/******************************************************************************
* Outline : PowerON_Reset_PC
* Description : This program is the MCU's entry point from a power-on reset.
* The function configures the MCU stack, then calls the
* HardwareSetup function and main function sequentially.
* Argument : none
* Return value : none
******************************************************************************/
void PowerON_Reset_PC(void)
{
/* Initialise the MCU processor word */
#if __RENESAS_VERSION__ >= 0x01010000
set_intb((void *)__sectop("C$VECT"));
#else
set_intb((unsigned long)__sectop("C$VECT"));
#endif
set_fpsw(FPSW_init);
/* Initialise the MCU stack area */
_INITSCT();
/* Configure the MCU and YRDK hardware */
HardwareSetup();
/* Change the MCU's usermode from supervisor to user */
nop();
set_psw(PSW_init);
Change_PSW_PM_to_UserMode();
/* Call the main program function */
main();
/* Invoke a break interrupt */
brk();
}
//#pragma section P UserAppStartSect // Output PowerON_Reset to PResetPRG section
void UserAppStart(void)
#endif
{
/* Stack pointers are setup prior to calling this function - see comments above */
/* Initialise the MCU processor word */
#if __RENESAS_VERSION__ >= 0x01010000
set_intb((void *)__sectop("C$VECT"));
#else
set_intb((unsigned long)__sectop("C$VECT"));
#endif
#if (BSP_CFG_USE_CGC_MODULE == 0)
/* Switch to high-speed operation */
operating_frequency_set();
#else
cgc_clock_config();
#endif
/* If the warm start Pre C runtime callback is enabled, then call it. */
#if BSP_CFG_USER_WARM_START_CALLBACK_PRE_INITC_ENABLED == 1
BSP_CFG_USER_WARM_START_PRE_C_FUNCTION();
#endif
/* Initialize C runtime environment */
_INITSCT();
/* If the warm start Post C runtime callback is enabled, then call it. */
#if BSP_CFG_USER_WARM_START_CALLBACK_POST_INITC_ENABLED == 1
BSP_CFG_USER_WARM_START_POST_C_FUNCTION();
#endif
#if BSP_CFG_IO_LIB_ENABLE == 1
/* Comment this out if not using I/O lib */
_INIT_IOLIB();
#endif
/* Initialize MCU interrupt callbacks. */
bsp_interrupt_open();
/* Initialize register protection functionality. */
bsp_register_protect_open();
/* Configure the MCU and board hardware */
hardware_setup();
/* Change the MCU's user mode from supervisor to user */
nop();
set_psw(PSW_init);
#if BSP_CFG_RUN_IN_USER_MODE==1
/* Use chg_pmusr() intrinsic if possible. */
#if __RENESAS_VERSION__ >= 0x01010000
chg_pmusr() ;
#else
Change_PSW_PM_to_UserMode();
#endif
#endif
/* Enable the bus error interrupt to catch accesses to illegal/reserved areas of memory */
R_BSP_InterruptControl(BSP_INT_SRC_BUS_ERROR, BSP_INT_CMD_INTERRUPT_ENABLE, FIT_NO_PTR);
/* Call the main program function (should not return) */
main();
#if BSP_CFG_IO_LIB_ENABLE == 1
/* Comment this out if not using I/O lib - cleans up open files */
_CLOSEALL();
#endif
/* BCH - 01/16/2013 */
/* Infinite loop is intended here. */
while(1) /* PRQA S 2740 */
{
/* Infinite loop. Put a breakpoint here if you want to catch an exit of main(). */
}
}
