RobotDemo(void):
myRobot(2, 3), // these must be initialized in the same order
stick(1), // as they are declared above.
vic(1)
{
myRobot.SetExpiration(0.1);
}
RobotDemo(void)
{
kicker_in_motion = false;
sol = new Solenoid(2);
rightstick = new Joystick(1);
leftstick = new Joystick(2);
lonelystick = new Joystick (3);
Motor1=new Jaguar(1);
Motor2=new Jaguar(2);
Motor3=new Jaguar(3);
Motor4=new Jaguar(4);
BallGathererMotor9 = new Jaguar(9);
myRobot=new RobotDrive(Motor1,Motor2,Motor4,Motor3);
rlyLED=new Relay(8,Relay::kForwardOnly);
cam = &AxisCamera::GetInstance("10.8.12.11");
cam->WriteResolution(AxisCameraParams::kResolution_160x120);
myRobot->SetExpiration(0.5);
ControllBox = & DriverStation::GetInstance()->GetEnhancedIO();
shooter1 = new Jaguar(5); //front left
shooter2 = new Jaguar(6);
shooter3 = new Jaguar(7);
shooter4 = new Jaguar(8);
//shooterDin = new DigitalInput(1);
shootercontador = new Counter(1);
shootercontador->Start();
shooterspeedTask = new Task("ShooterSpeed",(FUNCPTR)&shooterspeedloop);
kickerTask = new Task ("Kicker", (FUNCPTR)&kickerloop);
Upperlimit = new DigitalInput(3);
Lowerlimit = new DigitalInput(2);
kickermotor = new Relay (6, Relay::kBothDirections);
BridgeBootMotor10 = new Jaguar(10);
kicker_cancel = false;
kicker_down = false;
}
RobotDemo():
myRobot(1, 2), // these must be initialized in the same order
stick(1) // as they are declared above.
{
cout << "Good morning!" << endl;
myRobot.SetExpiration(0.1);
}
RobotDemo():
myRobot(1, 2), // these must be initialized in the same order
stick(1) // as they are declared above.
{
myRobot.SetExpiration(0.1);
this->SetPeriod(0); //Set update period to sync with robot control packets (20ms nominal)
}
Robot() :
timer(),
robotDrive(Constants::driveFrontLeftPin, Constants::driveRearLeftPin, Constants::driveFrontRightPin, Constants::driveRearRightPin),//tells the robot where everything is plugged in
i2c(I2C::kOnboard,Constants::ledAddress),
driveStick(Constants::driveStickChannel),
grabStick(Constants::grabStickChannel),
prox(Constants::driveUltrasonicPin),
grabTalon(Constants::grabTalonPin),
grabInnerLimit(Constants::grabInnerLimitPin),
grabOuterLimit(Constants::grabOuterLimitPin),
liftTalon(Constants::liftTalonPin),
liftEncoder(Constants::liftEncoderAPin, Constants::liftEncoderBPin),
liftUpperLimit(Constants::liftUpperLimitPin),
liftLowerLimit(Constants::liftLowerLimitPin),
grabEncoder(Constants::grabEncoderAPin, Constants::grabEncoderBPin),
pdp(),
gyro(Constants::driveGyroRate),
pickup(grabTalon, grabInnerLimit, grabOuterLimit, liftTalon, liftEncoder, liftUpperLimit, liftLowerLimit, pdp)
{
robotDrive.SetExpiration(0.1); // safety feature
robotDrive.SetInvertedMotor(RobotDrive::kFrontRightMotor, true); // make the motors go the right way
robotDrive.SetInvertedMotor(RobotDrive::kRearRightMotor, true);
robotDrive.SetInvertedMotor(RobotDrive::kRearLeftMotor, true);
liftEncoder.SetReverseDirection(Constants::liftEncoderReverse);
}
Robot() :
myRobot(0, 1), // these must be initialized in the same order
joystick(0), // as they are declared above.
crochets(2)
{
myRobot.SetExpiration(0.1);
}
RobotDemo(void):
myRobot(LEFT_DRIVE_PWM, RIGHT_DRIVE_PWM), // these must be initialized in the same order
stick(1), // as they are declared above.
stick2(2),
gamepad(3),
collectorMotor(PICKUP_PWM),
indexerMotor(INDEX_PWM),
shooterMotor(SHOOTER_PWM),
armMotor (ARM_PWM),
shifter(SHIFTER_A,SHIFTER_B),
greenClaw(CLAW_1_LOCKED, CLAW_1_UNLOCKED),
yellowClaw(CLAW_2_LOCKED, CLAW_2_UNLOCKED),
potentiometer(ARM_ROTATION_POT),
indexSwitch(INDEXER_SW),
compressor(COMPRESSOR_PRESSURE_SW, COMPRESSOR_SPIKE)
{
m_collectorMotorRunning = false;
m_shooterMotorRunning = false;
dsLCD = DriverStationLCD::GetInstance();
dsLCD->PrintfLine(DriverStationLCD::kUser_Line1, "2013 " NAME);
dsLCD->PrintfLine(DriverStationLCD::kUser_Line2, __DATE__ " "__TIME__);
dsLCD->UpdateLCD();
myRobot.SetExpiration(0.1);
shifter.Set(DoubleSolenoid::kReverse);
}
RobotDemo(void):
myRobot(1,2), // these must be initialized in the same order
newStick(1)
{
myRobot.SetExpiration(0.1);
}
Robot() :
robotDrive(frontLeftChannel, rearLeftChannel,
frontRightChannel, rearRightChannel), // initialize variables in same
stick(joystickChannel) // order as declared above.
{
rotateToAngleRate = 0.0f;
robotDrive.SetExpiration(0.1);
robotDrive.SetInvertedMotor(RobotDrive::kFrontLeftMotor, true); // invert left side motors
robotDrive.SetInvertedMotor(RobotDrive::kRearLeftMotor, true); // change to match your robot
try {
/* Communicate w/navX MXP via the MXP SPI Bus. */
/* Alternatively: I2C::Port::kMXP, SerialPort::Port::kMXP or SerialPort::Port::kUSB */
/* See http://navx-mxp.kauailabs.com/guidance/selecting-an-interface/ for details. */
ahrs = new AHRS(SPI::Port::kMXP);
} catch (std::exception ex ) {
std::string err_string = "Error instantiating navX MXP: ";
err_string += ex.what();
DriverStation::ReportError(err_string.c_str());
}
turnController = new PIDController(kP, kI, kD, kF, ahrs, this);
turnController->SetInputRange(-180.0f, 180.0f);
turnController->SetOutputRange(-1.0, 1.0);
turnController->SetAbsoluteTolerance(kToleranceDegrees);
turnController->SetContinuous(true);
/* Add the PID Controller to the Test-mode dashboard, allowing manual */
/* tuning of the Turn Controller's P, I and D coefficients. */
/* Typically, only the P value needs to be modified. */
LiveWindow::GetInstance()->AddActuator("DriveSystem", "RotateController", turnController);
if ( ahrs ) {
LiveWindow::GetInstance()->AddSensor("IMU", "Gyro", ahrs);
}
}
RobotDemo(void)
// these must be initialized in the same order, ports 8 and nine are not being used
{
/*Initialize all the yummy delicious variables, they are so yummy and tasty! Gotta love em :D
* hoho
* hoohoh
* hohoho
* hehehe, love it
*/
bar = new Servo (7);
bar2= new Servo (8);
stick = new Joystick(1);
rightstick = new Joystick(2);
//belt= new Jaguar(5);
JagBelt= new RobotDrive(5,10);
//Drive = new RobotDrive(2,1);
myRobot = new RobotDrive(2,1);
cim1 = new Jaguar(3);
cim2= new Jaguar(6);
pickStop= new Jaguar(4);
spike = new Relay(1);
window= new Relay(2);
limitSwitch = new DigitalInput(1);
dash = DriverStation::GetInstance();
dsLCD = DriverStationLCD::GetInstance();
rangeFinder = new AnalogChannel(5);
gyro = new AnalogChannel(6);
Temperature = new AnalogChannel(7);
accelerometer = new ADXL345_I2C (1,ADXL345_I2C::kRange_2G);
//float Ri = (Vm/9.765625);
myRobot->SetExpiration(0.1);
}
// The initializer of dooooooom!!!!!
Robot() :
myRobot(0, 1), // these must be initialized in the same order
rStick(RIGHT_JOYSTICK_INPUT_CHANNEL), // as they are declared above.
lStick(LEFT_JOYSTICK_INPUT_CHANNEL),
gamePad(GAMEPAD_INPUT_CHANNEL),
lw(LiveWindow::GetInstance()),
autoLoopCounter(0),
gyro(GYRO_INPUT_CHANNEL),
encoder1(ENCODER_CHANNEL_1A, ENCODER_CHANNEL_1B),
encoder2(ENCODER_CHANNEL_2A, ENCODER_CHANNEL_2B),
lifterEncoder(LIFTER_ENCODER_CHANNEL_1, LIFTER_ENCODER_CHANNEL_2),
ballManipulatorEncoder(B_MANIPULATOR_ENCODER_CHANNEL_1, B_MANIPULATOR_ENCODER_CHANNEL_2),
lifter(LIFTER_CHANNEL_LIFT, LIFTER_CHANNEL_TILT, lifterEncoder),
ballManipulator(B_MANIPULATOR_CHANNEL_LIFT, B_MANIPULATOR_CHANNEL_PINCH, ballManipulatorEncoder)
{
myRobot.SetExpiration(0.1);
driveOption = TANK_GAMEPAD;
gyro.InitGyro();
showGyro = true;
showEncoderRaw = true;
showEncoderRate = false;
showEncoderIndex = false;
autoTurn = 0;
}
RobotDemo(void):
myRobot(1, 2), // these must be initialized in the same order
stick(1) // as they are declared above.
{
myRobot.SetExpiration(0.1);
kinect = Kinect::GetInstance();
//dash = SmartDashboard::GetInstance(); //Optional SmartDashboard logging
}
Robot() :
myRobot(0, 1), // these must be initialized in the same order
gPad(GAMEPAD_CHANNEL), // as they are declared above.
lw(LiveWindow::GetInstance()),
autoLoopCounter(0)
{
myRobot.SetExpiration(0.1);
}
Robot() :
myRobot(0, 1, 2, 3), //Remember to initialize things in the same order that they're declared
stick(0),
lw(LiveWindow::GetInstance()),
autoloopcounter(0)
{
myRobot.SetExpiration(0.1);
}
Robot() :
myRobot(0, 1), // these must be initialized in the same order
stick(0), // as they are declared above.
chooser()
{
//Note SmartDashboard is not initialized here, wait until RobotInit to make SmartDashboard calls
myRobot.SetExpiration(0.1);
}
Robot() :
robotDrive(new Talon(frontLeftChannel), new Talon(rearLeftChannel),
new Talon(frontRightChannel), new Talon(rearRightChannel)), stick(
STICK_CHANNEL), liftStick(LIFTSTICK_CHANNEL), chainLift(
CHAINLIFT_PWM), maxUp(MAXUP_DIO), maxDown(MAXDOWN_DIO), midPoint(
MIDPOINT_DIO), autoSwitch1(AUTOSWITCH1_DIO), autoSwitch2(
AUTOSWITCH2_DIO), leftIR(LEFTIR_LOC), rightIR(RIGHTIR_LOC), canGrabber(
CANGRAB_PWM) {
SmartDashboard::init();
ds = DriverStation::GetInstance();
SmartDashboard::PutString("STATUS:", "INITIALIZING");
robotDrive.SetExpiration(0.1);
robotDrive.SetInvertedMotor(RobotDrive::kFrontLeftMotor, true);
robotDrive.SetInvertedMotor(RobotDrive::kRearLeftMotor, true);
autoMode = new SendableChooser();
autoMode->AddDefault("00: Do Nothing", new AutonomousIndex(0));
autoMode->AddObject("01: Just Drive Forward", new AutonomousIndex(1));
autoMode->AddObject("02: Stack bin on tote, turn 90, go",
new AutonomousIndex(2));
autoMode->AddObject("03: Lift up and go forward",
new AutonomousIndex(3));
autoMode->AddObject("04: Lift up, turn 90, go", new AutonomousIndex(4));
autoMode->AddObject("05: Stack 3 bins w/ correction constant",
new AutonomousIndex(5));
autoMode->AddObject("06: Stack 3 bins w/ acclerometer",
new AutonomousIndex(6));
autoMode->AddObject("07: Grab first bin from landfill",
new AutonomousIndex(7));
autoMode->AddObject("08: Grab yellow bin and back up TO RAMP",
new AutonomousIndex(8));
autoMode->AddObject("09: Grab two bins from landfill, slide sideways",
new AutonomousIndex(9));
autoMode->AddObject("10: Grab from landfill, over by turning",
new AutonomousIndex(10));
autoMode->AddObject("11: Grab yellow bin, back up to AUTOZONE, drop",
new AutonomousIndex(11));
autoMode->AddObject("12: Grab yellow bin, back up to AUTOZONE, stop",
new AutonomousIndex(12));
autoMode->AddObject("13: Steal two green cans. Gottta go fast",
new AutonomousIndex(13));
autoMode->AddObject("99: CUPID SHUFFLE", new AutonomousIndex(99));
SmartDashboard::PutString("Both Off", "Pick from radio list");
SmartDashboard::PutString("On-Off", "Grab yellow and back up");
SmartDashboard::PutString("Off-On",
"Grab, turn right, drive, turn left");
SmartDashboard::PutString("Both On",
"Lift up, turn 90, drive to auto zone");
SmartDashboard::PutData("BOTH SWITCHES ON: Pick One:", autoMode);
SmartDashboard::PutData(Scheduler::GetInstance());
SmartDashboard::PutString("STATUS:", "READY");
SmartDashboard::PutBoolean("Smart Dashboard Enabled", false);
tick = 0;
leftIRZero = 0;
rightIRZero = 0;
}
Robot() :
myRobot(0, 1), // initialize robot to drive on ports 0 and 1
stick(0)
{
myRobot.SetExpiration(0.1);
camera.SetWhiteBalanceAuto(); //set the camera's white balance to auto
camera.SetExposureAuto(); //set the camera's exposure to auto
camera.UpdateSettings(); //make sure the camera's settings are up to date
}
Wheels()
{
drive = new RobotDrive(0,2,4,3); //frontLeft, rearLeft, frontRight, rearRight
drive->SetInvertedMotor(RobotDrive::kFrontLeftMotor, true); // 0 is front left wheel
drive->SetInvertedMotor(RobotDrive::kRearLeftMotor, true); // 2 is back left wheel
drive->SetExpiration(0.1);
drive->SetSafetyEnabled(true);
driveSafety = new MotorSafetyHelper(drive);
}
void TeleopInit() override {
drive->SetExpiration(200000);
drive->SetSafetyEnabled(false);
liftdown->Set(false);
intake_hold = false;
lastLiftPos = 0;
manual = true;
}
SixWheelBot(void):
//BUGBUG This probably won't work right now--don't run it
myRobot(1, 2, 3, 4), // these must be initialized in the same order
stickL(1), stickR(2) // as they are declared above.
{
myRobot.SetExpiration(0.1);
left = new DigitalInput(1);
middle = new DigitalInput(2);
right = new DigitalInput(3);
}
RobotDemo(void):
myRobot(1, 2), // these must be initialized in the same order
stick(1) // as they are declared above.
{
dsLCD = DriverStationLCD::GetInstance();
dsLCD->Clear();
dsLCD->PrintfLine(DriverStationLCD::kUser_Line1, "XboxController2");
dsLCD->UpdateLCD();
myRobot.SetExpiration(0.1);
}
/**
*
*
* Constructor for this robot subclass.
* Create an instance of a RobotDrive with left and right motors plugged into PWM
* ports 1 and 2 on the first digital module.
*/
DefaultRobot(void) {
ds = DriverStation::GetInstance();
myRobot = new RobotDrive(1, 3, 2, 4); // create robot drive base
rightStick = new Joystick(1); // create the joysticks
leftStick = new Joystick(2);
armStick = new Joystick(3);
armUpperLimit = new DigitalInput(1); // create the limit switch inputs
armLowerLimit = new DigitalInput(2);
//Update the motors at least every 100ms.
myRobot->SetExpiration(0.1);
}
RobotDemo(void):
myRobot(8, 1, 9, 2),
stick(1),
digEncoder(13, 14),
ultra(1, 1)
{
myRobot.SetExpiration(0.1);
myRobot.SetInvertedMotor(myRobot.kFrontRightMotor, true);
//myRobot.SetInvertedMotor(myRobot.kFrontLeftMotor, true);
myRobot.SetInvertedMotor(myRobot.kRearRightMotor, true);
//myRobot.SetInvertedMotor(myRobot.kRearLeftMotor, true);
}
Robot() :
myRobot(0, 1), // these must be initialized in the same order
driverStick(DRIVER_CONTROL_PORT), // as they are declared above.
operatorStick(OPERATOR_CONTROL_PORT),
leftDrive(LEFT_DRIVE_MOTOR_PWM),
rightDrive(RIGHT_DRIVE_MOTOR_PWM),
leftLift(LEFT_LIFT_MOTOR_PWM),
rightLift(RIGHT_LIFT_MOTOR_PWM),
leftIntake(LEFT_INTAKE_MOTOR_PWM),
rightIntake(RIGHT_INTAKE_MOTOR_PWM)
{
myRobot.SetExpiration(0.1);
}
//Class constructor
// Initialize the robot drive to:
// Drive base:
// Left Front Right
// +---------------------+
// | PWM 9 PWM 7|
// | Robot |
// | PWM 8 PWM 6|
// +---------------------+
// Back
Robot() :
robotDrive(9, 8, 7, 6), // these must be initialized in the same order
leftStick(0),
rightStick(1),// as they are declared above.
lw(NULL),
autoLoopCounter(0)
{
robotDrive.SetExpiration(0.1);
robotDrive.SetInvertedMotor(robotDrive.kFrontLeftMotor,false);
robotDrive.SetInvertedMotor(robotDrive.kFrontRightMotor,false);
robotDrive.SetInvertedMotor(robotDrive.kRearLeftMotor,false);
robotDrive.SetInvertedMotor(robotDrive.kRearRightMotor,false);
}
//Constructor (initialize variables)
Robot (void){
// Create a robot using standard right/left robot drive on PWMS 1, 2, 9, and 10
drivetrain = new RobotDrive(1, 2, 9, 10);
// overrides the default expiration time (0.5 seconds) and sets to 15 seconds, the length of autonomous
drivetrain->SetExpiration(15);
//Declare compressor
//(switch-GPIO, relay)
compressor=new Compressor(3,1);
// Acquire the Driver Station object
// GetInstance gets a pointer to a driver station object
m_ds = DriverStation::GetInstance();
// Define joystick USB ports on the Drivers Station
gamepad = new Joystick(1);
//Define encoder (channel A, channel B, true, k4X)
//true tells the encoder to not invert the counting direction
//right_encoder = new Encoder(1, 2, true);
//left_encoder = new Encoder(1, 2, true);
//Solenoids
drivetrain_pressure=new Solenoid(1);
drivetrain_vent=new Solenoid(8);
// Define global variables here
//DriveTrainValues
threshold=0.2;
right=0;
left=0;
oldright=0;
oldleft=0;
useright=0;
useleft=0;
leftchange=0;
rightchange=0;
leftdead=0.04; //was 0.02
rightdead=0.04; //was 0.02k
//Encoder
encoder_value =0;
}
Robot() :
frontLeftChannel(15),
frontRightChannel(11),
rearLeftChannel(12),
rearRightChannel(10),
robotDrive(frontLeftChannel, rearLeftChannel,
frontRightChannel, rearRightChannel), // these must be initialized in the same order
stick(joystickChannel) // as they are declared above.
{
robotDrive.SetExpiration(0.1);
robotDrive.SetInvertedMotor(RobotDrive::kFrontLeftMotor, true); // invert the motors
robotDrive.SetInvertedMotor(RobotDrive::kRearLeftMotor, true);
robotDrive.SetInvertedMotor(RobotDrive::kFrontRightMotor, true);
robotDrive.SetInvertedMotor(RobotDrive::kRearRightMotor, true); // you may need to change or remove this to match your robot
}
Robot() :
myRobot(0, 1), // initialize the RobotDrive to use motor controllers on ports 0 and 1
stick(0),
lw(LiveWindow::GetInstance()),
chooser(NULL),
autoSelected(),
imu(NULL),
m_rightBumper(false),
m_prevRightBumper(false),
m_leftBumper(false),
m_prevLeftBumper(false),
m_correcting1(false),
m_correcting2(false)
{
myRobot.SetExpiration(0.1);
}
Robot() :
robotDrive(Motor1, Motor2), // these must be initialized in the same order
stick(5), // as they are declared above.
lw(LiveWindow::GetInstance()),
autoLoopCounter(0),
Motor1(21),
Motor2(12),
Slave1(20),
Slave2(14),
t_motor(13),
arm_Motor(23),
finger_Motor(22),
intake_Spin_Motor(11),
intake_Winch_Motor(13),
stick2(4),
autoLoopCounter2(0)
{
robotDrive.SetExpiration(0.1);
robotDrive.SetSafetyEnabled(false);
Slave1.SetControlMode(CANSpeedController::kFollower);
Slave1.Set(21);
Slave2.SetControlMode(CANSpeedController::kFollower);
Slave2.Set(12);
Motor2.SetInverted(true); //12
Slave2.SetInverted(true);//14
arm_Motor.SetInverted(false);//23
t_motor.SetInverted(true);//23
// t_motor.SetControlMode(CANSpeedController::kVoltage);
// t_motor.Set(0);
// CameraServer::GetInstance()->SetQuality(50);
// CameraServer::GetInstance()->SetSize(2);
// //the camera name (ex "cam0") can be found through the roborio web interface
// CameraServer::GetInstance()->StartAutomaticCapture("cam0");
t_motor.SetControlMode(CANSpeedController::kPercentVbus);
// t_motor.SetVoltageCompensationRampRate(24.0);
t_motor.SetFeedbackDevice(CANTalon::QuadEncoder);
t_motor.SetPosition(0);
// t_motor.SetPID(1, 0, 0);
arm_Motor.SetControlMode(CANSpeedController::kPercentVbus);
finger_Motor.SetControlMode(CANSpeedController::kPercentVbus);
// ourRangefinder = new AnalogInput(0);
}
RobotDemo():
myRobot(1,2,3,4), //front left, rear left, front right, rear right (10,4,3,7) for whack (purple, yellow, green, red)
shoot(10),
stick(1), // usb number
shooter(6),
forklift(5),
winch(7),
shooterSole(2,3),//initialize festo valves
//forward channel, reverse channel
compressor(3, 3),
//(pressure switch channel, compressor relay channel) or
//(pressure switch module number, pressure switch channel, compressor relay module number, compressor relay channel)
shooterEnconder(5,6,false)//uint32_t aChannel, uint32_t bChannel, bool reverseDirection=false, EncodingType encodingType=k4X
{
myRobot.SetExpiration(0.1);
camera = AxisCamera::GetInstance();
}
