENGINE_PARAMETER);
setTableBin2(engineConfiguration->map.samplingAngleBins, MAP_ANGLE_SIZE, 800, 7000, 1);
setTableBin2(engineConfiguration->map.samplingAngle, MAP_ANGLE_SIZE, 100, 130, 1);
setTableBin2(engineConfiguration->map.samplingWindowBins, MAP_ANGLE_SIZE, 800, 7000, 1);
setTableBin2(engineConfiguration->map.samplingWindow, MAP_ANGLE_SIZE, 50, 50, 1);
// set_whole_timing_map 3
setWholeFuelMap(3 PASS_ENGINE_PARAMETER);
setMap(config->afrTable, 14.7);
setDefaultVETable(PASS_ENGINE_PARAMETER_F);
setMap(config->injectionPhase, -180);
setRpmTableBin(config->injPhaseRpmBins, FUEL_RPM_COUNT);
setFuelTablesLoadBin(10, 160 PASS_ENGINE_PARAMETER);
setDefaultIatTimingCorrection(PASS_ENGINE_PARAMETER_F);
setThermistorConfiguration(&engineConfiguration->clt, 0, 9500, 23.8889, 2100, 48.8889, 1000);
engineConfiguration->clt.config.bias_resistor = 1500;
setThermistorConfiguration(&engineConfiguration->iat, 32, 9500, 75, 2100, 120, 1000);
// todo: this value is way off! I am pretty sure temp coeffs are off also
engineConfiguration->iat.config.bias_resistor = 2700;
engineConfiguration->step1rpm = 3000;
engineConfiguration->step1timing = 10;
engineConfiguration->step1RpmWindow = 500;
engineConfiguration->step1fuelCutEnable = false;
engineConfiguration->step1SparkCutEnable = false;
engineConfiguration->step1RpmWindow = 500;
engineConfiguration->rpmHardLimit = 7000;
engineConfiguration->cranking.rpm = 550;
engineConfiguration->cutFuelOnHardLimit = true;
engineConfiguration->cutSparkOnHardLimit = true;
engineConfiguration->noAccelAfterHardLimitPeriodSecs = 3;
setTableBin2(engineConfiguration->crankingTpsCoef, CRANKING_CURVE_SIZE, 1, 1, 1);
setTableBin2(engineConfiguration->crankingTpsBins, CRANKING_CURVE_SIZE, 0, 100, 1);
config->crankingFuelCoef[0] = 5; // base cranking fuel adjustment coefficient
config->crankingFuelBins[0] = -20; // temperature in C
config->crankingFuelCoef[1] = 3.7;
config->crankingFuelBins[1] = -10;
config->crankingFuelCoef[2] = 2.6;
config->crankingFuelBins[2] = 5;
config->crankingFuelCoef[3] = 2.4;
config->crankingFuelBins[3] = 20;
config->crankingFuelCoef[4] = 2.1;
config->crankingFuelBins[4] = 35;
config->crankingFuelCoef[5] = 1.8;
config->crankingFuelBins[5] = 50;
config->crankingFuelCoef[6] = 1.5;
config->crankingFuelBins[6] = 65;
config->crankingFuelCoef[7] = 1;
config->crankingFuelBins[7] = 90;
config->crankingCycleCoef[0] = 2;
config->crankingCycleBins[0] = 10;
config->crankingCycleCoef[1] = 1;
config->crankingCycleBins[1] = 31;
config->crankingCycleCoef[2] = 1;
config->crankingCycleBins[2] = 52;
config->crankingCycleCoef[3] = 0.5;
config->crankingCycleBins[3] = 73;
config->crankingCycleCoef[4] = 0.5;
config->crankingCycleBins[4] = 74;
config->crankingCycleCoef[5] = 0.5;
config->crankingCycleBins[5] = 75;
config->crankingCycleCoef[6] = 0.5;
config->crankingCycleBins[6] = 76;
config->crankingCycleCoef[7] = 0.5;
config->crankingCycleBins[7] = 77;
engineConfiguration->cranking.baseFuel = 5;
engineConfiguration->analogInputDividerCoefficient = 2;
engineConfiguration->crankingChargeAngle = 70;
engineConfiguration->timingMode = TM_DYNAMIC;
engineConfiguration->fixedModeTiming = 50;
// performance optimization
boardConfiguration->sensorChartMode = SC_OFF;
engineConfiguration->map.sensor.hwChannel = EFI_ADC_4;
engineConfiguration->baroSensor.hwChannel = EFI_ADC_NONE;
engineConfiguration->pedalPositionChannel = EFI_ADC_NONE;
engineConfiguration->specs.firingOrder = FO_1_THEN_3_THEN_4_THEN2;
engineConfiguration->crankingInjectionMode = IM_SIMULTANEOUS;
engineConfiguration->injectionMode = IM_SEQUENTIAL;
engineConfiguration->ignitionMode = IM_ONE_COIL;
engineConfiguration->globalTriggerAngleOffset = 0;
engineConfiguration->injectionOffset = 0;
engineConfiguration->ignitionOffset = 0;
engineConfiguration->overrideCrankingIgnition = true;
engineConfiguration->sensorChartFrequency = 20;
engineConfiguration->algorithm = LM_PLAIN_MAF;
engineConfiguration->vbattDividerCoeff = ((float) (15 + 65)) / 15;
engineConfiguration->fanOnTemperature = 75;
engineConfiguration->fanOffTemperature = 70;
engineConfiguration->tpsMin = convertVoltageTo10bitADC(1.250);
engineConfiguration->tpsMax = convertVoltageTo10bitADC(4.538);
engineConfiguration->tpsErrorLowValue = convertVoltageTo10bitADC(0.2);
engineConfiguration->tpsErrorHighValue = convertVoltageTo10bitADC(6);
engineConfiguration->canNbcType = CAN_BUS_NBC_BMW;
engineConfiguration->canSleepPeriod = 50;
engineConfiguration->canReadEnabled = true;
engineConfiguration->canWriteEnabled = false;
setOperationMode(engineConfiguration, FOUR_STROKE_CAM_SENSOR);
engineConfiguration->specs.cylindersCount = 4;
engineConfiguration->specs.displacement = 2;
/**
* By the way http://users.erols.com/srweiss/tableifc.htm has a LOT of data
*/
engineConfiguration->injector.flow = 200;
engineConfiguration->displayMode = DM_HD44780;
engineConfiguration->logFormat = LF_NATIVE;
engineConfiguration->directSelfStimulation = false;
engineConfiguration->trigger.type = TT_TOOTHED_WHEEL_60_2;
engineConfiguration->HD44780width = 20;
engineConfiguration->HD44780height = 4;
engineConfiguration->vRefAdcChannel = EFI_ADC_NONE;
engineConfiguration->vbattAdcChannel = EFI_ADC_NONE;
engineConfiguration->clt.adcChannel = EFI_ADC_6;
engineConfiguration->iat.adcChannel = EFI_ADC_7;
engineConfiguration->mafAdcChannel = EFI_ADC_NONE;
engineConfiguration->afr.hwChannel = EFI_ADC_14;
engineConfiguration->cylinderBore = 87.5;
setEgoSensor(ES_14Point7_Free PASS_ENGINE_PARAMETER);
engineConfiguration->globalFuelCorrection = 1;
engineConfiguration->map.sensor.type = MT_MPX4250;
engineConfiguration->baroSensor.type = MT_CUSTOM;
engineConfiguration->baroSensor.valueAt0 = 0;
engineConfiguration->baroSensor.valueAt5 = 500;
engineConfiguration->hasMapSensor = true;
engineConfiguration->hasMafSensor = true;
engineConfiguration->hasTpsSensor = true;
engineConfiguration->hasAfrSensor = true;
engineConfiguration->hasIatSensor = true;
engineConfiguration->hasCltSensor = true;
engineConfiguration->hasBaroSensor = false;
engineConfiguration->isEngineChartEnabled = true;
engineConfiguration->useOnlyFrontForTrigger = false;
boardConfiguration->idle.solenoidFrequency = 200;
// set_idle_position 50
boardConfiguration->idlePosition = 50;
engineConfiguration->targetIdleRpm = 1200;
// engineConfiguration->idleMode = IM_AUTO;
engineConfiguration->idleMode = IM_MANUAL;
engineConfiguration->acSwitchAdc = EFI_ADC_NONE;
engineConfiguration->externalKnockSenseAdc = EFI_ADC_NONE;
boardConfiguration->useSerialPort = true;
boardConfiguration->useStepperIdle = false;
boardConfiguration->idle.stepperDirectionPin = GPIOE_10;
boardConfiguration->idle.stepperStepPin = GPIOE_12;
engineConfiguration->stepperEnablePin = GPIOE_14;
engineConfiguration->idleStepperReactionTime = 10;
engineConfiguration->idleStepperTotalSteps = 150;
#if EFI_PROD_CODE || defined(__DOXYGEN__)
engineConfiguration->engineChartSize = 300;
#else
// need more events for automated test
engineConfiguration->engineChartSize = 400;
#endif
engineConfiguration->engineCycle = 720;
engineConfiguration->primingSquirtDurationMs = 5;
engineConfiguration->isInjectionEnabled = true;
engineConfiguration->isIgnitionEnabled = true;
engineConfiguration->isCylinderCleanupEnabled = true;
engineConfiguration->secondTriggerChannelEnabled = true;
engineConfiguration->isMapAveragingEnabled = true;
engineConfiguration->isMilEnabled = true;
engineConfiguration->isFuelPumpEnabled = true;
engineConfiguration->isTunerStudioEnabled = true;
engineConfiguration->isWaveAnalyzerEnabled = true;
engineConfiguration->isIdleThreadEnabled = true;
engineConfiguration->acIdleRpmBump = 200;
engineConfiguration->knockDetectionWindowStart = 35;
engineConfiguration->knockDetectionWindowEnd = 135;
engineConfiguration->fuelLevelSensor = EFI_ADC_NONE;
boardConfiguration->fuelLevelEmptyTankVoltage = 0;
boardConfiguration->fuelLevelFullTankVoltage = 5;
engineConfiguration->hipOutputChannel = EFI_ADC_NONE;
/**
* this is RPM. 10000 rpm is only 166Hz, 800 rpm is 13Hz
*/
boardConfiguration->triggerSimulatorFrequency = 1200;
boardConfiguration->triggerErrorPin = GPIO_UNASSIGNED;
boardConfiguration->max31855spiDevice = SPI_NONE;
for (int i = 0; i < EGT_CHANNEL_COUNT; i++) {
boardConfiguration->max31855_cs[i] = GPIO_UNASSIGNED;
}
for (int i = 0; i < LE_COMMAND_COUNT; i++) {
boardConfiguration->fsioPins[i] = GPIO_UNASSIGNED;
config->le_formulas[i][0] = 0;
boardConfiguration->fsioDigitalInputs[i] = GPIO_UNASSIGNED;
engineConfiguration->fsioInputModes[i] = PI_DEFAULT;
}
boardConfiguration->triggerSimulatorPins[0] = GPIOD_1;
boardConfiguration->triggerSimulatorPins[1] = GPIOD_2;
boardConfiguration->triggerSimulatorPins[2] = GPIO_UNASSIGNED;
boardConfiguration->triggerSimulatorPinModes[0] = OM_DEFAULT;
boardConfiguration->triggerSimulatorPinModes[1] = OM_DEFAULT;
boardConfiguration->triggerSimulatorPinModes[2] = OM_DEFAULT;
setFrankenstein_01_LCD(boardConfiguration);
strcpy(config->timingMultiplier, "1");
strcpy(config->timingAdditive, "0");
engineConfiguration->hip9011SpiDevice = SPI_DEVICE_2;
engineConfiguration->isAlternatorControlEnabled = true;
engineConfiguration->isGpsEnabled = false;
boardConfiguration->gps_rx_pin = GPIOB_7;
boardConfiguration->gps_tx_pin = GPIOB_6;
boardConfiguration->triggerInputPins[0] = GPIOC_6;
boardConfiguration->triggerInputPins[1] = GPIOA_5;
boardConfiguration->logicAnalyzerPins[0] = GPIO_UNASSIGNED;
boardConfiguration->logicAnalyzerPins[1] = GPIO_UNASSIGNED; // GPIOE_5 is a popular option (if available)
boardConfiguration->logicAnalyzerPins[2] = GPIO_UNASSIGNED;
boardConfiguration->logicAnalyzerPins[3] = GPIO_UNASSIGNED;
boardConfiguration->vehicleSpeedSensorInputPin = GPIO_UNASSIGNED;
engineConfiguration->vehicleSpeedCoef = 1.0f;
boardConfiguration->logicAnalyzerMode[0] = false;
boardConfiguration->logicAnalyzerMode[1] = false;
engineConfiguration->mapErrorLowValue = 5;
engineConfiguration->mapErrorHighValue = 250;
boardConfiguration->idleThreadPeriod = 100;
boardConfiguration->consoleLoopPeriod = 200;
boardConfiguration->lcdThreadPeriod = 300;
boardConfiguration->generalPeriodicThreadPeriod = 50;
boardConfiguration->useLcdScreen = true;
boardConfiguration->boardTestModeJumperPin = GPIOB_0;
boardConfiguration->canDeviceMode = CD_USE_CAN2;
boardConfiguration->canTxPin = GPIOB_6;
boardConfiguration->canRxPin = GPIOB_12;
// set this to SPI_DEVICE_3 to enable stimulation
boardConfiguration->digitalPotentiometerSpiDevice = SPI_NONE;
boardConfiguration->digitalPotentiometerChipSelect[0] = GPIOD_7;
boardConfiguration->digitalPotentiometerChipSelect[1] = GPIO_UNASSIGNED;
boardConfiguration->digitalPotentiometerChipSelect[2] = GPIOD_5;
boardConfiguration->digitalPotentiometerChipSelect[3] = GPIO_UNASSIGNED;
boardConfiguration->is_enabled_spi_1 = false;
boardConfiguration->is_enabled_spi_2 = false;
boardConfiguration->is_enabled_spi_3 = true;
boardConfiguration->spi1mosiPin = GPIOB_5;
boardConfiguration->spi1misoPin = GPIOB_4;
boardConfiguration->spi1sckPin = GPIOB_3; // please note that this pin is also SWO/SWD - Single Wire debug Output
boardConfiguration->spi2mosiPin = GPIOB_15;
boardConfiguration->spi2misoPin = GPIOB_14;
boardConfiguration->spi2sckPin = GPIOB_13;
boardConfiguration->spi3mosiPin = GPIOB_5;
boardConfiguration->spi3misoPin = GPIOB_4;
boardConfiguration->spi3sckPin = GPIOB_3;
boardConfiguration->hip9011Gain = 1;
boardConfiguration->sdCardCsPin = GPIOD_4;
boardConfiguration->isSdCardEnabled = true;
boardConfiguration->isFastAdcEnabled = true;
boardConfiguration->isEngineControlEnabled = true;
boardConfiguration->isVerboseAlternator = false;
boardConfiguration->tunerStudioSerialSpeed = TS_DEFAULT_SPEED;
engineConfiguration->mapAccelLength = 6;
engineConfiguration->mapAccelEnrichmentThreshold = 5; // kPa
engineConfiguration->mapAccelEnrichmentMultiplier = 2;
engineConfiguration->tpsAccelLength = 12;
engineConfiguration->tpsAccelEnrichmentThreshold = 40; // TPS % change, per engine cycle
engineConfiguration->tpsAccelEnrichmentMultiplier = 0.05;
}
void setDodgeNeonNGCEngineConfiguration(engine_configuration_s *engineConfiguration,
board_configuration_s *boardConfiguration) {
engineConfiguration->triggerConfig.triggerType = TT_DODGE_NEON_2003;
setFrankenso_01_LCD(boardConfiguration);
// set_global_trigger_offset_angle 46
engineConfiguration->globalTriggerAngleOffset = 46;
engineConfiguration->needSecondTriggerInput = false;
engineConfiguration->crankingInjectionMode = IM_SIMULTANEOUS;
engineConfiguration->injectionMode = IM_SEQUENTIAL;
engineConfiguration->ignitionMode = IM_WASTED_SPARK;
engineConfiguration->displacement = 1.996;
engineConfiguration->cylindersCount = 4;
/**
* that's NGC config
*
* set_cranking_fuel 5
*/
engineConfiguration->crankingSettings.baseCrankingFuel = 5;
/**
* 77C
* 1200 rpm
* fuel 3
*
* 88C
* fuel 2.8
*
* set_whole_fuel_map 12
*/
setWholeFuelMap(engineConfiguration, 12);
setWholeTimingTable(engineConfiguration, 12);
// set_cranking_charge_angle 70
engineConfiguration->crankingChargeAngle = 70;
// set_cranking_timing_angle 710
engineConfiguration->crankingTimingAngle = 710;
/**
* bosch 4G1139
* http://forum.2gn.org/viewtopic.php?t=21657
*/
engineConfiguration->injectorFlow = 199;
// I want to start with a simple Alpha-N
engineConfiguration->algorithm = LM_ALPHA_N;
setFuelLoadBin(engineConfiguration, 0, 100);
setTimingLoadBin(engineConfiguration, 0, 100);
boardConfiguration->malfunctionIndicatorPin = GPIO_UNASSIGNED;
/**
* PA4 Wideband O2 Sensor
*/
engineConfiguration->afrSensor.afrAdcChannel = EFI_ADC_4;
commonFrankensoAnalogInputs(engineConfiguration);
engineConfiguration->vbattDividerCoeff = ((float) (8.2 + 33)) / 8.2 * 2;
// Frankenso low out #1: PE6
// Frankenso low out #2: PE5
// Frankenso low out #3: PD7 coolant fan relay
// Frankenso low out #4: PC13 idle valve solenoid
// Frankenso low out #5: PE3 fuel pump relay
// Frankenso low out #6: PE4
// Frankenso low out #7: PE1 (do not use with discovery!)
// Frankenso low out #8: PE2 injector #3
// Frankenso low out #9: PB9 injector #2
// Frankenso low out #10: PE0 (do not use with discovery!)
// Frankenso low out #11: PB8 injector #1
// Frankenso low out #12: PB7 injector #4
boardConfiguration->fanPin = GPIOD_7;
boardConfiguration->injectionPins[0] = GPIOB_8;
boardConfiguration->injectionPins[1] = GPIOB_9;
boardConfiguration->injectionPins[2] = GPIOE_2;
boardConfiguration->injectionPins[3] = GPIOB_7;
boardConfiguration->ignitionPins[0] = GPIOC_9;
boardConfiguration->ignitionPins[1] = GPIO_UNASSIGNED;
boardConfiguration->ignitionPins[2] = GPIOE_8;
boardConfiguration->ignitionPins[3] = GPIO_UNASSIGNED;
boardConfiguration->idleValvePin = GPIOC_13;
boardConfiguration->idleSolenoidFrequency = 300;
boardConfiguration->fuelPumpPin = GPIOE_3;
boardConfiguration->fuelPumpPinMode = OM_DEFAULT;
boardConfiguration->gps_rx_pin = GPIO_UNASSIGNED;
boardConfiguration->gps_tx_pin = GPIO_UNASSIGNED;
boardConfiguration->triggerInputPins[0] = GPIOA_5;
boardConfiguration->triggerInputPins[1] = GPIOC_6;
setThermistorConfiguration(&engineConfiguration->cltThermistorConf, 0, 32500, 30, 7550, 100, 700);
engineConfiguration->cltThermistorConf.bias_resistor = 10000;
setThermistorConfiguration(&engineConfiguration->iatThermistorConf, 0, 32500, 30, 7550, 100, 700);
engineConfiguration->iatThermistorConf.bias_resistor = 10000;
/**
* MAP PA6
*/
engineConfiguration->map.sensor.hwChannel = EFI_ADC_6;
boardConfiguration->adcHwChannelEnabled[0] = ADC_FAST; // ADC0 - PA0 - MAP
boardConfiguration->adcHwChannelEnabled[1] = ADC_SLOW;
boardConfiguration->adcHwChannelEnabled[4] = ADC_SLOW;
boardConfiguration->adcHwChannelEnabled[11] = ADC_SLOW; // IAT
boardConfiguration->adcHwChannelEnabled[12] = ADC_SLOW; // CLT
boardConfiguration->adcHwChannelEnabled[13] = ADC_SLOW; // AFR
boardConfiguration->adcHwChannelEnabled[14] = ADC_SLOW; // VBatt
boardConfiguration->adcHwChannelEnabled[15] = ADC_SLOW; // TPS
/**
* TPS
*/
engineConfiguration->tpsAdcChannel = EFI_ADC_15;
engineConfiguration->tpsMin = 125; // convert 12to10 bit (ADC/4)
engineConfiguration->tpsMax = 625; // convert 12to10 bit (ADC/4)
/**
* IAT D15/W7
*/
engineConfiguration->iatAdcChannel = EFI_ADC_11;
/**
* CLT D13/W9
*/
engineConfiguration->cltAdcChannel = EFI_ADC_12;
}
static void setHondaAccordConfigurationCommon(engine_configuration_s *engineConfiguration, board_configuration_s *boardConfiguration) {
engineConfiguration->map.sensor.sensorType = MT_DENSO183;
engineConfiguration->ignitionMode = IM_ONE_COIL;
engineConfiguration->injectionMode = IM_BATCH;
engineConfiguration->idleMode = IM_MANUAL;
engineConfiguration->HD44780height = 4;
engineConfiguration->cylindersCount = 4;
engineConfiguration->displacement = 2.156;
// Keihin 06164-P0A-A00
engineConfiguration->injectorFlow = 248;
// engineConfiguration->algorithm = LM_SPEED_DENSITY;
// I want to start with a simple Alpha-N
engineConfiguration->algorithm = LM_TPS;
setFuelLoadBin(engineConfiguration, 0, 100);
setTimingLoadBin(engineConfiguration, 0, 100);
engineConfiguration->crankingSettings.coolantTempMaxC = 65; // 8ms at 65C
engineConfiguration->crankingSettings.fuelAtMaxTempMs = 8;
engineConfiguration->crankingSettings.coolantTempMinC = 0; // 20ms at 0C
engineConfiguration->crankingSettings.fuelAtMinTempMs = 15;
/**
* 18K Ohm @ -20C
* 2.1K Ohm @ 24C
* 100 Ohm @ 120C
*/
setThermistorConfiguration(&engineConfiguration->cltThermistorConf, -20.0, 18000.0, 23.8889, 2100.0, 120.0, 100.0);
engineConfiguration->cltThermistorConf.bias_resistor = 1500; // same as OEM ECU
setThermistorConfiguration(&engineConfiguration->iatThermistorConf, -20.0, 18000.0, 23.8889, 2100.0, 120.0, 100.0);
engineConfiguration->iatThermistorConf.bias_resistor = 1500; // same as OEM ECU
// set_cranking_charge_angle 35
engineConfiguration->crankingChargeAngle = 70;
// set_cranking_timing_angle 0
engineConfiguration->crankingTimingAngle = 45;
// set_global_trigger_offset_angle 34
engineConfiguration->globalTriggerAngleOffset = 34;
// set_rpm_hard_limit 4000
engineConfiguration->rpmHardLimit = 4000; // yes, 4k. let's play it safe for now
// set_cranking_rpm 2000
engineConfiguration->crankingSettings.crankingRpm = 500;
// set_ignition_offset 350
// engineConfiguration->ignitionOffset = 350;
// set_injection_offset 510
// engineConfiguration->injectionOffset = 510;
/**
* ADC inputs:
*
* Inp1/ADC12 PC2: CLT
* Inp2/ADC11 PC1: AIT/IAT
* Inp3/ADC0 PA0: MAP
* Inp4/ADC13 PC3: AFR
* Inp6/ADC1 PA1: TPS
* Inp12/ADC14 PC4: VBatt
*/
memset(boardConfiguration->adcHwChannelEnabled, 0, sizeof(boardConfiguration->adcHwChannelEnabled));
boardConfiguration->adcHwChannelEnabled[0] = ADC_FAST; // ADC0 - PA0 - MAP
boardConfiguration->adcHwChannelEnabled[1] = ADC_SLOW; // TPS
boardConfiguration->adcHwChannelEnabled[2] = ADC_SLOW;
boardConfiguration->adcHwChannelEnabled[3] = ADC_SLOW;
boardConfiguration->adcHwChannelEnabled[4] = ADC_SLOW;
boardConfiguration->adcHwChannelEnabled[6] = ADC_SLOW;
boardConfiguration->adcHwChannelEnabled[11] = ADC_SLOW; // IAT
boardConfiguration->adcHwChannelEnabled[12] = ADC_SLOW; // CLT
boardConfiguration->adcHwChannelEnabled[13] = ADC_SLOW; // AFR
boardConfiguration->adcHwChannelEnabled[14] = ADC_SLOW; // VBatt
/**
* D14/W10 O2 Sensor
*/
engineConfiguration->afrSensor.afrAdcChannel = EFI_ADC_13;
/**
* VBatt
*/
engineConfiguration->vbattAdcChannel = EFI_ADC_14;
engineConfiguration->vbattDividerCoeff = ((float) (8.2 + 33)) / 8.2 * 2;
// todo engineConfiguration->afrSensor.afrAdcChannel = 14;
/**
* MAP D17/W5
*/
engineConfiguration->map.sensor.hwChannel = EFI_ADC_0;
/**
* TPS D11/W11
*/
engineConfiguration->tpsAdcChannel = EFI_ADC_1;
/**
* IAT D15/W7
*/
engineConfiguration->iatAdcChannel = EFI_ADC_11;
/**
* CLT D13/W9
*/
engineConfiguration->cltAdcChannel = EFI_ADC_12;
/**
* Outputs
*/
// Frankenso low out #:
// Frankenso low out #:
// Frankenso low out #:
// Frankenso low out #:
// Frankenso low out #5: PE3
// Frankenso low out #6: PE4
// Frankenso low out #7: PE1 (do not use with discovery!)
// Frankenso low out #:
// Frankenso low out #9: PB9
// Frankenso low out #10: PE0 (do not use with discovery!)
// Frankenso low out #11: PB8
// Frankenso low out #12: PB7
boardConfiguration->idleValvePin = GPIOE_5;
boardConfiguration->o2heaterPin = GPIOC_13;
boardConfiguration->injectionPins[0] = GPIOB_8;
boardConfiguration->injectionPins[1] = GPIOB_9;
boardConfiguration->injectionPins[2] = GPIOE_1;
boardConfiguration->injectionPins[3] = GPIOB_7;
boardConfiguration->ignitionPins[0] = GPIOE_4;
boardConfiguration->ignitionPins[1] = GPIO_NONE;
boardConfiguration->ignitionPins[2] = GPIO_NONE;
boardConfiguration->ignitionPins[3] = GPIO_NONE;
boardConfiguration->fuelPumpPin = GPIOE_3;
boardConfiguration->fuelPumpPinMode = OM_DEFAULT;
boardConfiguration->gps_rx_pin = GPIO_NONE;
boardConfiguration->gps_tx_pin = GPIO_NONE;
setFrankenso_01_LCD(boardConfiguration);
boardConfiguration->logicAnalyzerPins[1] = GPIO_NONE;
boardConfiguration->idleSolenoidFrequency = 500;
}
