/**
* XhciInitIndirectReg - Config XHCI Indirect Registers
*
*
*
* @param[in] FchDataPtr Fch configuration structure pointer.
*
*/
VOID
XhciInitIndirectReg (
IN FCH_DATA_BLOCK *FchDataPtr
)
{
FchXhciInitIndirectReg (FchDataPtr);
}
/**
* XhciInitIndirectReg - Config XHCI Indirect Registers
*
*
*
* @param[in] StdHeader AMD Standard Header
*
*/
VOID
XhciInitIndirectReg (
IN AMD_CONFIG_PARAMS *StdHeader
)
{
FchXhciInitIndirectReg (StdHeader);
}
/**
* FchXhciInitBeforePciInit - Config XHCI controller before PCI
* emulation
*
*
*
* @param[in] FchDataPtr Fch configuration structure pointer.
*
*/
VOID
FchXhciInitBeforePciInit (
IN FCH_DATA_BLOCK *FchDataPtr
)
{
UINT16 BcdAddress;
UINT16 BcdSize;
UINT16 AcdAddress;
UINT16 AcdSize;
UINT16 FwAddress;
UINT16 FwSize;
UINT32 XhciFwStarting;
UINT32 SpiValidBase;
UINT32 RegData;
UINT16 Index;
BOOLEAN Xhci0Enable;
BOOLEAN Xhci1Enable;
FCH_DATA_BLOCK *LocalCfgPtr;
AMD_CONFIG_PARAMS *StdHeader;
LocalCfgPtr = (FCH_DATA_BLOCK *)FchDataPtr;
StdHeader = LocalCfgPtr->StdHeader;
Xhci0Enable = LocalCfgPtr->Usb.Xhci0Enable;
Xhci1Enable = LocalCfgPtr->Usb.Xhci1Enable;
if (( Xhci0Enable == 0 ) && (Xhci1Enable == 0)) {
return;
}
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG00, AccessWidth32, 0x00000000, 0x00400700);
FchStall (20, StdHeader);
XhciFwStarting = FchCombineSigRomInfo (FchDataPtr);
if ( XhciFwStarting == 0 ) {
return;
}
//
// Enable SuperSpeed receive special error case logic. 0x20 bit8
// Enable USB2.0 RX_Valid Synchronization. 0x20 bit9
// Enable USB2.0 DIN/SE0 Synchronization. 0x20 bit10
//
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG20, AccessWidth32, 0xFFFFF8FF, 0x00000700);
//
// SuperSpeed PHY Configuration (adaptation timer setting)
// XHC U1 LFPS Exit time
//
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG90, AccessWidth32, 0xCFF00000, 0x000AAAAA);
//RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG90 + 0x40, AccessWidth32, 0xFFF00000, 0x000AAAAA);
//
// Step 1. to enable Xhci IO and Firmware load mode
//
RwMem (ACPI_MMIO_BASE + PMIO_BASE + FCH_PMIOA_REGEF, AccessWidth8, ~(UINT32) (BIT4 + BIT5), 0); /// Disable Device 22
RwMem (ACPI_MMIO_BASE + PMIO_BASE + FCH_PMIOA_REGEF, AccessWidth8, ~(UINT32) (BIT7), BIT7); /// Enable 2.0 devices
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG00, AccessWidth32, 0xF0FFFFFC, (Xhci0Enable + (Xhci1Enable << 1)) & 0x03);
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG00, AccessWidth32, 0xEFFFFFFF, 0x10000000);
//
// Step 2. to read a portion of the USB3_APPLICATION_CODE from BIOS ROM area and program certain registers.
//
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REGA0, AccessWidth32, 0x00000000, (SPI_HEAD_LENGTH << 16));
BcdAddress = ACPIMMIO16 (XhciFwStarting + BCD_ADDR_OFFSET);
BcdSize = ACPIMMIO16 (XhciFwStarting + BCD_SIZE_OFFSET);
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REGA4, AccessWidth16, 0x0000, BcdAddress);
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REGA4 + 2, AccessWidth16, 0x0000, BcdSize);
AcdAddress = ACPIMMIO16 (XhciFwStarting + ACD_ADDR_OFFSET);
AcdSize = ACPIMMIO16 (XhciFwStarting + ACD_SIZE_OFFSET);
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REGA8, AccessWidth16, 0x0000, AcdAddress);
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REGA8 + 2, AccessWidth16, 0x0000, AcdSize);
SpiValidBase = SPI_BASE2 (XhciFwStarting + 4) | SPI_BAR0_VLD | SPI_BASE0 | SPI_BAR1_VLD | SPI_BASE1 | SPI_BAR2_VLD;
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REGB0, AccessWidth32, 0x00000000, SpiValidBase);
//
// Copy Type0/1/2 data block from ROM image to MMIO starting from 0xC0
//
for (Index = 0; Index < SPI_HEAD_LENGTH; Index++) {
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REGC0 + Index, AccessWidth8, 0, ACPIMMIO8 (XhciFwStarting + Index));
}
for (Index = 0; Index < BcdSize; Index++) {
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REGC0 + SPI_HEAD_LENGTH + Index, AccessWidth8, 0, ACPIMMIO8 (XhciFwStarting + BcdAddress + Index));
}
for (Index = 0; Index < AcdSize; Index++) {
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REGC0 + SPI_HEAD_LENGTH + BcdSize + Index, AccessWidth8, 0, ACPIMMIO8 (XhciFwStarting + AcdAddress + Index));
}
//
// Step 3. to enable the instruction RAM preload functionality.
//
FwAddress = ACPIMMIO16 (XhciFwStarting + FW_ADDR_OFFSET);
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REGB4, AccessWidth16, 0x0000, ACPIMMIO16 (XhciFwStarting + FwAddress));
FwAddress += 2;
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG04, AccessWidth16, 0x0000, FwAddress);
FwSize = ACPIMMIO16 (XhciFwStarting + FW_SIZE_OFFSET);
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG04 + 2, AccessWidth16, 0x0000, FwSize);
//
// Set the starting address offset for Instruction RAM preload.
//
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG08, AccessWidth16, 0x0000, 0);
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG00, AccessWidth32, ~(UINT32) BIT29, BIT29);
for (;;) {
ReadMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG00 , AccessWidth32, &RegData);
if (RegData & BIT30) {
break;
}
}
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG00, AccessWidth32, ~(UINT32) BIT29, 0);
//
// Step 4. to release resets in XHCI_ACPI_MMIO_AMD_REG00. wait for USPLL to lock by polling USPLL lock.
//
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG00, AccessWidth32, ~(UINT32) U3PLL_RESET, 0); ///Release U3PLLreset
for (;;) {
ReadMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG00 , AccessWidth32, &RegData);
if (RegData & U3PLL_LOCK) {
break;
}
}
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG00, AccessWidth32, ~(UINT32) U3PHY_RESET, 0); ///Release U3PHY
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG00, AccessWidth32, ~(UINT32) U3CORE_RESET, 0); ///Release core reset
//
// SuperSpeed PHY Configuration
//
//RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG90, AccessWidth32, 0xFFF00000, 0x000AAAAA);
//RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REGD0, AccessWidth32, 0xFFF00000, 0x000AAAAA);
FchXhciInitIndirectReg (LocalCfgPtr);
RwMem (ACPI_MMIO_BASE + PMIO_BASE + FCH_PMIOA_REGEF, AccessWidth8, ~(UINT32) (BIT4 + BIT5), 0); /// Disable Device 22
RwMem (ACPI_MMIO_BASE + PMIO_BASE + FCH_PMIOA_REGEF, AccessWidth8, ~(UINT32) (BIT7), BIT7); /// Enable 2.0 devices
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG00, AccessWidth32, ~(UINT32) (BIT21), BIT21);
//
// Step 5.
//
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG00, AccessWidth32, ~(UINT32) (BIT17 + BIT18 + BIT19), BIT17 + BIT18);
//
// PLUG/UNPLUG of USB 2.0 devices make the XHCI USB 2.0 ports unfunctional - fix enable
// ACPI_USB3.0_REG 0x20[12:11] = 2'b11
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG20, AccessWidth32, ~((UINT32) (0x3 << 11)), (UINT32) (0x3 << 11));
//
// XHC 2 USB2 ports interactional issue - fix enable
// ACPI_USB3.0_REG 0x20[16] = 1'b1
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG20, AccessWidth32, ~((UINT32) (0x1 << 16)), (UINT32) (0x1 << 16));
//
// XHC USB2.0 Ports suspend Enhancement
// ACPI_USB3.0_REG 0x20[15] = 1'b1
//
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG20, AccessWidth32, ~((UINT32) (0x1 << 15)), (UINT32) (0x1 << 15));
//
// XHC HS/FS IN Data Buffer Underflow issue - fix enable
// ACPI_USB3.0_REG 0x20[20:18] = 0x7
//
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG20, AccessWidth32, ~((UINT32) (0x7 << 18)), (UINT32) (0x7 << 18));
//
// XHC stuck in U3 after system resuming from S3 -fix enable
// ACPI_USB3.0_REG 0x98[19] = 1'b1
//
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG98, AccessWidth32, ~((UINT32) (0x1 << 19)), (UINT32) (0x1 << 19));
//
// Change XHC1 ( Dev 16 function 1) Interrupt Pin register to INTB# - Fix enable
// ACPI_PMIO_F0[18] =1
//
RwMem (ACPI_MMIO_BASE + PMIO_BASE + FCH_PMIOA_REGF0, AccessWidth32, ~((UINT32) (0x1 << 18)), (UINT32) (0x1 << 18));
//
// EHCI3/OHCI3 blocks Blink Global Clock Gating when EHCI/OHCI Dev 22 fn 0/2 are disabled
// ACPI_PMIO_F0[13] =1
//
RwMem (ACPI_MMIO_BASE + PMIO_BASE + FCH_PMIOA_REGF0, AccessWidth32, ~((UINT32) (0x1 << 13)), (UINT32) (0x1 << 13));
//
// Access register through JTAG fail when switch from XHCI to EHCI/OHCI - Fix enable
// ACPI_PMIO_F0[17] =1
//
RwMem (ACPI_MMIO_BASE + PMIO_BASE + FCH_PMIOA_REGF0, AccessWidth32, ~((UINT32) (0x1 << 17)), (UINT32) (0x1 << 17));
//
// USB leakage current on differential lines when ports are switched to XHCI - Fix enable
// ACPI_PMIO_F0[14] =1
//
RwMem (ACPI_MMIO_BASE + PMIO_BASE + FCH_PMIOA_REGF0, AccessWidth32, ~((UINT32) (0x1 << 14)), (UINT32) (0x1 << 14));
// RRG 8.26 XHCI Clear pending PME on Sx entry
RwXhciIndReg ( FCH_XHCI_IND_REG54, ~(UINT32) (BIT15), BIT15, StdHeader);
//
// UMI Lane Configuration Information for XHCI Firmware to Calculate the Bandwidth for USB 3.0 ISOC Devices
//
if (!(IsUmiOneLaneGen1Mode (StdHeader))) {
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG20, AccessWidth32, ~(UINT32) (BIT25 + BIT24), BIT24);
}
// RPR 8.23 FS/LS devices not functional after resume from S4 fix enable (SB02699)
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG20, AccessWidth32, ~(UINT32) (BIT22), BIT22);
// RPR 8.24 XHC USB2.0 Hub disable issue fix enable (SB02702)
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REGB4, AccessWidth32, ~(UINT32) (BIT20), BIT20);
if ( ReadFchChipsetRevision ( FchDataPtr->StdHeader ) >= FCH_BOLTON ) {
// RPR 8.27 Enhance D3Cold ccu sequencing
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG10, AccessWidth32, ~(UINT32) (BIT11), BIT11);
// RPR 8.28 Set HCIVERSION to 1.0
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG30, AccessWidth32, ~(UINT32) (BIT15), BIT15);
// RPR 8.29 xHCI 1.0 Sub-Features Supported
// Blobk Event Interrupt Flag (BEI)
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG30, AccessWidth32, ~(UINT32) (BIT1), BIT1);
// Force Stopped Event (FSE)
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG30, AccessWidth32, ~(UINT32) (BIT2), BIT2);
// Software LPM
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG30, AccessWidth32, ~(UINT32) (BIT3), BIT3);
// Hardware LPM
// Skip TRB IOC Event
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG30, AccessWidth32, ~(UINT32) (BIT6), BIT6);
// Remove Secondary Bandwith Domain Reporting
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG30, AccessWidth32, ~(UINT32) (BIT7), BIT7);
// Cold Attach Status
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG30, AccessWidth32, ~(UINT32) (BIT8), BIT8);
// Endpoint Status Update Ordering
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG30, AccessWidth32, ~(UINT32) (BIT9), BIT9);
// Report Event during SKIP on Missed Service Error
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG30, AccessWidth32, ~(UINT32) (BIT10), BIT10);
// Soft Retry
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG30, AccessWidth32, ~(UINT32) (BIT11), BIT11);
// U3 Exit
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG30, AccessWidth32, ~(UINT32) (BIT12), BIT12);
// USB3.0 Link Command
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG30, AccessWidth32, ~(UINT32) (BIT13), BIT13);
// MSE FrameId invalid
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG30, AccessWidth32, ~(UINT32) (BIT14), BIT14);
// Port Test Mode
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG30, AccessWidth32, ~(UINT32) (BIT16), BIT16);
// Miscellaneous Design Improvements
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG40, AccessWidth32, ~(UINT32) (BIT0), BIT0);
//RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG40, AccessWidth32, ~(UINT32) (BIT25), 0);
// RRG 8.29 End
// RRG 8.30 XHC USB2 Loopback RX SE0
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG20, AccessWidth32, ~(UINT32) (BIT13 + BIT14 + BIT21), BIT13 + BIT14 + BIT21);
// RRG 8.31 XHC U2IF_Enabled_Quiettermination off
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REGB4, AccessWidth32, ~(UINT32) (BIT20), BIT20);
// RRG 8.32 XHC S0 BLM Reset Mode
RwMem (ACPI_MMIO_BASE + PMIO_BASE + FCH_PMIOA_REGF2, AccessWidth8, ~(UINT32) (BIT3), BIT3);
// RRG 8.33 Enhance XHC Ent_Flag
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REGB4, AccessWidth32, ~(UINT32) (BIT22), BIT22);
// RRG 8.34 Enhance TRB Pointer when both MSE and SKIP TRB IOC evt opened
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG30, AccessWidth32, ~(UINT32) (BIT17), BIT17);
// RRG 8.35 LPM Broadcast disable
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG30, AccessWidth32, ~(UINT32) (BIT18), BIT18);
// RRG 8.37 Enhance XHC FS/LS connect
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REGB4, AccessWidth32, ~(UINT32) (BIT24), BIT24);
// RRG 8.38 Enhance XHC ISOCH td_cmp
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REGB4, AccessWidth32, ~(UINT32) (BIT25), BIT25);
// RRG 8.39 LPM Clock 5us Select
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG24, AccessWidth32, ~(UINT32) (BIT8), BIT8);
// RRG 8.40 Enhance DPP ERR as XactErr
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG24, AccessWidth32, ~(UINT32) (BIT9), BIT9);
// RRG 8.41 Enhance U2IF PME Enable
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG24, AccessWidth32, ~(UINT32) (BIT10), BIT10);
// RRG 8.42 U2IF S3 Disconnect detection
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG24, AccessWidth32, ~(UINT32) (BIT12), BIT12);
// RRG 8.43 Stream Error Handling
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG30, AccessWidth32, ~(UINT32) (BIT20 + BIT21 + BIT22), (BIT20 + BIT21 + BIT22));
// RRG 8.44 FLA Deassert
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG30, AccessWidth32, ~(UINT32) (BIT23), BIT23);
// RRG 8.45 LPM Ctrl Improve
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG30, AccessWidth32, ~(UINT32) (BIT27), BIT27);
// 393674 Enable fix for control transfer error
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG30, AccessWidth32, ~(UINT32) (BIT24), BIT24);
//8.60 Enhance LPM Host initial L1 Exit
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG30, AccessWidth32, ~(UINT32) BIT29, BIT29);
// RRG 8.46 Enhance resume after disconnect
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG98, AccessWidth32, ~(UINT32) (BIT30), BIT30);
// RRG 8.47 Enhance SS HD Detected on Plug-in during S3
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG98, AccessWidth32, ~(UINT32) (BIT31), BIT31);
// RRG 8.48 Frame Babble Reporting
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REGB4, AccessWidth32, ~(UINT32) (BIT27), BIT27);
// xHCI Debug Capability
// RRG 8.49 DCP Halt RSTSM OFF
// RRG 8.50 Enable DCP DPH check
// RRG 8.51 DCP LTSSM Inactive to Rxdetect
// RRG 8.52 Enhance DCP EP State
// RRG 8.53 DCP Remote Wakeup Capable
// RRG 8.58 Enable ERDY send once DBC detectes HIT/HOT
// RRG 8.59 Block HIT/HOT until service interval done
//RegData = FCH_XHCI_IND_REG100;
//WriteMem ( ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG48, AccessWidth32, &RegData);
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG48, AccessWidth32, 0x00000000, FCH_XHCI_IND_REG100);
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG4C, AccessWidth32, ~(UINT32) (BIT0 + BIT1 + BIT2), BIT0 + BIT1 + BIT2);
//RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG4C, AccessWidth32, ~(UINT32) (BIT0 + BIT1 + BIT2), BIT0 + BIT1 + BIT2);
//ReadMem ( ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG4C, AccessWidth32, &RegData);
//RegData = FCH_XHCI_IND_REG120;
//WriteMem ( ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG48, AccessWidth32, &RegData);
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG48, AccessWidth32, 0x00000000, FCH_XHCI_IND_REG120);
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG4C, AccessWidth32, ~(UINT32) (BIT3), BIT3);
//RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG4C, AccessWidth32, ~(UINT32) (BIT3), BIT3);
//ReadMem ( ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG4C, AccessWidth32, &RegData);
//RegData = FCH_XHCI_IND_REG100;
//WriteMem ( ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG48, AccessWidth32, &RegData);
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG48, AccessWidth32, 0x00000000, FCH_XHCI_IND_REG100);
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG4C, AccessWidth32, ~(UINT32) (BIT21), BIT21);
//RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG4C, AccessWidth32, ~(UINT32) (BIT21), BIT21);
//ReadMem ( ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG4C, AccessWidth32, &RegData);
//RegData = FCH_XHCI_IND_REG128;
//WriteMem ( ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG48, AccessWidth32, &RegData);
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG48, AccessWidth32, 0x00000000, FCH_XHCI_IND_REG128);
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG4C, AccessWidth32, ~(UINT32) (BIT0), BIT0);
//RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG4C, AccessWidth32, ~(UINT32) (BIT0), BIT0);
//ReadMem ( ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG4C, AccessWidth32, &RegData);
//RegData = FCH_XHCI_IND_REG100;
//WriteMem ( ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG48, AccessWidth32, &RegData);
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG48, AccessWidth32, 0x00000000, FCH_XHCI_IND_REG100);
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG4C, AccessWidth32, ~(UINT32) (BIT3 + BIT4), BIT3 + BIT4);
//RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG4C, AccessWidth32, ~(UINT32) (BIT3 + BIT4), BIT3 + BIT4);
//ReadMem ( ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG4C, AccessWidth32, &RegData);
// RRG 8.54 Enhance SS HS detected during S3
//RegData = FCH_XHCI_IND_REG48;
//WriteMem ( ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG48, AccessWidth32, &RegData);
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG48, AccessWidth32, 0x00000000, FCH_XHCI_IND_REG48);
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG4C, AccessWidth32, ~(UINT32) (BIT1), BIT1);
// RRG 8.55 Enhance U1 timer (shorten U1 exit response time)
//RegData = FCH_XHCI_IND_REG48;
//WriteMem ( ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG48, AccessWidth32, &RegData);
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG48, AccessWidth32, 0x00000000, FCH_XHCI_IND_REG48);
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG4C, AccessWidth32, ~(UINT32) (BIT14), BIT14);
// RRG 8.56 Enhance HW LPM U2Entry state
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG24, AccessWidth32, ~(UINT32) (BIT17), BIT17);
// RRG 8.57 Enhance SSIF PME
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG24, AccessWidth32, ~(UINT32) (BIT14), BIT14);
// RPR 8.62 Enable FW enhancement on XHC clock control when memory power saving is disabled
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG10, AccessWidth32, ~(UINT32) (BIT13), BIT13);
// RPR 8.63 U2IF Remote Wake Select
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG24, AccessWidth32, ~(UINT32) (BIT11), BIT11);
// RPR 8.64 HS Data Toggle Error Handling
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG24, AccessWidth32, ~(UINT32) (BIT16), BIT16);
// A1
// UBTS 444589 PIL failures when reset device command hit link td points to invaild trb
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG28, AccessWidth32, ~(UINT32) (BIT3), BIT3);
// UBTS 437021 PME not generated by U2IF logic during S3 shutdown
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG24, AccessWidth32, ~(UINT32) (BIT30 + BIT31), (BIT30 + BIT31));
// UBTS 432864 When a USB3 device is disconnected, and connected again, xHC cannot detect it.
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG48, AccessWidth32, 0x00000000, FCH_XHCI_IND_REG48);
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG4C, AccessWidth32, ~(UINT32) (BIT16), BIT16);
// UBTS 430710 USB3 port enters compliance state when debug port enabled (0: enable)
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG24, AccessWidth32, ~(UINT32) (BIT27), BIT27);
// UBTS 430715 [DbC] Compatibility issue with 3rd party (I) chip as Host and AMD as Target
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG48, AccessWidth32, 0x00000000, FCH_XHCI_IND_REG100);
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG4C, AccessWidth32, ~(UINT32) (BIT5), BIT5);
// UBTS 430708 The second configure endpoint command haven't been executed completely when the port was in L1
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG24, AccessWidth32, ~(UINT32) (BIT26), BIT26);
// UBTS 428048 [LPM] LPM 2ports interrupt in is ERROR after host initiate L1exit respond a nak in HS
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG24, AccessWidth32, ~(UINT32) (BIT23), 0);
// UBTS 428045 LPM packet with incorrect address
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG24, AccessWidth32, ~(UINT32) (BIT22 + BIT24 + BIT25), 0);
// UBTS 443139 Buffer overrun during S4 loop
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG48, AccessWidth32, 0x00000000, FCH_XHCI_IND_REG48);
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG4C, AccessWidth32, ~(UINT32) (BIT17), BIT17);
// UBTS 419582 LPM arbitration between USB ports
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG24, AccessWidth32, ~(UINT32) (BIT21), 0);
// UBTS 429765 USB3.0 ACPI Indirect registers get changed after reboot
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG28, AccessWidth32, ~(UINT32) (BIT0), BIT0);
// UBTS 439658 Black Magic USB 3.0 device when enabled/disabled under windows causes the driver to register disconnect
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG28, AccessWidth32, ~(UINT32) (BIT1 + BIT2), BIT2);
// UBTS SS RX terminations blocked unexpectedly
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG24, AccessWidth32, ~(UINT32) (BIT15), BIT15);
}
}
/**
* FchXhciInitBeforePciInit - Config XHCI controller before PCI
* emulation
*
*
*
* @param[in] FchDataPtr Fch configuration structure pointer.
*
*/
VOID
FchXhciInitBeforePciInit (
IN FCH_DATA_BLOCK *FchDataPtr
)
{
UINT16 BcdAddress;
UINT16 BcdSize;
UINT16 AcdAddress;
UINT16 AcdSize;
UINT16 FwAddress;
UINT16 FwSize;
UINTN XhciFwStarting;
UINT32 SpiValidBase;
UINT32 RegData;
UINT16 Index;
BOOLEAN Xhci0Enable;
BOOLEAN Xhci1Enable;
FCH_DATA_BLOCK *LocalCfgPtr;
AMD_CONFIG_PARAMS *StdHeader;
LocalCfgPtr = (FCH_DATA_BLOCK *)FchDataPtr;
StdHeader = LocalCfgPtr->StdHeader;
Xhci0Enable = LocalCfgPtr->Usb.Xhci0Enable;
Xhci1Enable = LocalCfgPtr->Usb.Xhci1Enable;
if (( Xhci0Enable == 0 ) && (Xhci1Enable == 0)) {
return;
}
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG00, AccessWidth32, 0x00000000, 0x00400700);
FchStall (20, StdHeader);
if ( LocalCfgPtr->Usb.UserDefineXhciRomAddr == 0 ) {
//
// Get ROM SIG starting address for USB firmware starting address (offset 0x0C to SIG address)
//
GetRomSigPtr (&XhciFwStarting, StdHeader);
if (XhciFwStarting == 0) {
return;
}
XhciFwStarting = ACPIMMIO32 (XhciFwStarting + FW_TO_SIGADDR_OFFSET);
} else {
XhciFwStarting = ( UINTN ) LocalCfgPtr->Usb.UserDefineXhciRomAddr;
}
if (IsLpcRom ()) {
//
// XHCI firmware re-load
//
RwPci ((LPC_BUS_DEV_FUN << 16) + FCH_LPC_REGCC, AccessWidth32, (UINT32)~BIT2, (UINT32)(BIT2 + BIT1 + BIT0), StdHeader);
RwPci ((LPC_BUS_DEV_FUN << 16) + FCH_LPC_REGCC, AccessWidth32, 0x00000FFF, (UINT32) (XhciFwStarting), StdHeader);
}
//
// Enable SuperSpeed receive special error case logic. 0x20 bit8
// Enable USB2.0 RX_Valid Synchronization. 0x20 bit9
// Enable USB2.0 DIN/SE0 Synchronization. 0x20 bit10
//
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG20, AccessWidth32, 0xFFFFF8FF, 0x00000700);
//
// SuperSpeed PHY Configuration (adaptation timer setting)
// XHC U1 LFPS Exit time
//
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG90, AccessWidth32, 0xCFF00000, 0x000AAAAA);
//RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG90 + 0x40, AccessWidth32, 0xFFF00000, 0x000AAAAA);
//
// Step 1. to enable Xhci IO and Firmware load mode
//
RwMem (ACPI_MMIO_BASE + PMIO_BASE + FCH_PMIOA_REGEF, AccessWidth8, (UINT32)~(BIT4 + BIT5), 0); /// Disable Device 22
RwMem (ACPI_MMIO_BASE + PMIO_BASE + FCH_PMIOA_REGEF, AccessWidth8, (UINT32)~(BIT7), (UINT32)BIT7); /// Enable 2.0 devices
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG00, AccessWidth32, 0xF0FFFFFC, (Xhci0Enable + (Xhci1Enable << 1)) & 0x03);
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG00, AccessWidth32, 0xEFFFFFFF, 0x10000000);
//
// Step 2. to read a portion of the USB3_APPLICATION_CODE from BIOS ROM area and program certain registers.
//
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REGA0, AccessWidth32, 0x00000000, (SPI_HEAD_LENGTH << 16));
BcdAddress = ACPIMMIO16 (XhciFwStarting + BCD_ADDR_OFFSET);
BcdSize = ACPIMMIO16 (XhciFwStarting + BCD_SIZE_OFFSET);
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REGA4, AccessWidth16, 0x0000, BcdAddress);
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REGA4 + 2, AccessWidth16, 0x0000, BcdSize);
AcdAddress = ACPIMMIO16 (XhciFwStarting + ACD_ADDR_OFFSET);
AcdSize = ACPIMMIO16 (XhciFwStarting + ACD_SIZE_OFFSET);
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REGA8, AccessWidth16, 0x0000, AcdAddress);
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REGA8 + 2, AccessWidth16, 0x0000, AcdSize);
SpiValidBase = SPI_BASE2 (XhciFwStarting + 4) | SPI_BAR0_VLD | SPI_BASE0 | SPI_BAR1_VLD | SPI_BASE1 | SPI_BAR2_VLD;
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REGB0, AccessWidth32, 0x00000000, SpiValidBase);
//
// Copy Type0/1/2 data block from ROM image to MMIO starting from 0xC0
//
for (Index = 0; Index < SPI_HEAD_LENGTH; Index++) {
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REGC0 + Index, AccessWidth8, 0, ACPIMMIO8 (XhciFwStarting + Index));
}
for (Index = 0; Index < BcdSize; Index++) {
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REGC0 + SPI_HEAD_LENGTH + Index, AccessWidth8, 0, ACPIMMIO8 (XhciFwStarting + BcdAddress + Index));
}
for (Index = 0; Index < AcdSize; Index++) {
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REGC0 + SPI_HEAD_LENGTH + BcdSize + Index, AccessWidth8, 0, ACPIMMIO8 (XhciFwStarting + AcdAddress + Index));
}
//
// Step 3. to enable the instruction RAM preload functionality.
//
FwAddress = ACPIMMIO16 (XhciFwStarting + FW_ADDR_OFFSET);
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REGB4, AccessWidth16, 0x0000, ACPIMMIO16 (XhciFwStarting + FwAddress));
FwAddress += 2;
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG04, AccessWidth16, 0x0000, FwAddress);
FwSize = ACPIMMIO16 (XhciFwStarting + FW_SIZE_OFFSET);
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG04 + 2, AccessWidth16, 0x0000, FwSize);
//
// Set the starting address offset for Instruction RAM preload.
//
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG08, AccessWidth16, 0x0000, 0);
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG00, AccessWidth32, (UINT32)~BIT29, (UINT32)BIT29);
for (;;) {
ReadMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG00 , AccessWidth32, &RegData);
if (RegData & BIT30) {
break;
}
}
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG00, AccessWidth32, (UINT32)~BIT29, 0);
//
// Step 4. to release resets in XHCI_ACPI_MMIO_AMD_REG00. wait for USPLL to lock by polling USPLL lock.
//
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG00, AccessWidth32, (UINT32)~U3PLL_RESET, 0); ///Release U3PLLreset
for (;;) {
ReadMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG00 , AccessWidth32, &RegData);
if (RegData & U3PLL_LOCK) {
break;
}
}
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG00, AccessWidth32, (UINT32)~U3PHY_RESET, 0); ///Release U3PHY
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG00, AccessWidth32, (UINT32)~U3CORE_RESET, 0); ///Release core reset
//
// SuperSpeed PHY Configuration
//
//RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG90, AccessWidth32, 0xFFF00000, 0x000AAAAA);
//RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REGD0, AccessWidth32, 0xFFF00000, 0x000AAAAA);
FchXhciInitIndirectReg (StdHeader);
RwMem (ACPI_MMIO_BASE + PMIO_BASE + FCH_PMIOA_REGEF, AccessWidth8, (UINT32)~(BIT4 + BIT5), 0); /// Disable Device 22
RwMem (ACPI_MMIO_BASE + PMIO_BASE + FCH_PMIOA_REGEF, AccessWidth8, (UINT32)~(BIT7), (UINT32)BIT7); /// Enable 2.0 devices
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG00, AccessWidth32, (UINT32)~(BIT21), (UINT32)BIT21);
//
// Step 5.
//
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG00, AccessWidth32, (UINT32)~(BIT17 + BIT18 + BIT19), (UINT32)(BIT17 + BIT18));
XhciA12Fix ();
//
// UMI Lane Configuration Information for XHCI Firmware to Calculate the Bandwidth for USB 3.0 ISOC Devices
//
if (!(IsUmiOneLaneGen1Mode (StdHeader))) {
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG20, AccessWidth32, (UINT32)~(BIT25 + BIT24), (UINT32)BIT24);
}
// RPR 8.23 FS/LS devices not functional after resume from S4 fix enable (SB02699)
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REG20, AccessWidth32, (UINT32)~(BIT22), (UINT32)BIT22);
// RPR 8.24 XHC USB2.0 Hub disable issue fix enable (SB02702)
RwMem (ACPI_MMIO_BASE + XHCI_BASE + XHCI_ACPI_MMIO_AMD_REGB4, AccessWidth32, (UINT32)~(BIT20), (UINT32)BIT20);
}