int main(void)
{
//! [init]
system_clock_config(CLOCK_RESOURCE_XO_26_MHZ, CLOCK_FREQ_26_MHZ);
configure_i2c_slave();
//! [packet]
struct i2c_slave_packet packet = {
.data_length = DATA_LENGTH,
.data = write_buffer,
};
//! [packet]
//! [init]
//! [while]
while (true) {
packet.data = read_buffer;
i2c_slave_read_packet_wait(&i2c_slave_instance, &packet);
packet.data = write_buffer;
i2c_slave_write_packet_wait(&i2c_slave_instance, &packet);
}
//! [while]
}
int main(void)
{
system_clock_config(CLOCK_RESOURCE_XO_26_MHZ, CLOCK_FREQ_26_MHZ);
//! [setup_init]
configure_adc();
//! [setup_init]
//! [main]
//! [get_res]
uint16_t result;
do {
/* Wait for conversion to be done and read out result */
} while (adc_read(CONF_ADC_INPUT_CH, &result) == STATUS_BUSY);
//! [get_res]
//! [inf_loop]
while (1) {
/* Infinite loop */
}
//! [inf_loop]
//! [main]
}
int main(void)
{
//! [main_start]
uint8_t result = 0;
uint16_t i;
uint32_t delay;
/* Initialize system */
//! [system_init]
system_clock_config(CLOCK_RESOURCE_XO_26_MHZ, CLOCK_FREQ_26_MHZ);
for (i = 0; i < BUF_LENGTH; i++) {
buffer_expect[i] = i;
buffer_rx[i] = 0;
}
//! [system_init]
//! [run_config_gpio]
configure_gpio();
//! [run_config_gpio]
//! [run_config_spi]
configure_spi_slave();
//! [run_config_spi]
//! [main_start]
//! [main_use_case]
//! [read]
memset(buffer_rx, 0x0, BUF_LENGTH);
while(spi_read_buffer_wait(&spi_slave_instance, buffer_rx, BUF_LENGTH,
0x00) != STATUS_OK) {
/* Wait for transfer from the master */
}
//! [read]
//! [compare]
for (i = 0; i < BUF_LENGTH; i++) {
if(buffer_rx[i] != buffer_expect[i]) {
result++;
}
}
//! [compare]
//! [inf_loop]
while (true) {
/* Infinite loop */
if (result) {
gpio_pin_toggle_output_level(LED_0_PIN);
/* Add a short delay to see LED toggle */
delay = 300000;
while(delay--) {
}
} else {
gpio_pin_toggle_output_level(LED_0_PIN);
/* Add a short delay to see LED toggle */
delay = 3000000;
while(delay--) {
}
}
}
//! [inf_loop]
//! [main_use_case]
}
int main(void)
{
system_clock_config(CLOCK_RESOURCE_XO_26_MHZ, CLOCK_FREQ_26_MHZ);
//! [setup_init]
configure_pwm();
//! [setup_init]
//! [main]
while (true) {
/* Infinite loop */
}
//! [main]
}
int main(void)
{
volatile double temper_value;
volatile bool data_check_status1 = true,
data_check_status2 = true;
uint32_t i;
system_clock_config(CLOCK_RESOURCE_XO_26_MHZ, CLOCK_FREQ_26_MHZ);
/* Initialize AT30TS(E)75x */
at30tse_init();
/* First round data check */
for (i = 0; i < NB_BYTE; i++) {
tx_buffer[i] = i;
}
/* Write pages in EEPROM */
for (i = 0; i < NB_PAGE; i++) {
at30tse_eeprom_write(tx_buffer, NB_BYTE, 0, i);
delay(200);
}
/* Read each page in EEPROM and compare them */
for (i = 0; i < NB_PAGE; i++) {
memset(rx_buffer, 0, NB_BYTE);
at30tse_eeprom_read(rx_buffer, NB_BYTE, 0, i);
if (memcmp(tx_buffer, rx_buffer, NB_BYTE)) {
data_check_status1 = false;
break;
}
}
/* Second round data check */
for (i = 0; i < NB_BYTE; i++) {
tx_buffer[i] = NB_BYTE - i;
}
/* Write pages in EEPROM */
for (i = 0; i < NB_PAGE; i++) {
at30tse_eeprom_write(tx_buffer, NB_BYTE, 0, i);
delay(200);
}
/* Read each page in EEPROM and compare them */
for (i = 0; i < NB_PAGE; i++) {
memset(rx_buffer, 0, NB_BYTE);
at30tse_eeprom_read(rx_buffer, NB_BYTE, 0, i);
if (memcmp(tx_buffer, rx_buffer, NB_BYTE)) {
data_check_status2 = false;
break;
}
}
/* Read thigh and tlow */
volatile uint16_t thigh = 0;
thigh = at30tse_read_register(AT30TSE_THIGH_REG,
AT30TSE_NON_VOLATILE_REG, AT30TSE_THIGH_REG_SIZE);
volatile uint16_t tlow = 0;
tlow = at30tse_read_register(AT30TSE_TLOW_REG,
AT30TSE_NON_VOLATILE_REG, AT30TSE_TLOW_REG_SIZE);
/* Set 12-bit resolution mode. */
at30tse_write_config_register(
AT30TSE_CONFIG_RES(AT30TSE_CONFIG_RES_12_bit));
while (1) {
/* Read current temperature. */
temper_value = at30tse_read_temperature();
}
UNUSED(data_check_status1);
UNUSED(data_check_status2);
UNUSED(temper_value);
UNUSED(tlow);
UNUSED(thigh);
}
