/* change the bit timings of the selected CAN channel */
int CAN_SetTiming (int board, int baud)
{
/* int custom=0; */
BTR_TAB_TOUCAN_T * table = (BTR_TAB_TOUCAN_T*)can_btr_tab_toucan;
DBGin("CAN_SetTiming");
DBGprint(DBG_DATA, ("baud[%d]=%d", board, baud));
/* enable changing of bit timings */
CANsetw(board, canmcr, CAN_MCR_HALT);
/* search for data from table */
while(1) {
if (table->rate == 0 || table->rate == baud) {
break;
}
table++;
}
if (table->rate == 0) {
/* try to use baud as custom specific bit rate
* not implemented yet
*/
return -ENXIO;
}
/*
* Set Timing Register values.
* Initialize the bit timing parameters PROPSEG, PSEG1, PSEG2 and RJW
* in control registers 1 and 2.
*
* The FlexCAN module uses three 8-bit registers to set-up
* the bit timing parameters required by the CAN protocol.
* Control registers 1 and 2 contain the PROPSEG, PSEG1, PSEG2
* and RJW fields which allow the user to configure
* the bit timing parameters.
* The prescaler divide register (PRESDIV) allows the user to select
* the ratio used to derive the S-Clock from the system clock.
* The time quanta clock operates at the S-clock frequency.
*/
CANout(board, presdiv, table->presdiv);
CANout(board, canctrl2, ((table->pseg1 << 3)+ table->pseg2));
CANout(board, canctrl1, (
0 /* SAMP = 0 , 0/0x80 */
+ 0 /* LOOP = 0 , 0/0x40 */
+ 0 /* TSYNC= 0 , 0/0x20 */
+ 0 /* LBUF = 0 , 0/0x10 */
+ 0 /* RSVD = 0 , 0/0x08 */
+ table->propseg)
);
/*
* Stay in configuration mode; a call to Start-CAN() is necessary to
* activate the CAN controller with the new bit rate
*/
DBGprint(DBG_DATA,("canctrl2=0x%x presdiv=0x%x",
CANin(board, canctrl2), CANin(board, presdiv)) );
DBGout();
return 0;
}
int can_GetStat(
struct inode *inode,
CanStatusPar_t *stat
)
{
unsigned int board = MINOR(inode->i_rdev);
msg_fifo_t *Fifo;
unsigned long flags;
stat->type = CAN_TYPE_FlexCAN;
stat->baud = Baud[board];
/* printk(" STAT ST 0x%x\n", CANin(board, canstat)); */
stat->status = CANinw(board, estat);
/* not available in the FlexCAN, lets fill 127 here */
stat->error_warning_limit = 127;
stat->rx_errors = CANin(board, rxectr);
stat->tx_errors = CANin(board, txectr);
/* error code is not available, use estat again */
stat->error_code= CANinw(board, estat);
/* Collect information about the RX and TX buffer usage */
/* Disable CAN Interrupts */
/* !!!!!!!!!!!!!!!!!!!!! */
save_flags(flags); cli();
Fifo = &Rx_Buf[board];
stat->rx_buffer_size = MAX_BUFSIZE; /**< size of rx buffer */
/* number of messages */
stat->rx_buffer_used =
(Fifo->head < Fifo->tail)
? (MAX_BUFSIZE - Fifo->tail + Fifo->head) : (Fifo->head - Fifo->tail);
Fifo = &Tx_Buf[board];
stat->tx_buffer_size = MAX_BUFSIZE; /* size of tx buffer */
/* number of messages */
stat->tx_buffer_used =
(Fifo->head < Fifo->tail)
? (MAX_BUFSIZE - Fifo->tail + Fifo->head) : (Fifo->head - Fifo->tail);
/* Enable CAN Interrupts */
/* !!!!!!!!!!!!!!!!!!!!! */
restore_flags(flags);
return 0;
}
//reset the CAN device
void reset_ADV_PCI(int dev)
{
unsigned char temp;
#ifdef CAN_DEBUG
printk("Enter can_reset, device = %d\n", dev);
#endif
if (dev < 0 || dev>= MAX_CHANNELS )
{
#ifdef CAN_DEBUG
printk( "in can_get_reg function the device=%d is error!\n", dev);
#endif
return;
}
temp = CANin(dev, canmode );
CANout(dev, canmode, temp|0x01 );
udelay(10000);
}
