u16 adc_measure(void){
u8 channel_array[16];
u16 val,valLoaded;
/* Select the channel we want to convert. 16=temperature_sensor. */
channel_array[0] = 6;
adc_set_regular_sequence(ADC1, 1, channel_array);
/*
* Start the conversion directly (not trigger mode).
*/
adc_start_conversion_direct(ADC1);
/* Wait for end of conversion. */
while (!(ADC_SR(ADC1) & ADC_SR_EOC));
val = ADC_DR(ADC1);
return val;
gpio_set(GPIOA, GPIO1);
adc_start_conversion_direct(ADC1);
/* Wait for end of conversion. */
while (!(ADC_SR(ADC1) & ADC_SR_EOC));
valLoaded = ADC_DR(ADC1);
gpio_clear(GPIOA, GPIO5 | GPIO1);
return val - valLoaded;
}
void init_adc_sensor(){
// we will use ADC1 channel 0 for IR sensor & ADC1 channel 1 for laser's photoresistor
uint8_t adc_channel_array[ADC_CHANNEL_NUMBER] = {0,1,6};
// Make sure the ADC doesn't run during config
adc_off(ADC1);
// enable ADC & PA0/PA1 clocking
rcc_peripheral_enable_clock(&RCC_APB2ENR, RCC_APB2ENR_ADC1EN | RCC_APB2ENR_IOPAEN);
rcc_set_adcpre(RCC_CFGR_ADCPRE_PCLK2_DIV4);
gpio_set_mode(GPIOA, GPIO_MODE_INPUT, GPIO_CNF_INPUT_ANALOG, GPIO0 | GPIO1);
rcc_periph_clock_enable(RCC_DMA1); // enable DMA for ADC values storing
// Configure ADC as continuous scan mode with DMA
ADC1_CR1 = ADC_CR1_SCAN; // enable scan mode
// set sample time on channels 1&2: 239.5 cycles for better results
ADC1_SMPR2 = 0x3f;
dma_channel_reset(DMA1, DMA_CHANNEL1);
DMA1_CPAR1 = (uint32_t) &(ADC_DR(ADC1));
DMA1_CMAR1 = (uint32_t) ADC_value;
DMA1_CNDTR1 = ADC_CHANNEL_NUMBER;
DMA1_CCR1 = DMA_CCR_MINC | DMA_CCR_PSIZE_16BIT | DMA_CCR_MSIZE_16BIT
| DMA_CCR_CIRC | DMA_CCR_PL_HIGH | DMA_CCR_EN;
// continuous conv, enable ADC & DMA
ADC1_CR2 = ADC_CR2_CONT | ADC_CR2_ADON | ADC_CR2_DMA;
// set channels
adc_set_regular_sequence(ADC1, ADC_CHANNEL_NUMBER, adc_channel_array);
// reset calibration registers & start calibration
ADC1_CR2 |= ADC_CR2_RSTCAL;
while(ADC1_CR2 & ADC_CR2_RSTCAL); // wait for registers reset
ADC1_CR2 |= ADC_CR2_CAL;
while(ADC1_CR2 & ADC_CR2_CAL); // wait for calibration ends
nvic_enable_irq(NVIC_ADC1_2_IRQ);
ADC1_CR2 |= ADC_CR2_SWSTART;
// turn on ADC - to do it we need set ADC_CR2_ADON again!
ADC1_CR2 |= ADC_CR2_ADON;
}
static uint16_t ADC_Measure(uint16_t ch)
{
uint16_t val;
uint8_t channel_array[16];
/* Make sure the ADC doesn't run during config. */
// adc_off(TS_ADC);
/* We configure everything for one single conversion. */
adc_disable_scan_mode(TS_ADC);
adc_set_single_conversion_mode(TS_ADC);
adc_disable_external_trigger_regular(TS_ADC);
adc_set_right_aligned(TS_ADC);
/* ADC regular channel14 configuration */
// adc_set_sample_time(TS_ADC, ch, ADC_SMPR_SMP_55DOT5CYC);
adc_set_sample_time_on_all_channels(TS_ADC, ADC_SMPR_SMP_55DOT5CYC);
// adc_set_sample_time_on_all_channels(ADC1, ADC_SMPR_SMP_28DOT5CYC);
// ADC_RegularChannelConfig(TS_ADC, ch, 1, ADC_SampleTime_55Cycles5);
/* Enable ADC */
// ADC_Cmd(TS_ADC, ENABLE);
adc_power_on(TS_ADC);
delay(100);
#if 1
/* Enable ADC reset calibaration register */
adc_reset_calibration(TS_ADC);
// ADC_ResetCalibration(TS_ADC);
/* Check the end of ADC reset calibration register */
// while(ADC_GetResetCalibrationStatus(TS_ADC));
/* Start ADC calibaration */
// ADC_StartCalibration(TS_ADC);
// adc_calibration(TS_ADC);
adc_calibrate_async(TS_ADC);
/* Check the end of ADC calibration */
// while(ADC_GetCalibrationStatus(TS_ADC));
#endif
/* Select the channel we want to convert. */
channel_array[0] = ch;
adc_set_regular_sequence(TS_ADC, 1, channel_array);
/* Start ADC Software Conversion */
// adc_start_conversion_regular(TS_ADC);
adc_start_conversion_direct(TS_ADC);
while(!adc_eoc(TS_ADC));
// val = adc_read_regular(TS_ADC);
val = ADC_DR(TS_ADC);
// adc_off(TS_ADC);
return val;
}
batt_state adc_testBatt(void){
u8 channel_array[16];
u16 val,valLoaded;
gpio_set(GPIOA, GPIO5);
delay_ms(25);
/* Select the channel we want to convert. 16=temperature_sensor. */
channel_array[0] = 6;
adc_set_regular_sequence(ADC1, 1, channel_array);
/*
* Start the conversion directly (not trigger mode).
*/
adc_start_conversion_direct(ADC1);
/* Wait for end of conversion. */
while (!(ADC_SR(ADC1) & ADC_SR_EOC));
val = ADC_DR(ADC1);
if(val < 0x0A3D){
return BATTCRIT;
}
val = val & 0xFFFC;
gpio_set(GPIOA, GPIO1);
delay_ms(25);
adc_start_conversion_direct(ADC1);
/* Wait for end of conversion. */
while (!(ADC_SR(ADC1) & ADC_SR_EOC));
valLoaded = ADC_DR(ADC1);
gpio_clear(GPIOA, GPIO5 | GPIO1);
valLoaded = valLoaded & 0xFFFC;
// kontroluje pokles vetsi nez 0,75 V po zatizeni 15 Ohm
if(val - valLoaded > 0x1E0){
return BATTLOW;
}
return BATTOK;
}
uint16_t adc_read(uint8_t ch)
{
while (!(ADC_SR(ADC1) & ADC_SR_EOC));
uint16_t last_res = ADC_DR(ADC1);
/* Select the channel we want to convert. 16=temperature_sensor. */
uint8_t channel_array[16];
channel_array[0] = ch;
adc_set_regular_sequence(ADC1, 1, channel_array);
/* Start the conversion directly (not trigger mode). */
adc_start_conversion_direct(ADC1);
return last_res;
}
int main(void)
{
u8 channel_array[16];
u16 temperature;
rcc_clock_setup_in_hse_16mhz_out_72mhz();
gpio_setup();
usart_setup();
adc_setup();
gpio_clear(GPIOB, GPIO7); /* LED1 on */
gpio_set(GPIOB, GPIO6); /* LED2 off */
/* Send a message on USART1. */
usart_send(USART1, 's');
usart_send(USART1, 't');
usart_send(USART1, 'm');
usart_send(USART1, '\r');
usart_send(USART1, '\n');
/* Select the channel we want to convert. 16=temperature_sensor. */
channel_array[0] = 16;
adc_set_regular_sequence(ADC1, 1, channel_array);
/*
* If the ADC_CR2_ON bit is already set -> setting it another time
* starts the conversion.
*/
adc_on(ADC1);
/* Wait for end of conversion. */
while (!(ADC_SR(ADC1) & ADC_SR_EOC));
temperature = ADC_DR(ADC1);
/*
* That's actually not the real temperature - you have to compute it
* as described in the datasheet.
*/
my_usart_print_int(USART1, temperature);
gpio_clear(GPIOB, GPIO6); /* LED2 on */
while(1); /* Halt. */
return 0;
}
int main(void)
{
uint8_t channel_array[16];
uint16_t temperature;
rcc_clock_setup_in_hse_16mhz_out_72mhz();
gpio_setup();
usart_setup();
adc_setup();
gpio_clear(GPIOB, GPIO7); /* LED1 on */
gpio_set(GPIOB, GPIO6); /* LED2 off */
/* Send a message on USART1. */
usart_send(USART1, 's');
usart_send(USART1, 't');
usart_send(USART1, 'm');
usart_send(USART1, '\r');
usart_send(USART1, '\n');
/* Select the channel we want to convert. 16=temperature_sensor. */
channel_array[0] = 16;
adc_set_regular_sequence(ADC1, 1, channel_array);
/*
* Start the conversion directly (not trigger mode).
*/
adc_start_conversion_direct(ADC1);
/* Wait for end of conversion. */
while (!(ADC_SR(ADC1) & ADC_SR_EOC));
temperature = ADC_DR(ADC1);
/*
* That's actually not the real temperature - you have to compute it
* as described in the datasheet.
*/
my_usart_print_int(USART1, temperature);
gpio_clear(GPIOB, GPIO6); /* LED2 on */
while(1); /* Halt. */
return 0;
}
uint32_t adc_read_regular(uint32_t adc)
{
return ADC_DR(adc);
}
