static unsigned long clk_get_rate_mclk(struct clk *clk)
{
u16 val;
val = syscon_clk_get_rate();
switch (val) {
case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER:
return 13000000;
case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW:
case U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE:
case U300_SYSCON_CCR_CLKING_PERFORMANCE_HIGH:
case U300_SYSCON_CCR_CLKING_PERFORMANCE_BEST:
{
u16 val = readw(U300_SYSCON_VBASE + U300_SYSCON_MMF0R) &
U300_SYSCON_MMF0R_MASK;
switch (val) {
case 0x0054:
return 18900000;
case 0x0044:
return 20800000;
case 0x0043:
return 23100000;
case 0x0033:
return 26000000;
case 0x0032:
return 29700000;
case 0x0022:
return 34700000;
case 0x0021:
return 41600000;
case 0x0011:
return 52000000;
case 0x0000:
return 104000000;
default:
break;
}
}
default:
break;
}
return clk->rate;
}
static unsigned long clk_get_rate_i2s_i2c_spi(struct clk *clk)
{
u16 val;
val = syscon_clk_get_rate();
switch (val) {
case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER:
case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW:
return 13000000;
case U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE:
case U300_SYSCON_CCR_CLKING_PERFORMANCE_HIGH:
case U300_SYSCON_CCR_CLKING_PERFORMANCE_BEST:
return 26000000;
default:
break;
}
return clk->rate;
}
static unsigned long clk_get_rate_mclk(struct clk *clk)
{
u16 val;
val = syscon_clk_get_rate();
switch (val) {
case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER:
/*
* Here, the 208 MHz PLL gets shut down and the always
* on 13 MHz PLL used for RTC etc kicks into use
* instead.
*/
return 13000000;
case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW:
case U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE:
case U300_SYSCON_CCR_CLKING_PERFORMANCE_HIGH:
case U300_SYSCON_CCR_CLKING_PERFORMANCE_BEST:
{
/*
* This clock is under program control. The register is
* divided in two nybbles, bit 7-4 gives cycles-1 to count
* high, bit 3-0 gives cycles-1 to count low. Distribute
* these with no more than 1 cycle difference between
* low and high and add low and high to get the actual
* divisor. The base PLL is 208 MHz. Writing 0x00 will
* divide by 1 and 1 so the highest frequency possible
* is 104 MHz.
*
* e.g. 0x54 =>
* f = 208 / ((5+1) + (4+1)) = 208 / 11 = 18.9 MHz
*/
u16 val = readw(U300_SYSCON_VBASE + U300_SYSCON_MMF0R) &
U300_SYSCON_MMF0R_MASK;
switch (val) {
case 0x0054:
return 18900000;
case 0x0044:
return 20800000;
case 0x0043:
return 23100000;
case 0x0033:
return 26000000;
case 0x0032:
return 29700000;
case 0x0022:
return 34700000;
case 0x0021:
return 41600000;
case 0x0011:
return 52000000;
case 0x0000:
return 104000000;
default:
break;
}
}
default:
break;
}
return clk->rate;
}
