/*!
* Radio Initialization.
*
* @author Sz. Papp
*
* @note
*
*/
void vRadio_Init(void)
{
/* Power Up the radio chip */
vRadio_PowerUp();
/* Load radio configuration */
while (SI446X_SUCCESS != si446x_configuration_init(pRadioConfiguration->Radio_ConfigurationArray))
{
/* Error hook */
BSP_LedSet(0);
Delay(2);
BSP_LedClear(0);
/* Power Up the radio chip */
vRadio_PowerUp();
}
// Read ITs, clear pending ones
si446x_get_int_status(0u, 0u, 0u);
}
/*!
* Radio Initialization.
*
* @author Sz. Papp
*
* @note
*
*/
void vRadio_Init(void)
{
U16 wDelay;
/* Power Up the radio chip */
vRadio_PowerUp();
/* Load radio configuration */
while (SI446X_SUCCESS != si446x_configuration_init(pRadioConfiguration->Radio_ConfigurationArray))
{
/* Error hook */
for (wDelay = 0x7FFF; wDelay--; ) ;
/* Power Up the radio chip */
vRadio_PowerUp();
}
// Read ITs, clear pending ones
si446x_get_int_status(0u, 0u, 0u);
}
void vRadio_Init(void)
{
U16 wDelay;
/* Power Up the radio chip */
vRadio_PowerUp();
/* Load radio configuration */
while (SI446X_SUCCESS != si446x_configuration_init(pRadioConfiguration->Radio_ConfigurationArray))
{
for (wDelay = 0x7FFF; wDelay--; ) ;
/* Power Up the radio chip */
vRadio_PowerUp();
}
// Read ITs, clear pending ones
si446x_get_int_status(0u, 0u, 0u);
si446x_fifo_info(SI446X_CMD_FIFO_INFO_ARG_RX_BIT);
}
/*!
* Radio Initialization.
*
* @author Sz. Papp
*
* @note
*
*/
void vRadio_Init(void)
{
U16 wDelay;
/* Power Up the radio chip */
vRadio_PowerUp();
/* Load radio configuration */
while (SI446X_SUCCESS != si446x_configuration_init(pRadioConfiguration->Radio_ConfigurationArray))
{
/* Error hook */
#if !(defined SILABS_PLATFORM_WMB912)
LED4 = !LED4;
#else
vCio_ToggleLed(eHmi_Led4_c);
#endif
for (wDelay = 0x7FFF; wDelay--; ) ;
/* Power Up the radio chip */
vRadio_PowerUp();
}
// Read ITs, clear pending ones
si446x_get_int_status(0u, 0u, 0u);
}
/*!
* Radio Initialization.
*
* @author Sz. Papp
*
* @note
*
*/
void vRadio_Init(void)
{
U16 lTemp;
#if (RADIO_CONFIGURATION_DATA_RADIO_PATCH_INCLUDED > 0x00)
const SEGMENT_VARIABLE(RadioPatch[RADIO_CONFIGURATION_DATA_RADIO_PATCH_SIZE], U8, SEG_CODE) = \
RADIO_CONFIGURATION_DATA_RADIO_PATCH;
#endif
do
{
/* Power Up the radio chip */
vRadio_PowerUp();
/* Load the 1st part of the configuration array (128 bytes) */
si4455_write_ezconfig_array(128u, pRadioConfiguration->EzConfig_Array);
/* Delay between two part to let the radio process the incoming data */
for (lTemp = 0x07FF; lTemp; lTemp--) ;
/* Load the final part of the configuration array (128 bytes) */
si4455_write_ezconfig_array(EZCONFIG_RADIO_CFG_SIZE - 128u, (U8 *) pRadioConfiguration->EzConfig_Array + 128u);
lTemp = bRadio_Check_Ezconfig(pRadioConfiguration->EzConfig_Array_CRC);
/* Check the return value */
if (lTemp == 1u) { LED4 = !LED4; }
if (lTemp == 2u) { LED3 = !LED3; }
} while(lTemp != 0u);
// Read ITs, clear pending ones
si4455_get_int_status(0u, 0u, 0u);
/* Set XO TUNE */
si4455_set_property(
SI4455_PROP_GRP_ID_EZCONFIG,
SI4455_PROP_GRP_LEN_EZCONFIG,
SI4455_PROP_GRP_INDEX_EZCONFIG_XO_TUNE,
(U8) pRadioConfiguration->Radio_EZCONFIG_XO_TUNE
);
/* Enable ITs */
si4455_set_property(
SI4455_PROP_GRP_ID_INT_CTL,
SI4455_PROP_GRP_LEN_INT_CTL,
SI4455_PROP_GRP_INDEX_INT_CTL_ENABLE,
(U8) pRadioConfiguration->Radio_INT_CTL_ENABLE,
(U8) pRadioConfiguration->Radio_INT_CTL_PH_ENABLE,
(U8) pRadioConfiguration->Radio_INT_CTL_MODEM_ENABLE,
(U8) pRadioConfiguration->Radio_INT_CTL_CHIP_ENABLE
);
// Configure Fast response registers
si4455_set_property(
SI4455_PROP_GRP_ID_FRR_CTL,
SI4455_PROP_GRP_LEN_FRR_CTL,
SI4455_PROP_GRP_INDEX_FRR_CTL_A_MODE,
(U8) pRadioConfiguration->Radio_FRR_CTL_A_MODE,
(U8) pRadioConfiguration->Radio_FRR_CTL_B_MODE,
(U8) pRadioConfiguration->Radio_FRR_CTL_C_MODE,
(U8) pRadioConfiguration->Radio_FRR_CTL_D_MODE
);
// Configure GPIO pins
si4455_gpio_pin_cfg(
pRadioConfiguration->Radio_GPIO0_PIN_CFG,
pRadioConfiguration->Radio_GPIO1_PIN_CFG,
pRadioConfiguration->Radio_GPIO2_PIN_CFG,
pRadioConfiguration->Radio_GPIO3_PIN_CFG,
pRadioConfiguration->Radio_GPIO_NIRQ_MODE,
pRadioConfiguration->Radio_GPIO_SDO_MODE,
pRadioConfiguration->Radio_GPIO_GEN_CONFIG
);
// Put the Radio into configured state
si4455_change_state(pRadioConfiguration->Radio_State_After_Power_Up);
// Read ITs, clear pending ones
si4455_get_int_status(0u, 0u, 0u);
}