//------------------------------------------------------------------------------
/// USB interrupt subroutine
///
/// This function is called each time a USB interrupt occurs.
/// The following USB DEVICE events are taken in charge:
/// - VBus On / Off
/// - Start Of Frame
/// - Suspend
/// - Wake-Up
/// - Resume
/// - Reset
/// - Start of frame
///
/// The following USB HOST events are taken in charge:
/// - Device connection
/// - Device Disconnection
/// - Start Of Frame
/// - ID pin change
/// - SOF (or Keep alive in low speed) sent
/// - Wake up on USB line detected
///
/// The following USB HOST events are taken in charge:
/// - HNP success (Role Exchange)
/// - HNP failure (HNP Error)
///
/// For each event, the user can launch an action by completing
/// the associate define (See conf_usb.h file to add action upon events)
///
/// Note: Only interrupts events that are enabled are processed
//------------------------------------------------------------------------------
void usb_general_interrupt(void)
{
    //TRACE_DEBUG("usb_general_interrupt\n\r");

    // ---------- DEVICE events management -----------------------------------
    // -----------------------------------------------------------------------

    //- VBUS state detection
    // -----------------------------------------------------------------------
    /// Arbitrer
    // -----------------------------------------------------------------------
    if (Is_usb_vbus_transition() && Is_usb_vbus_interrupt_enabled() 
        && Is_usb_id_device()) {
        Usb_ack_vbus_transition();

        if (Is_usb_vbus_high()) {
            usb_connected = TRUE;
            Usb_vbus_on_action();
            Usb_send_event(EVT_USB_POWERED);
            //jcb    Usb_enable_reset_interrupt();
            //usb_start_device();
            USBD_Connect();//Usb_attach();
        }
        else {
            TRACE_DEBUG("VBUS low\n\r");
            USBD_Disconnect();
            Usb_device_stop_hnp();
            TRACE_DEBUG("Usb_select_device4\n\r");
            Usb_select_device();
            Clear_all_user_request();
            Usb_vbus_off_action();
            usb_connected = FALSE;
            usb_configuration_nb = 0;
            Usb_send_event(EVT_USB_UNPOWERED);
        }

    }

    // -----------------------------------------------------------------------
    /// Device
    // -----------------------------------------------------------------------
    // - Device start of frame received
    if (Is_usb_sof() && Is_sof_interrupt_enabled()) {
        //  TRACE_DEBUG_WP("F");   // device
        Usb_ack_sof();
        Usb_sof_action();
        //sof_seen_in_session = TRUE;
        otg_last_sof_received = UDFNUML;  // store last frame number received
    }

    // -----------------------------------------------------------------------
    /// Device
    // -----------------------------------------------------------------------
    // - Device Suspend event (no more USB activity detected)
    if (Is_usb_suspend()) { //&& Is_suspend_interrupt_enabled()) {
        //TRACE_DEBUG_WP("D\n\r");
        // 1st : B-PERIPH mode ?
        if (Is_usb_id_device()) {
            // HNP Handler
            TRACE_DEBUG("HNP Handler\n\r");
            //TRACE_DEBUG("device_state = %d\n\r", device_state);
            //TRACE_DEBUG("b_uut_device_state = %d\n\r", b_uut_device_state);
            if (Is_host_requested_hnp() // "b_hnp_enable" feature received
            && (Is_session_started_with_srp() || Is_user_requested_hnp() )) {
                if (otg_device_nb_hnp_retry == 0) {
                    otg_features_supported &= ~USBFeatureRequest_OTG_B_HNP_ENABLE;
                }
                else {
                    Ack_user_request_hnp();
                    Usb_ack_hnp_error_interrupt();
                    Usb_ack_role_exchange_interrupt();
                    Usb_enable_role_exchange_interrupt();
                    Usb_enable_hnp_error_interrupt();
                    Usb_device_initiate_hnp();
                    otg_device_nb_hnp_retry--;
                }
            }
            else
            {
                // Remote wake-up handler
                //TRACE_DEBUG("Remote wake-up handler\n\r");
                //TRACE_DEBUG("device_state = %d\n\r", device_state);
                //TRACE_DEBUG("b_uut_device_state = %d\n\r", b_uut_device_state);
                if ((remote_wakeup_feature == ENABLE) && (usb_configuration_nb != 0))
                {
                    //TRACE_DEBUG("enabled\n\r");
                    // After that user can execute "Usb_initiate_remote_wake_up()" to initiate a remote wake-up
                    // Note that the suspend interrupt flag SUSPI must still be set to enable upstream resume
                    // So the SUSPE enable bit must be cleared to avoid redundant interrupt
                    // ****************
                    // Please note also that is Vbus is lost during an upstream resume (Host disconnection),
                    // the RMWKUP bit (used to initiate remote wake up and that is normally cleared by hardware when sent)
                    // remains set after the event, so that a good way to handle this feature is :
                    //            Usb_initiate_remote_wake_up();
                    //            while (Is_usb_pending_remote_wake_up())
                    //            {
                    //              if (Is_usb_vbus_low())
                    //              {
                    //                // Emergency action (reset macro, etc.) if Vbus lost during resuming
                    //                break;
                    //              }
                    //            }
                    //            Usb_ack_remote_wake_up_start();
                    // ****************
                }
                else {
                    //TRACE_DEBUG("disabled: %d %d\n\r", usb_configuration_nb, remote_wakeup_feature);
                    // No remote wake-up supported
                    Usb_send_event(EVT_USB_SUSPEND);
                }
            }
        }
        else
        {
            //TRACE_DEBUG("ici\n\r");
            // A-PERIPH mode (will cause a session end, handled in usb_host_task.c)
            Usb_send_event(EVT_USB_SUSPEND);
            Usb_suspend_action();
            //jcb   Usb_ack_suspend();
        }
    }
   
    // -----------------------------------------------------------------------
    /// Device
    // -----------------------------------------------------------------------
    // - Wake up event (USB activity detected): Used to resume
    if (Is_usb_wake_up() && Is_swake_up_interrupt_enabled()) {
        TRACE_DEBUG("W\n\r");
        Usb_unfreeze_clock();
        Usb_send_event(EVT_USB_WAKE_UP);
    }

    // -----------------------------------------------------------------------
    /// Device
    // -----------------------------------------------------------------------
    // - Resume state bus detection
    if (Is_usb_resume() && Is_resume_interrupt_enabled()) {
        TRACE_DEBUG("Resume state bus detect\n\r");
        Usb_send_event(EVT_USB_RESUME);
    }

    // -----------------------------------------------------------------------
    /// Device
    // -----------------------------------------------------------------------
    // - USB bus reset detection
    if (Is_usb_reset()&& Is_reset_interrupt_enabled()) {
        TRACE_DEBUG_WP("B\n\r");
        if (Is_usb_id_host()) {
            //TRACE_DEBUG_WP("id_host\n\r");
            dev_configure_endpoint(EP_CONTROL,
            TYPE_CONTROL,
            DIRECTION_OUT,
            SIZE_64,
            ONE_BANK,
            NYET_DISABLED);
        }
        // First initialization is important to be synchronized
        // A reset must first have been received
        if (device_state == A_PERIPHERAL) {
            //TRACE_DEBUG_WP("r A_PERIPHERAL\n\r");
            otg_last_sof_received = UDFNUML;
            otg_last_sof_stored   = UDFNUML;
            Usb_ack_sof();
            Usb_enable_sof_interrupt();
            reset_received = TRUE;
            Timer16_set_counter(0);
        }
        Usb_reset_action();
        Usb_send_event(EVT_USB_RESET);
    }

    // ---------- OTG events management ------------------------------------
    // ---------------------------------------------------------------------

    // -----------------------------------------------------------------------
    /// Arbitrer
    // -----------------------------------------------------------------------
    // - OTG HNP Success detection
    if (Is_usb_role_exchange_interrupt() && Is_role_exchange_interrupt_enabled()) {
        //     TRACE_DEBUG("OTG HNP detect\n\r");
        Usb_ack_role_exchange_interrupt();
        Host_ack_device_connection();
        Host_ack_device_disconnection();
        Otg_send_event(EVT_OTG_HNP_SUCCESS);
        End_session_with_srp();
        Clear_otg_features_from_host();
        if (Is_usb_id_host()) {
            // HOST (A- or B-) mode
            if ((device_state != A_PERIPHERAL) && (device_state != A_END_HNP_WAIT_VFALL)) {
                static volatile unsigned int jcb;
                // Current mode is A-HOST, device will take the A-PERIPHERAL role
                b_uut_device_state = B_PERIPHERAL;
                device_state = A_PERIPHERAL;
                usb_connected = FALSE;
                usb_configuration_nb = 0;
                Usb_select_device();
                USBD_Connect();//Usb_attach();
                Usb_unfreeze_clock();
                Usb_disable_role_exchange_interrupt();
                Usb_disable_hnp_error_interrupt();
                Usb_device_stop_hnp();
                Usb_ack_reset();
                Timer16_set_counter(0);
                Usb_freeze_clock();                // USB clock can be freezed to slow down events and condition detection
                //jcb       while (Timer16_get_counter_low() != 20);
                jcb=0;
                while( jcb <100000){ jcb++; }

                Usb_unfreeze_clock();
                reset_received = FALSE;
                Usb_disable_sof_interrupt();       // will be set in the next OTG Timer IT (mandatory)

                Usb_enable_suspend_interrupt();
                Usb_enable_reset_interrupt();
                dev_configure_endpoint(EP_CONTROL,
                    TYPE_CONTROL,
                    DIRECTION_OUT,
                    SIZE_64,
                    ONE_BANK,
                    NYET_DISABLED);
            }
        }
        else {
            // In B_HOST mode, the HNPREQ bit must not be cleared because it releases the bus in suspend mode (and sof can't start)
            if ((b_uut_device_state != B_HOST) && (b_uut_device_state != B_END_HNP_SUSPEND)) {
                static volatile unsigned int jcb2;
                // Current mode is B-PERIPHERAL, device will go into B-HOST role
                End_session_with_srp();
                Clear_otg_features_from_host();
                b_uut_device_state = B_HOST;
                device_state = DEVICE_ATTACHED;
                usb_connected = FALSE;
                usb_configuration_nb = 0;
                TRACE_DEBUG("Select host 3\n\r");
                Usb_select_host();

                TRACE_DEBUG("Send reset\n\r");
                Host_send_reset();     // send the first RESET
                while (Host_is_reset());
                TRACE_DEBUG("Reset passed\n\r");

                jcb2=0;
                while( jcb2 <1000000){ jcb2++; }
                Host_enable_sof();     // start Host (sof)
                Usb_disable_role_exchange_interrupt();
                Usb_disable_hnp_error_interrupt();
                Clear_all_user_request();

                TRACE_DEBUG("Select host 3\n\r");
            }
        }
    }

    // -----------------------------------------------------------------------
    /// Arbitrer
    // -----------------------------------------------------------------------
    // - OTG HNP Failure detection
    if (Is_usb_hnp() && Is_usb_hnp_error_interrupt()&& Is_hnp_error_interrupt_enabled()) {
        TRACE_DEBUG("OTG HNP failure\n\r");
        Usb_device_stop_hnp();
        Usb_disable_role_exchange_interrupt();
        Usb_disable_hnp_error_interrupt();
        Usb_ack_hnp_error_interrupt();
        if (Is_usb_id_device()) {
            Otg_send_event(EVT_OTG_HNP_ERROR);
            Clear_all_user_request();
        }
    }   

    // ---------- HOST events management -----------------------------------
    // ---------------------------------------------------------------------

    // -----------------------------------------------------------------------
    /// Arbitrer
    // -----------------------------------------------------------------------
    // - ID pin change detection
    if(Is_usb_id_transition()&&Is_usb_id_interrupt_enabled()) {
        TRACE_DEBUG("ID pin change\n\r");
        TRACE_DEBUG("device_state = %d\n\r", device_state);
        TRACE_DEBUG("b_uut_device_state = %d\n\r", b_uut_device_state);
        Usb_device_stop_hnp();
        Clear_all_user_request();
        if(Is_usb_id_device()) { 
            g_usb_mode = USB_MODE_DEVICE;
        }
        else {
            g_usb_mode = USB_MODE_HOST;
        }
        Usb_ack_id_transition();
        if( g_usb_mode != g_old_usb_mode) { // Basic Debounce
            if(Is_usb_id_device()) { // Going into device mode
                Usb_send_event(EVT_USB_DEVICE_FUNCTION);
                b_uut_device_state = B_IDLE;
                device_state = DEVICE_UNATTACHED;
                id_changed_to_host_event = DISABLE;
            }
            else {                  // Going into host mode
                b_uut_device_state = B_IDLE;
                device_state = DEVICE_UNATTACHED;
                Usb_send_event(EVT_USB_HOST_FUNCTION);
                id_changed_to_host_event = ENABLE;
            }
            Usb_id_transition_action();
            TRACE_INFO("Pin Id changed\n\r");
        }
    }
   
    // -----------------------------------------------------------------------
    /// Host
    // -----------------------------------------------------------------------
    // - The device has been disconnected
    // JCB to be fix
    if(Is_device_disconnection() && Is_host_device_disconnection_interrupt_enabled()) {
        TRACE_DEBUG("device disconnect\n\r");
        host_disable_all_pipe();
        Host_ack_device_disconnection();
        device_state=DEVICE_DISCONNECTED;
        Usb_send_event(EVT_HOST_DISCONNECTION);
        TRACE_INFO("Device disconnected\n\r");
        Host_device_disconnection_action();
        Clear_all_user_request();
    }

    // -----------------------------------------------------------------------
    /// Host
    // -----------------------------------------------------------------------
    // - Device connection
    if(Is_device_connection() && Is_host_device_connection_interrupt_enabled()) {
        TRACE_DEBUG("device connect\n\r");
        Host_ack_device_connection();
        host_disable_all_pipe();
        Host_device_connection_action();
    }

    // -----------------------------------------------------------------------
    /// Host
    // -----------------------------------------------------------------------
    // - Host Start of frame has been sent
    if (Is_host_sof() && Is_host_sof_interrupt_enabled()) {
        //TRACE_DEBUG_WP("_");  // host
        Host_ack_sof();
        Usb_send_event(EVT_HOST_SOF);
        private_sof_counter++;

        // delay timeout management for interrupt tranfer mode in host mode
#if ((USB_HOST_PIPE_INTERRUPT_TRANSFER==ENABLE) && (TIMEOUT_DELAY_ENABLE==ENABLE))
        if (private_sof_counter>=250) {  // Count 1/4 sec
            private_sof_counter=0;
            for(i=0;i<MAX_EP_NB;i++) {
                if(it_pipe_str[i].enable==ENABLE) {
                    save_pipe_nb=Host_get_selected_pipe();
                    Host_select_pipe(i);
                    if((++it_pipe_str[i].timeout>TIMEOUT_DELAY) && (Host_get_pipe_type()!=TYPE_INTERRUPT)) {
                        it_pipe_str[i].enable=DISABLE;
                        it_pipe_str[i].status=PIPE_DELAY_TIMEOUT;
                        Host_stop_pipe_interrupt(i);
                        if (is_any_interrupt_pipe_active()==FALSE) {   // If no more transfer is armed
                            if (g_sav_int_sof_enable==FALSE) {
                                Host_disable_sof_interrupt();
                            }
                        }
                        it_pipe_str[i].handle(PIPE_DELAY_TIMEOUT,it_pipe_str[i].nb_byte_processed);
                    }
                    Host_select_pipe(save_pipe_nb);
                }
            }
        }
#endif  // (USB_HOST_PIPE_INTERRUPT_TRANSFER==ENABLE) && (TIMEOUT_DELAY_ENABLE==ENABLE))
        Host_sof_action();
    }

    // -----------------------------------------------------------------------
    /// Host
    // -----------------------------------------------------------------------
    // - Host Wake-up has been received
    if (Is_host_hwup() && Is_host_hwup_interrupt_enabled()) {
        TRACE_DEBUG("Host wake up\n\r");
        Host_disable_hwup_interrupt();  // Wake up interrupt should be disable host is now wake up !
        Host_disable_remote_wakeup_interrupt();
        // CAUTION HWUP can be cleared only when USB clock is active (not frozen)!
        Usb_unfreeze_clock();           // Enable clock on USB interface
        Host_enable_sof();              // start sending SOF
        Host_ack_hwup();                // Clear HWUP interrupt flag
        Host_ack_remote_wakeup();
        Usb_send_event(EVT_HOST_HWUP);  // Send software event
        Usb_send_event(EVT_HOST_REMOTE_WAKEUP);
        Host_hwup_action();             // Map custom action
        if (Is_usb_hnp()) {
            Usb_host_reject_hnp();
            Usb_disable_hnp_error_interrupt();
            Usb_disable_role_exchange_interrupt();
        }
        Host_send_resume();
    }

    // -----------------------------------------------------------------------
    /// Host
    // -----------------------------------------------------------------------
    // Remote Wake Up has been received
    if (Is_host_remote_wakeup_interrupt_enabled() && Is_host_remote_wakeup()) {
        TRACE_DEBUG("Remote wake up\n\r");
        Host_disable_remote_wakeup_interrupt();
        Host_disable_hwup_interrupt();
        Host_ack_remote_wakeup();
        Host_ack_hwup();                // Clear HWUP interrupt flag
        Usb_unfreeze_clock();           // Enable clock on USB interface
        Host_enable_sof();     // start sending SOF
        Usb_send_event(EVT_HOST_REMOTE_WAKEUP);
        Usb_send_event(EVT_HOST_HWUP);  // Send software event
        if (Is_usb_hnp()) {
            Usb_host_reject_hnp();
            Usb_disable_hnp_error_interrupt();
            Usb_disable_role_exchange_interrupt();
        }
        Host_send_resume();
    }
}
Exemple #2
0
__interrupt void usb_general_interrupt()
#endif
{
   #if (USB_HOST_PIPE_INTERRUPT_TRANSFER == ENABLE)
   U8 i;
   U8 save_pipe_nb;
   #endif
// ---------- DEVICE events management -----------------------------------
#if (USB_DEVICE_FEATURE == ENABLED)
  //- VBUS state detection
   if (Is_usb_vbus_transition() && Is_usb_vbus_interrupt_enabled())
   {
      Usb_ack_vbus_transition();
      if (Is_usb_vbus_high())
      {
         usb_connected = TRUE;
         Usb_vbus_on_action();
         Usb_send_event(EVT_USB_POWERED);
			Usb_enable_reset_interrupt();
         usb_start_device();
			Usb_attach();
      }
      else
      {
         Usb_vbus_off_action();
         usb_connected = FALSE;
         usb_configuration_nb = 0;
         Usb_send_event(EVT_USB_UNPOWERED);
      }
   }
  // - Device start of frame received
   if (Is_usb_sof() && Is_sof_interrupt_enabled())
   {
      Usb_ack_sof();
      Usb_sof_action();
   }
  // - Device Suspend event (no more USB activity detected)
   if (Is_usb_suspend() && Is_suspend_interrupt_enabled())
   {
      Usb_ack_suspend();
      Usb_enable_wake_up_interrupt();
      Usb_ack_wake_up();                 // clear wake up to detect next event
      Usb_freeze_clock();
      Usb_send_event(EVT_USB_SUSPEND);
      Usb_suspend_action();
   }
  // - Wake up event (USB activity detected): Used to resume
   if (Is_usb_wake_up() && Is_swake_up_interrupt_enabled())
   {
      Usb_unfreeze_clock();
      Usb_ack_wake_up();
      Usb_disable_wake_up_interrupt();
      Usb_wake_up_action();
      Usb_send_event(EVT_USB_WAKE_UP);
   }
  // - Resume state bus detection
   if (Is_usb_resume() && Is_resume_interrupt_enabled())
   {
      Usb_disable_wake_up_interrupt();
      Usb_ack_resume();
      Usb_disable_resume_interrupt();
      Usb_resume_action();
      Usb_send_event(EVT_USB_RESUME);
   }
  // - USB bus reset detection
   if (Is_usb_reset()&& Is_reset_interrupt_enabled())
   {
      Usb_ack_reset();
      usb_init_device();
      Usb_reset_action();
      Usb_send_event(EVT_USB_RESET);
   }
#endif// End DEVICE FEATURE MODE

// ---------- HOST events management -----------------------------------
#if (USB_HOST_FEATURE == ENABLED && USB_DEVICE_FEATURE == ENABLED)
  // - ID pin change detection
   if(Is_usb_id_transition()&&Is_usb_id_interrupt_enabled())
   {
      if(Is_usb_id_device())
      { g_usb_mode=USB_MODE_DEVICE;}
      else
      { g_usb_mode=USB_MODE_HOST;}
      Usb_ack_id_transition();
      if( g_usb_mode != g_old_usb_mode) // Basic Debounce
      {
         if(Is_usb_id_device()) // Going to device mode
         {
            Usb_send_event(EVT_USB_DEVICE_FUNCTION);
         }
         else                   // Going to host mode
         {
            Usb_send_event(EVT_USB_HOST_FUNCTION);
         }
         Usb_id_transition_action();
         LOG_STR_CODE(log_id_change);
         #if ( ID_PIN_CHANGE_GENERATE_RESET == ENABLE)
        // Hot ID transition generates wdt reset
            #ifndef  AVRGCC
               Wdt_change_16ms(); while(1);
            #else
               Wdt_change_enable(); while(1);
            #endif
         #endif
      }
   }
#endif
#if (USB_HOST_FEATURE == ENABLED)
  // - The device has been disconnected
   if(Is_device_disconnection() && Is_host_device_disconnection_interrupt_enabled())
   {
      host_disable_all_pipe();
      Host_ack_device_disconnection();
      device_state=DEVICE_DISCONNECTED;
      Usb_send_event(EVT_HOST_DISCONNECTION);
      LOG_STR_CODE(log_device_disconnect);
      Host_device_disconnection_action();
   }
  // - Device connection
   if(Is_device_connection() && Is_host_device_connection_interrupt_enabled())
   {
      Host_ack_device_connection();
      host_disable_all_pipe();
      Host_device_connection_action();
   }
  // - Host Start of frame has been sent
   if (Is_host_sof() && Is_host_sof_interrupt_enabled())
   {
      Host_ack_sof();
      Usb_send_event(EVT_HOST_SOF);
      private_sof_counter++;

      // delay timeout management for interrupt tranfer mode in host mode
      #if ((USB_HOST_PIPE_INTERRUPT_TRANSFER==ENABLE) && (TIMEOUT_DELAY_ENABLE==ENABLE))
      if (private_sof_counter>=250)   // Count 1/4 sec
      {
         private_sof_counter=0;
         for(i=0;i<MAX_EP_NB;i++)
         {
            if(it_pipe_str[i].enable==ENABLE)
            {
               save_pipe_nb=Host_get_selected_pipe();
               Host_select_pipe(i);
               if((++it_pipe_str[i].timeout>TIMEOUT_DELAY) && (Host_get_pipe_type()!=TYPE_INTERRUPT))
               {
                  it_pipe_str[i].enable=DISABLE;
                  it_pipe_str[i].status=PIPE_DELAY_TIMEOUT;
                  Host_stop_pipe_interrupt(i);
                  if (is_any_interrupt_pipe_active()==FALSE)    // If no more transfer is armed
                  {
                     if (g_sav_int_sof_enable==FALSE)
                     {
                        Host_disable_sof_interrupt();
                     }
                  }
                  it_pipe_str[i].handle(PIPE_DELAY_TIMEOUT,it_pipe_str[i].nb_byte_processed);
               }
               Host_select_pipe(save_pipe_nb);
            }
         }
      }
      #endif  // (USB_HOST_PIPE_INTERRUPT_TRANSFER==ENABLE) && (TIMEOUT_DELAY_ENABLE==ENABLE))
      Host_sof_action();
   }
  // - Host Wake-up has been received
   if (Is_host_hwup() && Is_host_hwup_interrupt_enabled())
   {
      Host_disable_hwup_interrupt();  // Wake up interrupt should be disable host is now wake up !
      // CAUTION HWUP can be cleared only when USB clock is active (not frozen)!
      Pll_start_auto();               // First Restart the PLL for USB operation
      Wait_pll_ready();               // Get sure pll is lock
      Usb_unfreeze_clock();           // Enable clock on USB interface
      Host_ack_hwup();                // Clear HWUP interrupt flag
      Usb_send_event(EVT_HOST_HWUP);  // Send software event
      Host_hwup_action();             // Map custom action
   }
#endif // End HOST FEATURE MODE
}