C++ (Cpp) slow_mode_test Examples

Example #1

File: main.c Project: quark-mcu/qmsi

int main(void)
{
	qm_rtc_config_t rtc_cfg;
	unsigned int count = 0;
	/* loop_max : Maximum number of iterations.
	 * A value of 50 will run the application for roughly 30s.
	 */
	const unsigned int loop_max = 50;
	gpio_init();
	pin_mux_setup();
	gpio_set_out(BOARD_LED_PIN, 0); /* Configure the onboard LED pin. */

	/* Clear Screen. */
	QM_PUTS("Starting: Power Profiler");
	QM_PUTS("Low power mode example.");
	QM_PRINTF("Increment = %d\n", QM_RTC_ALARM_SECOND(CLK_RTC_DIV_1));

	clk_periph_enable(CLK_PERIPH_RTC_REGISTER | CLK_PERIPH_CLK);

	/* Initialise RTC configuration: Run, but don't interrupt. */
	rtc_cfg.init_val = 0;
	rtc_cfg.alarm_en = 0;
	rtc_cfg.alarm_val = QM_RTC_ALARM_SECOND(CLK_RTC_DIV_1);
	rtc_cfg.callback = rtc_example_callback;
	rtc_cfg.prescaler = CLK_RTC_DIV_1;
	qm_rtc_set_config(QM_RTC_0, &rtc_cfg);

	QM_IR_UNMASK_INT(QM_IRQ_RTC_0_INT);
	QM_IRQ_REQUEST(QM_IRQ_RTC_0_INT, qm_rtc_0_isr);

#if (!QM_SENSOR)
	test_clock_rates();
#endif

	/* Enable the RTC Interrupt. */
	rtc_cfg.alarm_en = 1;
	qm_rtc_set_config(QM_RTC_0, &rtc_cfg);

	count = 0;
	while (++count < loop_max) {
		QM_PRINTF("\nC:%d R:%d => ", count, rtc_tick);

		slow_mode_test();
		halt_test();
		core_sleep_test();
		/* TODO : Enable soc_sleep test for c1000. */
		soc_sleep_test();
		/* TODO : Enable soc_deep_sleep test for d2000 and c1000. */
		soc_deep_sleep_test();
	}
	SOC_WATCH_TRIGGER_FLUSH();
	QM_PUTS("Finished: Power Profiler");
	return 0;
}

Example #2

File: main.c Project: jeez/qmsi

int main(void)
{
	qm_rtc_config_t rtc_cfg;
	unsigned int count = 0;
	/* Maximum number of 3-second iterations. */
	const unsigned int loop_max = 5;
	gpio_init();
	gpio_set_out(BOARD_LED_PIN, 0); /* Configure the onboard LED pin. */

	/* Clear Screen. */
	QM_PUTS("Starting: Power Profiler");
	QM_PUTS("Low power mode example.");
	QM_PRINTF("Increment = %d\n", QM_RTC_ALARM_SECOND(CLK_RTC_DIV_1));

	clk_periph_enable(CLK_PERIPH_RTC_REGISTER | CLK_PERIPH_CLK);

	/* Initialise RTC configuration: Run, but don't interrupt. */
	rtc_cfg.init_val = 0;
	rtc_cfg.alarm_en = 0;
	rtc_cfg.alarm_val = QM_RTC_ALARM_SECOND(CLK_RTC_DIV_1);
	rtc_cfg.callback = rtc_example_callback;
	rtc_cfg.prescaler = CLK_RTC_DIV_1;
	qm_rtc_set_config(QM_RTC_0, &rtc_cfg);

	qm_irq_request(QM_IRQ_RTC_0_INT, qm_rtc_0_isr);

	test_clock_rates();

	/* Enable the RTC Interrupt. */
	rtc_cfg.alarm_en = 1;
	qm_rtc_set_config(QM_RTC_0, &rtc_cfg);

	count = 0;
	while (++count < loop_max) {
		QM_PRINTF("\nC:%d R:%d => ", count, rtc_tick);

		slow_mode_test();
		halt_test();
		sleep_test();
#if DEEP_SLEEP
		deep_sleep_test();
#endif
	}
	QM_PUTS("Finished: Power Profiler");
	return 0;
}

Example #3

File: pc7210_cmd_pm.c Project: channinglan/BootLoader

extern void 
socle_cmd_power_manage ()
{
	int ch;
    
	while(1){		
		printf("=========================\n");		
		printf("Power Management Test\n");
		printf("0.Stop mode test\n");
		printf("1.Sleep mode test\n");
		printf("2.Slow mode test\n");
		printf("3.IP/PHY clock test\n");
		printf("4.Test mode test (Disable all IP clock except sdram)\n");
		printf("x.exit\n");
		printf("PM>");		
		ch = getc();
		printf("%c\n", ch);
		
		switch(ch){
			case '0':
				stop_mode_test();
				break;
			case '1':
				sleep_mode_test();
				break;
			case '2':
				slow_mode_test();
				break;
			case '3':
				ip_phy_clock_test();
				break;
			case '4':
				test_mode_test();
				break;
			case 'x':
				printf("exit power management test\n");
				return ;
				break;
			default :
				printf("error choose\n");
				break;
		}
	}	
	return ;
}