C++ (Cpp) upmu_set_rg_vgp2_vosel Examples

Example #1

0

Show file

File: LP079X01.c Project: CryToCry96/MT6582_kernel_source

static void lcd_power_en(unsigned char enabled)
{
    if (enabled)
    {      
#ifdef BUILD_LK
        /* VGP2_PMU 3V */
        pmic_config_interface(DIGLDO_CON29, 0x6, PMIC_RG_VGP2_VOSEL_MASK, PMIC_RG_VGP2_VOSEL_SHIFT);
        pmic_config_interface(DIGLDO_CON8, 0x1, PMIC_RG_VGP2_EN_MASK, PMIC_RG_VGP2_EN_SHIFT);
#else
        //hwPowerOn(MT65XX_POWER_LDO_VGP2, VOL_3000, "LCM");
        //hwPowerOn(MT6323_POWER_LDO_VGP2, VOL_3000, "LCM");
        upmu_set_rg_vgp2_vosel(0x6);
        upmu_set_rg_vgp2_en(0x1);
#endif
        mt_set_gpio_mode(GPIO_VLCD_VCC_EN, GPIO_MODE_00);
        mt_set_gpio_dir(GPIO_VLCD_VCC_EN, GPIO_DIR_OUT);
        mt_set_gpio_out(GPIO_VLCD_VCC_EN, GPIO_OUT_ONE);
    }
    else
    {      
#ifdef BUILD_LK
        /* VGP2_PMU 3V */
        pmic_config_interface(DIGLDO_CON8, 0x0, PMIC_RG_VGP2_EN_MASK, PMIC_RG_VGP2_EN_SHIFT);
        pmic_config_interface(DIGLDO_CON29, 0x0, PMIC_RG_VGP2_VOSEL_MASK, PMIC_RG_VGP2_VOSEL_SHIFT); 
#else
        //hwPowerDown(MT65XX_POWER_LDO_VGP2, "LCM");
        //hwPowerDown(MT6323_POWER_LDO_VGP2, "LCM");
        upmu_set_rg_vgp2_en(0x0);        
        upmu_set_rg_vgp2_vosel(0x0);
#endif
        mt_set_gpio_mode(GPIO_VLCD_VCC_EN, GPIO_MODE_00);
        mt_set_gpio_dir(GPIO_VLCD_VCC_EN, GPIO_DIR_OUT);
        mt_set_gpio_out(GPIO_VLCD_VCC_EN, GPIO_OUT_ZERO);
    }
}

Example #2

0

Show file

File: r69338_hd720_dsi_vdo_jdi.c Project: Elnter/j608_kernel

/* VGP2 3.0v LDO enable */
static void ldo_3v0_on(void)
{

#ifdef BUILD_UBOOT 
	#error "not implemeted"
#elif defined(BUILD_LK)
    #if defined(_Y70_Rev_A_)    // Y70 Rev.A board
	upmu_set_rg_vgp1_vosel(6);  // VGP2_SEL= 101 : 2.8V , 110 : 3.0V
	upmu_set_rg_vgp1_en(1);    
    #elif defined(_Y70_Rev_B_)  // Y70 Rev.B board    
	upmu_set_rg_vgp2_vosel(6);  // VGP2_SEL= 101 : 2.8V , 110 : 3.0V
	upmu_set_rg_vgp2_en(1);
    #else               // Y70 Rev.A-2 board
	upmu_set_rg_vgp2_vosel(6);  // VGP2_SEL= 101 : 2.8V , 110 : 3.0V
	upmu_set_rg_vgp2_en(1);	
    #endif /* _Y70_Rev_A_ */
#else
    #if defined(_Y70_Rev_A_)    // Y70 Rev.A board
	hwPowerOn(MT6323_POWER_LDO_VGP1, VOL_3000, "3V0_TOUCH_VDD");	    
    #elif defined(_Y70_Rev_B_)  // Y70 Rev.B board        
	hwPowerOn(MT6323_POWER_LDO_VGP2, VOL_3000, "3V0_MTK_LCD_VCC");	
    #else               // Y70 Rev.A-2 board
	hwPowerOn(MT6323_POWER_LDO_VGP2, VOL_3000, "3V0_LCD_VCC_MTK_S");	
    #endif /* _Y70_Rev_A_ */
#endif

}

Example #3

0

Show file

File: nt35517_qhd_dsi_video.c Project: luckasfb/a3-ll

static void lcd_power_en(unsigned char enabled)
{
    #ifdef BUILD_LK
		printf("%s,  %d LK \n", __func__, enabled);
	#else
		printk("%s, %d kernel", __func__, enabled);
	#endif
    if (enabled)
    {      
#ifdef BUILD_LK
#if 0
    #ifdef MTK_PMIC_MT6397
    #else
        /* VGP2_PMU 3V */
        pmic_config_interface(DIGLDO_CON29, 0x6, PMIC_RG_VGP2_VOSEL_MASK, PMIC_RG_VGP2_VOSEL_SHIFT);
        pmic_config_interface(DIGLDO_CON8, 0x1, PMIC_RG_VGP2_EN_MASK, PMIC_RG_VGP2_EN_SHIFT);
    #endif
#endif
    upmu_set_rg_vgp6_vosel(0x05);
    upmu_set_rg_vgp6_sw_en(0x01);
#else
#if 0
    #ifdef MTK_PMIC_MT6397
    #else
        upmu_set_rg_vgp2_vosel(0x6);
        upmu_set_rg_vgp2_en(0x1);
    #endif
#endif
    upmu_set_rg_vgp6_vosel(0x05);
    upmu_set_rg_vgp6_sw_en(0x01);
#endif
        //mt_set_gpio_out(GPIO_LCM_PWR, GPIO_OUT_ONE);
    }
    else
    {      
#ifdef BUILD_LK
#if 0
    #ifdef MTK_PMIC_MT6397
    #else
        /* VGP2_PMU 3V */
        pmic_config_interface(DIGLDO_CON8, 0x0, PMIC_RG_VGP2_EN_MASK, PMIC_RG_VGP2_EN_SHIFT);
        pmic_config_interface(DIGLDO_CON29, 0x0, PMIC_RG_VGP2_VOSEL_MASK, PMIC_RG_VGP2_VOSEL_SHIFT); 
    #endif
#endif
    upmu_set_rg_vgp6_vosel(0x0);
    upmu_set_rg_vgp6_sw_en(0x0);
#else
#if 0
    #ifdef MTK_PMIC_MT6397
    #else
        upmu_set_rg_vgp2_en(0x0);        
        upmu_set_rg_vgp2_vosel(0x0);
    #endif
#endif
    upmu_set_rg_vgp6_vosel(0x0);
    upmu_set_rg_vgp6_sw_en(0x0);
#endif
        //mt_set_gpio_out(GPIO_LCM_PWR, GPIO_OUT_ZERO);
    }
}

Example #4

0

Show file

File: r63302_sharp_LS035Y8DX02A_rgb_wvga.c Project: SeriniTY320/mediatek

static void lcm_init(void)
{
#ifdef BUILD_LK
    upmu_set_rg_vgp2_vosel(5);
    upmu_set_rg_vgp2_en(1);
    MDELAY(50);
		
    upmu_set_rg_vgp3_vosel(3);
    upmu_set_rg_vgp3_en(1); 
#else
    hwPowerOn(MT6323_POWER_LDO_VGP2,VOL_2800,"LCM28");
    hwPowerOn(MT6323_POWER_LDO_VGP3,VOL_1800,"LCM18");
#endif
    MDELAY(100);

    config_gpio();
    SET_RESET_PIN(1);
    MDELAY(10);
    SET_RESET_PIN(0);
    MDELAY(20);
    SET_RESET_PIN(1);
    MDELAY(50);

    init_lcm_registers();
}

Example #5

0

Show file

File: otm9605a_ykl_LP047APTP018A_V01_AUO_dsi_2_vdo_qhd.c Project: SeriniTY320/mediatek

static unsigned int lcm_compare_id(void)
{
	int   array[4];
		char  buffer[5];
		unsigned int id=0;
	#if defined(BUILD_LK)
	upmu_set_rg_vgp2_vosel(5);
	upmu_set_rg_vgp2_en(1);

	upmu_set_rg_vgp3_vosel(3);
	upmu_set_rg_vgp3_en(1);	
#else
	hwPowerOn(MT6323_POWER_LDO_VGP2, VOL_2800, "Lance_LCM");
  hwPowerOn(MT6323_POWER_LDO_VGP3, VOL_1800, "Lance_LCM");
#endif
    MDELAY(100);	
		SET_RESET_PIN(0);
		MDELAY(200);
		SET_RESET_PIN(1);
		MDELAY(200);
		
	array[0] = 0x00083700;// read id return two byte,version and id
	dsi_set_cmdq(array, 1, 1);

	read_reg_v2(0xA1,buffer,4);
	
	id=(buffer[2]<<8)+buffer[3];

	return (LCM_ID == id)?1:0;
}

Example #6

0

Show file

File: hx8357d_apex_A35406N00QH_A_CMI_dsi_cmd_hvga.c Project: SeriniTY320/mediatek

static unsigned int lcm_compare_id(void)
{
	unsigned int id = 0;
	unsigned char buffer[2];
	unsigned int array[16];
		
#ifdef BUILD_LK
	upmu_set_rg_vgp2_vosel(5);
	upmu_set_rg_vgp2_en(1);

	upmu_set_rg_vgp3_vosel(3);
	upmu_set_rg_vgp3_en(1);	
#else
  hwPowerOn(MT6323_POWER_LDO_VGP2,VOL_2800,"LCM");
	hwPowerOn(MT6323_POWER_LDO_VGP3,VOL_1800,"LCM");
#endif
  MDELAY(100);

  SET_RESET_PIN(1);
  MDELAY(10);
  SET_RESET_PIN(0);
  MDELAY(50);
  SET_RESET_PIN(1);
  MDELAY(100);
  
	array[0] = 0x00043700;// read id return two byte,version and id
	dsi_set_cmdq(array, 1, 1);
	
	read_reg_v2(0x04, buffer, 4);
	id = buffer[1]; //we only need ID

	Lcd_Log("wqcat read HX8369A id=%x,%x\n", buffer[0],buffer[1]);
	return ((LCM_ID == id)&&(get_lcd_id()==1))?1:0;
}

Example #7

0

Show file

File: otm8019a_zhuoershi_MS_Z50439N00B3O_BOE_dsi_vdo_2_fwvga.c Project: SeriniTY320/mediatek

static void lcm_init(void)
{
	  int flag=0;
	  
	#if defined(BUILD_LK)
	upmu_set_rg_vgp2_vosel(5);
	upmu_set_rg_vgp2_en(1);

	upmu_set_rg_vgp3_vosel(3);
	upmu_set_rg_vgp3_en(1);	
#else
	hwPowerOn(MT6323_POWER_LDO_VGP2, VOL_2800, "Lance_LCM");
  hwPowerOn(MT6323_POWER_LDO_VGP3, VOL_1800, "Lance_LCM");
#endif
		  //MDELAY(100);

    

    SET_RESET_PIN(1);
    SET_RESET_PIN(0);
    MDELAY(1);
    SET_RESET_PIN(1);
    MDELAY(10);
  
    Lcd_Log("mycat otm8018b flag=%d  \n",flag);
    
	  push_table(lcm_initialization_setting, sizeof(lcm_initialization_setting) / sizeof(struct LCM_setting_table), 1);
}

Example #8

0

Show file

File: otm9605a_aizuoertai_A50100N51HD_dsi_qhd.c Project: SeriniTY320/mediatek

static void lcm_init(void)
{
int kk =0;
	#if defined(BUILD_LK)
	upmu_set_rg_vgp2_vosel(5);
	upmu_set_rg_vgp2_en(1);

	upmu_set_rg_vgp3_vosel(3);
	upmu_set_rg_vgp3_en(1);	
#else
	hwPowerOn(MT6323_POWER_LDO_VGP2, VOL_2800, "Lance_LCM");
  hwPowerOn(MT6323_POWER_LDO_VGP3, VOL_1800, "Lance_LCM");
#endif
    MDELAY(100);


    SET_RESET_PIN(1);
    SET_RESET_PIN(0);
    MDELAY(10);//10
    SET_RESET_PIN(1);
    MDELAY(50);//50
     kk = lcm_check_id();
	if(kk == 1)
	{
            push_table(lcm_initialization_setting_ykl, sizeof(lcm_initialization_setting_ykl) / sizeof(struct LCM_setting_table), 1);
	}
	else
	{
           push_table(lcm_initialization_setting, sizeof(lcm_initialization_setting) / sizeof(struct LCM_setting_table), 1);
	}
}

Example #9

0

Show file

File: r69338_hd720_dsi_vdo_jdi.c Project: Elnter/j608_kernel

/* VCAMD 1.8v LDO enable */
static void ldo_1v8io_on(void)
{
#ifdef BUILD_UBOOT 
	#error "not implemeted"
#elif defined(BUILD_LK) 	
    if ( g_PCBver==HW_REV_B )
    {
    	upmu_set_rg_vgp1_vosel(3);  // VGP2_SEL= 101 : 2.8V , 110 : 3.0V
    	upmu_set_rg_vgp1_en(1);        
    }
    else if ( g_PCBver==HW_REV_A_2 )
    {
    	upmu_set_rg_vcamd_vosel(3);  // VGP2_SEL= 101 : 2.8V , 110 : 3.0V
    	upmu_set_rg_vcamd_en(1);        
    }
    else    //( g_PCBver==HW_REV_A )
    {
    	upmu_set_rg_vgp2_vosel(3);  // VGP2_SEL= 101 : 2.8V , 110 : 3.0V
    	upmu_set_rg_vgp2_en(1);
    }
#else
    if ( g_PCBver==HW_REV_B )
    {
    	hwPowerOn(MT6323_POWER_LDO_VGP1, VOL_1800, "1V8_MTK_LCD_IO");	        
    }
    else if ( g_PCBver==HW_REV_A_2 )
    {
    	hwPowerOn(MT6323_POWER_LDO_VCAMD, VOL_1800, "1V8_LCD_VIO_MTK_S");	        
    }
    else    //( g_PCBver==HW_REV_A )
    {
    	hwPowerOn(MT6323_POWER_LDO_VGP2, VOL_1800, "1V8_LCD_VIO_MTK_S");	        
    }    
#endif 
}

Example #10

0

Show file

File: r69338_hd720_dsi_vdo_jdi.c Project: Elnter/j608_kernel

/* VCAMD 1.8v LDO enable */
static void ldo_1v8io_on(void)
{
#ifdef BUILD_UBOOT 
	#error "not implemeted"
#elif defined(BUILD_LK) 	
    #if defined(_Y70_Rev_A_)    // Y70 Rev.A board
	upmu_set_rg_vgp2_vosel(3);  // VGP2_SEL= 101 : 2.8V , 110 : 3.0V
	upmu_set_rg_vgp2_en(1);
    #elif defined(_Y70_Rev_B_)  // Y70 Rev.B board
	upmu_set_rg_vgp1_vosel(3);  // VGP2_SEL= 101 : 2.8V , 110 : 3.0V
	upmu_set_rg_vgp1_en(1);
    #else               // Y70 Rev.A-2 board
	upmu_set_rg_vcamd_vosel(3);  // VGP2_SEL= 101 : 2.8V , 110 : 3.0V
	upmu_set_rg_vcamd_en(1);
    #endif /* _Y70_Rev_A_ */
#else
    #if defined(_Y70_Rev_A_)    // Y70 Rev.A board
	hwPowerOn(MT6323_POWER_LDO_VGP2, VOL_1800, "1V8_LCD_VIO_MTK_S");	    
    #elif defined(_Y70_Rev_B_)  // Y70 Rev.B board
	hwPowerOn(MT6323_POWER_LDO_VGP1, VOL_1800, "1V8_MTK_LCD_IO");	
    #else               // Y70 Rev.A-2 board
	hwPowerOn(MT6323_POWER_LDO_VCAMD, VOL_1800, "1V8_LCD_VIO_MTK_S");	
    #endif /* _Y70_Rev_A_ */
#endif 
}

Example #11

0

Show file

File: nt35510_aizhuoertai_A40249N50XN_A_Hyundai_dsi_wvga.c Project: SeriniTY320/mediatek

static unsigned int lcm_compare_id(void)
{
	int i;
#if defined(BUILD_LK)
	upmu_set_rg_vgp2_vosel(5);
	upmu_set_rg_vgp2_en(1);

	upmu_set_rg_vgp3_vosel(3);
	upmu_set_rg_vgp3_en(1);	
#else
	hwPowerOn(MT6323_POWER_LDO_VGP2, VOL_2800, "Lance_LCM");
       hwPowerOn(MT6323_POWER_LDO_VGP3, VOL_1800, "Lance_LCM");
#endif
  MDELAY(100);
  	mt_set_gpio_mode(GPIO_LCD_PIN_ID, GPIO_MODE_00);
	 mt_set_gpio_dir(GPIO_LCD_PIN_ID, GPIO_DIR_IN);
	//mt_set_gpio_pull_enable(GPIO_LCD_PIN_ID, 1);
	//mt_set_gpio_pull_select(GPIO_LCD_PIN_ID, GPIO_PULL_UP);	
  	
 	i=mt_get_gpio_in(GPIO_LCD_PIN_ID);  
#ifdef BUILD_LK
	printf("MYCAT NT35512 lk  lcm_compare_id=%d\n",i);
#else
     printk("MYCAT NT35512 kernel  lcm_compare_id=%d\n",i);
#endif
	if(i == 1)
		return 1;
	else
    		return 1;
}

Example #12

0

Show file

File: otm8018b_PUNAI_PT040WVH010A_HSD_dsi_2_wvga.c Project: SeriniTY320/mediatek

static void lcm_init(void)
{


#ifdef BUILD_LK
    upmu_set_rg_vgp2_vosel(5);
    upmu_set_rg_vgp2_en(1);
    MDELAY(50);
    
    upmu_set_rg_vgp3_vosel(3);
    upmu_set_rg_vgp3_en(1); 
     
#else
    hwPowerOn(MT6323_POWER_LDO_VGP2,VOL_2800,"LCM28");
    hwPowerOn(MT6323_POWER_LDO_VGP3,VOL_1800,"LCM18");
#endif
		  MDELAY(50);

    SET_RESET_PIN(1);
    SET_RESET_PIN(0);
    MDELAY(1);
    SET_RESET_PIN(1);
    MDELAY(10);
  

	 push_table(lcm_initialization_setting1, sizeof(lcm_initialization_setting1) / sizeof(struct LCM_setting_table), 1);
}

Example #13

0

Show file

File: ILI9488_QIJIA_FX350001S0_HSD_DSI_CMD_HVGA.c Project: SeriniTY320/mediatek

static void lcm_init(void)
{
#if defined(BUILD_LK)
	upmu_set_rg_vgp2_vosel(5);
	upmu_set_rg_vgp2_en(1);

	upmu_set_rg_vgp3_vosel(3);
	upmu_set_rg_vgp3_en(1);	
#else
	hwPowerOn(MT6323_POWER_LDO_VGP2, VOL_2800, "Lance_LCM");
 	hwPowerOn(MT6323_POWER_LDO_VGP3, VOL_1800, "Lance_LCM");
#endif

#ifdef BUILD_LK
	printf("MYCAT ILI9608 lk lcm_init\n");
#else
      printk("MYCAT ILI9608  kernel lcm_init\n");
#endif
    SET_RESET_PIN(1);
    MDELAY(10);
    SET_RESET_PIN(0);
    MDELAY(50);
    SET_RESET_PIN(1);
    MDELAY(180);
		push_table(lcm_initialization_setting, sizeof(lcm_initialization_setting) / sizeof(struct LCM_setting_table), 1);
    //init_lcm_registers();
}

Example #14

0

Show file

File: otm9605_hengsheng_HS050PQ_76H_CPT_dsi_vdo_qhd.c Project: SeriniTY320/mediatek

static void lcm_init(void)
{
	unsigned int data_array[64];
	
	#if defined(BUILD_LK)
	upmu_set_rg_vgp2_vosel(5);
	upmu_set_rg_vgp2_en(1);

	upmu_set_rg_vgp3_vosel(3);
	upmu_set_rg_vgp3_en(1);	
#else
	hwPowerOn(MT6323_POWER_LDO_VGP2, VOL_2800, "Lance_LCM");
       hwPowerOn(MT6323_POWER_LDO_VGP3, VOL_1800, "Lance_LCM");
#endif

    mt_set_gpio_mode(59,GPIO_MODE_00);
    mt_set_gpio_dir(59,GPIO_DIR_OUT);
    mt_set_gpio_out(59,GPIO_OUT_ONE);
 MDELAY(10);//Must > 10ms
	 mt_set_gpio_out(59,GPIO_OUT_ZERO);
 MDELAY(10);//Must > 10ms
	  mt_set_gpio_out(59,GPIO_OUT_ONE);
   MDELAY(120);//Must > 120m

    push_table(lcm_initialization_setting, sizeof(lcm_initialization_setting) / sizeof(struct LCM_setting_table), 1);
}

Example #15

0

Show file

File: RM68171_QICAI_K40BM231423A1N_BOE_DSI_2_WVGA_VDO.c Project: SeriniTY320/mediatek

static unsigned int lcm_compare_id(void)
{
	#if defined(BUILD_LK)
		upmu_set_rg_vgp2_vosel(5);
		upmu_set_rg_vgp2_en(1);
		
		upmu_set_rg_vgp3_vosel(3);
		upmu_set_rg_vgp3_en(1);	
#else
		hwPowerOn(MT6323_POWER_LDO_VGP2, VOL_2800, "Lance_LCM");
		hwPowerOn(MT6323_POWER_LDO_VGP3, VOL_1800, "Lance_LCM");
#endif
 	unsigned int id = 0;
	unsigned char buffer[3];
	unsigned int array[16];
	
	SET_RESET_PIN(1);  //NOTE:should reset LCM firstly
	SET_RESET_PIN(0);
	MDELAY(6);
	SET_RESET_PIN(1);
	MDELAY(50);

	array[0] = 0x00033700;// read id return two byte,version and id
	dsi_set_cmdq(array, 1, 1);
	read_reg_v2(0x04, buffer, 3);
	id = ((buffer[1]<<8)&0xFF00)|(buffer[0]&0x00FF); //we only need ID

	Lcd_Log("wqcat %s, id1 = 0x%08x, id2 = 0x%08x\n", __func__, buffer[0], buffer[1]);

  return (id==LCM_ID&&get_lcd_id()==0)?1:0;
}

Example #16

0

Show file

File: ili9806E_jingtai_JTD050121S0_HSD_dsi_2_vdo_fwvga.c Project: SeriniTY320/mediatek

static unsigned int lcm_compare_id(void)
{
        unsigned int array[4];
        unsigned char buffer[1];
        unsigned char id_high=0;
        unsigned char id_midd=0;
        unsigned char id_low=0;
        unsigned int id=0;
	Lcd_Log("lcm_compare_id\n");
#if defined(BUILD_LK)
	upmu_set_rg_vgp2_vosel(5);
	upmu_set_rg_vgp2_en(1);
	upmu_set_rg_vgp3_vosel(3);
	upmu_set_rg_vgp3_en(1);
	
#else
	hwPowerOn(MT6323_POWER_LDO_VGP2, VOL_2800, "Lance_LCM");
	hwPowerOn(MT6323_POWER_LDO_VGP3, VOL_1800, "Lance_LCM");
#endif
	MDELAY(50);

#ifdef BUILD_LK
	printf("MYCAT ILI9608 lk lcm_init\n");
#else
      printk("MYCAT ILI9608  kernel lcm_init\n");
#endif
    SET_RESET_PIN(1);
    MDELAY(30);
    SET_RESET_PIN(0);
    MDELAY(50);
    SET_RESET_PIN(1);
    MDELAY(120);

        array[0]=0x00063902;
        array[1]=0x0698ffff;
        array[2]=0x00000104;
        dsi_set_cmdq(array, 3, 1);
        MDELAY(10);

        array[0]=0x00023700;
        dsi_set_cmdq(array, 1, 1);
        //read_reg_v2(0x04, buffer, 3);//if read 0x04,should get 0x008000,that is both OK.
    
        read_reg_v2(0x00, buffer,1);
        id_high = buffer[0]; ///////////////////////0x98

        read_reg_v2(0x01, buffer,1);
        id_midd = buffer[0]; ///////////////////////0x06

        read_reg_v2(0x02, buffer,1);
        id_low = buffer[0]; ////////////////////////0x04

        id = (id_high << 16) | (id_midd << 8) | id_low;
        
        Lcd_Log("id=0x%x,get_lcd_id=%d \n",id,get_lcd_id());
//        return (LCM_ID == id)?1:0;
        //return (get_lcd_id()==1)?1:0;
	return (LCM_ID == id&&get_lcd_id()==0)?1:0;
        }

Example #17

0

Show file

File: ili9806e_jingtai_JTD040379B0_BOE_dsi_2_vdo_wvga.c Project: SeriniTY320/mediatek

static unsigned int lcm_compare_id(void)
{
#if defined(BUILD_LK)
		upmu_set_rg_vgp2_vosel(5);
		upmu_set_rg_vgp2_en(1);
		
		upmu_set_rg_vgp3_vosel(3);
		upmu_set_rg_vgp3_en(1);	
#else
		hwPowerOn(MT6323_POWER_LDO_VGP2, VOL_2800, "Lance_LCM");
		hwPowerOn(MT6323_POWER_LDO_VGP3, VOL_1800, "Lance_LCM");
#endif
    int array[4];
    char buffer[1];
    char id_high=0;
    char id_midd=0;
    char id_low=0;
    int id=0;

    //Do reset here
    SET_RESET_PIN(1);
    SET_RESET_PIN(0);
    MDELAY(25);       
    SET_RESET_PIN(1);
    MDELAY(50);      
   
    array[0]=0x00063902;
    array[1]=0x0698ffff;
    array[2]=0x00000104;
    dsi_set_cmdq(array, 3, 1);
    MDELAY(10);

    array[0]=0x00023700;
    dsi_set_cmdq(array, 1, 1);
    //read_reg_v2(0x04, buffer, 3);//if read 0x04,should get 0x008000,that is both OK.

    read_reg_v2(0x00, buffer,1);
    id_high = buffer[0]; ///////////////////////0x98

    read_reg_v2(0x01, buffer,1);
    id_midd = buffer[0]; ///////////////////////0x06

    read_reg_v2(0x02, buffer,1);
    id_low = buffer[0]; ////////////////////////0x04

    id = (id_high << 16) | (id_midd << 8) | id_low;
    
    Lcd_Log("wqcat %s, 0x00=0x%x,0x01=0x%x,0x02=0x%x,id=0x%x\n", __func__, id_high,id_midd,id_low,id);
    return (LCM_ID == id&&get_lcd_id()==1)?1:0;
    //return (get_lcd_id()==1)?1:0;

}

Example #18

0

Show file

File: hx8369b_liangjingjing_LT43062EHT01_72M_BOE_dsi_wvga.c Project: SeriniTY320/mediatek

static unsigned int lcm_compare_id()
{
//	return 1;
#if 0	
    unsigned int id = 0, id2 = 0;
    unsigned char buffer[2];
    unsigned int data_array[16];

#if defined(BUILD_LK)
	upmu_set_rg_vgp2_vosel(5);
	upmu_set_rg_vgp2_en(1);

	upmu_set_rg_vgp3_vosel(3);
	upmu_set_rg_vgp3_en(1);	
#else
	hwPowerOn(MT6323_POWER_LDO_VGP2, VOL_2800, "Lance_LCM");
       hwPowerOn(MT6323_POWER_LDO_VGP3, VOL_1800, "Lance_LCM");
#endif
    MDELAY(100);


    SET_RESET_PIN(1);
    MDELAY(20);
    SET_RESET_PIN(0);
    MDELAY(50);
    SET_RESET_PIN(1);
    MDELAY(100);

    //*************Enable CMD2 Page1  *******************//
    data_array[0]=0x00043902;
    data_array[1]=0x6983ffb9;//52AA55F0;
    //data_array[2]=0x00000108;
    dsi_set_cmdq(data_array, 3, 1);
    MDELAY(10);

    data_array[0] = 0x00023700;// read id return two byte,version and id
    dsi_set_cmdq(data_array, 1, 1);
    MDELAY(10);

    read_reg_v2(0xF4, buffer, 2);
    id = buffer[0]; //we only need ID

    Lcd_Log("\n %s HX8369A 0x%x , 0x%x , 0x%x \n",__func__,buffer[0],buffer[1],id);

    return (id == LCM_ID)?1:0;
#else
    Lcd_Log("mycat xxxxxx get_lcd_id=0x%x\n",get_lcd_id());
    return (get_lcd_id()==1)?1:0;
#endif
}

Example #19

0

Show file

File: r69338_hd720_dsi_vdo_jdi.c Project: Elnter/j608_kernel

/* VGP2 3.0v LDO enable */
static void ldo_3v0_on(void)
{

#ifdef BUILD_UBOOT 
	#error "not implemeted"
#elif defined(BUILD_LK)
    if ( g_PCBver==HW_REV_B )
    { 
    	upmu_set_rg_vgp2_vosel(6);  // VGP2_SEL= 101 : 2.8V , 110 : 3.0V
    	upmu_set_rg_vgp2_en(1);        
    }
    else if ( g_PCBver==HW_REV_A_2 )
    {
    	upmu_set_rg_vgp2_vosel(6);  // VGP2_SEL= 101 : 2.8V , 110 : 3.0V
    	upmu_set_rg_vgp2_en(1);	        
    }
    else    //( g_PCBver==HW_REV_A )
    {
        upmu_set_rg_vgp1_vosel(6);  // VGP2_SEL= 101 : 2.8V , 110 : 3.0V
        upmu_set_rg_vgp1_en(1);
    }    
#else
    if ( g_PCBver==HW_REV_B )
    {
    	hwPowerOn(MT6323_POWER_LDO_VGP2, VOL_3000, "3V0_MTK_LCD_VCC");	        
    }
    else if ( g_PCBver==HW_REV_A_2 )
    {
    	hwPowerOn(MT6323_POWER_LDO_VGP2, VOL_3000, "3V0_LCD_VCC_MTK_S");        
    }
    else    //( g_PCBver==HW_REV_A )
    {
	    hwPowerOn(MT6323_POWER_LDO_VGP1, VOL_3000, "3V0_TOUCH_VDD");	    
    }    
#endif

}

Example #20

0

Show file

File: ILI9488_QIJIA_FX350001S0_HSD_DSI_CMD_HVGA.c Project: SeriniTY320/mediatek

static unsigned int lcm_compare_id(void)
{
   unsigned int id = 0, id2 = 0;
    unsigned char buffer[3];
    unsigned int data_array[16];

#ifdef BUILD_LK
	upmu_set_rg_vgp2_vosel(5);
	upmu_set_rg_vgp2_en(1);

	upmu_set_rg_vgp3_vosel(3);
	upmu_set_rg_vgp3_en(1);	
#else
  hwPowerOn(MT6323_POWER_LDO_VGP2,VOL_2800,"LCM");
	hwPowerOn(MT6323_POWER_LDO_VGP3,VOL_1800,"LCM");
#endif
    MDELAY(100);

    SET_RESET_PIN(1);  //NOTE:should reset LCM firstly
    MDELAY(10);
    SET_RESET_PIN(0);
    MDELAY(50);
    SET_RESET_PIN(1);
    MDELAY(180);	
    

  /*  data_array[0]=0x00043902;
    data_array[1]=0x1698FFFF;
    dsi_set_cmdq(data_array, 2, 1);
    MDELAY(20); */
    
    data_array[0] = 0x00043700;// read id return two byte,version and id
    dsi_set_cmdq(data_array, 1, 1);
    MDELAY(20); 
    
    read_reg_v2(0xD3, buffer, 4);
    id = buffer[2]; //we only need ID
    id2= buffer[1] << 8 | buffer[2]; //we test buffer 1
    
 
    Lcd_Log("MYCAT ILI9806 A40318 %s, id=0x%x,id2=0x%x\n", __func__, id,id2);
 
 
    return (LCM_ID == id2)?1:0;
	//return 1;

	   // return (get_lcd_id()==1)?1:0;

}

Example #21

0

Show file

File: ili9806_HS045NK_35B_dsi_2_HUAYIN_wvga_cmd.c Project: SeriniTY320/mediatek

static unsigned int lcm_compare_id(void)
{
    unsigned int id = 0, id2 = 0;
    unsigned char buffer[3];
    unsigned int data_array[16];

#if defined(BUILD_LK)
	upmu_set_rg_vgp2_vosel(5);
	upmu_set_rg_vgp2_en(1);
#else
	hwPowerOn(MT6323_POWER_LDO_VGP2, VOL_2800, "Lance_LCM");
#endif
    MDELAY(100);

    SET_RESET_PIN(1);  //NOTE:should reset LCM firstly
    MDELAY(10);
    SET_RESET_PIN(0);
    MDELAY(10);
    SET_RESET_PIN(1);
    MDELAY(120);	
    
    /*	
    data_array[0] = 0x00110500;		// Sleep Out
    dsi_set_cmdq(data_array, 1, 1);
    MDELAY(120);
    */
    //*************Enable CMD2 Page1  *******************//
    data_array[0]=0x00043902;
    data_array[1]=0x1698FFFF;
    dsi_set_cmdq(data_array, 2, 1);
    MDELAY(20); 
    
    data_array[0] = 0x00033700;// read id return two byte,version and id
    dsi_set_cmdq(data_array, 1, 1);
    MDELAY(20); 
    
    read_reg_v2(0xD3, buffer, 3);
    id = buffer[1]; //we only need ID
    id2= buffer[1] << 8 | buffer[2]; //we test buffer 1
    
 
    Lcd_Log("MYCAT Read lcd id %s, id=0x%x,id2=0x%x\n", __func__, id,id2);
 
 
    return (LCM_ID == id2)?1:0;

	   // return (get_lcd_id()==1)?1:0;

}

Example #22

0

Show file

File: otm8018b_PUNAI_PT040WVH010A_HSD_dsi_2_wvga.c Project: SeriniTY320/mediatek

static unsigned int lcm_compare_id(void)
{
 
    int   array[4];
   char  buffer[5];
   char  id_high=0;
   char  id_low=0;
   int   id=0;

#ifdef BUILD_LK
    upmu_set_rg_vgp2_vosel(5);
    upmu_set_rg_vgp2_en(1);
    MDELAY(50);
    
    upmu_set_rg_vgp3_vosel(3);
    upmu_set_rg_vgp3_en(1); 
     
#else
    hwPowerOn(MT6323_POWER_LDO_VGP2,VOL_2800,"LCM28");
    hwPowerOn(MT6323_POWER_LDO_VGP3,VOL_1800,"LCM18");
#endif
    MDELAY(100);

   
   SET_RESET_PIN(1);  //NOTE:should reset LCM firstly
   SET_RESET_PIN(0);
   MDELAY(10);
   SET_RESET_PIN(1);
   MDELAY(10);
 
   array[0] = 0x00053700;// read id return two byte,version and id
   dsi_set_cmdq(array, 1, 1);
   read_reg_v2(0xA1,buffer, 5);
 
   id_high = buffer[2];            //should be 0x80
   Lcd_Log("%s, id_high = 0x%08x\n", __func__, id_high);
   id_low  = buffer[3];            //should be 0x18
   Lcd_Log("%s, id_low = 0x%08x\n", __func__, id_low);
   id      = (id_high<<8)|id_low;  //should be 0x8018
 
	 Lcd_Log("%s, id = 0x%08x\n", __func__, id); 
 
   return (LCM_ID == id&&get_lcd_id()==0)?1:0;
  // return (LCM_ID == id)?1:0;
   
   //return 1;
}

Example #23

0

Show file

File: ili9806E_jingtai_JTD050121S0_HSD_dsi_2_vdo_fwvga.c Project: SeriniTY320/mediatek

static void lcm_init(void)
{

		upmu_set_rg_vgp2_vosel(5);
		upmu_set_rg_vgp2_en(1);
		
		upmu_set_rg_vgp3_vosel(3);
		upmu_set_rg_vgp3_en(1);	

    SET_RESET_PIN(1);
    SET_RESET_PIN(0);
    MDELAY(50);
    SET_RESET_PIN(1);
    MDELAY(120);

	push_table(lcm_initialization_setting, sizeof(lcm_initialization_setting) / sizeof(struct LCM_setting_table), 1);
}

Example #24

0

Show file

File: otm8009a_haoshitong_HW397130_HSD_dsi_2_cmd_wvga.c Project: SeriniTY320/mediatek

static void lcm_resume(void)
{
#if 1
    push_table(lcm_sleep_out_setting, sizeof(lcm_sleep_out_setting) / sizeof(struct LCM_setting_table), 1);
#else

#ifndef BUILD_LK 
	lcm_init(); 
#else 
	upmu_set_rg_vgp2_vosel(5);
	upmu_set_rg_vgp2_en(1);

	upmu_set_rg_vgp3_vosel(3);
	upmu_set_rg_vgp3_en(1);	
 	MDELAY(100);
#endif 

#endif
}

Example #25

0

Show file

File: otm9605a_ykl_LP047APTP018A_V01_AUO_dsi_2_vdo_qhd.c Project: SeriniTY320/mediatek

static void lcm_suspend(void)
{
	push_table(lcm_deep_sleep_mode_in_setting, sizeof(lcm_deep_sleep_mode_in_setting) / sizeof(struct LCM_setting_table), 1);

 SET_RESET_PIN(0);
   MDELAY(1);
   SET_RESET_PIN(1);
#if defined(BUILD_LK)
	upmu_set_rg_vgp2_vosel(5);
	upmu_set_rg_vgp2_en(0);

	upmu_set_rg_vgp3_vosel(3);
	upmu_set_rg_vgp3_en(0);	
#else
	hwPowerDown(MT6323_POWER_LDO_VGP2, "Lance_LCM");
  hwPowerDown(MT6323_POWER_LDO_VGP3, "Lance_LCM");
#endif


}

Example #26

0

Show file

File: nt35517_rixin_NST446QH2538ANJ_CMI_dsi_qhd.c Project: SeriniTY320/mediatek

static unsigned int lcm_compare_id(void)
{
	unsigned int id = 0,id1=0,id2 = 0;
	unsigned char buffer[2]; 
	unsigned int data_array[16];
#if defined(BUILD_LK)
    upmu_set_rg_vgp2_vosel(5);
    upmu_set_rg_vgp2_en(1);

    upmu_set_rg_vgp3_vosel(3);
    upmu_set_rg_vgp3_en(1);
#else
    hwPowerOn(MT6323_POWER_LDO_VGP2, VOL_2800, "Lance_LCM");
    hwPowerOn(MT6323_POWER_LDO_VGP3, VOL_1800, "Lance_LCM");
#endif
    MDELAY(100);

	SET_RESET_PIN(1);  //NOTE:should reset LCM firstly 
	MDELAY(10); 
	SET_RESET_PIN(0);
	MDELAY(10); 
	SET_RESET_PIN(1); 
	MDELAY(10);        
	//*************Enable CMD2 Page1  *******************//
	
	data_array[0]=0x00063902;
	data_array[1]=0x52AA55F0;
	data_array[2]=0x00000108;
	dsi_set_cmdq(data_array, 3, 1); 
	MDELAY(10); 
	data_array[0] = 0x00023700;// read id return two byte,version and id
	dsi_set_cmdq(data_array, 1, 1); 
	MDELAY(10); 
	read_reg_v2(0xC5, buffer, 2); 
	id1 = buffer[0]; //we only need ID
	id2= buffer[1]; //we test buffer 1
	id = (id1<<8) | id2;
	return (0x5517 == id)?1:0;

}

Example #27

0

Show file

File: hx8389b_chuanglaiya_KQX5009E12_JDI_dsi_2_vdo_qhd.c Project: SeriniTY320/mediatek

static unsigned int lcm_compare_id(void)
{
	unsigned int id=0;
	unsigned char buffer[2];
	unsigned int array[16];  

#if defined(BUILD_LK)
	upmu_set_rg_vgp2_vosel(5);
	upmu_set_rg_vgp2_en(1);

	upmu_set_rg_vgp3_vosel(3);
	upmu_set_rg_vgp3_en(1);	
#else
	hwPowerOn(MT6323_POWER_LDO_VGP2, VOL_2800, "Lance_LCM");
       hwPowerOn(MT6323_POWER_LDO_VGP3, VOL_1800, "Lance_LCM");
#endif

	SET_RESET_PIN(1);
	MDELAY(5);
	SET_RESET_PIN(0);
	MDELAY(10);
	SET_RESET_PIN(1);
	MDELAY(150);//Must over 6 ms,SPEC request
	array[0]=0x00043902;
	array[1]=0x8983FFB9;// page enable
	dsi_set_cmdq(&array, 2, 1);
	MDELAY(10);

	array[0] = 0x00023700;// return byte number
	dsi_set_cmdq(&array, 1, 1);
	MDELAY(10);

	read_reg_v2(0xF4, buffer, 2);
	id = buffer[0]; 
	
#ifndef BUILD_LK
	printk("%s, id = 0x%02x, buf[1]=0x%02x\n", __func__, id,buffer[1]);
#endif
	return (LCM_ID_HX8389B == id)?1:0;
}

Example #28

0

Show file

File: ili9806e_jingtai_JTD040379B0_BOE_dsi_2_vdo_wvga.c Project: SeriniTY320/mediatek

static void lcm_init(void)
{
		unsigned int data_array[64];

#if defined(BUILD_LK)
		upmu_set_rg_vgp2_vosel(5);
		upmu_set_rg_vgp2_en(1);
		
		upmu_set_rg_vgp3_vosel(3);
		upmu_set_rg_vgp3_en(1);	
#else
		hwPowerOn(MT6323_POWER_LDO_VGP2, VOL_2800, "Lance_LCM");
		hwPowerOn(MT6323_POWER_LDO_VGP3, VOL_1800, "Lance_LCM");
#endif

    SET_RESET_PIN(1);
    SET_RESET_PIN(0);
    MDELAY(10);//Must > 10ms
    SET_RESET_PIN(1);
    MDELAY(100);//Must > 120ms

	push_table(lcm_initialization_setting, sizeof(lcm_initialization_setting) / sizeof(struct LCM_setting_table), 1);
}

Example #29

0

Show file

File: hx8389b_chuanglaiya_KQX5009E12_JDI_dsi_2_vdo_qhd.c Project: SeriniTY320/mediatek

static void lcm_init(void)
{
	#if defined(BUILD_LK)
	upmu_set_rg_vgp2_vosel(5);
	upmu_set_rg_vgp2_en(1);

	upmu_set_rg_vgp3_vosel(3);
	upmu_set_rg_vgp3_en(1);	
#else
	hwPowerOn(MT6323_POWER_LDO_VGP2, VOL_2800, "Lance_LCM");
       hwPowerOn(MT6323_POWER_LDO_VGP3, VOL_1800, "Lance_LCM");
#endif

	SET_RESET_PIN(1);
	MDELAY(5);
	SET_RESET_PIN(0);
	MDELAY(10);
	SET_RESET_PIN(1);
	MDELAY(150);//Must over 6 ms,SPEC request
	lcm_init_setting();
	
	/////push_table(lcm_initialization_setting, sizeof(lcm_initialization_setting) / sizeof(struct LCM_setting_table), 1);
}

Example #30

0

Show file

File: RM68171_QICAI_K40BM231423A1N_BOE_DSI_2_WVGA_VDO.c Project: SeriniTY320/mediatek

static void lcm_init(void)
{
	#if defined(BUILD_LK)
		upmu_set_rg_vgp2_vosel(5);
		upmu_set_rg_vgp2_en(1);
		
		upmu_set_rg_vgp3_vosel(3);
		upmu_set_rg_vgp3_en(1);	
#else
		hwPowerOn(MT6323_POWER_LDO_VGP2, VOL_2800, "Lance_LCM");
		hwPowerOn(MT6323_POWER_LDO_VGP3, VOL_1800, "Lance_LCM");
#endif
  SET_RESET_PIN(1);
  SET_RESET_PIN(0);
  MDELAY(50);//Must > 5ms
  SET_RESET_PIN(1);
  MDELAY(120);//Must > 50ms

	Lcd_Log("wqcat RM68171_zhuoershi_Z40252N00I4OMA_BOE_DSI_2_WVGA_VDO lcm init\n");
	
	//init_lcm_registers();
	push_table(lcm_initialization_setting, sizeof(lcm_initialization_setting) / sizeof(struct LCM_setting_table), 1);
}