static int spi_imx_sdma_init(struct device *dev, struct spi_imx_data *spi_imx,
struct spi_master *master,
const struct resource *res)
{
int ret;
/* Prepare for TX DMA: */
master->dma_tx = dma_request_slave_channel(dev, "tx");
if (!master->dma_tx) {
dev_err(dev, "cannot get the TX DMA channel!\n");
ret = -EINVAL;
goto err;
}
spi_imx->tx_config.direction = DMA_MEM_TO_DEV;
spi_imx->tx_config.dst_addr = res->start + MXC_CSPITXDATA;
spi_imx->tx_config.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
spi_imx->tx_config.dst_maxburst = spi_imx_get_fifosize(spi_imx) / 4;
ret = dmaengine_slave_config(master->dma_tx, &spi_imx->tx_config);
if (ret) {
dev_err(dev, "error in TX dma configuration.\n");
goto err;
}
/* Prepare for RX : */
master->dma_rx = dma_request_slave_channel(dev, "rx");
if (!master->dma_rx) {
dev_dbg(dev, "cannot get the DMA channel.\n");
ret = -EINVAL;
goto err;
}
spi_imx->rx_config.direction = DMA_DEV_TO_MEM;
spi_imx->rx_config.src_addr = res->start + MXC_CSPIRXDATA;
spi_imx->rx_config.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
spi_imx->rx_config.src_maxburst = spi_imx_get_fifosize(spi_imx) / 2;
ret = dmaengine_slave_config(master->dma_rx, &spi_imx->rx_config);
if (ret) {
dev_err(dev, "error in RX dma configuration.\n");
goto err;
}
init_completion(&spi_imx->dma_rx_completion);
init_completion(&spi_imx->dma_tx_completion);
master->can_dma = spi_imx_can_dma;
master->max_dma_len = MAX_SDMA_BD_BYTES;
spi_imx->bitbang.master->flags = SPI_MASTER_MUST_RX |
SPI_MASTER_MUST_TX;
spi_imx->rx_wml = spi_imx->rx_config.src_maxburst;
spi_imx->tx_wml = spi_imx->tx_config.dst_maxburst;
spi_imx->dma_is_inited = 1;
return 0;
err:
spi_imx_sdma_exit(spi_imx);
return ret;
}
static bool spi_imx_can_dma(struct spi_master *master, struct spi_device *spi,
struct spi_transfer *transfer)
{
struct spi_imx_data *spi_imx = spi_master_get_devdata(master);
if (transfer && spi_imx->dma_is_inited &&
(transfer->len > spi_imx_get_fifosize(spi_imx)))
return true;
return false;
}
static void spi_imx_push(struct spi_imx_data *spi_imx)
{
while (spi_imx->txfifo < spi_imx_get_fifosize(spi_imx)) {
if (!spi_imx->count)
break;
spi_imx->tx(spi_imx);
spi_imx->txfifo++;
}
spi_imx->devtype_data->trigger(spi_imx);
}
static int spi_imx_sdma_init(struct device *dev, struct spi_imx_data *spi_imx,
struct spi_master *master)
{
int ret;
/* use pio mode for i.mx6dl chip TKT238285 */
if (of_machine_is_compatible("fsl,imx6dl"))
return 0;
spi_imx->wml = spi_imx_get_fifosize(spi_imx) / 2;
/* Prepare for TX DMA: */
master->dma_tx = dma_request_slave_channel_reason(dev, "tx");
if (IS_ERR(master->dma_tx)) {
ret = PTR_ERR(master->dma_tx);
dev_dbg(dev, "can't get the TX DMA channel, error %d!\n", ret);
master->dma_tx = NULL;
goto err;
}
/* Prepare for RX : */
master->dma_rx = dma_request_slave_channel_reason(dev, "rx");
if (IS_ERR(master->dma_rx)) {
ret = PTR_ERR(master->dma_rx);
dev_dbg(dev, "can't get the RX DMA channel, error %d\n", ret);
master->dma_rx = NULL;
goto err;
}
spi_imx_dma_configure(master, 1);
init_completion(&spi_imx->dma_rx_completion);
init_completion(&spi_imx->dma_tx_completion);
master->can_dma = spi_imx_can_dma;
master->max_dma_len = MAX_SDMA_BD_BYTES;
spi_imx->bitbang.master->flags = SPI_MASTER_MUST_RX |
SPI_MASTER_MUST_TX;
return 0;
err:
spi_imx_sdma_exit(spi_imx);
return ret;
}
static int __maybe_unused mx51_ecspi_config(struct spi_imx_data *spi_imx,
struct spi_imx_config *config)
{
u32 ctrl = MX51_ECSPI_CTRL_ENABLE, cfg = 0, dma = 0;
u32 tx_wml_cfg, rx_wml_cfg, rxt_wml_cfg;
u32 clk = config->speed_hz, delay;
/*
* The hardware seems to have a race condition when changing modes. The
* current assumption is that the selection of the channel arrives
* earlier in the hardware than the mode bits when they are written at
* the same time.
* So set master mode for all channels as we do not support slave mode.
*/
ctrl |= MX51_ECSPI_CTRL_MODE_MASK;
/* set clock speed */
ctrl |= mx51_ecspi_clkdiv(spi_imx->spi_clk, config->speed_hz, &clk);
/* set chip select to use */
ctrl |= MX51_ECSPI_CTRL_CS(config->cs);
ctrl |= (config->bpw - 1) << MX51_ECSPI_CTRL_BL_OFFSET;
cfg |= MX51_ECSPI_CONFIG_SBBCTRL(config->cs);
if (config->mode & SPI_CPHA)
cfg |= MX51_ECSPI_CONFIG_SCLKPHA(config->cs);
if (config->mode & SPI_CPOL) {
cfg |= MX51_ECSPI_CONFIG_SCLKPOL(config->cs);
cfg |= MX51_ECSPI_CONFIG_SCLKCTL(config->cs);
}
if (config->mode & SPI_CS_HIGH)
cfg |= MX51_ECSPI_CONFIG_SSBPOL(config->cs);
writel(ctrl, spi_imx->base + MX51_ECSPI_CTRL);
writel(cfg, spi_imx->base + MX51_ECSPI_CONFIG);
/*
* Wait until the changes in the configuration register CONFIGREG
* propagate into the hardware. It takes exactly one tick of the
* SCLK clock, but we will wait two SCLK clock just to be sure. The
* effect of the delay it takes for the hardware to apply changes
* is noticable if the SCLK clock run very slow. In such a case, if
* the polarity of SCLK should be inverted, the GPIO ChipSelect might
* be asserted before the SCLK polarity changes, which would disrupt
* the SPI communication as the device on the other end would consider
* the change of SCLK polarity as a clock tick already.
*/
delay = (2 * 1000000) / clk;
if (likely(delay < 10)) /* SCLK is faster than 100 kHz */
udelay(delay);
else /* SCLK is _very_ slow */
usleep_range(delay, delay + 10);
/*
* Configure the DMA register: setup the watermark
* and enable DMA request.
*/
if (spi_imx->dma_is_inited) {
dma = readl(spi_imx->base + MX51_ECSPI_DMA);
spi_imx->rxt_wml = spi_imx_get_fifosize(spi_imx) / 2;
rx_wml_cfg = spi_imx->rx_wml << MX51_ECSPI_DMA_RX_WML_OFFSET;
tx_wml_cfg = spi_imx->tx_wml << MX51_ECSPI_DMA_TX_WML_OFFSET;
rxt_wml_cfg = spi_imx->rxt_wml << MX51_ECSPI_DMA_RXT_WML_OFFSET;
dma = (dma & ~MX51_ECSPI_DMA_TX_WML_MASK
& ~MX51_ECSPI_DMA_RX_WML_MASK
& ~MX51_ECSPI_DMA_RXT_WML_MASK)
| rx_wml_cfg | tx_wml_cfg | rxt_wml_cfg
|(1 << MX51_ECSPI_DMA_TEDEN_OFFSET)
|(1 << MX51_ECSPI_DMA_RXDEN_OFFSET)
|(1 << MX51_ECSPI_DMA_RXTDEN_OFFSET);
writel(dma, spi_imx->base + MX51_ECSPI_DMA);
}
return 0;
}
