static void xhci_print_cap_regs(struct xhci_hcd *xhci)
{
u32 temp;
xhci_dbg(xhci, "xHCI capability registers at %p:\n", xhci->cap_regs);
temp = xhci_readl(xhci, &xhci->cap_regs->hc_capbase);
xhci_dbg(xhci, "CAPLENGTH AND HCIVERSION 0x%x:\n",
(unsigned int) temp);
xhci_dbg(xhci, "CAPLENGTH: 0x%x\n",
(unsigned int) HC_LENGTH(temp));
xhci_dbg(xhci, "HCIVERSION: 0x%x\n",
(unsigned int) HC_VERSION(temp));
temp = xhci_readl(xhci, &xhci->cap_regs->hcs_params1);
xhci_dbg(xhci, "HCSPARAMS 1: 0x%x\n",
(unsigned int) temp);
xhci_dbg(xhci, " Max device slots: %u\n",
(unsigned int) HCS_MAX_SLOTS(temp));
xhci_dbg(xhci, " Max interrupters: %u\n",
(unsigned int) HCS_MAX_INTRS(temp));
xhci_dbg(xhci, " Max ports: %u\n",
(unsigned int) HCS_MAX_PORTS(temp));
temp = xhci_readl(xhci, &xhci->cap_regs->hcs_params2);
xhci_dbg(xhci, "HCSPARAMS 2: 0x%x\n",
(unsigned int) temp);
xhci_dbg(xhci, " Isoc scheduling threshold: %u\n",
(unsigned int) HCS_IST(temp));
xhci_dbg(xhci, " Maximum allowed segments in event ring: %u\n",
(unsigned int) HCS_ERST_MAX(temp));
temp = xhci_readl(xhci, &xhci->cap_regs->hcs_params3);
xhci_dbg(xhci, "HCSPARAMS 3 0x%x:\n",
(unsigned int) temp);
xhci_dbg(xhci, " Worst case U1 device exit latency: %u\n",
(unsigned int) HCS_U1_LATENCY(temp));
xhci_dbg(xhci, " Worst case U2 device exit latency: %u\n",
(unsigned int) HCS_U2_LATENCY(temp));
temp = xhci_readl(xhci, &xhci->cap_regs->hcc_params);
xhci_dbg(xhci, "HCC PARAMS 0x%x:\n", (unsigned int) temp);
xhci_dbg(xhci, " HC generates %s bit addresses\n",
HCC_64BIT_ADDR(temp) ? "64" : "32");
/* FIXME */
xhci_dbg(xhci, " FIXME: more HCCPARAMS debugging\n");
temp = xhci_readl(xhci, &xhci->cap_regs->run_regs_off);
xhci_dbg(xhci, "RTSOFF 0x%x:\n", temp & RTSOFF_MASK);
}
int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
u16 wIndex, char *buf, u16 wLength)
{
struct xhci_hcd *xhci = hcd_to_xhci(hcd);
int max_ports;
unsigned long flags;
u32 temp, status;
int retval = 0;
__le32 __iomem **port_array;
int slot_id;
struct xhci_bus_state *bus_state;
u16 link_state = 0;
u16 wake_mask = 0;
max_ports = xhci_get_ports(hcd, &port_array);
bus_state = &xhci->bus_state[hcd_index(hcd)];
spin_lock_irqsave(&xhci->lock, flags);
switch (typeReq) {
case GetHubStatus:
/* No power source, over-current reported per port */
memset(buf, 0, 4);
break;
case GetHubDescriptor:
/* Check to make sure userspace is asking for the USB 3.0 hub
* descriptor for the USB 3.0 roothub. If not, we stall the
* endpoint, like external hubs do.
*/
if (hcd->speed == HCD_USB3 &&
(wLength < USB_DT_SS_HUB_SIZE ||
wValue != (USB_DT_SS_HUB << 8))) {
xhci_dbg(xhci, "Wrong hub descriptor type for "
"USB 3.0 roothub.\n");
goto error;
}
xhci_hub_descriptor(hcd, xhci,
(struct usb_hub_descriptor *) buf);
break;
case DeviceRequest | USB_REQ_GET_DESCRIPTOR:
if ((wValue & 0xff00) != (USB_DT_BOS << 8))
goto error;
if (hcd->speed != HCD_USB3)
goto error;
memcpy(buf, &usb_bos_descriptor,
USB_DT_BOS_SIZE + USB_DT_USB_SS_CAP_SIZE);
temp = xhci_readl(xhci, &xhci->cap_regs->hcs_params3);
buf[12] = HCS_U1_LATENCY(temp);
put_unaligned_le16(HCS_U2_LATENCY(temp), &buf[13]);
spin_unlock_irqrestore(&xhci->lock, flags);
return USB_DT_BOS_SIZE + USB_DT_USB_SS_CAP_SIZE;
case GetPortStatus:
if (!wIndex || wIndex > max_ports)
goto error;
wIndex--;
status = 0;
temp = xhci_readl(xhci, port_array[wIndex]);
if (temp == 0xffffffff) {
retval = -ENODEV;
break;
}
xhci_dbg(xhci, "get port status, actual port %d status = 0x%x\n", wIndex, temp);
/* wPortChange bits */
if (temp & PORT_CSC)
status |= USB_PORT_STAT_C_CONNECTION << 16;
if (temp & PORT_PEC)
status |= USB_PORT_STAT_C_ENABLE << 16;
if ((temp & PORT_OCC))
status |= USB_PORT_STAT_C_OVERCURRENT << 16;
if ((temp & PORT_RC))
status |= USB_PORT_STAT_C_RESET << 16;
/* USB3.0 only */
if (hcd->speed == HCD_USB3) {
if ((temp & PORT_PLC))
status |= USB_PORT_STAT_C_LINK_STATE << 16;
if ((temp & PORT_WRC))
status |= USB_PORT_STAT_C_BH_RESET << 16;
}
if (hcd->speed != HCD_USB3) {
if ((temp & PORT_PLS_MASK) == XDEV_U3
&& (temp & PORT_POWER))
status |= USB_PORT_STAT_SUSPEND;
}
if ((temp & PORT_PLS_MASK) == XDEV_RESUME &&
!DEV_SUPERSPEED(temp)) {
if ((temp & PORT_RESET) || !(temp & PORT_PE))
goto error;
if (time_after_eq(jiffies,
bus_state->resume_done[wIndex])) {
xhci_dbg(xhci, "Resume USB2 port %d\n",
wIndex + 1);
bus_state->resume_done[wIndex] = 0;
xhci_set_link_state(xhci, port_array, wIndex,
XDEV_U0);
xhci_dbg(xhci, "set port %d resume\n",
wIndex + 1);
slot_id = xhci_find_slot_id_by_port(hcd, xhci,
wIndex + 1);
if (!slot_id) {
xhci_dbg(xhci, "slot_id is zero\n");
goto error;
}
xhci_ring_device(xhci, slot_id);
bus_state->port_c_suspend |= 1 << wIndex;
bus_state->suspended_ports &= ~(1 << wIndex);
} else {
/*
* The resume has been signaling for less than
* 20ms. Report the port status as SUSPEND,
* let the usbcore check port status again
* and clear resume signaling later.
*/
status |= USB_PORT_STAT_SUSPEND;
}
}
if ((temp & PORT_PLS_MASK) == XDEV_U0
&& (temp & PORT_POWER)
&& (bus_state->suspended_ports & (1 << wIndex))) {
bus_state->suspended_ports &= ~(1 << wIndex);
if (hcd->speed != HCD_USB3)
bus_state->port_c_suspend |= 1 << wIndex;
}
if (temp & PORT_CONNECT) {
status |= USB_PORT_STAT_CONNECTION;
status |= xhci_port_speed(temp);
}
if (temp & PORT_PE)
status |= USB_PORT_STAT_ENABLE;
if (temp & PORT_OC)
status |= USB_PORT_STAT_OVERCURRENT;
if (temp & PORT_RESET)
status |= USB_PORT_STAT_RESET;
if (temp & PORT_POWER) {
if (hcd->speed == HCD_USB3)
status |= USB_SS_PORT_STAT_POWER;
else
status |= USB_PORT_STAT_POWER;
}
/* Port Link State */
if (hcd->speed == HCD_USB3) {
/* resume state is a xHCI internal state.
* Do not report it to usb core.
*/
if ((temp & PORT_PLS_MASK) != XDEV_RESUME)
status |= (temp & PORT_PLS_MASK);
}
if (bus_state->port_c_suspend & (1 << wIndex))
status |= 1 << USB_PORT_FEAT_C_SUSPEND;
xhci_dbg(xhci, "Get port status returned 0x%x\n", status);
put_unaligned(cpu_to_le32(status), (__le32 *) buf);
break;
case SetPortFeature:
if (wValue == USB_PORT_FEAT_LINK_STATE)
link_state = (wIndex & 0xff00) >> 3;
if (wValue == USB_PORT_FEAT_REMOTE_WAKE_MASK)
wake_mask = wIndex & 0xff00;
wIndex &= 0xff;
if (!wIndex || wIndex > max_ports)
goto error;
wIndex--;
temp = xhci_readl(xhci, port_array[wIndex]);
if (temp == 0xffffffff) {
retval = -ENODEV;
break;
}
temp = xhci_port_state_to_neutral(temp);
/* FIXME: What new port features do we need to support? */
switch (wValue) {
case USB_PORT_FEAT_SUSPEND:
temp = xhci_readl(xhci, port_array[wIndex]);
if ((temp & PORT_PLS_MASK) != XDEV_U0) {
/* Resume the port to U0 first */
xhci_set_link_state(xhci, port_array, wIndex,
XDEV_U0);
spin_unlock_irqrestore(&xhci->lock, flags);
msleep(10);
spin_lock_irqsave(&xhci->lock, flags);
}
/* In spec software should not attempt to suspend
* a port unless the port reports that it is in the
* enabled (PED = ‘1’,PLS < ‘3’) state.
*/
temp = xhci_readl(xhci, port_array[wIndex]);
if ((temp & PORT_PE) == 0 || (temp & PORT_RESET)
|| (temp & PORT_PLS_MASK) >= XDEV_U3) {
xhci_warn(xhci, "USB core suspending device "
"not in U0/U1/U2.\n");
goto error;
}
slot_id = xhci_find_slot_id_by_port(hcd, xhci,
wIndex + 1);
if (!slot_id) {
xhci_warn(xhci, "slot_id is zero\n");
goto error;
}
/* unlock to execute stop endpoint commands */
spin_unlock_irqrestore(&xhci->lock, flags);
xhci_stop_device(xhci, slot_id, 1);
spin_lock_irqsave(&xhci->lock, flags);
xhci_set_link_state(xhci, port_array, wIndex, XDEV_U3);
spin_unlock_irqrestore(&xhci->lock, flags);
msleep(10); /* wait device to enter */
spin_lock_irqsave(&xhci->lock, flags);
temp = xhci_readl(xhci, port_array[wIndex]);
bus_state->suspended_ports |= 1 << wIndex;
break;
case USB_PORT_FEAT_LINK_STATE:
temp = xhci_readl(xhci, port_array[wIndex]);
/* Software should not attempt to set
* port link state above '5' (Rx.Detect) and the port
* must be enabled.
*/
if ((temp & PORT_PE) == 0 ||
(link_state > USB_SS_PORT_LS_RX_DETECT)) {
xhci_warn(xhci, "Cannot set link state.\n");
goto error;
}
if (link_state == USB_SS_PORT_LS_U3) {
slot_id = xhci_find_slot_id_by_port(hcd, xhci,
wIndex + 1);
if (slot_id) {
/* unlock to execute stop endpoint
* commands */
spin_unlock_irqrestore(&xhci->lock,
flags);
xhci_stop_device(xhci, slot_id, 1);
spin_lock_irqsave(&xhci->lock, flags);
}
}
xhci_set_link_state(xhci, port_array, wIndex,
link_state);
spin_unlock_irqrestore(&xhci->lock, flags);
msleep(20); /* wait device to enter */
spin_lock_irqsave(&xhci->lock, flags);
temp = xhci_readl(xhci, port_array[wIndex]);
if (link_state == USB_SS_PORT_LS_U3)
bus_state->suspended_ports |= 1 << wIndex;
break;
case USB_PORT_FEAT_POWER:
/*
* Turn on ports, even if there isn't per-port switching.
* HC will report connect events even before this is set.
* However, khubd will ignore the roothub events until
* the roothub is registered.
*/
xhci_writel(xhci, temp | PORT_POWER,
port_array[wIndex]);
if (xhci->quirks & XHCI_PORTSC_DELAY)
ndelay(100);
temp = xhci_readl(xhci, port_array[wIndex]);
xhci_dbg(xhci, "set port power, actual port %d status = 0x%x\n", wIndex, temp);
break;
case USB_PORT_FEAT_RESET:
temp = (temp | PORT_RESET);
xhci_writel(xhci, temp, port_array[wIndex]);
if (xhci->quirks & XHCI_PORTSC_DELAY)
ndelay(100);
temp = xhci_readl(xhci, port_array[wIndex]);
xhci_dbg(xhci, "set port reset, actual port %d status = 0x%x\n", wIndex, temp);
break;
case USB_PORT_FEAT_REMOTE_WAKE_MASK:
xhci_set_remote_wake_mask(xhci, port_array,
wIndex, wake_mask);
temp = xhci_readl(xhci, port_array[wIndex]);
xhci_dbg(xhci, "set port remote wake mask, "
"actual port %d status = 0x%x\n",
wIndex, temp);
break;
case USB_PORT_FEAT_BH_PORT_RESET:
temp |= PORT_WR;
xhci_writel(xhci, temp, port_array[wIndex]);
if (xhci->quirks & XHCI_PORTSC_DELAY)
ndelay(100);
temp = xhci_readl(xhci, port_array[wIndex]);
break;
default:
goto error;
}
/* unblock any posted writes */
temp = xhci_readl(xhci, port_array[wIndex]);
break;
case ClearPortFeature:
if (!wIndex || wIndex > max_ports)
goto error;
wIndex--;
temp = xhci_readl(xhci, port_array[wIndex]);
if (temp == 0xffffffff) {
retval = -ENODEV;
break;
}
/* FIXME: What new port features do we need to support? */
temp = xhci_port_state_to_neutral(temp);
switch (wValue) {
case USB_PORT_FEAT_SUSPEND:
temp = xhci_readl(xhci, port_array[wIndex]);
xhci_dbg(xhci, "clear USB_PORT_FEAT_SUSPEND\n");
xhci_dbg(xhci, "PORTSC %04x\n", temp);
if (temp & PORT_RESET)
goto error;
if ((temp & PORT_PLS_MASK) == XDEV_U3) {
if ((temp & PORT_PE) == 0)
goto error;
xhci_set_link_state(xhci, port_array, wIndex,
XDEV_RESUME);
spin_unlock_irqrestore(&xhci->lock, flags);
msleep(20);
spin_lock_irqsave(&xhci->lock, flags);
xhci_set_link_state(xhci, port_array, wIndex,
XDEV_U0);
}
bus_state->port_c_suspend |= 1 << wIndex;
slot_id = xhci_find_slot_id_by_port(hcd, xhci,
wIndex + 1);
if (!slot_id) {
xhci_dbg(xhci, "slot_id is zero\n");
goto error;
}
xhci_ring_device(xhci, slot_id);
break;
case USB_PORT_FEAT_C_SUSPEND:
bus_state->port_c_suspend &= ~(1 << wIndex);
case USB_PORT_FEAT_C_RESET:
case USB_PORT_FEAT_C_BH_PORT_RESET:
case USB_PORT_FEAT_C_CONNECTION:
case USB_PORT_FEAT_C_OVER_CURRENT:
case USB_PORT_FEAT_C_ENABLE:
case USB_PORT_FEAT_C_PORT_LINK_STATE:
xhci_clear_port_change_bit(xhci, wValue, wIndex,
port_array[wIndex], temp);
break;
case USB_PORT_FEAT_ENABLE:
xhci_disable_port(hcd, xhci, wIndex,
port_array[wIndex], temp);
break;
default:
goto error;
}
break;
default:
error:
/* "stall" on error */
retval = -EPIPE;
}
spin_unlock_irqrestore(&xhci->lock, flags);
return retval;
}
int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
u16 wIndex, char *buf, u16 wLength)
{
struct xhci_hcd *xhci = hcd_to_xhci(hcd);
int max_ports;
unsigned long flags;
u32 temp, status;
int retval = 0;
__le32 __iomem **port_array;
int slot_id;
struct xhci_bus_state *bus_state;
u16 link_state = 0;
u16 wake_mask = 0;
u32 __iomem *status_reg = NULL;
u32 i, command, num_ports, selector;
max_ports = xhci_get_ports(hcd, &port_array);
bus_state = &xhci->bus_state[hcd_index(hcd)];
spin_lock_irqsave(&xhci->lock, flags);
switch (typeReq) {
case GetHubStatus:
/* No power source, over-current reported per port */
memset(buf, 0, 4);
break;
case GetHubDescriptor:
/* Check to make sure userspace is asking for the USB 3.0 hub
* descriptor for the USB 3.0 roothub. If not, we stall the
* endpoint, like external hubs do.
*/
if (hcd->speed == HCD_USB3 &&
(wLength < USB_DT_SS_HUB_SIZE ||
wValue != (USB_DT_SS_HUB << 8))) {
xhci_dbg(xhci, "Wrong hub descriptor type for "
"USB 3.0 roothub.\n");
goto error;
}
xhci_hub_descriptor(hcd, xhci,
(struct usb_hub_descriptor *) buf);
break;
case DeviceRequest | USB_REQ_GET_DESCRIPTOR:
if ((wValue & 0xff00) != (USB_DT_BOS << 8))
goto error;
if (hcd->speed != HCD_USB3)
goto error;
memcpy(buf, &usb_bos_descriptor,
USB_DT_BOS_SIZE + USB_DT_USB_SS_CAP_SIZE);
temp = xhci_readl(xhci, &xhci->cap_regs->hcs_params3);
buf[12] = HCS_U1_LATENCY(temp);
put_unaligned_le16(HCS_U2_LATENCY(temp), &buf[13]);
spin_unlock_irqrestore(&xhci->lock, flags);
return USB_DT_BOS_SIZE + USB_DT_USB_SS_CAP_SIZE;
case GetPortStatus:
if (!wIndex || wIndex > max_ports)
goto error;
wIndex--;
status = 0;
temp = xhci_readl(xhci, port_array[wIndex]);
if (temp == 0xffffffff) {
retval = -ENODEV;
break;
}
xhci_dbg(xhci, "get port status, actual port %d status = 0x%x\n", wIndex, temp);
/* wPortChange bits */
if (temp & PORT_CSC)
status |= USB_PORT_STAT_C_CONNECTION << 16;
if (temp & PORT_PEC)
status |= USB_PORT_STAT_C_ENABLE << 16;
if ((temp & PORT_OCC))
status |= USB_PORT_STAT_C_OVERCURRENT << 16;
if ((temp & PORT_RC))
status |= USB_PORT_STAT_C_RESET << 16;
/* USB3.0 only */
if (hcd->speed == HCD_USB3) {
if ((temp & PORT_PLC))
status |= USB_PORT_STAT_C_LINK_STATE << 16;
if ((temp & PORT_WRC))
status |= USB_PORT_STAT_C_BH_RESET << 16;
}
if (hcd->speed != HCD_USB3) {
if ((temp & PORT_PLS_MASK) == XDEV_U3
&& (temp & PORT_POWER))
status |= USB_PORT_STAT_SUSPEND;
}
if ((temp & PORT_PLS_MASK) == XDEV_RESUME &&
!DEV_SUPERSPEED(temp)) {
if ((temp & PORT_RESET) || !(temp & PORT_PE))
goto error;
if (time_after_eq(jiffies,
bus_state->resume_done[wIndex])) {
xhci_dbg(xhci, "Resume USB2 port %d\n",
wIndex + 1);
bus_state->resume_done[wIndex] = 0;
clear_bit(wIndex, &bus_state->resuming_ports);
xhci_set_link_state(xhci, port_array, wIndex,
XDEV_U0);
xhci_dbg(xhci, "set port %d resume\n",
wIndex + 1);
slot_id = xhci_find_slot_id_by_port(hcd, xhci,
wIndex + 1);
if (!slot_id) {
xhci_dbg(xhci, "slot_id is zero\n");
goto error;
}
xhci_ring_device(xhci, slot_id);
bus_state->port_c_suspend |= 1 << wIndex;
bus_state->suspended_ports &= ~(1 << wIndex);
} else {
/*
* The resume has been signaling for less than
* 20ms. Report the port status as SUSPEND,
* let the usbcore check port status again
* and clear resume signaling later.
*/
status |= USB_PORT_STAT_SUSPEND;
}
}
if ((temp & PORT_PLS_MASK) == XDEV_U0
&& (temp & PORT_POWER)
&& (bus_state->suspended_ports & (1 << wIndex))) {
bus_state->suspended_ports &= ~(1 << wIndex);
if (hcd->speed != HCD_USB3)
bus_state->port_c_suspend |= 1 << wIndex;
}
if (temp & PORT_CONNECT) {
status |= USB_PORT_STAT_CONNECTION;
status |= xhci_port_speed(temp);
}
if (temp & PORT_PE)
status |= USB_PORT_STAT_ENABLE;
if (temp & PORT_OC)
status |= USB_PORT_STAT_OVERCURRENT;
if (temp & PORT_RESET)
status |= USB_PORT_STAT_RESET;
if (temp & PORT_POWER) {
if (hcd->speed == HCD_USB3)
status |= USB_SS_PORT_STAT_POWER;
else
status |= USB_PORT_STAT_POWER;
}
/* Update Port Link State for super speed ports*/
if (hcd->speed == HCD_USB3) {
xhci_hub_report_link_state(&status, temp);
/*
* Verify if all USB3 Ports Have entered U0 already.
* Delete Compliance Mode Timer if so.
*/
xhci_del_comp_mod_timer(xhci, temp, wIndex);
}
if (bus_state->port_c_suspend & (1 << wIndex))
status |= 1 << USB_PORT_FEAT_C_SUSPEND;
xhci_dbg(xhci, "Get port status returned 0x%x\n", status);
put_unaligned(cpu_to_le32(status), (__le32 *) buf);
break;
case SetPortFeature:
if (wValue == USB_PORT_FEAT_LINK_STATE)
link_state = (wIndex & 0xff00) >> 3;
if (wValue == USB_PORT_FEAT_REMOTE_WAKE_MASK)
wake_mask = wIndex & 0xff00;
selector = wIndex >> 8;
wIndex &= 0xff;
if (!wIndex || wIndex > max_ports)
goto error;
wIndex--;
status_reg = &xhci->op_regs->port_power_base +
NUM_PORT_REGS*wIndex;
temp = xhci_readl(xhci, port_array[wIndex]);
if (temp == 0xffffffff) {
retval = -ENODEV;
break;
}
temp = xhci_port_state_to_neutral(temp);
/* FIXME: What new port features do we need to support? */
switch (wValue) {
case USB_PORT_FEAT_SUSPEND:
temp = xhci_readl(xhci, port_array[wIndex]);
if ((temp & PORT_PLS_MASK) != XDEV_U0) {
/* Resume the port to U0 first */
xhci_set_link_state(xhci, port_array, wIndex,
XDEV_U0);
spin_unlock_irqrestore(&xhci->lock, flags);
msleep(10);
spin_lock_irqsave(&xhci->lock, flags);
}
/* In spec software should not attempt to suspend
* a port unless the port reports that it is in the
* enabled (PED = ‘1’,PLS < ‘3’) state.
*/
temp = xhci_readl(xhci, port_array[wIndex]);
if ((temp & PORT_PE) == 0 || (temp & PORT_RESET)
|| (temp & PORT_PLS_MASK) >= XDEV_U3) {
xhci_warn(xhci, "USB core suspending device "
"not in U0/U1/U2.\n");
goto error;
}
slot_id = xhci_find_slot_id_by_port(hcd, xhci,
wIndex + 1);
if (!slot_id) {
xhci_warn(xhci, "slot_id is zero\n");
goto error;
}
/* unlock to execute stop endpoint commands */
spin_unlock_irqrestore(&xhci->lock, flags);
xhci_stop_device(xhci, slot_id, 1);
spin_lock_irqsave(&xhci->lock, flags);
xhci_set_link_state(xhci, port_array, wIndex, XDEV_U3);
spin_unlock_irqrestore(&xhci->lock, flags);
msleep(10); /* wait device to enter */
spin_lock_irqsave(&xhci->lock, flags);
temp = xhci_readl(xhci, port_array[wIndex]);
bus_state->suspended_ports |= 1 << wIndex;
break;
case USB_PORT_FEAT_LINK_STATE:
temp = xhci_readl(xhci, port_array[wIndex]);
/* Disable port */
if (link_state == USB_SS_PORT_LS_SS_DISABLED) {
xhci_dbg(xhci, "Disable port %d\n", wIndex);
temp = xhci_port_state_to_neutral(temp);
/*
* Clear all change bits, so that we get a new
* connection event.
*/
temp |= PORT_CSC | PORT_PEC | PORT_WRC |
PORT_OCC | PORT_RC | PORT_PLC |
PORT_CEC;
xhci_writel(xhci, temp | PORT_PE,
port_array[wIndex]);
temp = xhci_readl(xhci, port_array[wIndex]);
break;
}
/* Put link in RxDetect (enable port) */
if (link_state == USB_SS_PORT_LS_RX_DETECT) {
xhci_dbg(xhci, "Enable port %d\n", wIndex);
xhci_set_link_state(xhci, port_array, wIndex,
link_state);
temp = xhci_readl(xhci, port_array[wIndex]);
break;
}
/* Software should not attempt to set
* port link state above '3' (U3) and the port
* must be enabled.
*/
if ((temp & PORT_PE) == 0 ||
(link_state > USB_SS_PORT_LS_U3)) {
xhci_warn(xhci, "Cannot set link state.\n");
goto error;
}
if (link_state == USB_SS_PORT_LS_U3) {
slot_id = xhci_find_slot_id_by_port(hcd, xhci,
wIndex + 1);
if (slot_id) {
/* unlock to execute stop endpoint
* commands */
spin_unlock_irqrestore(&xhci->lock,
flags);
xhci_stop_device(xhci, slot_id, 1);
spin_lock_irqsave(&xhci->lock, flags);
}
}
xhci_set_link_state(xhci, port_array, wIndex,
link_state);
spin_unlock_irqrestore(&xhci->lock, flags);
msleep(20); /* wait device to enter */
spin_lock_irqsave(&xhci->lock, flags);
temp = xhci_readl(xhci, port_array[wIndex]);
if (link_state == USB_SS_PORT_LS_U3)
bus_state->suspended_ports |= 1 << wIndex;
break;
case USB_PORT_FEAT_POWER:
/* FIXME Do not turn on BYT XHCI port 6 power,
* Disable this port's power to disable HSIC hub
*/
if ((xhci->quirks & XHCI_PORT_DISABLE_QUIRK) &&
(wIndex == 5)) {
temp = xhci_readl(xhci, port_array[wIndex]);
temp &= ~PORT_POWER;
xhci_writel(xhci, temp, port_array[wIndex]);
break;
}
/*
* Turn on ports, even if there isn't per-port switching.
* HC will report connect events even before this is set.
* However, khubd will ignore the roothub events until
* the roothub is registered.
*/
xhci_writel(xhci, temp | PORT_POWER,
port_array[wIndex]);
temp = xhci_readl(xhci, port_array[wIndex]);
xhci_dbg(xhci, "set port power, actual port %d status = 0x%x\n", wIndex, temp);
break;
case USB_PORT_FEAT_RESET:
temp = (temp | PORT_RESET);
xhci_writel(xhci, temp, port_array[wIndex]);
temp = xhci_readl(xhci, port_array[wIndex]);
xhci_dbg(xhci, "set port reset, actual port %d status = 0x%x\n", wIndex, temp);
break;
case USB_PORT_FEAT_REMOTE_WAKE_MASK:
xhci_set_remote_wake_mask(xhci, port_array,
wIndex, wake_mask);
temp = xhci_readl(xhci, port_array[wIndex]);
xhci_dbg(xhci, "set port remote wake mask, "
"actual port %d status = 0x%x\n",
wIndex, temp);
break;
case USB_PORT_FEAT_BH_PORT_RESET:
temp |= PORT_WR;
xhci_writel(xhci, temp, port_array[wIndex]);
temp = xhci_readl(xhci, port_array[wIndex]);
break;
case USB_PORT_FEAT_TEST:
if (!selector || selector >= 5 || !status_reg)
goto error;
/*
* Disable all Device Slots.
*/
for (i = 0; i < MAX_HC_SLOTS; i++) {
if (xhci->dcbaa->dev_context_ptrs[i]) {
if (xhci_queue_slot_control(xhci,
TRB_DISABLE_SLOT, i)) {
xhci_err(xhci,
"Disable slot[%d] failed!\n",
i);
goto error;
}
xhci_dbg(xhci, "Disable Slot[%d].\n", i);
}
}
/*
* All ports shall be in the Disable state (PP = 0)
*/
xhci_dbg(xhci, "Disable all port (PP = 0)\n");
num_ports = HCS_MAX_PORTS(xhci->hcs_params1);
for (i = 0; i < num_ports; i++) {
u32 __iomem *sreg =
&xhci->op_regs->port_status_base +
NUM_PORT_REGS*i;
temp = xhci_readl(xhci, sreg);
temp &= ~PORT_POWER;
xhci_writel(xhci, temp, sreg);
}
/* Set the Run/Stop (R/S) bit in the USBCMD
* register to a '0' and wait for HCHalted(HCH) bit
* in the USBSTS register, to transition to a '1'.
*/
xhci_dbg(xhci, "Stop controller\n");
command = xhci_readl(xhci, &xhci->op_regs->command);
command &= ~CMD_RUN;
xhci_writel(xhci, command, &xhci->op_regs->command);
if (handshake(xhci, &xhci->op_regs->status,
STS_HALT, STS_HALT, 100*100)) {
xhci_warn(xhci, "WARN: xHC CMD_RUN timeout\n");
return -ETIMEDOUT;
}
/*
* start to test
*/
xhci_dbg(xhci, "test case:");
switch (selector) {
case 1:
xhci_dbg(xhci, "TEST_J\n");
break;
case 2:
xhci_dbg(xhci, "TEST_K\n");
break;
case 3:
xhci_dbg(xhci, "TEST_SE0_NAK\n");
break;
case 4:
xhci_dbg(xhci, "TEST_PACKET\n");
break;
default:
xhci_dbg(xhci, "Invalide test case!\n");
goto error;
}
temp = xhci_readl(xhci, status_reg);
temp |= selector << 28;
xhci_writel(xhci, temp, status_reg);
break;
default:
goto error;
}
/* unblock any posted writes */
temp = xhci_readl(xhci, port_array[wIndex]);
break;
case ClearPortFeature:
if (!wIndex || wIndex > max_ports)
goto error;
wIndex--;
temp = xhci_readl(xhci, port_array[wIndex]);
if (temp == 0xffffffff) {
retval = -ENODEV;
break;
}
/* FIXME: What new port features do we need to support? */
temp = xhci_port_state_to_neutral(temp);
switch (wValue) {
case USB_PORT_FEAT_SUSPEND:
temp = xhci_readl(xhci, port_array[wIndex]);
xhci_dbg(xhci, "clear USB_PORT_FEAT_SUSPEND\n");
xhci_dbg(xhci, "PORTSC %04x\n", temp);
if (temp & PORT_RESET)
goto error;
if ((temp & PORT_PLS_MASK) == XDEV_U3) {
if ((temp & PORT_PE) == 0)
goto error;
xhci_set_link_state(xhci, port_array, wIndex,
XDEV_RESUME);
spin_unlock_irqrestore(&xhci->lock, flags);
msleep(20);
spin_lock_irqsave(&xhci->lock, flags);
xhci_set_link_state(xhci, port_array, wIndex,
XDEV_U0);
}
bus_state->port_c_suspend |= 1 << wIndex;
slot_id = xhci_find_slot_id_by_port(hcd, xhci,
wIndex + 1);
if (!slot_id) {
xhci_dbg(xhci, "slot_id is zero\n");
goto error;
}
xhci_ring_device(xhci, slot_id);
break;
case USB_PORT_FEAT_POWER:
/*
* Turn off ports even if there isn't per-port
* swithing. HC will report connect events even
* before this is set. However, khubd will ignore
* the roothub events until the roothub is registered.
*/
xhci_writel(xhci, temp & ~PORT_POWER,
port_array[wIndex]);
temp = xhci_readl(xhci, port_array[wIndex]);
xhci_dbg(xhci, "clear PP, port %d status = 0x%x\n",
wIndex, temp);
break;
case USB_PORT_FEAT_C_SUSPEND:
bus_state->port_c_suspend &= ~(1 << wIndex);
case USB_PORT_FEAT_C_RESET:
case USB_PORT_FEAT_C_BH_PORT_RESET:
case USB_PORT_FEAT_C_CONNECTION:
case USB_PORT_FEAT_C_OVER_CURRENT:
case USB_PORT_FEAT_C_ENABLE:
case USB_PORT_FEAT_C_PORT_LINK_STATE:
xhci_clear_port_change_bit(xhci, wValue, wIndex,
port_array[wIndex], temp);
break;
case USB_PORT_FEAT_ENABLE:
xhci_disable_port(hcd, xhci, wIndex,
port_array[wIndex], temp);
break;
default:
goto error;
}
break;
default:
error:
/* "stall" on error */
retval = -EPIPE;
}
spin_unlock_irqrestore(&xhci->lock, flags);
return retval;
}
int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
u16 wIndex, char *buf, u16 wLength)
{
struct xhci_hcd *xhci = hcd_to_xhci(hcd);
int max_ports, max_portpmsc;
unsigned long flags;
u32 temp, status;
int retval = 0;
__le32 __iomem **port_array;
__le32 __iomem **portpmsc_array;
int slot_id;
struct xhci_bus_state *bus_state;
u16 link_state = 0;
u16 wake_mask = 0;
u8 selector;
max_ports = xhci_get_ports(hcd, &port_array);
max_portpmsc = xhci_get_portpmsc(hcd, &portpmsc_array);
bus_state = &xhci->bus_state[hcd_index(hcd)];
spin_lock_irqsave(&xhci->lock, flags);
switch (typeReq) {
case GetHubStatus:
/* No power source, over-current reported per port */
memset(buf, 0, 4);
break;
case GetHubDescriptor:
/* Check to make sure userspace is asking for the USB 3.0 hub
* descriptor for the USB 3.0 roothub. If not, we stall the
* endpoint, like external hubs do.
*/
if (hcd->speed == HCD_USB3 &&
(wLength < USB_DT_SS_HUB_SIZE ||
wValue != (USB_DT_SS_HUB << 8))) {
xhci_dbg(xhci, "Wrong hub descriptor type for "
"USB 3.0 roothub.\n");
goto error;
}
xhci_hub_descriptor(hcd, xhci,
(struct usb_hub_descriptor *) buf);
break;
case DeviceRequest | USB_REQ_GET_DESCRIPTOR:
if ((wValue & 0xff00) != (USB_DT_BOS << 8))
goto error;
if (hcd->speed != HCD_USB3)
goto error;
memcpy(buf, &usb_bos_descriptor,
USB_DT_BOS_SIZE + USB_DT_USB_SS_CAP_SIZE);
temp = xhci_readl(xhci, &xhci->cap_regs->hcs_params3);
buf[12] = HCS_U1_LATENCY(temp);
put_unaligned_le16(HCS_U2_LATENCY(temp), &buf[13]);
spin_unlock_irqrestore(&xhci->lock, flags);
return USB_DT_BOS_SIZE + USB_DT_USB_SS_CAP_SIZE;
case GetPortStatus:
if (!wIndex || wIndex > max_ports)
goto error;
wIndex--;
status = 0;
temp = xhci_readl(xhci, port_array[wIndex]);
if (temp == 0xffffffff) {
retval = -ENODEV;
break;
}
xhci_dbg(xhci, "get port status, actual port %d status = 0x%x\n", wIndex, temp);
/* wPortChange bits */
if (temp & PORT_CSC)
status |= USB_PORT_STAT_C_CONNECTION << 16;
if (temp & PORT_PEC)
status |= USB_PORT_STAT_C_ENABLE << 16;
if ((temp & PORT_OCC))
status |= USB_PORT_STAT_C_OVERCURRENT << 16;
if ((temp & PORT_RC))
status |= USB_PORT_STAT_C_RESET << 16;
/* USB3.0 only */
if (hcd->speed == HCD_USB3) {
if ((temp & PORT_PLC))
status |= USB_PORT_STAT_C_LINK_STATE << 16;
if ((temp & PORT_WRC))
status |= USB_PORT_STAT_C_BH_RESET << 16;
if ((temp & PORT_CEC))
status |= USB_PORT_STAT_C_CONFIG_ERROR << 16;
}
if (hcd->speed != HCD_USB3) {
if ((temp & PORT_PLS_MASK) == XDEV_U3
&& (temp & PORT_POWER))
status |= USB_PORT_STAT_SUSPEND;
}
if ((temp & PORT_PLS_MASK) == XDEV_RESUME &&
!DEV_SUPERSPEED(temp)) {
if ((temp & PORT_RESET) || !(temp & PORT_PE))
goto error;
if (time_after_eq(jiffies,
bus_state->resume_done[wIndex])) {
xhci_dbg(xhci, "Resume USB2 port %d\n",
wIndex + 1);
bus_state->resume_done[wIndex] = 0;
clear_bit(wIndex, &bus_state->resuming_ports);
xhci_set_link_state(xhci, port_array, wIndex,
XDEV_U0);
xhci_dbg(xhci, "set port %d resume\n",
wIndex + 1);
slot_id = xhci_find_slot_id_by_port(hcd, xhci,
wIndex + 1);
if (!slot_id) {
xhci_dbg(xhci, "slot_id is zero\n");
goto error;
}
xhci_ring_device(xhci, slot_id);
bus_state->port_c_suspend |= 1 << wIndex;
bus_state->suspended_ports &= ~(1 << wIndex);
} else {
/*
* The resume has been signaling for less than
* 20ms. Report the port status as SUSPEND,
* let the usbcore check port status again
* and clear resume signaling later.
*/
status |= USB_PORT_STAT_SUSPEND;
}
}
if ((temp & PORT_PLS_MASK) == XDEV_U0
&& (temp & PORT_POWER)
&& (bus_state->suspended_ports & (1 << wIndex))) {
bus_state->suspended_ports &= ~(1 << wIndex);
if (hcd->speed != HCD_USB3)
bus_state->port_c_suspend |= 1 << wIndex;
}
if (temp & PORT_CONNECT) {
status |= USB_PORT_STAT_CONNECTION;
status |= xhci_port_speed(temp);
}
if (temp & PORT_PE)
status |= USB_PORT_STAT_ENABLE;
if (temp & PORT_OC)
status |= USB_PORT_STAT_OVERCURRENT;
if (temp & PORT_RESET)
status |= USB_PORT_STAT_RESET;
if (temp & PORT_POWER) {
if (hcd->speed == HCD_USB3)
status |= USB_SS_PORT_STAT_POWER;
else
status |= USB_PORT_STAT_POWER;
}
/* Update Port Link State for super speed ports*/
if (hcd->speed == HCD_USB3) {
xhci_hub_report_link_state(xhci, &status, temp);
/*
* Verify if all USB3 Ports Have entered U0 already.
* Delete Compliance Mode Timer if so.
*/
xhci_del_comp_mod_timer(xhci, temp, wIndex);
}
if (bus_state->port_c_suspend & (1 << wIndex))
status |= 1 << USB_PORT_FEAT_C_SUSPEND;
xhci_dbg(xhci, "Get port status returned 0x%x\n", status);
put_unaligned(cpu_to_le32(status), (__le32 *) buf);
break;
case SetPortFeature:
selector = wIndex >> 8;
if (wValue == USB_PORT_FEAT_LINK_STATE)
link_state = (wIndex & 0xff00) >> 3;
if (wValue == USB_PORT_FEAT_REMOTE_WAKE_MASK)
wake_mask = wIndex & 0xff00;
wIndex &= 0xff;
if (!wIndex || wIndex > max_ports)
goto error;
wIndex--;
temp = xhci_readl(xhci, port_array[wIndex]);
if (temp == 0xffffffff) {
retval = -ENODEV;
break;
}
temp = xhci_port_state_to_neutral(temp);
/* FIXME: What new port features do we need to support? */
switch (wValue) {
case USB_PORT_FEAT_SUSPEND:
temp = xhci_readl(xhci, port_array[wIndex]);
if ((temp & PORT_PLS_MASK) != XDEV_U0) {
/* Resume the port to U0 first */
xhci_set_link_state(xhci, port_array, wIndex,
XDEV_U0);
spin_unlock_irqrestore(&xhci->lock, flags);
msleep(10);
spin_lock_irqsave(&xhci->lock, flags);
}
/* In spec software should not attempt to suspend
* a port unless the port reports that it is in the
* enabled (PED = ??1??,PLS < ??3??) state.
*/
temp = xhci_readl(xhci, port_array[wIndex]);
if ((temp & PORT_PE) == 0 || (temp & PORT_RESET)
|| (temp & PORT_PLS_MASK) >= XDEV_U3) {
xhci_warn(xhci, "USB core suspending device "
"not in U0/U1/U2.\n");
goto error;
}
slot_id = xhci_find_slot_id_by_port(hcd, xhci,
wIndex + 1);
if (!slot_id) {
xhci_warn(xhci, "slot_id is zero\n");
goto error;
}
/* unlock to execute stop endpoint commands */
spin_unlock_irqrestore(&xhci->lock, flags);
xhci_stop_device(xhci, slot_id, 1);
spin_lock_irqsave(&xhci->lock, flags);
xhci_set_link_state(xhci, port_array, wIndex, XDEV_U3);
spin_unlock_irqrestore(&xhci->lock, flags);
msleep(10); /* wait device to enter */
spin_lock_irqsave(&xhci->lock, flags);
temp = xhci_readl(xhci, port_array[wIndex]);
bus_state->suspended_ports |= 1 << wIndex;
break;
case USB_PORT_FEAT_LINK_STATE:
temp = xhci_readl(xhci, port_array[wIndex]);
/* Disable port */
if (link_state == USB_SS_PORT_LS_SS_DISABLED) {
xhci_dbg(xhci, "Disable port %d\n", wIndex);
temp = xhci_port_state_to_neutral(temp);
/*
* Clear all change bits, so that we get a new
* connection event.
*/
temp |= PORT_CSC | PORT_PEC | PORT_WRC |
PORT_OCC | PORT_RC | PORT_PLC |
PORT_CEC;
xhci_writel(xhci, temp | PORT_PE,
port_array[wIndex]);
temp = xhci_readl(xhci, port_array[wIndex]);
break;
}
/* Put link in RxDetect (enable port) */
if (link_state == USB_SS_PORT_LS_RX_DETECT) {
xhci_dbg(xhci, "Enable port %d\n", wIndex);
xhci_set_link_state(xhci, port_array, wIndex,
link_state);
temp = xhci_readl(xhci, port_array[wIndex]);
break;
}
/* Software should not attempt to set
* port link state above '3' (U3) and the port
* must be enabled.
*/
if ((temp & PORT_PE) == 0 ||
(link_state > USB_SS_PORT_LS_U3)) {
xhci_warn(xhci, "Cannot set link state.\n");
goto error;
}
if (link_state == USB_SS_PORT_LS_U3) {
slot_id = xhci_find_slot_id_by_port(hcd, xhci,
wIndex + 1);
if (slot_id) {
/* unlock to execute stop endpoint
* commands */
spin_unlock_irqrestore(&xhci->lock,
flags);
xhci_stop_device(xhci, slot_id, 1);
spin_lock_irqsave(&xhci->lock, flags);
}
}
xhci_set_link_state(xhci, port_array, wIndex,
link_state);
spin_unlock_irqrestore(&xhci->lock, flags);
msleep(20); /* wait device to enter */
spin_lock_irqsave(&xhci->lock, flags);
temp = xhci_readl(xhci, port_array[wIndex]);
if (link_state == USB_SS_PORT_LS_U3)
bus_state->suspended_ports |= 1 << wIndex;
break;
case USB_PORT_FEAT_POWER:
/*
* Turn on ports, even if there isn't per-port switching.
* HC will report connect events even before this is set.
* However, khubd will ignore the roothub events until
* the roothub is registered.
*/
xhci_writel(xhci, temp | PORT_POWER,
port_array[wIndex]);
temp = xhci_readl(xhci, port_array[wIndex]);
xhci_dbg(xhci, "set port power, actual port %d status = 0x%x\n", wIndex, temp);
break;
case USB_PORT_FEAT_RESET:
temp = (temp | PORT_RESET);
xhci_writel(xhci, temp, port_array[wIndex]);
temp = xhci_readl(xhci, port_array[wIndex]);
xhci_dbg(xhci, "set port reset, actual port %d status = 0x%x\n", wIndex, temp);
break;
/*
* For downstream facing ports (these): one hub port is put
* into test mode according to USB2 11.24.2.13, then the hub
* must be reset (which for root hub now means rmmod+modprobe,
* or else system reboot). See EHCI 2.3.9 and 4.14 for info
* about the EHCI-specific stuff.
*/
case USB_PORT_FEAT_TEST:
#ifdef CONFIG_HOST_COMPLIANT_TEST
retval = xhci_port_test(hcd, selector, wIndex, flags);
if (retval < 0) {
xhci_err(xhci, "USB2 Host Test Fail!!!\n");
goto error;
}
#endif
break;
case USB_PORT_FEAT_REMOTE_WAKE_MASK:
xhci_set_remote_wake_mask(xhci, port_array,
wIndex, wake_mask);
temp = xhci_readl(xhci, port_array[wIndex]);
xhci_dbg(xhci, "set port remote wake mask, "
"actual port %d status = 0x%x\n",
wIndex, temp);
break;
case USB_PORT_FEAT_BH_PORT_RESET:
temp |= PORT_WR;
xhci_writel(xhci, temp, port_array[wIndex]);
temp = xhci_readl(xhci, port_array[wIndex]);
break;
default:
goto error;
}
/* unblock any posted writes */
temp = xhci_readl(xhci, port_array[wIndex]);
break;
case ClearPortFeature:
if (!wIndex || wIndex > max_ports)
goto error;
wIndex--;
temp = xhci_readl(xhci, port_array[wIndex]);
if (temp == 0xffffffff) {
retval = -ENODEV;
break;
}
/* FIXME: What new port features do we need to support? */
temp = xhci_port_state_to_neutral(temp);
switch (wValue) {
case USB_PORT_FEAT_SUSPEND:
temp = xhci_readl(xhci, port_array[wIndex]);
xhci_dbg(xhci, "clear USB_PORT_FEAT_SUSPEND\n");
xhci_dbg(xhci, "PORTSC %04x\n", temp);
if (temp & PORT_RESET)
goto error;
if ((temp & PORT_PLS_MASK) == XDEV_U3) {
if ((temp & PORT_PE) == 0)
goto error;
xhci_set_link_state(xhci, port_array, wIndex,
XDEV_RESUME);
spin_unlock_irqrestore(&xhci->lock, flags);
msleep(20);
spin_lock_irqsave(&xhci->lock, flags);
xhci_set_link_state(xhci, port_array, wIndex,
XDEV_U0);
}
bus_state->port_c_suspend |= 1 << wIndex;
slot_id = xhci_find_slot_id_by_port(hcd, xhci,
wIndex + 1);
if (!slot_id) {
xhci_dbg(xhci, "slot_id is zero\n");
goto error;
}
xhci_ring_device(xhci, slot_id);
break;
case USB_PORT_FEAT_C_SUSPEND:
bus_state->port_c_suspend &= ~(1 << wIndex);
case USB_PORT_FEAT_C_RESET:
case USB_PORT_FEAT_C_BH_PORT_RESET:
case USB_PORT_FEAT_C_CONNECTION:
case USB_PORT_FEAT_C_OVER_CURRENT:
case USB_PORT_FEAT_C_ENABLE:
case USB_PORT_FEAT_C_PORT_LINK_STATE:
case USB_PORT_FEAT_C_PORT_CONFIG_ERROR:
xhci_clear_port_change_bit(xhci, wValue, wIndex,
port_array[wIndex], temp);
break;
case USB_PORT_FEAT_ENABLE:
xhci_disable_port(hcd, xhci, wIndex,
port_array[wIndex], temp);
break;
default:
goto error;
}
break;
default:
error:
/* "stall" on error */
retval = -EPIPE;
}
spin_unlock_irqrestore(&xhci->lock, flags);
return retval;
}
static int xhci_create_usb3_bos_desc(struct xhci_hcd *xhci, char *buf,
u16 wLength)
{
int i, ssa_count;
u32 temp;
u16 desc_size, ssp_cap_size, ssa_size = 0;
bool usb3_1 = false;
desc_size = USB_DT_BOS_SIZE + USB_DT_USB_SS_CAP_SIZE;
ssp_cap_size = sizeof(usb_bos_descriptor) - desc_size;
/* does xhci support USB 3.1 Enhanced SuperSpeed */
if (xhci->usb3_rhub.min_rev >= 0x01 && xhci->usb3_rhub.psi_uid_count) {
/* two SSA entries for each unique PSI ID, one RX and one TX */
ssa_count = xhci->usb3_rhub.psi_uid_count * 2;
ssa_size = ssa_count * sizeof(u32);
desc_size += ssp_cap_size;
usb3_1 = true;
}
memcpy(buf, &usb_bos_descriptor, min(desc_size, wLength));
if (usb3_1) {
/* modify bos descriptor bNumDeviceCaps and wTotalLength */
buf[4] += 1;
put_unaligned_le16(desc_size + ssa_size, &buf[2]);
}
if (wLength < USB_DT_BOS_SIZE + USB_DT_USB_SS_CAP_SIZE)
return wLength;
/* Indicate whether the host has LTM support. */
temp = readl(&xhci->cap_regs->hcc_params);
if (HCC_LTC(temp))
buf[8] |= USB_LTM_SUPPORT;
/* Set the U1 and U2 exit latencies. */
if ((xhci->quirks & XHCI_LPM_SUPPORT)) {
temp = readl(&xhci->cap_regs->hcs_params3);
buf[12] = HCS_U1_LATENCY(temp);
put_unaligned_le16(HCS_U2_LATENCY(temp), &buf[13]);
}
if (usb3_1) {
u32 ssp_cap_base, bm_attrib, psi;
int offset;
ssp_cap_base = USB_DT_BOS_SIZE + USB_DT_USB_SS_CAP_SIZE;
if (wLength < desc_size)
return wLength;
buf[ssp_cap_base] = ssp_cap_size + ssa_size;
/* attribute count SSAC bits 4:0 and ID count SSIC bits 8:5 */
bm_attrib = (ssa_count - 1) & 0x1f;
bm_attrib |= (xhci->usb3_rhub.psi_uid_count - 1) << 5;
put_unaligned_le32(bm_attrib, &buf[ssp_cap_base + 4]);
if (wLength < desc_size + ssa_size)
return wLength;
/*
* Create the Sublink Speed Attributes (SSA) array.
* The xhci PSI field and USB 3.1 SSA fields are very similar,
* but link type bits 7:6 differ for values 01b and 10b.
* xhci has also only one PSI entry for a symmetric link when
* USB 3.1 requires two SSA entries (RX and TX) for every link
*/
offset = desc_size;
for (i = 0; i < xhci->usb3_rhub.psi_count; i++) {
psi = xhci->usb3_rhub.psi[i];
psi &= ~USB_SSP_SUBLINK_SPEED_RSVD;
if ((psi & PLT_MASK) == PLT_SYM) {
/* Symmetric, create SSA RX and TX from one PSI entry */
put_unaligned_le32(psi, &buf[offset]);
psi |= 1 << 7; /* turn entry to TX */
offset += 4;
if (offset >= desc_size + ssa_size)
return desc_size + ssa_size;
} else if ((psi & PLT_MASK) == PLT_ASYM_RX) {
/* Asymetric RX, flip bits 7:6 for SSA */
psi ^= PLT_MASK;
}
put_unaligned_le32(psi, &buf[offset]);
offset += 4;
if (offset >= desc_size + ssa_size)
return desc_size + ssa_size;
}
}
/* ssa_size is 0 for other than usb 3.1 hosts */
return desc_size + ssa_size;
}
static void xhci_print_cap_regs(struct xhci_hcd *xhci)
{
u32 temp;
u32 hci_version;
xhci_dbg(xhci, "xHCI capability registers at %p:\n", xhci->cap_regs);
temp = readl(&xhci->cap_regs->hc_capbase);
hci_version = HC_VERSION(temp);
xhci_dbg(xhci, "CAPLENGTH AND HCIVERSION 0x%x:\n",
(unsigned int) temp);
xhci_dbg(xhci, "CAPLENGTH: 0x%x\n",
(unsigned int) HC_LENGTH(temp));
xhci_dbg(xhci, "HCIVERSION: 0x%x\n", hci_version);
temp = readl(&xhci->cap_regs->hcs_params1);
xhci_dbg(xhci, "HCSPARAMS 1: 0x%x\n",
(unsigned int) temp);
xhci_dbg(xhci, " Max device slots: %u\n",
(unsigned int) HCS_MAX_SLOTS(temp));
xhci_dbg(xhci, " Max interrupters: %u\n",
(unsigned int) HCS_MAX_INTRS(temp));
xhci_dbg(xhci, " Max ports: %u\n",
(unsigned int) HCS_MAX_PORTS(temp));
temp = readl(&xhci->cap_regs->hcs_params2);
xhci_dbg(xhci, "HCSPARAMS 2: 0x%x\n",
(unsigned int) temp);
xhci_dbg(xhci, " Isoc scheduling threshold: %u\n",
(unsigned int) HCS_IST(temp));
xhci_dbg(xhci, " Maximum allowed segments in event ring: %u\n",
(unsigned int) HCS_ERST_MAX(temp));
temp = readl(&xhci->cap_regs->hcs_params3);
xhci_dbg(xhci, "HCSPARAMS 3 0x%x:\n",
(unsigned int) temp);
xhci_dbg(xhci, " Worst case U1 device exit latency: %u\n",
(unsigned int) HCS_U1_LATENCY(temp));
xhci_dbg(xhci, " Worst case U2 device exit latency: %u\n",
(unsigned int) HCS_U2_LATENCY(temp));
temp = readl(&xhci->cap_regs->hcc_params);
xhci_dbg(xhci, "HCC PARAMS 0x%x:\n", (unsigned int) temp);
xhci_dbg(xhci, " HC generates %s bit addresses\n",
HCC_64BIT_ADDR(temp) ? "64" : "32");
xhci_dbg(xhci, " HC %s Contiguous Frame ID Capability\n",
HCC_CFC(temp) ? "has" : "hasn't");
xhci_dbg(xhci, " HC %s generate Stopped - Short Package event\n",
HCC_SPC(temp) ? "can" : "can't");
/* FIXME */
xhci_dbg(xhci, " FIXME: more HCCPARAMS debugging\n");
temp = readl(&xhci->cap_regs->run_regs_off);
xhci_dbg(xhci, "RTSOFF 0x%x:\n", temp & RTSOFF_MASK);
/* xhci 1.1 controllers have the HCCPARAMS2 register */
if (hci_version > 0x100) {
temp = readl(&xhci->cap_regs->hcc_params2);
xhci_dbg(xhci, "HCC PARAMS2 0x%x:\n", (unsigned int) temp);
xhci_dbg(xhci, " HC %s Force save context capability",
HCC2_FSC(temp) ? "supports" : "doesn't support");
xhci_dbg(xhci, " HC %s Large ESIT Payload Capability",
HCC2_LEC(temp) ? "supports" : "doesn't support");
xhci_dbg(xhci, " HC %s Extended TBC capability",
HCC2_ETC(temp) ? "supports" : "doesn't support");
}
}
