int main( void )
{
/* The examples assume that all priority bits are assigned as preemption
priority bits. */
NVIC_SetPriorityGrouping( 0UL );
/* Start the timers that demonstrate FreeRTOS software timers and basic
GPIO functionality. */
vGPIOSoftwareTimersStart();
/* Start the tasks that implements the command console on the UART, as
described above. */
vUARTCommandConsoleStart();
/* Start the task that demonstrates the SSP port being used in SPI mode to
write to the 7 segment display. */
vSPIWriteTaskStart();
/* Start the task that uses an I2C peripheral to communicate with the
OLED and the EEPROM. */
vI2CTaskStart();
/* Register two command line commands to show task stats and run time stats
respectively. */
vRegisterCLICommands();
/* Start the FreeRTOS scheduler. */
vTaskStartScheduler();
/* The following line should never execute. If it does, it means there was
insufficient FreeRTOS heap memory available to create the Idle and/or timer
tasks. See the memory management section on the http://www.FreeRTOS.org web
site for more information. */
for( ;; );
}
void main_full( void )
{
/* This demo sets the clock to its maximum. The blinky demo uses as slower
clock as it uses low power features. */
prvConfigureClocks();
/* Init the serial port for use by the CLI. The baud rate parameter is not
used so set to 0 to make this obvious. */
xSerialPortInitMinimal( 0, mainRX_QUEUE_LENGTH );
/* Start all the other standard demo/test tasks. They have no particular
functionality, but do demonstrate how to use the FreeRTOS API and test the
kernel port. */
vStartInterruptQueueTasks();
vStartCountingSemaphoreTasks();
vStartGenericQueueTasks( tskIDLE_PRIORITY );
vStartRecursiveMutexTasks();
vStartSemaphoreTasks( mainSEM_TEST_PRIORITY );
vStartTimerDemoTask( mainTIMER_TEST_PERIOD );
vStartEventGroupTasks();
vStartTaskNotifyTask();
vStartInterruptSemaphoreTasks();
/* Note - the set of standard demo tasks contains two versions of
vStartMathTasks.c. One is defined in flop.c, and uses double precision
floating point numbers and variables. The other is defined in sp_flop.c,
and uses single precision floating point numbers and variables. sp_flop.
c should be included in this project. */
vStartMathTasks( mainFLOP_TASK_PRIORITY );
/* Start the tasks that implements the command console on the UART, as
described above. */
vUARTCommandConsoleStart( mainUART_COMMAND_CONSOLE_STACK_SIZE, mainUART_COMMAND_CONSOLE_TASK_PRIORITY );
/* Register the standard CLI commands. */
vRegisterSampleCLICommands();
/* Create the register check tasks, as described at the top of this file */
xTaskCreate( prvRegTestTaskEntry1, "Reg1", configMINIMAL_STACK_SIZE, mainREG_TEST_TASK_1_PARAMETER, tskIDLE_PRIORITY, NULL );
xTaskCreate( prvRegTestTaskEntry2, "Reg2", configMINIMAL_STACK_SIZE, mainREG_TEST_TASK_2_PARAMETER, tskIDLE_PRIORITY, NULL );
/* Create the task that performs the 'check' functionality, as described at
the top of this file. */
xTaskCreate( prvCheckTask, "Check", configMINIMAL_STACK_SIZE, NULL, mainCHECK_TASK_PRIORITY, NULL );
/* Start the scheduler. */
vTaskStartScheduler();
/* If all is well, the scheduler will now be running, and the following
line will never be reached. If the following line does execute, then
there was either insufficient FreeRTOS heap memory available for the idle
and/or timer tasks to be created, or vTaskStartScheduler() was called from
User mode. See the memory management section on the FreeRTOS web site for
more details on the FreeRTOS heap http://www.freertos.org/a00111.html. The
mode from which main() is called is set in the C start up code and must be
a privileged mode (not user mode). */
for( ;; );
}
void main_full( void )
{
TimerHandle_t xCheckTimer = NULL;
/* Prepare to run the full demo: Configure the IO, register the CLI
commands, and depending on configuration, generate a set of sample files on
a RAM disk. */
prvPrepareForFullDemo();
/* Start all the other standard demo/test tasks. The have not particular
functionality, but do demonstrate how to use the FreeRTOS API and test the
kernel port. */
vStartIntegerMathTasks( tskIDLE_PRIORITY );
vStartDynamicPriorityTasks();
vStartBlockingQueueTasks( mainBLOCK_Q_PRIORITY );
vCreateBlockTimeTasks();
vStartCountingSemaphoreTasks();
vStartGenericQueueTasks( tskIDLE_PRIORITY );
vStartRecursiveMutexTasks();
vStartPolledQueueTasks( mainQUEUE_POLL_PRIORITY );
vStartSemaphoreTasks( mainSEM_TEST_PRIORITY );
vStartLEDFlashTimers( mainNUMBER_OF_FLASH_TIMERS_LEDS );
/* Start the tasks that implements the command console on the UART, as
described above. */
vUARTCommandConsoleStart( mainUART_COMMAND_CONSOLE_STACK_SIZE, mainUART_COMMAND_CONSOLE_TASK_PRIORITY );
/* Create the software timer that performs the 'check' functionality,
as described at the top of this file. */
xCheckTimer = xTimerCreate( "CheckTimer", /* A text name, purely to help debugging. */
( mainCHECK_TIMER_PERIOD_MS ), /* The timer period, in this case 3000ms (3s). */
pdTRUE, /* This is an auto-reload timer, so xAutoReload is set to pdTRUE. */
( void * ) 0, /* The ID is not used, so can be set to anything. */
prvCheckTimerCallback /* The callback function that inspects the status of all the other tasks. */
);
if( xCheckTimer != NULL )
{
xTimerStart( xCheckTimer, mainDONT_BLOCK );
}
/* The set of tasks created by the following function call have to be
created last as they keep account of the number of tasks they expect to see
running. */
vCreateSuicidalTasks( mainCREATOR_TASK_PRIORITY );
/* Start the scheduler. */
vTaskStartScheduler();
/* If all is well, the scheduler will now be running, and the following line
will never be reached. If the following line does execute, then there was
insufficient FreeRTOS heap memory available for the idle and/or timer tasks
to be created. See the memory management section on the FreeRTOS web site
for more details. */
for( ;; );
}
void main_full( void )
{
/* Start all the other standard demo/test tasks. They have no particular
functionality, but do demonstrate how to use the FreeRTOS API and test the
kernel port. */
vStartDynamicPriorityTasks();
vCreateBlockTimeTasks();
vStartCountingSemaphoreTasks();
vStartGenericQueueTasks( tskIDLE_PRIORITY );
vStartRecursiveMutexTasks();
vStartSemaphoreTasks( mainSEM_TEST_PRIORITY );
vStartTimerDemoTask( mainTIMER_TEST_PERIOD );
vStartEventGroupTasks();
vStartTaskNotifyTask();
vStartInterruptSemaphoreTasks();
/* Note - the set of standard demo tasks contains two versions of
vStartMathTasks.c. One is defined in flop.c, and uses double precision
floating point numbers and variables. The other is defined in sp_flop.c,
and uses single precision floating point numbers and variables. The
MicroBlaze floating point unit only handles single precision floating.
Therefore, to test the floating point hardware, sp_flop.c should be included
in this project. */
vStartMathTasks( mainFLOP_TASK_PRIORITY );
/* Start the tasks that implements the command console on the UART, as
described above. */
vUARTCommandConsoleStart( mainUART_COMMAND_CONSOLE_STACK_SIZE, mainUART_COMMAND_CONSOLE_TASK_PRIORITY );
/* Register the standard CLI commands. */
vRegisterSampleCLICommands();
/* Create the register check tasks, as described at the top of this file */
xTaskCreate( prvRegTestTaskEntry1, "Reg1", configMINIMAL_STACK_SIZE, mainREG_TEST_TASK_1_PARAMETER, tskIDLE_PRIORITY, NULL );
xTaskCreate( prvRegTestTaskEntry2, "Reg2", configMINIMAL_STACK_SIZE, mainREG_TEST_TASK_2_PARAMETER, tskIDLE_PRIORITY, NULL );
/* Create the task that performs the 'check' functionality, as described at
the top of this file. */
xTaskCreate( prvCheckTask, "Check", configMINIMAL_STACK_SIZE, NULL, mainCHECK_TASK_PRIORITY, NULL );
/* Start the scheduler. */
vTaskStartScheduler();
/* If all is well, the scheduler will now be running, and the following
line will never be reached. If the following line does execute, then
there was insufficient FreeRTOS heap memory available for the Idle and/or
timer tasks to be created. See the memory management section on the
FreeRTOS web site for more details on the FreeRTOS heap
http://www.freertos.org/a00111.html. */
for( ;; );
}
void main_full( void )
{
/* Start all the standard demo/test tasks. They have no particular
functionality, but do demonstrate how to use the FreeRTOS API and test the
kernel port. */
vStartDynamicPriorityTasks();
vCreateBlockTimeTasks();
vStartCountingSemaphoreTasks();
vStartGenericQueueTasks( tskIDLE_PRIORITY );
vStartRecursiveMutexTasks();
vStartEventGroupTasks();
vStartTaskNotifyTask();
/* Create the register check tasks, as described at the top of this file */
xTaskCreate( prvRegTestTaskEntry1, /* Task entry point. */
"Reg1", /* Text name for the task - not used by the kernel. */
configMINIMAL_STACK_SIZE, /* Stack to allocate to the task - in words not bytes! */
mainREG_TEST_TASK_1_PARAMETER, /* The parameter passed into the task. */
tskIDLE_PRIORITY, /* The task's priority. */
NULL ); /* Task handle is not needed, so NULL is passed. */
xTaskCreate( prvRegTestTaskEntry2, "Reg2", configMINIMAL_STACK_SIZE, mainREG_TEST_TASK_2_PARAMETER, tskIDLE_PRIORITY, NULL );
/* Create the task that performs the 'check' functionality, as described at
the top of this file. */
xTaskCreate( prvCheckTask, "Check", configMINIMAL_STACK_SIZE, NULL, mainCHECK_TASK_PRIORITY, NULL );
/* Register an example set of CLI commands, then start the task that manages
the CLI using a UART for input and output. */
vRegisterSampleCLICommands();
vUARTCommandConsoleStart( mainCOMMAND_CONSOLE_STACK_SIZE, mainCOMMAND_CONSOLE_TASK_PRIORITY );
/* Start the scheduler. */
vTaskStartScheduler();
/* If all is well, the scheduler will now be running, and the following
line will never be reached. If the following line does execute, then
there was either insufficient FreeRTOS heap memory available for the idle
and/or timer tasks to be created. See the memory management section on the
FreeRTOS web site for more details on the FreeRTOS heap
http://www.freertos.org/a00111.html. */
for( ;; );
}
/* Init FreeRTOS */
void MX_FREERTOS_Init(void)
{
/* Create a defaultTask */
xTaskCreate(StartDefaultTask, (const char *) "DefaultTask", configMINIMAL_STACK_SIZE, NULL, osPriorityNormal, &defaultTaskHandle);
/* Create tasks for module ports */
xTaskCreate(PxTask, (const char *) "P1Task", configMINIMAL_STACK_SIZE, (void *) P1, osPriorityNormal, &P1TaskHandle);
xTaskCreate(PxTask, (const char *) "P2Task", configMINIMAL_STACK_SIZE, (void *) P2, osPriorityNormal, &P2TaskHandle);
xTaskCreate(PxTask, (const char *) "P3Task", configMINIMAL_STACK_SIZE, (void *) P3, osPriorityNormal, &P3TaskHandle);
xTaskCreate(PxTask, (const char *) "P4Task", configMINIMAL_STACK_SIZE, (void *) P4, osPriorityNormal, &P4TaskHandle);
xTaskCreate(PxTask, (const char *) "P5Task", configMINIMAL_STACK_SIZE, (void *) P5, osPriorityNormal, &P5TaskHandle);
#if (HO01R1 || HO02R0 || HO01R2 || HO02R1 || HO01R3 || HO02R2)
xTaskCreate(PxTask, (const char *) "P6Task", configMINIMAL_STACK_SIZE, (void *) P6, osPriorityNormal, &P6TaskHandle);
#endif
/* Create the front-end task */
xTaskCreate(FrontEndTask, (const char *) "FrontEndTask", configMINIMAL_STACK_SIZE, NULL, osPriorityAboveNormal, &FrontEndTaskHandle);
/* Create the motor continuous rotation task */
// xTaskCreate(ContRotationTask, (const char *) "ContRotationTask", configMINIMAL_STACK_SIZE, NULL, osPriorityAboveNormal, &ContRotationHandle);
/* Create semaphores to protect module ports (FreeRTOS vSemaphoreCreateBinary didn't work) */
osSemaphoreDef(SemaphoreP1); PxSemaphoreHandle[P1] = osSemaphoreCreate(osSemaphore(SemaphoreP1), 1);
osSemaphoreDef(SemaphoreP2); PxSemaphoreHandle[P2] = osSemaphoreCreate(osSemaphore(SemaphoreP2), 1);
osSemaphoreDef(SemaphoreP3); PxSemaphoreHandle[P3] = osSemaphoreCreate(osSemaphore(SemaphoreP3), 1);
osSemaphoreDef(SemaphoreP4); PxSemaphoreHandle[P4] = osSemaphoreCreate(osSemaphore(SemaphoreP4), 1);
osSemaphoreDef(SemaphoreP5); PxSemaphoreHandle[P5] = osSemaphoreCreate(osSemaphore(SemaphoreP5), 1);
#if (HO01R1 || HO02R0 || HO01R2 || HO02R1 || HO01R3 || HO02R2)
osSemaphoreDef(SemaphoreP6); PxSemaphoreHandle[P6] = osSemaphoreCreate(osSemaphore(SemaphoreP6), 1);
#endif
/* Register command line commands */
vRegisterCLICommands();
/* Start the tasks that implements the command console on the UART */
vUARTCommandConsoleStart();
}
void main_full( void )
{
xTimerHandle xTimer = NULL;
/* The register test tasks are asm functions that don't use a stack. The
stack allocated just has to be large enough to hold the task context, and
for the additional required for the stack overflow checking to work (if
configured). */
const size_t xRegTestStackSize = 25U;
/* Create the standard demo tasks */
vCreateBlockTimeTasks();
vStartDynamicPriorityTasks();
vStartCountingSemaphoreTasks();
vStartRecursiveMutexTasks();
vStartQueueOverwriteTask( tskIDLE_PRIORITY );
vStartQueueSetTasks();
vStartGenericQueueTasks( tskIDLE_PRIORITY );
vStartQueuePeekTasks();
/* Start the task that manages the command console for FreeRTOS+CLI. */
vUARTCommandConsoleStart( ( configMINIMAL_STACK_SIZE * 3 ), tskIDLE_PRIORITY );
/* Create the register test tasks as described at the top of this file.
These are naked functions that don't use any stack. A stack still has
to be allocated to hold the task context. */
xTaskCreate( vRegTest1Task, /* Function that implements the task. */
( signed char * ) "Reg1", /* Text name of the task. */
xRegTestStackSize, /* Stack allocated to the task. */
NULL, /* The task parameter is not used. */
tskIDLE_PRIORITY, /* The priority to assign to the task. */
NULL ); /* Don't receive a handle back, it is not needed. */
xTaskCreate( vRegTest2Task, /* Function that implements the task. */
( signed char * ) "Reg2", /* Text name of the task. */
xRegTestStackSize, /* Stack allocated to the task. */
NULL, /* The task parameter is not used. */
tskIDLE_PRIORITY, /* The priority to assign to the task. */
NULL ); /* Don't receive a handle back, it is not needed. */
/* Create the software timer that performs the 'check' functionality,
as described at the top of this file. */
xTimer = xTimerCreate( ( const signed char * ) "CheckTimer",/* A text name, purely to help debugging. */
( mainCHECK_TIMER_PERIOD_MS ), /* The timer period, in this case 3000ms (3s). */
pdTRUE, /* This is an auto-reload timer, so xAutoReload is set to pdTRUE. */
( void * ) 0, /* The ID is not used, so can be set to anything. */
prvCheckTimerCallback /* The callback function that inspects the status of all the other tasks. */
);
/* If the software timer was created successfully, start it. It won't
actually start running until the scheduler starts. A block time of
zero is used in this call, although any value could be used as the block
time will be ignored because the scheduler has not started yet. */
configASSERT( xTimer );
if( xTimer != NULL )
{
xTimerStart( xTimer, mainDONT_BLOCK );
}
/* Start the kernel. From here on, only tasks and interrupts will run. */
vTaskStartScheduler();
/* If all is well, the scheduler will now be running, and the following
line will never be reached. If the following line does execute, then there
was insufficient FreeRTOS heap memory available for the idle and/or timer
tasks to be created. See the memory management section on the FreeRTOS web
site, or the FreeRTOS tutorial books for more details. */
for( ;; );
}
void main_full( void )
{
/* The baud rate setting here has no effect, hence it is set to 0 to
make that obvious. */
xSerialPortInitMinimal( 0, mainUART_QUEUE_LENGTHS );
/* If the file system is only going to be accessed from one task then
F_FS_THREAD_AWARE can be set to 0 and the set of example files are created
before the RTOS scheduler is started. If the file system is going to be
access from more than one task then F_FS_THREAD_AWARE must be set to 1 and
the set of sample files are created from the idle task hook function
vApplicationIdleHook() - which is defined in this file. */
#if ( mainINCLUDE_FAT_SL_DEMO == 1 )&& ( F_FS_THREAD_AWARE == 0 )
{
/* Initialise the drive and file system, then create a few example
files. The output from this function just goes to the stdout window,
allowing the output to be viewed when the UDP command console is not
connected. */
vCreateAndVerifySampleFiles();
}
#endif
/* Start all the other standard demo/test tasks. The have not particular
functionality, but do demonstrate how to use the FreeRTOS API and test the
kernel port. */
vStartDynamicPriorityTasks();
vStartBlockingQueueTasks( mainBLOCK_Q_PRIORITY );
vCreateBlockTimeTasks();
vStartCountingSemaphoreTasks();
vStartGenericQueueTasks( tskIDLE_PRIORITY );
vStartRecursiveMutexTasks();
vStartSemaphoreTasks( mainSEM_TEST_PRIORITY );
vStartMathTasks( mainFLOP_TASK_PRIORITY );
vStartTimerDemoTask( mainTIMER_TEST_PERIOD );
vStartQueueOverwriteTask( mainQUEUE_OVERWRITE_PRIORITY );
#if mainINCLUDE_FAT_SL_DEMO == 1
{
/* Start the tasks that implements the command console on the UART, as
described above. */
vUARTCommandConsoleStart( mainUART_COMMAND_CONSOLE_STACK_SIZE, mainUART_COMMAND_CONSOLE_TASK_PRIORITY );
/* Register both the standard and file system related CLI commands. */
vRegisterSampleCLICommands();
vRegisterFileSystemCLICommands();
}
#else
{
/* The COM test tasks can use the UART if the CLI is not used by the
FAT SL demo. The COM test tasks require a UART connector to be fitted
to the UART port. */
vAltStartComTestTasks( mainCOM_TEST_TASK_PRIORITY, mainBAUD_RATE, mainCOM_TEST_LED );
}
#endif
/* Create the register check tasks, as described at the top of this
file */
xTaskCreate( prvRegTestTaskEntry1, ( signed char * ) "Reg1", configMINIMAL_STACK_SIZE, mainREG_TEST_TASK_1_PARAMETER, tskIDLE_PRIORITY, NULL );
xTaskCreate( prvRegTestTaskEntry2, ( signed char * ) "Reg2", configMINIMAL_STACK_SIZE, mainREG_TEST_TASK_2_PARAMETER, tskIDLE_PRIORITY, NULL );
/* Create the task that performs the 'check' functionality, as described at
the top of this file. */
xTaskCreate( prvCheckTask, ( signed char * ) "Check", configMINIMAL_STACK_SIZE, NULL, mainCHECK_TASK_PRIORITY, NULL );
/* The set of tasks created by the following function call have to be
created last as they keep account of the number of tasks they expect to see
running. */
vCreateSuicidalTasks( mainCREATOR_TASK_PRIORITY );
/* Start the scheduler. */
vTaskStartScheduler();
/* If all is well, the scheduler will now be running, and the following
line will never be reached. If the following line does execute, then
there was either insufficient FreeRTOS heap memory available for the idle
and/or timer tasks to be created, or vTaskStartScheduler() was called from
User mode. See the memory management section on the FreeRTOS web site for
more details on the FreeRTOS heap http://www.freertos.org/a00111.html. The
mode from which main() is called is set in the C start up code and must be
a privileged mode (not user mode). */
for( ;; );
}
