/*
* This function sends a single packet on the network and returns
* positive number (number of bytes transmitted) or negative for error
*/
static int davinci_eth_send_packet (struct eth_device *dev,
volatile void *packet, int length)
{
int ret_status = -1;
tx_send_loop = 0;
/* Return error if no link */
if (!phy.get_link_speed (active_phy_addr)) {
printf ("WARN: emac_send_packet: No link\n");
return (ret_status);
}
emac_gigabit_enable();
/* Check packet size and if < EMAC_MIN_ETHERNET_PKT_SIZE, pad it up */
if (length < EMAC_MIN_ETHERNET_PKT_SIZE) {
length = EMAC_MIN_ETHERNET_PKT_SIZE;
}
/* Populate the TX descriptor */
emac_tx_desc->next = 0;
emac_tx_desc->buffer = (u_int8_t *) packet;
emac_tx_desc->buff_off_len = (length & 0xffff);
emac_tx_desc->pkt_flag_len = ((length & 0xffff) |
EMAC_CPPI_SOP_BIT |
EMAC_CPPI_OWNERSHIP_BIT |
EMAC_CPPI_EOP_BIT);
/* Send the packet */
writel((unsigned long)emac_tx_desc, &adap_emac->TX0HDP);
/* Wait for packet to complete or link down */
while (1) {
if (!phy.get_link_speed (active_phy_addr)) {
davinci_eth_ch_teardown (EMAC_CH_TX);
return (ret_status);
}
emac_gigabit_enable();
if (readl(&adap_emac->TXINTSTATRAW) & 0x01) {
ret_status = length;
break;
}
tx_send_loop++;
}
return (ret_status);
}
/* Eth device open */
static int davinci_eth_open(struct eth_device *dev, bd_t *bis)
{
dv_reg_p addr;
u_int32_t clkdiv, cnt;
volatile emac_desc *rx_desc;
u_int16_t lpa_val;
debug_emac("+ emac_open\n");
/* Reset EMAC module and disable interrupts in wrapper */
adap_emac->SOFTRESET = 1;
while (adap_emac->SOFTRESET != 0) {;}
#if (defined(CONFIG_SOC_DM646x) || defined(CONFIG_SOC_DM365) || \
defined(CONFIG_OMAP3_AM3517EVM) || defined(CONFIG_OMAP3_AM3517CRANE))
adap_ewrap->SOFTRST = 1;
while (adap_ewrap->SOFTRST != 0) {;}
#else
adap_ewrap->EWCTL = 0;
for (cnt = 0; cnt < 5; cnt++) {
clkdiv = adap_ewrap->EWCTL;
}
#endif
rx_desc = emac_rx_desc;
adap_emac->TXCONTROL = 0x01;
adap_emac->RXCONTROL = 0x01;
/* Set MAC Addresses & Init multicast Hash to 0 (disable any multicast receive) */
/* Using channel 0 only - other channels are disabled */
adap_emac->MACINDEX = 0;
adap_emac->MACADDRHI =
(davinci_eth_mac_addr[3] << 24) |
(davinci_eth_mac_addr[2] << 16) |
(davinci_eth_mac_addr[1] << 8) |
(davinci_eth_mac_addr[0]);
#if (defined(CONFIG_SOC_DM646x) || defined(CONFIG_SOC_DM365) || \
defined(CONFIG_OMAP3_AM3517EVM) || defined(CONFIG_OMAP3_AM3517CRANE))
adap_emac->MACADDRLO =
(davinci_eth_mac_addr[5] << 8) |
(davinci_eth_mac_addr[4]| (1 << 19) | (1 << 20));
#else
adap_emac->MACADDRLO =
(davinci_eth_mac_addr[5] << 8) |
(davinci_eth_mac_addr[4]);
#endif
adap_emac->MACHASH1 = 0;
adap_emac->MACHASH2 = 0;
/* Set source MAC address - REQUIRED */
adap_emac->MACSRCADDRHI =
(davinci_eth_mac_addr[3] << 24) |
(davinci_eth_mac_addr[2] << 16) |
(davinci_eth_mac_addr[1] << 8) |
(davinci_eth_mac_addr[0]);
adap_emac->MACSRCADDRLO =
(davinci_eth_mac_addr[4] << 8) |
(davinci_eth_mac_addr[5]);
/* Set DMA 8 TX / 8 RX Head pointers to 0 */
addr = &adap_emac->TX0HDP;
for(cnt = 0; cnt < 16; cnt++)
*addr++ = 0;
addr = &adap_emac->RX0HDP;
for(cnt = 0; cnt < 16; cnt++)
*addr++ = 0;
/* Clear Statistics (do this before setting MacControl register) */
addr = &adap_emac->RXGOODFRAMES;
for(cnt = 0; cnt < EMAC_NUM_STATS; cnt++)
*addr++ = 0;
/* No multicast addressing */
adap_emac->MACHASH1 = 0;
adap_emac->MACHASH2 = 0;
/* Create RX queue and set receive process in place */
emac_rx_active_head = emac_rx_desc;
for (cnt = 0; cnt < EMAC_MAX_RX_BUFFERS; cnt++) {
rx_desc->next = BD_TO_HW((u_int32_t)(rx_desc + 1));
rx_desc->buffer = &emac_rx_buffers[cnt * (EMAC_MAX_ETHERNET_PKT_SIZE + EMAC_PKT_ALIGN)];
rx_desc->buff_off_len = EMAC_MAX_ETHERNET_PKT_SIZE;
rx_desc->pkt_flag_len = EMAC_CPPI_OWNERSHIP_BIT;
rx_desc++;
}
/* Set the last descriptor's "next" parameter to 0 to end the RX desc list */
rx_desc--;
rx_desc->next = 0;
emac_rx_active_tail = rx_desc;
emac_rx_queue_active = 1;
/* Enable TX/RX */
adap_emac->RXMAXLEN = EMAC_MAX_ETHERNET_PKT_SIZE;
adap_emac->RXBUFFEROFFSET = 0;
/* No fancy configs - Use this for promiscous for debug - EMAC_RXMBPENABLE_RXCAFEN_ENABLE */
adap_emac->RXMBPENABLE = EMAC_RXMBPENABLE_RXBROADEN;
/* Enable ch 0 only */
adap_emac->RXUNICASTSET = 0x01;
/* Init MDIO & get link state */
clkdiv = (EMAC_MDIO_BUS_FREQ / EMAC_MDIO_CLOCK_FREQ) - 1;
adap_mdio->CONTROL = ((clkdiv & 0xff) | MDIO_CONTROL_ENABLE | MDIO_CONTROL_FAULT);
if (!phy.auto_negotiate(active_phy_addr))
return(0);
davinci_eth_phy_read(active_phy_addr,PHY_ANLPAR,&lpa_val);
if (lpa_val & (PHY_ANLPAR_10FD | PHY_ANLPAR_TXFD) ) {
/* set EMAC for Full Duplex */
adap_emac->MACCONTROL = EMAC_MACCONTROL_MIIEN_ENABLE |
EMAC_MACCONTROL_FULLDUPLEX_ENABLE;
}else{
/*set EMAC for Half Duplex */
adap_emac->MACCONTROL = EMAC_MACCONTROL_MIIEN_ENABLE;
}
#ifdef CONFIG_DRIVER_TI_EMAC_USE_RMII
if (lpa_val & (PHY_ANLPAR_TXFD | PHY_ANLPAR_TX) ) {
adap_emac->MACCONTROL |= EMAC_MACCONTROL_RMIISPEED_100;
} else {
adap_emac->MACCONTROL &= ~EMAC_MACCONTROL_RMIISPEED_100;
}
#endif
/* Start receive process */
adap_emac->RX0HDP = BD_TO_HW((u_int32_t)emac_rx_desc);
debug_emac("- emac_open\n");
return(1);
}
/* Eth device open */
static int davinci_eth_open(struct eth_device *dev, bd_t *bis)
{
dv_reg_p addr;
u_int32_t clkdiv, cnt;
volatile emac_desc *rx_desc;
debug_emac("+ emac_open\n");
/* Reset EMAC module and disable interrupts in wrapper */
writel(1, &adap_emac->SOFTRESET);
while (readl(&adap_emac->SOFTRESET) != 0)
;
#if defined(DAVINCI_EMAC_VERSION2)
writel(1, &adap_ewrap->softrst);
while (readl(&adap_ewrap->softrst) != 0)
;
#else
writel(0, &adap_ewrap->EWCTL);
for (cnt = 0; cnt < 5; cnt++) {
clkdiv = readl(&adap_ewrap->EWCTL);
}
#endif
#if defined(CONFIG_DRIVER_TI_EMAC_USE_RMII) && \
defined(CONFIG_MACH_DAVINCI_DA850_EVM)
adap_ewrap->c0rxen = adap_ewrap->c1rxen = adap_ewrap->c2rxen = 0;
adap_ewrap->c0txen = adap_ewrap->c1txen = adap_ewrap->c2txen = 0;
adap_ewrap->c0miscen = adap_ewrap->c1miscen = adap_ewrap->c2miscen = 0;
#endif
rx_desc = emac_rx_desc;
writel(1, &adap_emac->TXCONTROL);
writel(1, &adap_emac->RXCONTROL);
davinci_eth_set_mac_addr(dev);
/* Set DMA 8 TX / 8 RX Head pointers to 0 */
addr = &adap_emac->TX0HDP;
for(cnt = 0; cnt < 16; cnt++)
writel(0, addr++);
addr = &adap_emac->RX0HDP;
for(cnt = 0; cnt < 16; cnt++)
writel(0, addr++);
/* Clear Statistics (do this before setting MacControl register) */
addr = &adap_emac->RXGOODFRAMES;
for(cnt = 0; cnt < EMAC_NUM_STATS; cnt++)
writel(0, addr++);
/* No multicast addressing */
writel(0, &adap_emac->MACHASH1);
writel(0, &adap_emac->MACHASH2);
/* Create RX queue and set receive process in place */
emac_rx_active_head = emac_rx_desc;
for (cnt = 0; cnt < EMAC_MAX_RX_BUFFERS; cnt++) {
rx_desc->next = (u_int32_t)(rx_desc + 1);
rx_desc->buffer = &emac_rx_buffers[cnt * (EMAC_MAX_ETHERNET_PKT_SIZE + EMAC_PKT_ALIGN)];
rx_desc->buff_off_len = EMAC_MAX_ETHERNET_PKT_SIZE;
rx_desc->pkt_flag_len = EMAC_CPPI_OWNERSHIP_BIT;
rx_desc++;
}
/* Finalize the rx desc list */
rx_desc--;
rx_desc->next = 0;
emac_rx_active_tail = rx_desc;
emac_rx_queue_active = 1;
/* Enable TX/RX */
writel(EMAC_MAX_ETHERNET_PKT_SIZE, &adap_emac->RXMAXLEN);
writel(0, &adap_emac->RXBUFFEROFFSET);
/*
* No fancy configs - Use this for promiscous debug
* - EMAC_RXMBPENABLE_RXCAFEN_ENABLE
*/
writel(EMAC_RXMBPENABLE_RXBROADEN, &adap_emac->RXMBPENABLE);
/* Enable ch 0 only */
writel(1, &adap_emac->RXUNICASTSET);
/* Enable MII interface and Full duplex mode */
#ifdef CONFIG_SOC_DA8XX
writel((EMAC_MACCONTROL_MIIEN_ENABLE |
EMAC_MACCONTROL_FULLDUPLEX_ENABLE |
EMAC_MACCONTROL_RMIISPEED_100),
&adap_emac->MACCONTROL);
#else
writel((EMAC_MACCONTROL_MIIEN_ENABLE |
EMAC_MACCONTROL_FULLDUPLEX_ENABLE),
&adap_emac->MACCONTROL);
#endif
/* Init MDIO & get link state */
clkdiv = (EMAC_MDIO_BUS_FREQ / EMAC_MDIO_CLOCK_FREQ) - 1;
writel((clkdiv & 0xff) | MDIO_CONTROL_ENABLE | MDIO_CONTROL_FAULT,
&adap_mdio->CONTROL);
/* We need to wait for MDIO to start */
udelay(1000);
if (!phy.get_link_speed(active_phy_addr))
return(0);
emac_gigabit_enable();
/* Start receive process */
writel((u_int32_t)emac_rx_desc, &adap_emac->RX0HDP);
debug_emac("- emac_open\n");
return(1);
}
/* Eth device open */
static int dm644x_eth_open(void)
{
dv_reg_p addr;
u_int32_t clkdiv, cnt;
volatile emac_desc *rx_desc;
debug_emac("+ emac_open\n");
/* Reset EMAC module and disable interrupts in wrapper */
adap_emac->SOFTRESET = 1;
while (adap_emac->SOFTRESET != 0) {;}
adap_ewrap->EWCTL = 0;
for (cnt = 0; cnt < 5; cnt++) {
clkdiv = adap_ewrap->EWCTL;
}
rx_desc = emac_rx_desc;
adap_emac->TXCONTROL = 0x01;
adap_emac->RXCONTROL = 0x01;
/* Set MAC Addresses & Init multicast Hash to 0 (disable any multicast receive) */
/* Using channel 0 only - other channels are disabled */
adap_emac->MACINDEX = 0;
adap_emac->MACADDRHI =
(dm644x_eth_mac_addr[3] << 24) |
(dm644x_eth_mac_addr[2] << 16) |
(dm644x_eth_mac_addr[1] << 8) |
(dm644x_eth_mac_addr[0]);
adap_emac->MACADDRLO =
(dm644x_eth_mac_addr[5] << 8) |
(dm644x_eth_mac_addr[4]);
adap_emac->MACHASH1 = 0;
adap_emac->MACHASH2 = 0;
/* Set source MAC address - REQUIRED */
adap_emac->MACSRCADDRHI =
(dm644x_eth_mac_addr[3] << 24) |
(dm644x_eth_mac_addr[2] << 16) |
(dm644x_eth_mac_addr[1] << 8) |
(dm644x_eth_mac_addr[0]);
adap_emac->MACSRCADDRLO =
(dm644x_eth_mac_addr[4] << 8) |
(dm644x_eth_mac_addr[5]);
/* Set DMA 8 TX / 8 RX Head pointers to 0 */
addr = &adap_emac->TX0HDP;
for(cnt = 0; cnt < 16; cnt++)
*addr++ = 0;
addr = &adap_emac->RX0HDP;
for(cnt = 0; cnt < 16; cnt++)
*addr++ = 0;
/* Clear Statistics (do this before setting MacControl register) */
addr = &adap_emac->RXGOODFRAMES;
for(cnt = 0; cnt < EMAC_NUM_STATS; cnt++)
*addr++ = 0;
/* No multicast addressing */
adap_emac->MACHASH1 = 0;
adap_emac->MACHASH2 = 0;
/* Create RX queue and set receive process in place */
emac_rx_active_head = emac_rx_desc;
for (cnt = 0; cnt < EMAC_MAX_RX_BUFFERS; cnt++) {
rx_desc->next = (u_int32_t)(rx_desc + 1);
rx_desc->buffer = &emac_rx_buffers[cnt * (EMAC_MAX_ETHERNET_PKT_SIZE + EMAC_PKT_ALIGN)];
rx_desc->buff_off_len = EMAC_MAX_ETHERNET_PKT_SIZE;
rx_desc->pkt_flag_len = EMAC_CPPI_OWNERSHIP_BIT;
rx_desc++;
}
/* Set the last descriptor's "next" parameter to 0 to end the RX desc list */
rx_desc--;
rx_desc->next = 0;
emac_rx_active_tail = rx_desc;
emac_rx_queue_active = 1;
/* Enable TX/RX */
adap_emac->RXMAXLEN = EMAC_MAX_ETHERNET_PKT_SIZE;
adap_emac->RXBUFFEROFFSET = 0;
/* No fancy configs - Use this for promiscous for debug - EMAC_RXMBPENABLE_RXCAFEN_ENABLE */
adap_emac->RXMBPENABLE = EMAC_RXMBPENABLE_RXBROADEN;
/* Enable ch 0 only */
adap_emac->RXUNICASTSET = 0x01;
/* Enable MII interface and Full duplex mode */
adap_emac->MACCONTROL = (EMAC_MACCONTROL_MIIEN_ENABLE | EMAC_MACCONTROL_FULLDUPLEX_ENABLE);
/* Init MDIO & get link state */
clkdiv = (EMAC_MDIO_BUS_FREQ / EMAC_MDIO_CLOCK_FREQ) - 1;
adap_mdio->CONTROL = ((clkdiv & 0xff) | MDIO_CONTROL_ENABLE | MDIO_CONTROL_FAULT);
if (!phy.get_link_speed(active_phy_addr))
return(0);
/* Start receive process */
adap_emac->RX0HDP = (u_int32_t)emac_rx_desc;
debug_emac("- emac_open\n");
return(1);
}
